Page 1
Instruction Sheet
UQFP SERIES
Ultra Quiet Fan Panels
(220V Models)
THANK YOU
Thank you for purchasing the UQFP Series Ultra Quiet Fan Panel. Please read these instructions
thoroughly before installing this product.
PRODUCT FEATURES
- Reliable cooling with minimal noise
- Local and remote status notification
- On-board processor controls fan speed
proportional to enclosure temperature
I-00467 Rev -
Page 2
SPECIFICATIONS
UQFP-2 & UQFP-2D/IUQFP-2 & IUQFP-2D
Current Draw: 270 mA @ 5V DC (UQFP-2/IUQFP-2) Airflow: 50 CFM @ Full Speed
310 mA @ 5V DC (UQFP-2D/IUQFP-2D) RPM: 1900 @ Full Speed
Noise: 24 dB @ Full Speed
UQFP-4 & UQFP-4D/IUQFP-4 & IUQFP-4D
Current Draw: 510 mA @ 5V DC (UQFP-4/IUQFP-4) Airflow: 100 CFM @ Full Speed
560 mA @ 5V DC (UQFP-4D/IUQFP-4D) RPM: 1900 @ Full Speed
Noise: 27 dB @ Full Speed
UQFP-2/IUQFP-2
UQFP-2D/IUQFP-2D
UQFP-4/IUQFP-4
UQFP-4D/IUQFP-4D
Page 2
Page 3
FUNCTIONS
Models UQFP-2 & UQFP-4/IUQFP-2 & IUQFP-4
(UQFP-4 Model Shown)
FAN
POWER (GREEN)
FRONT VIEW
(YELLOW)
OVERTEMP
(RED)
OVERTEMP ALARM OUTPUT
DO NOT OPEN. NO USER SERVICEABLE PARTS INSIDE.
OVER
5VDC
TEMP
2A
ALARM
(N.O.)
5V DC INPUT JACK
TEMPERATURE PROBE
REAR VIEW
POWER
FAN
(GREEN): This LED indicates that the unit is receiving power.
(YELLOW): When rack temperature reaches 81OF (27OC) this LED will begin to flash
indicating that the fans have turned on. It will continue flashing proportional to the fan speed,
as long as the fans are on.
OVERTEMP
(RED): If rack temperature reaches 100OF (37OC) this LED will light indicating an
over temperature condition within the rack.
OVERTEMP ALARM OUTPUT: This normally open dry contact closure will provide an alarm to an
external (remote) monitoring system if your enclosure reaches overtemp condition.
5V DC INPUT JACK: Power supply connector
TEMPERATURE PROBE:
Remote temperature sensor. (9' long)
Page 3
Page 4
Models UQFP-2D & UQFP-4D/IUQFP-2D & IUQFP-4D
(UQFP-4D Model Shown)
FAN (YELLOW)
POWER (GREEN)
DISPLAY
ALARM
(RED)
FRONT VIEW
POWER (GREEN): This indicates that the unit is receiving power.
FAN
(YELLOW): When rack temperature reaches 81OF (27OC), this LED will begin to flash indicating
that the fans have turned on. It will continue flashing proportional to the fan speed, as long as the fans
are on.
ALARM
temperature condition within the rack. See Alarm Set Point Button
(RED): At the factory preset overtemp of 100OF (37OC), this LED will light indicating an over
instructions below to change the
overtemp alarm setting.
DISPLAY: The display will indicate the rack temperature and provide a read-out of the following fault
codes during one of these conditions:
OVERTEMP: The temperature of the enclosure has risen above the alarm set point. Inspect
airflow intake and output for obstructions. Additional cooling capacity may be required.
FAN FAULT: One or more of the fans has stopped. Check all fans for obstruction.
If problem persists, call Technical Support at (800) 266-7225.
Page 4
Page 5
OVERTEMP ALARM OUTPUT
FAN FAULT ALARM OUTPUT
DO NOT OPEN. NO USER SERVICEABLE PARTS INSIDE.
5VDC
FAN
OVER
2A
FAULT
TEMP
ALARM
ALARM
(N.O.)
(N.O.)
REAR VIEW
ALARM SET POINT BUTTON
CONTROL SETTINGS
PUSH
Press once to view the current
overtemp alarm setting.
Each additional push will raise
the overtemp alarm setting
by 1
To toggle between Fahrenheit
and Celsius, press and hold for
3 seconds.
5V DC INPUT JACK
TEMPERATURE PROBE
O
.
SIDE VIEW
ALARM SET POINT BUTTON:
- To change display from Fahrenheit to Celsius, press and hold Alarm Set Point Button for 3 seconds.
- To view alarm set point, simply press and release the Alarm Set Point Button once.
- To change the factory preset alarm set point, repeatedly press the Alarm Set Point Button until
O
desired temperature is displayed. Factory preset overtemp alarm set point is 100
O
Adjustment range is from 95
FAN FAULT
/ OVERTEMP ALARM OUTPUT:
to 115OF (35O to 46OC)
F (37OC).
These normally open dry contact closures will provide an alarm to an external (remote) monitoring
system if your enclosure experiences a fan fault or overtemp condition.
5V DC INPUT JACK: Power supply connector
TEMPERATURE PROBE:
Remote temperature sensor (9' long).
Page 5
Page 6
INSTALLATION
UQFP-2D (left) & UQFP-4D (right) Shown.
CONTROL SETTINGS
PUSH
Press once to view the current
overtemp alarm setting.
Each additional push will raise
the overtemp alarm setting
To toggle between Fahrenheit
by 1
O
and Celsius, press and hold for
.
3 seconds.
FAULT
ALARM
(N.O.)
5VDC
2A
OVER
TEMP
FAN
ALARM
(N.O.)
WIRE TIE HERE
TIE SADDLE
TEMPERATURE PROBE
CONTROL SETTINGS
PUSH
Press once to view the current
overtemp alarm setting.
Each additional push will raise
the overtemp alarm setting
To toggle between Fahrenheit
by 1
O
and Celsius, press and hold for
.
3 seconds.
FAN
FAULT
ALARM
(N.O.)
OVER
TEMP
ALARM
(N.O.)
5VDC
2A
WIRE TIE HERE
TECH TIP: Ensure that you have access to the rear of the panel to make connections and
configure settings once mounted. If access to rear of unit is limited, cable management and
setting configurations must be done prior to mounting the panel.
1) Route Temperature Probe, Alarm Output, and Power Supply wires along the rear of the
panel as shown above. Tie points are provided to route wires left or right. Do not allow wires
to interfere with fan operation.
2) Using tie saddle included, mount the temperature probe wire into highest available area inside
of rack. In order to achieve proper temperature sensing, the probe should be installed near
the top of the rack. The probe is provided with a generous 9' lead.
3) (220V models only) Select appropriate wall plug for your region and attach to
provided power supply. Connect power supply to power source.
Page 6
Page 7
THERMAL MANAGEMENT GUIDELINES
- Mount fan panel in highest available location of enclosure.
- Use vent blockers to cover any vent at the top of side panels.
- Do not place vent panels within six rackspaces below fan panel. Cover any of these spaces.
- If heat producing equipment is in the middle of the rack, use a 3 space vent panel at
the bottom
- Use a 2 space vent panel if heat producing equipment is at the bottom of the enclosure.
UQFP-4D
(SHOWN)
Page 7
VENT PANEL
Page 8
WARRANTY
Middle Atlantic Products, Inc. (the "Company") warrants the UQFP Series Ultra Quiet Fan Panels to be
free from defects in material or workmanship under normal use and conditions for a period of three (3)
years from date of shipment by the Company.
The Company's entire liability to the purchaser, and the purchaser's (or any other parties) sole and
exclusive remedy, under this warranty shall be limited, at the Company's option, to either (a) return of
and refund of the price paid for, or (b) repair or replacement at the Company's factory of the products
purchased, or any part or parts thereof, which the Company has determined to be defective after
inspection thereof at the Company's factory.
This warranty does not cover damage due to acts of God, accident, misuse, abuse or negligence by
parties other than the Company, or any modification or alteration of the products. In addition, this warranty
does not cover damage due to improper handling, assembly, installation or maintenance.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY
BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES
WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OF THE
PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER PARTY)
HEREUNDER, IF ANY, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCTS
PAID TO THE COMPANY.
Corporate Headquarters
Corporate Voice 973-839-1011 - Fax 973-839-1976
International Voice +1 973-839-1011 - Fax +1 973-831-4982
middleatlantic.com - info@middleatlantic.com
Middle Atlantic Canada
113 Iber Road - Ottawa, ON - K2S 1E7
Voice 613-836-2501 - Fax 613-836-2690
middleatlantic.ca - customerservicecanada@middleatlantic.ca
Factory Distribution
USA: NJ - CA - IL Canada: ON - BC
At Middle Atlantic Products we are always listening. Your comments are welcome.
Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company.
Page 8
30% Recycled Paper
Loading...