Microtek GNC M 710S XXXX User Manual

710S 17” LCD MONITOR

USER’S MANUAL

Table of Contents

FCC Compliance Statement .................................................................... ii

Introduction .............................................................................................. 1

Factory-preset Modes .............................................................................2

Specifications .......................................................................................... 3

Installing the Monitor ...............................................................................5

Control Functions .....................................................................................7

Appendix ............................................................................................... 14

Signal connector pin assignment ......................................................... 16

FCC Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Caution:

To comply with the limits for an FCC Class B computing device, always use the shielded signal cord supplied with this unit.

The Federal Communications Commission warns that changes or modifications of the unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CE mark for Class B ITE (Following European standard EN55022/1998; EN61000-3-2/ 1995; EN61000-3-3/1995, EN55024/1998, EN60950/1992+A1+A2+A3+A4+A11)

iii

Radio Frequency Interference Statement

Warning:

This is a Class B product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.

Canadian Doc Notice

For Class B Computing Devices

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications.

“Le présent appareil numérique n’èmet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class B prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada”

Important Safety Instructions

Please read the following instructions carefully. This manual should be retained for future use.

1. To clean the LCD monitor screen, make sure the monitor is in the power off mode. Unplug the monitor from its power source before cleaning it. Do not spray liquid cleaners directly onto the unit. Stand away from the LCD monitor and spray cleaning solution onto a rag. Without applying excessive pressure, clean the screen with the slightly dampened rag.

2. Do not place your LCD monitor near a window. Exposing the monitor to rain, water, moisture or sunlight can severely damage it.

3. Do not place anything on top of the monitor-to-PC signal cord. Make sure the cord is placed in an area where it will not be stepped on.

4. Do not apply pressure to the LCD screen. Excessive pressure may cause permanent damage to the display.

5. Do not remove the cover or attempt to service this unit by yourself,as you may void the warranty. Servicing of any nature should be performed only by an authorized technician.

6. Safe storage of the LCD monitor is in the range of -4°F to 140°F (–20°C to +60°C). Storing your LCD monitor outside this range could result in permanent damage.

7. If any of the following occurs, immediately unplug your monitor and call an authorized technician.

• The power or monitor-to-PC signal cord is frayed or damaged.

• Liquid has been spilled onto the monitor, or it has been exposed to rain.

• The monitor has been dropped or the case has been damaged.

8. Use the monitor only with the supplied adapter. In case of loss, contact the retailer or service center.

9. If you lose the power cord, you must purchase a power cord of the same type and configuration.

• Japan GVCTF type, 3 wires or with ground-wire; T-mark approval is required.

• U.S. GVW-1; 18AWG X 3C; SVT with national approval as UL and/or CSA approval/number(s)

• Europe GVDE/ÖVE and/or KEMA approval; H05VV-F, 3G, 0.75mm2, or equivalent.

The power cord should bear the name of the manufacturer and state the type of cord that it is.

Introduction

Before installing your monitor

Read this manual carefully .

P AY ATTENTION to all Warning and Caution messages.

DO NOT use computer components not recommended by the manufacturer.

Do not attempt to service the monitor yourself. If a problem occurs, contact the manufacturer’s authorized service center .

About your monitor

This monitor is a microprocessor-controlled color monitor that uses a TFT LCD panel. The monitor conforms to EP A Energy Star and VESA DPMS (Display Power Management Signaling) power management standards.

RGB Mode

This monitor is equipped with a microprocessor that identifies your computer’s video mode and allows you to adjust the setting.

Factory-preset Modes

Table 1 shows standard video mode setting that has been pre-adjusted at the factory for accurate video display. These settings are stored in the monitor’s memory .

Table 1. Factory-preset Modes

Mode

NEC

VGA

SVGA

XGA

SXGA

Macintosh

Resolution

640 x 400

640 x 350

720 x 400

640 x 480

800 x 600

1024 x 768

1280 x 1024

640 x 480

H-Freq. (KHz)

24.83

31.47

37.86

37.5

35.16

37.88

48.08

46.87

48.36

56.47

63.98

V-Freq (Hz)

56.4

56.3

60.3

72.2

66.7

832 x 624

1024 x 768

49.7

48.78

60.241

74.55

74.927

+ 14 hidden pages