Microtek ArtixScan DI 6260S, ArtixScan DI6250S, ArtixScan DI6240S, ArtixScan TS 630S Installation guide

Start Here

nstalling your Microtek ArtixScan DI 6260S/6250S/6240S &

ArtixScan TS 630S

Unpack Contents

Unpack your scanner package and check for major components.

1. Scanner

2. Hi-Speed USB cable

3. Software CDs/DVDs

4. Power cord

5. Power adapter

Install Software

Important: You must install software before connecting

your scanner. Always close any open programs, and turn off Anti-virus utilities before installing software.

PC:

A. Place the Microtek Software CD/DVD

into a drive, and follow the on-screen instructions to install the scanner driver and software.

B. Restart your computer at the end of all

software installation.

NOTE: If the Microtek Software Installer screen does not come up automatically, double-click the following in succession: “My Computer”; the CD/ DVD-ROM icon; then cdsetup.exe to start the installer program.

MAC:

A. Place the Microtek Software CD/DVD

(ScanPotter) into a drive, and double-click

the ScanPotter installer icon to install ScanPotter.

B. Install the remaining software

components, then restart your computer at the end of all software installation.

NOTE: After rebooting your Macintosh, the Microtek software will attempt to locate your scanner on the system. Since this is your first install and you have not yet connected the scanner, simply ignore the message that appears and proceed to the next step.

Open Feed Tray & Output Tray

Before

After

Open Feed Tray

A. Lift up the Document Feed Tray to the

highest level which can be opened.

Document Feed Tray

C. Tilt the Document Feed Tray backwards

in the direction as the arrow shown to fully open the tray.

B. Along the tracks of the two sides of the

Document Feed Tray, slide the feed tray down until the supporters of the tray touch the bottom edge of the tracks.

Slide the feed tray down

D. Along the tracks of the two sides of the

Document Feed Tray, slide the feed tray down until it locks in place.

Open Output Tray and Paper Stabilizer

Bring down the a) Document Output Tray and b) Paper Stabilizer from the top towards the direction as shown in the graph.

Document Output Tray

Paper Stabilizer

Connect Scanner

To the power adapter

A. Connect the power adapter to the back of the scanner.

B. Plug one end of the power cord into the power adapter, and plug the other end of the

power cord into a wall outlet or other power source.

To the Hi-Speed USB cable

C. Connect one end of the cable to your computer.

D. Connect the other end of the cable to the scanner’s USB port.

E. Press and hold the Power button ( ) until the orange LED lights on. Once the scanner is

powered on, the green LED will be lighted up, and the 7-segment LED display (SSD) will also be activated as well.

The system will detect the scanner automatically.

Power button

Customize the Function Button

Your scanner is equipped with one Select, one Scan/Stop and one Favorite buttons, plus a LED display, used to automate a number of customized and predefined operations, such as scanning to a file, sending an image to your printer, scanning for OCR, etc. Customizing is done through the Scanner Button Settings interface in the ScanWizard DI, refer to the scanner’s User’s Manual for more details.

LED display: Display the selected function button number.

• Select: Toggle through the numbers of predefined function buttons (F1 to F5).

• Scan/Stop: Start scan immediately or cancel a ongoing scan job.

• Favorite: Carry out the function defined to the Favorite button directly.

Position Documents

The scanner supports scanning of document in various materials, such as A4 printouts, insurance papers, legal documents, postcards, credit cards, business cards, and etc. A stack of up to 100 sheets of papers (17 to 18 lbs/63.75 to 67.5 g/m² ) or 2 pieces of cards (1.3 mm/

0.05”) can be fed in the scanner’s Document Feed Tray at one time. Paper sizes can range from 2.75” x 3.149” (70 mm x 80 mm) to 8.85” x 118” (225 mm x 3000 mm) or to 8.85” x 25” (225 mm x 635 mm) depending on the scanner you purchased.

To load a stack of documents

1. Before loading the stack of papers onto the scanner’s Document Feed Tray, please fan the papers and then align the top edges of the papers neatly.

2. Load the stack of papers onto the scanner’s Document Feed Tray, with the side to be scanned facing down and the top edge facing toward the feeder.

Push the stack of papers into the tray until the paper’s edge touches the bottom edge of the feeder.

WARNING: The document feeder is not designed for scanning photos; doing so may damage your originals. Microtek accepts no responsibility for damage that may arise from misuse of equipment.

3. Align the stack of originals with the center of the Document Feed Tray by sliding the two Guide Arms toward the stacked papers if needed.

4. Pull out the Output Tray Extender to carry the longer paper if needed.

5. Lift up either of two Paper Stoppers to keep a stack of output papers stay neatly and tightly inside the Document Output Tray if needed.

Document Feed Tray

Guide Arms

Output Tray Extender

NOTE: For more details on how to adjust the Output Tray Extender and Paper Stoppers, Please refer to the section “Output Tray Notice” in the guide.

Paper Stopper (1)

Paper Stopper (2)

To Load Cards

1. Slide the Guide Arms toward the center of the feed tray and free up the enough space to put the card inside.

2. Load and center the card onto the scanner’s Document Feed Tray, with the front side facing up and the top edge directing toward the feeder.

NOTE: When the card is loaded, launch ScanWizard DI. Then, switch the Normal Scan button to the Card Scan button and click it to start your card scanning.

Output Tray Notice

The Paper Stopper is designed to prevent the paper stacks falling in a mess after they were scanned and output into the output tray. Before scanning a stack of papers, please follow the steps below to fix the Paper Stopper into the right position in the tray, in order to keep output papers stay neatly in the tray after the scan.

1. Pull out the Output Tray Extender.

2. Lift up either the Paper Stopper 1 or 2, depending on the length of the paper.

3. Take out one piece of paper from the stacks and put it in the output tray, laying it completely flat and bringing the top or bottom edge of it into contact with the bottom of the scanner.

4. Push back the Output Tray Extender until the Paper Stopper touches the edge of the paper.

Finally, load the papers to be scanned into the feed tray to start your scanning.

Load the paper inside the space between the stopper and the output slot of the scanner.

Align the paper against the side of output slot located at the bottom of the scanner.

NOTE: The settling position for the Paper Stopper on the tray must be equivalent to the length of the paper. Incorrect positioning of the Paper Stopper will result in disorders and mess for the after-scanned outputs.

Be sure the stopper is lightly against the edge of the paper.

+ 11 hidden pages