Pneumatic Double Location Shuttle
Heat Press Manual
APDS-15/20
CONTENTS
I. Assembly Drawing -----------------------------------------------------------------------------------2
II. Technical Parameters ------------------------------------------------------------------------------2
III. Operation Process -------------------------------------------------------------------------------3-4
IV. Maintenance ------------------------------------------------------------------------------------------5
V. Trouble Shooting For Transfer Print Quality------------------------------------------------6
VI. Circuit Diagram -------------------------------------------------------------------------------------6
VII. Explosion View -------------------------------------------------------------------------------------7
-1-
I. Assembly Drawing
Air PP
1
ƻ
Emergency Stop Button
5
ƻ
Shuttle Handle
2
ƻ
Start Switch
6
ƻ
Pneumatic Valve
II. Technical Parameters
1. Model No.: APDS-15/20
2. Machine Dimensions: 970*860*600mm
3. Heat Platen Size: 40x50cm,40x60cm
4. Printable Articles Max Size: 400*600mm*30mm
5. Voltage: 220V/ 3 Phase; 120V/ 1 Phase
6. Power: 220V/ 1.8KW ; 110V/ 1.2KW
7. Recommend Setting: Time: 30~280s; 180~210ć.
Time Range: 0~999s
Maximum Temp: 225°C
Heating Tube Power: 1.8KW* 1pc
8. Packaging size:1050*950*700mm
9. Gross Weight: 97kg
3
ƻ
Air Pressure Adjust Knob
7
ƻ
Air Filter
4
ƻ
GY-04 Digital Controller
-2-
III. Operation Process
ColdPortHotPort
lay showsy shows
1. How to adjust the pressure:
1. Connect the heat press with air compressor or air sources.
2. Lift up the cap of air valve as the picture shown
3. Revolve the cap anticlockwise, the air pressure goes down; contrariwise, the air pressure goes up; when you
finish the pressure adjustment, push down the cap.
4. Suggested air pressure is 0.4~0.5Mpa/ 70-80Psi. It depends on the transfer materials.
2. Set temperature required
Turn on power switch, temperature
light is ON. The digital display shows
.
3. Set time required
Press button after temperature
setting and the
on. Select with arrows the time
according to different transfer
material.
time light is
Press
on (C denotes Celsius). Press
arrows “Ƹ”or“” to select “ć”or
“” (F denotes Fahrenheit)
according to your habits.
Press
the display shows the temperature
starts to rise. “CD-L” shows the time
counting down during your transfer.
button, the light is
button after time setting;
Press
is on. Select with arrows the
temperature according to different
transfer material (Normally
180к~200к)
Note: There are two small port in
front side of the digital display.
If the real temperature is lower than
digital controller shown, you can
adjust the “hot port”; Clockwise to
raise temperature; anticlockwise to
reduce temperature.
button, the temp light
-3-
4. Printing methods
Step 1: Make sure the cord is connected well to the wall socket. Place the object (i.e. T-shirt) on press bed, and
transfer paper with images facing down the object, adjust pressure to your requirement, and turn on the power.
Step 2: Set the temperature and time required, then temperature starts to rise.
Step 3: When the temperature rises to the set temperature, the buzzer sends out a short sound. Press two green
start-up switches with both hands, the heat platen will close down automatically. Time is counting down;
once time is up, the heat platen will open automatically.
Step 4: Then you can use the shuttle handle to move the heat platen to the other side, and repeat the step 2 to
step 3.
Step 5: Consult the Transfer Paper instructions on whether to peel cold or hot, Here are suggested Pressing time
guidelines for different transfer paper.
Ink-Jet Transfer Paper (fabric) 14-18 seconds
Laser Copier/Printer Transfer Paper (fabric) 18-25 seconds
Sublimation Transfers (onto Fabrics) 25-30 seconds
Sublimation Transfers (onto FR-Plastic/Woods) 60-70 seconds
5. Recommendations:
1) Ceramic tile transfer: (Mugs & Plates transfer is similar)
Set temperature: 180ć.
Set time: 15 seconds
2) T-shirt transfer:
Set temperature: 180ć.
Set time: (chemical fiber use for sublimation transfer paper: 30-50 seconds; pure cotton use for T-shirt
transfer paper: 10-20 seconds)
3) Aluminum Sheet transfer
Set temperature: 180ć
Set time: 45 seconds
Emergency:
If any emergency happens, please press the red emergency stop button. After settled the emergency, please turn
the button clockwise and let it resume original status, and the machine will also resume working status.
NOTE:
1. Please switch off the machine power control valve if there is any problem.
2. The suitable air pressure is 0.4-0.5Mpa or 75-80Psi, neither too high (too high air pressure can destroy the
machine), nor too low (lower air pressure can’t let the heat platen work smoothly.)
3. Suggestion to power off for 1-2 hours after continuous working for 6-8 hours.
V. Maintenance
1. Air pressure
Checking the lubricating oil If it’s enough in the Cylinder. Use the pressure knob on the Air Regulator to adjust the
pressure, turn toward "+"direction to add the pressure, "-"direction to reduce the pressure.
2. Heat Platen Not Goes Down: If digital display show normally, but when you press green start button, the
heat platen not goes down
-4-
1). The limit value under the bottom platen doesn’t touch the counting down switch because of its too high position.
ć
ćDŽ
n.
temp and time according the operationtemp and time according the operatio
you are using it or not.you are using it or
4). If you are not able to s4). If you are not able
Please loosen the value’s screw a little to make it longer.
2). Checking the circuit connecting with green start-up switch if it’s with problem.
3. No action after turn on the machine
1). Check the plug whether it connects well or whether it is broken.
2). Check the power switch or digital controller whether it is broken.
3). Check the fuse whether it has been burnt out.
4). Indicating light is on, but no display on screen, check the 5 cable of Railway transformer. If it’s loosening,
showing the problem is poor connection. If they connects well, showing that the Transformer is faulty.
4. The display screen are working well, but no temperature increasing on the heat platen.
1). Check whether the thermocouple of the heat platen touches well. If the thermocouple is loose, the display will
show 255 and machine keeps beeping.
2). Check if the indicating light of solid-state relay is on, if not, check if the relay or digital controller is broken.
3). If you already changed the new solid-state relay but the heat platen still can’t heating up, check if the heat platen
is faulty or the heat platen’s power cable is loose, need to change by new heat platen.
5. The heat platen works well, but suddenly the display screen show 255к
1). Check whether the thermocouple of the heat platen touches well.
2). If the thermocouple touches well but stills show 255к, then it is faulty.
6. The machine is heating during 0~180
the numbers on display jumps irregularly.
1). Check whether the thermocouple of the heat platen touches well.
2). If the thermocouple is good, It shows that the program of digital controller is broken, which namely IC or is
broken, need to change by new controller.
7. The temperature is out of control: Set 180ć
1). It means the solid-state relay is broken, out of control, need to change the relay.
2). Or the digital controller is faulty and it keeps conveying electric to relay, need to change controller.
8. The setting temp and time becomes abnormal after exchange the heat platen
Please reset the temp and time according the operation process manual.
9. Other notice
1). In order to prolong the machine service life, please add the lubrication oil regularly on the joints.
2). In order to keep the heat platen's good transfer effect, you need to protect the heat platen carefully whenever
you are using it or not.
3). Please keep the machine in dry place.
4). If you are not able to solve the electrical parts problem, please kindly contact the supplier and get technical
support.
, but display number jumps to above 200ć or 300ć suddenly, or
ˈbut the actual temperature is above 200
.
IV. Trouble shooting for transfer print quality
1. If the print color is pale: the temperature is too low / the pressure is not correct / or not pressed long enough.
2. If the print color is too brown or the transfer paper is almost burnt: reduce the setting temperature
2. If the print is blurring: too much transfer time causes proliferation.
3. If print color is different/ partial transfer effect is not good enough: the pressure is not enough / or not pressed
long enough / or poor quality transfer paper.
4. If transfer paper stick to the object after transfer: the temperature is too high/ or poor quality printing ink.
-5-
VI. Circuit Diagram
K0.: Power switch K1: Start Switch FU: Fuse(15A/25A)
SJ: GY-04 Digital Controller HD: Pneumatic Controller J1: Industrial Relay
J2: Intermediate Relay Contacts L1: Indicator Light D: Pneumatic Electromagnetic Valve
EH1 EH2: Heating Pipe A-B: Thermocouple T1/T2: AC/DC Transformer
P: Emergency Stop Button
-6-
VII. Explosion View
Machine FrameMachine Fram
4 Heat Platen4 Heat Plate
No. Part Name Qty
1 Machine Frame 2
2 Slide Rail 1
3 Slide Rail Fixed Plate 1
4 Heat Platen 1
5 Heat Platen Cover 1
6 Anti-scald protect metal cover 1
7 Spring Protective Cover 2
8 Spring Fixed Cover 2
9Spring 1
10 Adaptor Plate 1
11 Air Regulating Valve 1
12 Start Switch 1
13 Side Plate 1
14 Air Filter 1
15 Back Plate 4
16 Power Cord 1
17 Electronic Parts Bracket 1
18 Upper Cover Plate 1
19 Air Cylinder 1
20 Spindle with Base 1
21 Controller Cover 1
22 Electromagnet 2
23 Casting Polyurethane 2
24 Emergency Stop Button 2
25 GY-04 Digital Controller 1
26 Front Handle 1
27 Under Plate 1
-7-
Loading...