www.liGo.co.uk
TELEPHONES |HEADSETS |TWO WAY RADIOS
PERSONAL CARE |BABY MONITORS |AND MUCH MORE
For all the latest product news, reviews and advice
from liGo, please visit www.liGo.co.uk/blog/
COBRA MT975
SET UP & USER GUIDE
Find more user manuals and product information at www.liGo.co.uk/manuals/
GET £5 OFF
*
your next purchase over £50
with voucher code:
liGo5reward
*
Not in conjunction
with any other oer
Product Features
• Two-Way Radio
with up to a 12 km (7.5 mile) range
•
8 Channels*
•
38 CTCSS Privacy Codes
• 83 DCS Privacy Codes
• 10 Channel Memor
y
• Backlit LCD Display
•
Battery Saver Circuitry
•
Battery Level Meter
• Maximum Range Extender
•
VOX Mode for Hands-Fr
ee Transmissions
•
Intercom Capable
• Baby Monitor Function
•
V
ibrAler
t
®
Silent Paging
•
Call Alert 10 Selectable Tones
•
Scan Channels, Privacy Codes, Memor
y
•
Dual Watch Programmable 2-Location Scan
•
Key Lock
• Auto Squelch
• Selectable ON/OFF "Roger Beep" Confirmation Tone
• Selectable ON/OFF
Keystroke Tone
• Combination Speaker/MicrophoneJack
• Belt Clip
*
Y
ou ar
e not allowed to use channels 1 and 2 in France.
This situation can change; please contact the Fr
ench radio
licensing authority for more information.
ENGLISH
Two-Way Radio Model MT 975
Printed in China Part No. 480-439-P Version A
1
1. Antenna
2. External Speaker/
Microphone Jack
3. ON/OFF Volume Knob
4. Mode Button
5. Channel Up/Down Buttons
6. Speaker/Microphone
7. Intercom Jack
8. Light/Max Range Button
9. Talk Button
10. Call Button
11. Lock/Enter Button
12. Belt Clip
13. Battery Compartment
14. Lock Tab
3
2
11
5
9
8
10
7
4
12
13
14
13
11
10
9
8
5
17
1
2
3
1.
Call Alert and VibrAlert Icon
2. Lock Icon
3. Keystroke Tone Icon
4. DCS Icon
5. Roger Beep Icon
6.
CTCSS Icon
7. Memory Channel Icon
8. Memory Location Number
9. Battery Level Meter
10. Privacy Code Numbers
11.
Dual W
atch Icon
12. VOX Icon
13. Power Saver Icon
14. Receive Icon
15.
Transmit Icon
16. Scan Icon
17. Baby Monitor Icon
18. Main Channel Number
6
4
7
6
12
15
14
18
16
NOTE: Estimated operation time on
full charge:12 hours.
These rechargeable batteries must be recycled
or disposed of properly in compliance with all
applicable laws. They must not be thr
own in the
rubbish bin. Some countries and local authorities
require recycling and have established collection
programs. Please contact your local waste disposal
authority for instructions.
WARNING: Do not put batteries into fire or expose
to high heat. They may explode.
For Charging microTALK®Radio(s):
1. Check to see that the
batteries have been inserted
properly. See above for battery
installation instructions.
2. Insert radio(s) into rapid
desktop charger as shown.
3.
Inser
t r
ound connector of adapter into
jack on back of char
ger.
4.
Plug adapter into electrical outlet. The wall
char
ger should be installed near the equipment
and easily accessible.
If charging light (one light per charging well) is
not ON, check position of radio. Radio should be
upright. The charge indicator light will stay ON
until the batteries are fully charged, then go out.
OPERATION
Product Information
This microTALK®radio has been manufactured to
meet all required standards for radio equipment
using PMR 446 frequencies as authorized. The use
of this two-way radio product involves the public
airways and its use may be subject to local laws or
r
egulations. Contact your radio licensing authority
f
or more information.
Caring for Your Radio
Your microTALK®radio will give you years of
t
rouble-free service if cared for properly. Here are
a
few suggestions:
• Handle the radio gently.
• Keep it away from dust.
• Never put the radio in water or in a damp place.
• Avoid exposure to extreme temperatures.
Rapid Desktop Charger
and Rechargeable
Batteries
To Insert Batteries in Radio:
1. Remove belt clip by releasing
belt clip latch and sliding clip up.
2. Pull up on lock tab to remove
batter
y cover (on back of
radio).
3. Insert batteries according
to polarity markings.
4. Replace the battery compart-
ment cover and belt clip.
English
Use only the supplied rechargeable batteries
and rapid desktop charger for recharging your
microTALK
®
radio. Non-rechargeable alkaline
batteries can also be used.
Cobra recommends your radio is turned OFF
while being charged.
Radio Power and Volume
To Turn Your Radio ON:
Rotate the ON/OFF Volume knob clockwise to turn
ON your radio and adjust the volume. A series of
tones will indicate the radio is ON.
Your microTALK
®
radio is now in LISTENING MODE,
ready to receive transmissions. The radio is always
in LISTENING MODE, except when the TALK, CALL
or MODE buttons are pressed.
To Turn Your Radio OFF:
– Rotate the ON/OFF Volume
knob counterclockwise past
the click.
Battery Level Meter
The Battery Level Meter will show a Battery icon
containing four bars to indicate the batteries are
fully charged.
When battery power is low, the
Battery Level Meter will show a
blinking Battery icon containing
only one bar to indicate that the
batteries should be recharged or
replaced.
NOTE: Only the supplied NiMH batteries can
be recharged.
Battery/Power Saver
If there are no transmissions
within 10 seconds, the unit will
automatically switch to BATTERY
SAVE MODE and POWER SAVER
will appear in the display. This
will not affect the unit’s ability
to receive incoming transmissions.
Communicating with
Another Person
1.
Press and hold the TALK
button.
2. With the microphone about
5 cm (2 inches) from your
mouth, speak in a normal
voice.
3. Release the button when
you have finished talking
and listen for a response.
You cannot receive incoming
calls while pr
essing the TALK
button.
NOTE: Both radios must be tuned to the same
channel and privacy code to communicate.
R
emove Belt Clip
O
N/OFF Volume
Knob
Lock Tab
Insert Batteries
5 cm (2 Inches)
From Mouth
Talk Button
Low Battery
Power Saver
Printed in China Part No. 480 439 P Version A
Insert Radio(s)
OPERATION
Listening for a Response
Release the TALK button to
receive incoming transmissions.
Your microTALK
®
is always in
LISTENING MODE except when
the TALK, CALL or MODE
b
uttons are pressed.
To Adjust Volume
Rotate the ON/OFF Volume
k
nob clockwise to increase
volume and counterclockwise
to reduce it.
Call Button
Press and release the CALL
button.
The other person will hear a
two (2) second ringing tone.
You cannot receive transmissions
while sending a call.
NOTE: Both radios must be tuned to the same
channel and privacy code to communicate.
English
To Illuminate Display
Press and release the
LIGHT/MAX RANGE button
to illuminate the display for
10 seconds.
Auto Squelch/
Maximum Range Extender
Your microTALK®radio is equipped with Auto
Squelch, which automatically shuts off weak
transmissions and unwanted noise resulting from
terrain, conditions, or from reaching your maximum
r
ange limit.
You can temporarily turn OFF Auto Squelch or turn
ON Maximum Range Extender, allowing all signals
to be received and extending the maximum range
of your radio.
To Temporarily Turn OFF Auto Squelch:
– Press the LIGHT/MAX RANGE button for
less than five (5) seconds.
If you hear two (2) beeps, you have turned the
Maximum Range Extender ON (see below).
To Turn Maximum Range Extender ON:
– Press and hold the LIGHT/MAX RANGE button for
at least five (5) seconds until you hear two (2)
beeps, indicating that the Maximum Range
Extender is ON.
To Turn Maximum Range Extender OFF:
– Pr
ess and release the LIGHT/MAX RANGE button
or change channels.
Channels
With the radio ON, select any of
the 8 channels by pushing the
CHANNEL UP or CHANNEL
DOWN button.
You can press and hold the
CHANNEL UP or CHANNEL
DOWN button for fast advance.
NOTE: Both radios must be
tuned to the same
channel and privacy code
(see “CTCSS Privacy Codes” or
“DCS Privacy Codes”) to communicate.
Lock Function
The LOCK/ENTER button locks the CHANNEL UP,
CHANNEL DOWN, and MODE buttons to prevent
accidental operation.
To Use the Lock Function:
– Press and hold the LOCK/ENTER
button for two (2) seconds to
turn the Lock ON or OFF.
A double beep sound is used
to confir
m your Lock ON or OFF
request. When the radio is in
LOCK MODE, the Lock icon will
be displayed.
microTALK®Range
Your microTALK®radio has a range of up to
12 kilometres (7.5 miles). Your range will vary
depending on terrain and conditions.
In flat, open country, your radio
will operate at maximum range.
Buildings and foliage in the
path of the signal can reduce
the range.
Dense foliage and hilly terrain
will further reduce the signal.
Remember
, you can achieve
maximum range by using
Maximum Range Extender
.
See above for details.
Light/Max Range
Button
Call Button
Lock/Enter Button
Channel Buttons
Channels
Lock Icon
Maximum Range
Reduced Range
Reduced Range
L
istening
O
N/OFF Volume
Knob
OPERATION and
MODE FUNCTIONS
External Speaker/Microphone Jack
Your microTALK®radio can
be fitted with an external
speaker/microphone, freeing
your hands for other tasks.
To Attach the External
Speaker/Microphone:
1. Open the tab on top of the radio.
2. Insert the plug into the jack.
Intercom
With the optional intercom
adapter and two external
speaker/microphone attachments, a single microTALK
®
radio
can be used as an intercom
s
ystem. (Ideal for motor
cyclists.)
Contact your local dealer for
availability and pricing.
English
Privacy Codes
Your microTalk radio incorporates two advanced
coded squelch systems that can help to reduce
interference from other users on any given channel.
CTCSS (Continuous Tone Coded Squelch System)
provides 38 privacy codes and DCS (Digitally Coded
S
quelch) provides 83 privacy codes. This provides a
t
otal of 121 Privacy Codes. Either system can be
used on all channels, but both systems cannot be
used on the same channel at the same time.
NOTE: To successfully communicate using a privacy
c
ode, both the sending and receiving radios
must be tuned to the same channel and to
the same privacy code system (CTCSS or DCS)
and privacy code number. Each channel will
remember the last privacy code system and
number you select.
NOTE: The privacy code 00 is not a privacy code,
but allows all signals to be heard on a channel
that is set to 00 both on the CTCSS and
DCS systems.
CTCSS Privacy Codes
CTCSS (Continuous Tone Coded Squelch System)
is an advanced tone coding system allowing you to
select one of 38 privacy codes to reduce incoming
transmissions from other users on the channel.
NOTE: If you are using a CTCSS privacy code, both
radios must be tuned to the same channel and
CTCSS privacy code to communicate. Each
channel will remember the last privacy code
you selected.
Scrolling Through Mode Functions
By scrolling through the MODE
functions, you will be
able to select or change preferred features of your
microTALK
®
radio. While you are scrolling through
the MODE functions, your radio features will be
displayed in the same predeter
mined or
der.
Whenever the radio is in a MODE function, it will
revert to LISTENING MODE and save the most
recently selected settings if no buttons are
pressed for 15 seconds.
Set CTCSS Privacy Codes
Set DCS Privacy Codes
Set VOX ON/OFF
Set VOX Sensitivity Level
Set Memor
y Locations
Set Channel Scan
Set CTCSS Privacy Code Scan
Set DCS Privacy Code Scan
Set Memor
y Location Scan
Set VibrAlert and/or Call Alert
Set Dual Watch ON/OFF and
Program Dual Watch Location
Set Baby Monitor
Set Call Aler
t T
one Signal
Set Roger Beep ON/OFF
Set Keystroke Tones ON/OFF
To Select a CTCSS Privacy Code:
1. After selecting a channel,
press and release the
MODE button until the
CTCSS icon flashes on the
display. In addition to the
CTCSS icon, either OFF or
the small numbers next to
the channel number will
also flash on the display.
2. If CTCSS and OFF are flashing,
pr
ess the CHANNEL UP or
CHANNEL DOWN button to
exit OFF and proceed to select a privacy code.
Or, if CTCSS and the small numbers next to
the channel number are flashing, press the
CHANNEL UP or CHANNEL DOWN button
to select a privacy code.
3. Choose one of the following:
a. Press the MODE button to enter the new
setting and proceed to other functions.
b. Press the LOCK/ENTER button to enter the
new setting and r
etur
n to LISTENING MODE.
Select Privacy Code
External Speaker/
M
icrophone Jack
CTCSS OFF
I
ntercom
MODE FUNCTIONS
DCS Privacy Codes
DCS (Digital Coded Squelch) is an advanced
digital coding system allowing you to select one of
83 privacy codes to reduce incoming transmissions
from other users on the channel.
NOTE: If you are using a DCS code, both radios must
be tuned to the same channel and DCS privacy
code to communicate. Each channel will
r
emember the last privacy code you selected.
To Select a DCS Privacy Code:
1
. After selecting a channel,
press and release the MODE
button until the DCS icon
flashes on the display. In
addition to the DCS icon,
either OFF or the small
n
umbers next to the channel
number will also flash on
the display
.
2. If the DCS and OFF are
flashing, press the CHANNEL
UP or CHANNEL DOWN button to exit OFF and
proceed to select a privacy code. Or, if DCS and
the small numbers next to the channel number
are flashing, press the CHANNEL UP or CHANNEL
DOWN button to select a privacy code.
3. Choose one of the following:
a. Press the MODE button to enter the new
setting and proceed to other function.
b. Press the LOCK/ENTER button to enter the
new setting and return to LISTENING MODE.
English
3. Choose one of the following:
a. Press the MODE button to enter the new
s
etting and proceed to other functions.
b. Press the LOCK/ENTER button to enter the
new setting and return to LISTENING MODE.
10 Memory Locations
Your microTALK®radio has 10 Memory Locations
for storing your most frequently used channels and
channel/privacy code combinations. These Memory
L
ocations can be selected individually or can be
scanned.
To Program a Memory Location:
1. Press the MODE button until
the Memory icon and the
m
emory location flash on
the display.
2. Press the CHANNEL UP or
CHANNEL DOWN button to
select the memory location (0 through 9).
NOTE: If a location has been programmed before,
its associated channel/privacy code will be
shown on the display.
3. Press the LOCK/ENTER button to enter a new
memory location or edit an already programmed
memory location. The channel numbers will flash
on the display.
4. Press the CHANNEL UP or CHANNEL DOWN
button to select a channel (1 through 8).
Voice Activated Transmit (VOX)
In VOX MODE, your microT
ALK
®
radio can be used
“hands-free,” automatically transmitting when you
speak. You can set the VOX sensitivity level to fit
the volume of your voice and avoid transmissions
triggered by backgr
ound noise.
To Turn VOX MODE ON or OFF:
1. Press the MODE button until
the VOX icon flashes on the
display. The current ON or
OFF setting is displayed.
2. Press the CHANNEL UP or
CHANNEL DOWN button to
turn VOX ON or OFF.
3. Choose one of the following:
a. Press the MODE button to enter the new
setting and proceed to other functions.
b. Press the LOCK/ENTER button to enter the
new setting and return to LISTENING MODE.
To Set the VOX Sensitivity Level:
1. Press the MODE button until
the VOX icon flashes and
the current sensitivity level
is displayed.
The current sensitivity level is
displayed with the letter “L”
and a number 1 to 5, 5 being the most sensitive
level and 1 being the least sensitive level.
2. Press the CHANNEL UP or CHANNEL DOWN
button to change the setting.
5. Press the LOCK/ENTER button, The CTCSS icon
and privacy code numbers will flash on the
display.
6. Choose one of the following:
a.
Pr
ess the CHANNEL UP or CHANNEL DOWN
button to select a CTCSS privacy code
(01 through 38) for the channel.
b. Press the LOCK/ENTER button to switch from
CTCSS to DCS. The DCS icon and privacy code
numbers will flash on the display. The
CHANNEL UP or CHANNEL DOWN button can
then be used to select a DCS privacy code
(01 through 83) for the channel.
NOTE: If “OFF” flashes in place of the privacy code
numbers, a privacy code is already set in the
opposite (CTCSS or DCS) system. Pr
ess the
CHANNEL UP or CHANNEL DOWN button to
cancel the opposite code and select a privacy
code
fr
om the active system for the selected
channel.
7. Choose one of the following:
a.
Pr
ess the LOCK/ENTER button to enter the
channel/privacy code in the selected memory
location. Radio then proceeds to next Memory
location, which will blink.
b. Press the MODE button to enter the
channel/privacy code in the selected memor
y
locations and pr
oceed to other functions on
the channel/privacy code displayed before
you entered MODE functions.
Select VOX
Select VOX
Sensitivity Level
M
emory Icon
Select Privacy Code
DCS OFF
MODE FUNCTIONS
c. Press the TALK button to enter the
channel/privacy code in the selected memory
location and exit MODE functions. Upon
release of the TALK button, the radio will enter
L
ISTENING MODE on the channel/privacy code
j
ust entered.
To Recall a Stored Memory Channel
Location:
1. Press the MODE button until the Memory icon
and the memory location number flash on the
display.
2
. Press the CHANNEL UP or CHANNEL DOWN
button to select a memory location (0 through 9).
NOTE: If a location has been programmed before,
i
ts associated channel/privacy code will be
shown on the display.
3. Press the TALK button to return to LISTENING
MODE on the selected memory location.
NOTE:
A memory location can be reprogrammed
at any time it is displayed and flashing.
Press the LOCK/ENTER button to begin.
While recalling a stored memory location, if you
do not press any buttons for 15 seconds, your radio
will automatically return to LISTENING MODE on the
channel/privacy code displayed before you entered
MODE functions.
To De-Program a Memory Location:
1.
Press the MODE button until the Memory icon
and the memory location flash on the display.
English
Channel Scan
Your microTALK®radio can automatically scan
channels (1 to 8).
NOTE: The radio ignores specific CTCSS or DCS
p
rivacy codes while scanning channels.
To Scan Channels:
1
. Press the MODE button
until the Scan icon and the
channel number flash on
the display.
2
. Press the CHANNEL UP or CHANNEL DOWN
button to begin scanning channels.
The Scan icon will continue to be displayed when
channel scan is ON. Your radio will continue to scan
a
ll channels and stop if an incoming transmission
is detected. Your radio will remain on that channel
for 10 seconds.
During An Incoming Transmission,
You Can Choose From The Following:
a. Press and hold the TALK button to
communicate on that channel. Your radio
will remain on that channel and return to
LISTENING MODE.
b. Press the CHANNEL UP or CHANNEL DOWN
button to resume scanning channels.
If you do not press any button within 10 seconds,
your radio will automatically resume scanning
channels.
2. Press the CHANNEL UP or CHANNEL DOWN button
to select the memory location (0 through 9).
NOTE: If a location has been programmed before,
its associated channel/privacy code will be
shown on the display
.
3. Press the LOCK/ENTER button. The channel
numbers will flash on the display.
4. Press the CHANNEL UP or
CHANNEL DOWN button to
select Channel O.
5.
Choose one of the following:
a. Press the
LOCK/ENTER
button to enter the channel/privacy code in
the selected memor
y location and r
etur
n to
the beginning of memory location options.
b. Press the MODE button to enter the
channel/privacy code in the selected memory
location and proceed to other functions on the
channel/privacy code displayed befor
e you
enter
ed MODE functions.
While de-pr
ogramming a memory location, if you
do not pr
ess any buttons for 15 seconds, your radio
will automatically return to LISTENING MODE on the
channel/privacy code displayed before you entered
MODE functions.
Privacy Code Scan
Your microTALK®radio can automatically scan the
Privacy Codes (either CTCSS 01 through 38 or DCS
01 through 83) within one channel. Only one set
of privacy codes (CTCSS or DCS) can be scanned
at a time.
To Scan Privacy Codes:
1. While in LISTENING MODE,
press the CHANNEL UP or
CHANNEL DOWN button
to choose the channel on
which you wish to scan
privacy codes.
2. Press the MODE button until
either the CTCSS or the DCS
icon appears on the display
and the Scan icon and the
small numbers next to the
channel number flash on the display.
3.
Pr
ess the CHANNEL UP or CHANNEL DOWN
button to begin scanning privacy codes within
the channel you selected.
The Scan icon will continue to be displayed when
privacy code scan is ON. Your radio will continue
to scan privacy codes and stop as an incoming
transmission is detected. Your radio will remain
on that channel/privacy code for 10 seconds.
Select Channel
Select Scan Channels
Channel O
Select Scan Privacy
Codes
MODE FUNCTIONS
While setting privacy code scan, if you do not
press any buttons for 15 seconds your radio will
automatically return to LISTENING MODE on
the channel/privacy code that was displayed
b
efore you entered MODE functions.
During An Incoming Transmission,
You Can Choose From The Following:
a. Press and hold the TALK button to
communicate on that channel/privacy code.
Your radio will remain on that channel/privacy
code and return to LISTENING MODE.
b
. Press the CHANNEL UP or CHANNEL DOWN
button to resume scanning privacy codes.
If you press the TALK button while scanning,
b
ut more than 10 seconds after receiving a
transmission, you will transmit on the privacy
code on which, during scanning, you last received
a transmission.
If you do not press any button within 10 seconds,
your radio will automatically resume scanning
privacy codes.
English
During Memory Location Scan (While
Receiving An Incoming Transmission),
You Can Choose From The Following:
a. Press and hold the TALK button to
communicate on that memory location.
b. Your radio will remain on that memory
location and return to LISTENING MODE.
Press the CHANNEL UP or CHANNEL DOWN
button to resume scanning memory locations.
If you press the TALK button while scanning,
but more than 10 seconds after receiving a
transmission, you will transmit on the memory
location on which, during scanning, you last
received a transmission.
Memory Location Scan
Your microTALK®radio can automatically scan up to
10 programmed Memory Locations.
NOTES: If there are one or fewer memory locations
programmed in your radio, the scan
memory locations option will not be
available. To program at least two memory
locations, see program memory locations.
To Scan Memory Locations:
1. Press the MODE button
until the Scan icon,
Memory icon and the
memory location number
flash on the display.
2. Press the
CHANNEL UP
or CHANNEL DOWN
button to begin scanning memory locations.
The Scan icon and the Memory icon will continue
to be displayed when memory location scan is ON.
Your radio will continue to scan memory locations
and stop if an incoming transmission is detected.
Your radio will remain on that memory location for
10 seconds.
While setting memory location scan, if you do not
press any buttons for 15 seconds, your radio will
automatically return to LISTENING MODE on the
channel/privacy code displayed before your entered
MODE functions.
VibrAlert and Call Alert
Your microTALK®radio can alert you to incoming
signals by sounding an audible call tone, by
vibrating silently or both.
To Change Call Settings:
1. Press the MODE button until
the Call Settings icon flashes
on the display. The current
setting (“01” vibrate + tone,
“02” vibrate only or “00”
tone only) is displayed.
2. Press the CHANNEL UP or
CHANNEL DOWN button to
change the call setting.
3. Choose one of the following:
a.
Pr
ess the
MODE button to
enter the new setting and
pr
oceed to other
functions.
b. Press the LOCK/ENTER
button to enter the new
setting and return to
LISTENING MODE.
Scanning Locations
VibrAlert + Tone
VibrAlert Only
T
one Only
MODE FUNCTIONS
Dual Watch
Dual Watch allows you to simultaneously monitor
any two (2) Dual Watch Locations:
Dual Watch Location 1 – is always the channel/
p
rivacy code displayed before you entered MODE
functions. See “Channels,” “CTCSS Privacy
Codes” and “DCS Privacy Codes” sections for
further details.
D
ual Watch Location 2 – will be stored in the radio.
It can be edited and/or recalled for future
engagements of DUAL WATCH MODE.
To Program or Edit Dual Watch
L
ocation 2 And Engage Dual Watch Mode:
1. Press the MODE button until
the Dual Watch icon and the
channel number flash on the
display.
2. Choose one of the following:
a. Select or edit a channel:
1) Press the CHANNEL UP or CHANNEL DOWN
button to select a channel (1 to 8).
b. Select or edit a channel/privacy code:
1) Press the CHANNEL UP or CHANNEL DOWN
button to select a channel (1 to 8).
2) Press the MODE button to set the channel.
The small numbers next to the channel
number will flash on the display.
3) Press the CHANNEL UP or CHANNEL DOWN
button to select a CTCSS privacy code
(01 to 38) or DCS privacy code (01 to 83).
English
During An Incoming Transmission,
You Can Choose From The Following:
a
. Press and hold the TALK button to
communicate on that Dual Watch Location.
Your radio will remain on that Dual Watch
Location and return to LISTENING MODE.
b
. Press the CHANNEL UP or CHANNEL DOWN
button to resume Dual Watch.
If you press the TALK button while in Dual Watch
and not within 10 seconds of receiving a
t
ransmission, you will transmit on the last
Dual Watch Location on which you received
a transmission. This will return the radio to
LISTENING MODE.
I
f you do not press any button within 10 seconds,
your radio will automatically resume Dual Watch.
To Terminate Dual Watch:
Choose one of the following:
a. Press the LOCK/ENTER button to return to
LISTENING MODE on either Dual Watch
Location 1 or the last Dual Watch Location
on which, during Dual W
atch, you last
received a transmission.
b. Press the TALK button to return to
LISTENING MODE on either Dual Watch
Location 1 or the last Dual Watch Location
on which, during Dual Watch, you last
received a transmission.
c. Press the MODE button and proceed to the
next available MODE function.
3. Press the LOCK/ENTER button
to set Dual Watch Location 2
and engage DUAL WATCH
MODE (see below for further
details).
NOTES: To terminate Dual Watch and proceed to the
next available MODE function, press the
MODE button.
While setting Dual Watch Location 2, if you
do not press any buttons for 15 seconds
your radio will automatically return to
LISTENING MODE on Dual W
atch Location 1.
To Turn Dual Watch ON:
NOTE: Dual Watch Location 2 must be programmed
to turn Dual Watch ON.
1.
Set the first Dual Watch
Location (channel/privacy
code) you wish to monitor
(see “Channels,” “CTCSS
Privacy Codes” and “DCS
Privacy Codes” sections for
fur
ther details).
2. Press the MODE button until the Dual Watch icon
and the channel number flash on the display.
NOTE: While setting Dual Watch, if you do not press
any buttons for 15 seconds your radio will
automatically return to LISTENING MODE on
the last channel or channel/privacy code
displayed before you entered MODE functions.
3. Press the LOCK/ENTER button to engage
DUAL WATCH MODE.
Lock/Enter Button
S
elect Dual Watch
Select Channel
Baby Monitor
With the Baby Monitor Function ON, a radio left
near a baby will transmit to another unit on the
same channel and privacy code whenever a sound
is detected. Baby Monitor uses the same
sensitivity level you set for the VOX Function.
I
f you have not set a VOX sensitivity level
(
see the “Voice Activated Transmit [VOX]” section
of this manual), the maximum sensitivity, level 5,
will automatically be used.
To Turn Baby Monitor ON:
1. Press MODE button until the
Baby Monitor icon flashes on
the display. The current OFF
setting is displayed.
2.Press the CHANNEL UP or
CHANNEL DOWN button to change
the setting to ON.
3. Press the LOCK/ENTER button to enter the
ON setting and enter BABY MONITOR MODE.
NOTES: Pressing the MODE button will enter the
BABY MONITOR MODE setting as OFF and
proceed to other MODE functions.
Not pressing any buttons for 15 seconds
will enter the BABY MONITOR MODE
setting as OFF and return the radio to
LISTENING MODE.
NOTE: Both radios must be tuned to the same
channel and privacy code to communicate.
10 Call Tone Settings
Y
ou can choose between 10 different call tone
s
ettings to transmit a unique call alert.
To Change a Call Tone Setting:
1
. Press the MODE button
until the letter “C” and the
current call tone number
(1 to 10) is displayed. The
current call tone will sound
for two (2) seconds.
2. Press the CHANNEL UP or CHANNEL DOWN
button to hear the other call tone settings.
3
. Choose one of the following:
a. Press the MODE button to enter the new
setting and proceed to other functions.
b. Press the LOCK/ENTER button to enter the
new setting and return to LISTENING MODE.
To Terminate Baby Monitor Mode:
Choose one of the following:
a. Press the TALK button and return to
LISTENING MODE.
b. Press the LOCK/ENTER button and return to
LISTENING MODE.
c. Press the MODE button and proceed to
the next available MODE function.
"Roger Beep" Confirmation Tone
Your listener will hear an audible tone when
you release the TALK button. This alerts the other
party that you have finished talking and that it is
OK for them to speak. This feature can be turned
ON or OFF.
To Turn “Roger Beep” ON or OFF:
When you turn ON your microTALK®radio for
the first time, “Roger Beep” will be ON.
1. Press and release the MODE
button until the “Roger
Beep” icon flashes on the
display. The current ON or
OFF setting is displayed.
2. Press the CHANNEL UP or CHANNEL DOWN
button to select “Roger Beep” ON or OFF.
3. Choose one of the following:
a. Press the MODE button to enter the new
setting and proceed to other functions.
b. Press the LOCK/ENTER button to enter the
new setting and return to LISTENING MODE.
The setting you select will be saved when you
turn your radio OFF and ON again. When the
“Roger Beep” is ON, the “Roger Beep” icon
will be displayed.
MODE FUNCTIONS
English
Call Tone Setting
Select Roger Beep
S
elect Baby Monitor
English
D.O.C., WARRANTY
& CUSTOMER SERVICE
Keystroke Tones
W
ith Keystroke Tones turned ON, your radio will
sound beeps each time you press a button or
change a setting.
To Turn Keystroke Tones ON or OFF:
When you turn ON your microTALK®radio for
the first time, Keystroke Tones will be ON.
1
. Press the MODE button until
the Keystroke Tones icon
flashes on the display. The
current ON or OFF setting is
displayed.
2. Press the CHANNEL UP or
CHANNEL DOWN button to turn
Keystroke Tones ON or OFF.
3. Choose one of the following:
a. Press the MODE button to enter the new
s
etting and return to LISTENING MODE.
b. Press the LOCK/ENTER button to enter the
new setting and return to LISTENING MODE.
The setting you select will be saved when you turn
your radio OFF and ON again. When Keystroke
Tones are ON, the Keystroke Tone icon will be
displayed.
English
MODE FUNCTIONS
Select Keystroke
THIS PAGE TO INCLUDE
D.O.C., WARRANTY & CUSTOMER SER
VICE
INFORMATION WHEN COMPLETE.
Loading...