microSYST miline FTL10 Operating Manual

microSYST Systemelectronic GmbH, Am Gewerbepark 11, 92670 Windischeschenbach
 [phone],  [phone], [e-mail], www.microsyst.de

miline FTL10

LED Multifunction Clock

Operating Manual

miline FTL10

LED Multifunction Clock

Page 2

microSYST Systemelectronic GmbH, Am Gewerbepark 11, 92670 Windischeschenbach
 [phone],  [phone], [e-mail], www.microsyst.de

Index

1 SAFETY INSTRUCTIONS 3

2 SCOPE OF DELIVERY 3

3 MOUNTING 4

4 BRIEF DESCRIPTION 5

5 START-UP 6

6 OPERATING MODE 7

7 CONFIGURATION 8

7.1 Display Settings 9

7.2 Channel Setting Multifunction Sensor (optional) 10

7.3 DCF Setting (optional) 10

8 DECLARATION OF CONFORMITY 11

9 GUARANTEE 12

10 TECHNICAL DATA 13

11 DIMENSIONS 15

miline FTL10

LED Multifunction Clock

Page 3

microSYST Systemelectronic GmbH, Am Gewerbepark 11, 92670 Windischeschenbach
 [phone],  [phone], [e-mail], www.microsyst.de

1 Safety Instructions

Please read these instructions carefully and follow all instructions and safety infor­mation. Non-observance could result in injury to persons and / or damage the unit.

Use only the included AC adapter. Check for tight fit in the socket. Wobbly
plugs or receptacle may cause a fire. If you want to disconnect power, do not
unplug the cord, but disconnect the AC adapter.

Connect the display to an easily accessible power outlet (230 V / 50 Hz), which is
located near the installation site.

Do not touch the plug contacts with metallic, sharp or wet objects.
Please do not open the housing of the display. Refer servicing to an expert, as this

usually leads to the loss of your warranty claims.
Protect the display from moisture, water, steam and aggressive fluids!
Do not install near strong magnetic fields. The reception may be impaired.

2 Scope of Delivery

Please check the product’s package for completeness:
Standard:

 Multifunction clock including angle bracket
 AC adapter
 Remote control
 Batteries for the remote control

Option:

 Multifunction Sensor
 Batteries for the multifunction sensor

miline FTL10

LED Multifunction Clock

Page 4

microSYST Systemelectronic GmbH, Am Gewerbepark 11, 92670 Windischeschenbach
 [phone],  [phone], [e-mail], www.microsyst.de

3 Mounting

LED Multifunction Clock “miline FTL10”

The adjustable bracket on the back allows wall or ceiling mounting.
Examples:

Multifunction Sensor “MFS10” (optional)

The integrated antenna must be in horizontal position for DCF77-reception. Please
regard for a correct position in case of wall mounting.
The sensor is always horizontal, if it’s mounted on the ceiling.

Example:

Antenna

miline FTL10

LED Multifunction Clock

Page 5

microSYST Systemelectronic GmbH, Am Gewerbepark 11, 92670 Windischeschenbach
 [phone],  [phone], [e-mail], www.microsyst.de

4 Brief Description

The "miline FTL10" display with 120 mm character height and white LEDs is de­signed for use in indoor and semi-outdoor areas. The standard version of this
display alternately shows time and date (user adjustable, based on quartz) in an
adjustable change interval from 1 to 30 seconds.

Optionally, the standard model can be upgraded to a multi-function display. An
external wireless sensor “MFS10” provides DCF77 radio clock, temperature and
humidity sensor.

The implemented LED dot matrix technology and automatic brightness adjust­ment to the ambient light serve for a readability up to an angle of ±60°.

A variable wall bracket on the back of the anodised aluminium profile housing al­lows both wall and ceiling mount.

In case of power failure, the internal battery is able to save time and date up to
10 years. Settings on the display are done with the included remote control.

Remote Control
for Configuration

Multifunction Sensor
“MFS10“ (optional)

IR

433 Mhz

LED Multifunction Clock “miline FTL10“

miline FTL10

LED Multifunction Clock

Page 6

microSYST Systemelectronic GmbH, Am Gewerbepark 11, 92670 Windischeschenbach
 [phone],  [phone], [e-mail], www.microsyst.de

5 Start-Up

Display without Multifunction Sensor

 Plug the AC adapter.
 Open the remote control and insert the batteries.
 Set time and date (see chapter “Configuration“).

Display with Multifunction Sensor

 Plug the AC adapter.
 Open the remote control and insert the batteries.
 Open the multifunction sensor and insert the batteries. At this, the green function

LED will flash up for one second.

 Regarding the synchronisation settings, see chapter "Configuration".

miline FTL10

LED Multifunction Clock

Page 7

microSYST Systemelectronic GmbH, Am Gewerbepark 11, 92670 Windischeschenbach
 [phone],  [phone], [e-mail], www.microsyst.de

6 Operating Mode

According to expansion stage, the display shows the following measures:

Time

Date

Temperature (optional, with “MFS10”)

Relative humidity (optional, with “MFS10”)

Low Battery:

If the batteries in the sensor "MFS10" are too low, the display shows a
battery icon instead of temperature and humidity level.

miline FTL10

LED Multifunction Clock

Page 8

microSYST Systemelectronic GmbH, Am Gewerbepark 11, 92670 Windischeschenbach
 [phone],  [phone], [e-mail], www.microsyst.de

7 Configuration

The display is configured with the included universal remote control.

Button

Function

On-off switch for the display

Setup mode

VOLUME +/-

Digit selection (date / time)
and menu navigation

CHANNEL +/-

Value adjustment

miline FTL10

LED Multifunction Clock

Page 9

microSYST Systemelectronic GmbH, Am Gewerbepark 11, 92670 Windischeschenbach
 [phone],  [phone], [e-mail], www.microsyst.de

7.1 Display Settings

Press button for 2 seconds until the display’s hour digit starts to flash, then use the
navigation keys to select the desired menu item. The values can be changed with the
corresponding buttons.

Menu Navigation (button “VOLUME +“):

Hours

Time setting
For systems with multi-function sensor,
DCF77 defaults always take precedence.

Minutes

Day

Date setting
For systems with multi-function sensor,
DCF77 defaults always take precedence.

Month

P1 - Display time

Appearance of the single measures:
00: deactivated

01: activated
Standard without „MFS10“: P1 + P2 = 01

P3 + P4 = 00
Standard with „MFS10“: P1...P4 = 01

P2 - Display date

P3 - Display temperature
(optional with “MFS10”)

P4 - Display humidity
(optional with “MFS10”)

P5 - Alternation interval

Time for displaying a measure.
Setting range: 01 to 30 seconds
Standard: 05

P6 - Maximum brightness

This menu item is shown with the current maxi­mum brightness.
Setting range: 01 to 99
Standard: 99

P7 - Flashing colon (at the time)

Setting range: 00 / 01
00: deactivated
01: activated
Standard: 01

P8 - Radio channel

Selection of the radio channel
Setting range: 01 to 06
Standard: 01

P9 - Request DCF77 reception

DCF77 status
(description see next page)

The settings are saved with the button . After that, setup mode is left.

miline FTL10

LED Multifunction Clock

Page 10

microSYST Systemelectronic GmbH, Am Gewerbepark 11, 92670 Windischeschenbach
 [phone],  [phone], [e-mail], www.microsyst.de

7.2 Channel Setting Multifunction Sensor (optional)

6 radio channels are provided for communication between the sensor and display.
This allows the operation of up to 6 display systems in the same transmission range.

It may be necessary to synchronize the multifunction sensor with the display.

Please proceed as follows:

 Select desired radio channel (01 to 06) with display’s menu item P8.
 Open the multi-function light sensor and press the button on the board about 1

second until the green LED is lit.

 After synchronisation, this LED goes off and the display will quit setup mode

automatically.

 After 20 seconds at the earliest, current data are shown.

7.3 DCF Setting (optional)

You can force an attempt for DCF77 reception with menu item P9 to find the optimal
position for the multifunction sensor.
Please stay in this menu and observe the status message. If the reception is suffi­cient, you get the following sequence (within max. 5 minutes):

Status message

Meaning

0

Attempt for reception started

1

DCF signal identified

2

Data reception

3

Time and date have been updated

The DCF signal is not sufficient, if the status message changes between “1” and “2”.

At status “0”, no reception is possible.

miline FTL10

LED Multifunction Clock

Page 11

microSYST Systemelectronic GmbH, Am Gewerbepark 11, 92670 Windischeschenbach
 [phone],  [phone], [e-mail], www.microsyst.de

8 Declaration of Conformity

EU-Konformitätserklärung

EU Declaration of Conformity

Produktbezeichnung: miline

Product name:

Typenreihe: miline FTL 10

Type code:

Hersteller: microSYST Systemelectronic GmbH

Manufacturer: Am Gewerbepark 11
92670 Windischeschenbach

Das bezeichnete Produkt stimmt mit
der folgenden Europäischen Richtlinie
überein:

We herewith confirm that the above men­tioned product meets the requirements of
the following standard:

Die Übereinstimmung des bezeichneten Produk­tes mit den Vorschriften der angewandten Richt­linie(n) wird nachgewiesen durch die Einhaltung
folgender Normen / Vorschriften:

The conformity of the product described above with
the provisions of the applied Directive(s) is demon­strated by compliance with the following standards /
regulations:

Richtlinien / Directives

Europäische Norm / Standard

EMV Richtlinie

EMC Directive

2014/30/EU

EN61000-6-2:2005

EN61000-6-3:2007 +A1:2011

RoHS Richtlinie

RoHS Directive

2011/65/EU

EN50581:2012

Windischeschenbach, 11.12.2017

Manuel Raß
Geschäftsführer / General Manager

miline FTL10

LED Multifunction Clock

Page 12

microSYST Systemelectronic GmbH, Am Gewerbepark 11, 92670 Windischeschenbach
 [phone],  [phone], [e-mail], www.microsyst.de

9 Guarantee

The display is guaranteed for the duration specified in the “General

Terms and Conditions” regarding manufactured products and services

rendered for the electrical industry against defects which existed at the
time the device was delivered to the buyer.

The device is subject to technical change without notice. Errors and
omissions are accepted. No claims can be honored for the shipment of
a new product. The buyer is required to make notification of defects
within 2 weeks after identification of such. Non-observance of notifica­tion requirements is equated with acceptance of the defect.

Defects and their symptoms must be described as accurately as possi­ble in order to allow for reproducibility and elimination. The buyer must
provide for access to all required and/or useful information regarding de­fects at no charge, as well as to the affected devices, and must make all
of the required data and machine time available free of charge.

The guarantee does not cover defects, which result from non­observance of the prescribed conditions of use, or from improper han­dling.

If the device has been placed at the disposal of the buyer for test pur­poses and has been purchased subsequent to such testing, both parties

agree that the product is to be considered “used” and that it has been

purchased “as is”. No guarantee claims may be made in such cases.

The “General Terms and Conditions” regarding manufactured products

and services rendered for the electrical industry apply as well.

miline FTL10

LED Multifunction Clock

Page 13

microSYST Systemelectronic GmbH, Am Gewerbepark 11, 92670 Windischeschenbach
 [phone],  [phone], [e-mail], www.microsyst.de

10 Technical Data

LED Multifunction Clock “miline FTL10”

Display type: LED dot matrix
Application range: indoor and semi-outdoor (without direct solar radiation)
Angle of radiation: ±60°
Character height: 120 mm
Reading distance: up to approx. 50 m
Display colour: white
Light intensity: > 2000 cd/sqm
Brightness control: automatically; maximum value manually adjustable
View: single-sided
Display: time: hours + minutes, date: day + month;
With optional multifunction sensor:
temperature: -40 to +60 °C; humidity: h 01 to 99 %
Clock preciseness: ±1 min. / year from 0 to +40 °C ambient temperature;
DCF-exact (“radio controlled clock“) via optional multifunction sensor
Interfaces: IR interface; 433 MHz radio interface (6 channels)
Operating voltage: 15 to 40 VDC; 230 VAC via external power supply plug
Power consumption: approx. 10 W
Housing: anodised aluminium
Housing dimensions: see next chapter
Housing colour: black
Mounting: wall or ceiling mounting; inclination adjustable
Protection: IP54
Operating temperature: -20 to +60 °C
Storage temperature: -25 to +70 °C
Equipment: multifunction sensor “MFS10“

Multifunction Sensor “MFS10”

Interface: 433 MHz radio interface (6 channels)
Sensors: temperature sensor; humidity sensor
Aerial: DCF77-reception (“radio controlled clock”)
Features: temperature measurement; humidity measurement;
2 x a day DCF77-reception;
communication to “miline FTL10“ via radio (433 MHz)
Number of displays
per multifunction sensor: 10 pieces with parallel operation
Range: max. 50 m, depending on ambient conditions
Operating voltage: 3 VDC (via 2 x batteries AA)
Housing: plastic
Housing dimensions: see next chapter
Housing colour: grey
Mounting: wall or ceiling mounting
Protection: IP65
Operating temperature: -40 to +60 °C
Storage temperature: -40 to +60 °C

miline FTL10

LED Multifunction Clock

Page 14

microSYST Systemelectronic GmbH, Am Gewerbepark 11, 92670 Windischeschenbach
 [phone],  [phone], [e-mail], www.microsyst.de

Maximum T-tolerance

Maximum RH-tolerance (at 25 °C)

ΔT (°C)

Temperature °C

ΔRH (%RH)

Relative Humidity (%RH)

miline FTL10

LED Multifunction Clock

Page 15

microSYST Systemelectronic GmbH, Am Gewerbepark 11, 92670 Windischeschenbach
 [phone],  [phone], [e-mail], www.microsyst.de

11 Dimensions

LED Multifunction Clock “miline FTL10”

Multifunction Sensor “MFS10”