Micro Star Co MS6855B Users Manual

MP54GBT2 (MS-6855B) Wireless 11g + Bluetooth

Combo MiniPCI Card

OEM Guide

FCC Caution

1. The device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

2. FCC RF Radiation Exposure Statement: The equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.

3. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

4. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment.

FCC Statement

This device is intended only for OEM integrators under the following

1) The antenna must be installed such that 20 cm is maintained between antenna

and users, and

2) The transmitter module may not be co-located with any other transmitter or

antenna.

As long as 2 conditions above are met, further transmitter test will not required. However, the OEM integrator is still responsible for testing end-product for any additional compliance requirements required with module installed (for example, digital device emissions, PC peripheral requirements, etc.).

Important Note

In the event that these conditions can not be example certain laptop configurations or colocation with another transmitter), then the FCC authorization is no longer considered valid the FCC ID can not be used on the final product. In these circumstances, OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

End Product Labeling

This transmitter module is authorized only for use in device where antenna may be installed such that 20 cm may be maintained between antenna and users (for example access points, routers, wireless ADSL and similar equipment). The final end product must be labeled in a area with the following: “ Contains TX FCC ID: I4L-MS6855B”.

Manual Information for End Users

The end user must not have manual instructions to remove or install device. The user manual for end users must include the following information in a prominent location: “IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located operating in conjunction with any other antenna or transmitter.” as a result of e-mail transmission.”

Important Safety Precautions

Always read and follow these basic safety precautions carefully when handling any piece of electronic component.

1. Keep this OEM Guide for future reference.

2. Keep this equipment away from humidity.

3. Lay this equipment on a reliable flat surface before setting it up.

4. The openings on the enclosure are for air convection hence protects the equipment from overheating.

5. All cautions and warnings on the equipment should be noted.

6. Never pour any liquid into the opening that could damage or cause electrical shock.

7. If any of the following situations arises, get the equipment checked by a service personnel:

Liquid has penetrated into the equipment The equipment has been exposed to moisture The equipment has not work well or you can not get it work

according to OEM Manual

The equipment has dropped and damaged If the equipment has obvious sign of breakage

8. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT UNCONDITIONED, STORAGE TEMPERATURE ABOVE 60O C OR BELOW -20OC, IT MAY DAMAGE THE EQUIPMENT.

iii

“FCC RF exposure requirements: SAR compliance has been established in the laptop computer(s)

configurations as documented in this OEM Installation Manual, and can be used in laptop computer(s)

with substantially similar physical dimensions, construction, and electrical and RF characteristics.

Use in other devices such a PDAs or lappads is not authorized. This transmitter is restricted for use

with the specific antenna(s) tested in the application for Certification. The antenna(s) used for this

transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.”

Introduction

>>> 1.1 MP54GBT2 (MS-6855B) - Wireless 11g +

Bluetooth Combo MiniPCI Card

MSI MP54GBT2, the Wireless 11g + Bluetooth Combo miniPCI Card, is a Type IIIB card, which can be used to integrate with such systems as notebook, mini-barebone, PDA, portable PC. With MSI MP54GBT2 embedded inside, a system could provide users with the ability and flexibility to connect up to Internet wirelessly via 802.11g with speed up to 54Mbps, and to link with peripherals wirelessly through BluetoothTM v2.0 and advanced EDR (Enhanced Data Rate) technology. Bluetooth v2.0 technology increases the data rate of BluetoothTM v1.1/1.2 from 1.0Mbps to 2.1Mbps.

MSI MP54GBT2 is taking advantage of leading technologies from Ralink and CSR. It addresses the co-existence issues in PAN (Personal Area Network) and WLAN (Wireless Local Area Network) markets by providing true simultaneous connectivity while deploying IEEE 802.11g and Bluetooth v2.0 Along with this combo solution, a system installed with a single card is able to offer dual mode capability of WiFi and BluetoothTM. It will benefit system vendors in miniaturization of system dimension and BOM cost reduction, as well as also make users happy with the all-in-one functionality.

>>> 1.2 How MP54GBT2 Works

In WLAN Environment1.2.1 Ad-hoc Mode : An Ad-hoc network is a local area network or

other small network, especially one with wireless or temporary plug-in connections, in which some of the network devices are part of the network only for the duration of a communications session. Users in the network can share files, print to a shared printer, and access the Internet with a shared modem. In this kind of network, new devices can be quickly added; however, users can only communicate with other wireless LAN computers that are in this wireless LAN workgroup, and are within range.

MP54GBT2