Microsonic lcs+600/DD Operating Manual

Set switched output

Further Settings

Sensor adjustment with Teach-in procedure

Adjust detect

point D1-

method A

Place object at

position 1.

Press T1 for about
3 s until both LEDs

flash simultaneously

.

Both

LEDs:

flash
mutually

Press T1 for about

1 s.

Adjust detect

point + 8 % D1 -

method B

Place object at

position 1.

Press T1 for about
3 s until both LEDs

flash simultaneously

.

Both

LEDs:

Press T1 for about
3 s until both LEDs

flash mutually

again.

flash
mutually

Adjust window

mode D1

Place object at

position 1.

Adjust two-way

reflective barrier D1

Place reflector at

position 1.

Set NOC/NCC D1

Press T1 for about
3 s until both LEDs

flash simultaneously

.

Press T1 for about

3 s until both LEDs

flash simultaneously

.

Both

LEDs:

Place object at

position 2.

flash
mutually

Both

LEDs:

Press T1 for about

1 s.

flash
mutually

Both

LEDs:

Press T1 for about

10 s until both LEDs

stop

flashing.

Press T1 for about

13 s until both LEDs

flash mutually

.

flash
mutually

LED D2:
LED D1:

flashes

on: NOC/
off: NCC

To change output

characteristic press T1

for about 1 s.

Adjust detect

point D2 ­method A

Place object at

position 1.

Adjust detect

point + 8 % D2-

method B

Place object at

position 1.

Press T2 for about

3 s until both LEDs

flash simultaneously

.

Both

LEDs:

flash
mutually

Press T2 for about

1 s.

Press T2 for about

3 s until both LEDs

flash simultaneously

.

Both

LEDs:

Press T2 for about

3 s until both LEDs

flash mutually

again.

flash
mutually

Adjust window

mode D2

Place object at

position 1.

Adjust two-way

reflective barrier D2

Place reflector at

position 1.

Set NOC/NCC D2

Press T2 for about

3 s until both LEDs

flash simultaneously

.

Press T2 for about

3 s until both LEDs

flash simultaneously

.

Both

LEDs:

Place object at positi-

on 2.

flash
mutually

Both

LEDs:

Press T2 for about

1 s.

flash
mutually

Both

LEDs:

Press T2 for about

10 s until both LEDs

stop

flashing.

Press T2 for about

13 s until both LEDs

flash mutually

.

flash
mutually

LED D1:
LED D2:

flashes

on: NOC/
off: NCC

To change output

characteristic press T2

for about 1 s.

Normal mode operation

Wait for 10 s.

Normal mode operation

Wait for 10 s.

Activate/deactivate

Teach-in

Turn supply voltage

OFF.

Reset to factory

setting

Turn supply voltage

OFF.

While pressing T1

turn supply voltage

ON.

Press T1 for about

3 s until both LEDs

flash simultaneously

.

LED D2:

LED D1:

flashes

on: Teach-in
activated
off: Teach-in
deactivated

To activate or deacti-

vate Teach-in press T1

for about 1 s.

While pressing T1

turn supply voltage

ON.

Press T1 for about

13 s until both LEDs

flash mutually

.

Wait for 10 s.

Normal mode operation

Operating manual

Ultrasonic proximity switch with
two switched outputs

lcs+340/DD
lcs+600/DD

Product description

The lcs+ sensor offers a non-contact
measurement of the distance to an
object which must be positioned within
the sensor’s detection zone. The swit­ched outputs are set conditional upon
the adjusted detect distances.
Via the Teach-in procedure, the detect
distances and operating modes can
be adjusted. Two LEDs indicate opera­tion and the state of the switched
outputs.
Optionally all Teach-in and additional
sensor parameter settings can be
made using the LinkControl Adapter
LCA-2 (optional accessory) and the
LinkControl software for windows.

Safety instructions

 Read the operating instructions

prior to start-up.

 Connection, installation and ad-

justments may only be carried out
by qualified staff.



No safety component in accordance
with the EU Machine Directive.

Use for intended purpose only

lcs+ultrasonic sensors are used for
non-contact detection of objects.

Installation

 Mount the sensor at the place of

fitting.

 Connect a connection cable to the

M12 device plug.

Start-up

 Connect the power supply.
 Carry out sensor adjustment in

accordance with the diagram.

Fig. 1: Pin assignment with view onto sensor

plug and colour coding of the
microsonic connection cables

Factory setting

 Switched output on NOC.
 Detect distance at operating range

and half operating range.

1
3

colour

+U

B

-U

B

brown

blue
4
2
5

D2D1black

white

Sync/Com grey

1

5

2

34

Synchronisation

If under multiple sensor operation
the assembly distance falls below the
values shown in Fig. 2, the internal
synchronisation should be used. For
this purpose interconnect each pin 5
of max. 10 sensors.

Fig. 2: Assembly distances

Maintenance

microsonic sensors are maintenance­free. In case of excess caked-on dirt
we recommend cleaning the white
sensor surface

≥ 2.00 m

≥ 4.00 m

≥ 18.00 m

≥ 30.00 m

Notes

 The sensors of the lcs+ family have

a blind zone, within which a dis­tance measurement is not possi­ble.

 The lcs+ sensors are equipped

with an internal temperature com­pensation. Due to the sensor's self
heating, the temperature compen­sation reaches its optimum work­ing-point after approx. 30 minutes
of operation.

 During normal operation a yellow

LED signals that the corresponding
output has connected.

 If no push-buttons are pressed for

20 seconds during parameter set­ting mode the made changes are
stored and the sensor returns to
normal mode operation.

Set switched output D1

Further settings

Set switched output D2

Technical data

blind zone

operating range

maximum range

angle of beam spread

0 to 350 mm
3,400 mm

0 to 600 mm

6,000 mm
5,000 mm
see »detection zones«

8,000 mm

see »detection zones«

transducer frequency

resolution

reproducibility

detection zones

for different objects:

The dark grey areas represent the zone

where it is easy to recognise the normal

reflector (round bar). This indicates the typical

operating range of the sensors. The light

grey areas represent the zone where a

good reflector – for instance a

plate – can still be regognised. The

requirement here is for an optimum

alignment to the sensor. It is not

possible to evaluate ultrasonic

reflections outside this area.

ca. 120 kHz

0.18 mm

ca. 80 kHz

0.18 mm

± 0.15 %

± 0.15 %

accuracy

operating voltage U

B

±1 % (temperature drift internally compensated; may

be deactivated, 0.17 %/K without compensation)

±1 % (temperature drift internally compensated; may

be deactivated, 0.17 %/K without compensation)
9 V to 30 V DC, Class 2
reverse polarity protection

9 V to 30 V DC, Class 2

reverse polarity protection

voltage ripple

no-load current consumption

housing

±10 %

≤ 60 mA

±10 %

≤ 60 mA

PBT, Polyester; ultrasonic transducer:
polyurethane foam, epoxy resin with glass content

PBT, Polyester; ultrasonic transducer:

polyurethane foam, epoxy resin with glass content

class of protection per EN 60 529

type of connection

controls

programmable

IP 67
5-pin M12 circular plug, PBT

IP 67

5-pin M12 circular plug,. PBT
2 push-buttons

• Teach-in via push-buttons

2 push-buttons

• Teach-in via push-buttons

indicators

synchronisation

operating temperature

• LCA-2 with LinkControl
2 LEDs yellow/green (switched output set/not set)

• LCA-2 with LinkControl

2 LEDs yellow/green (switched output set/not set)
internal synchronisation up to 10 sensors

-25°C to +70°C

internal synchronisation up to 10 sensors

-25°C to +70°C

storage temperature

weight

switching hysteresis

1)

switching frequency

1)

-40°C to +85°C
180 g

-40°C to +85°C

240 g
50 mm
4 Hz

100 mm

3 Hz

response time

1)

time delay before availability

1)

norm conformity

172 ms
< 380 ms

240 ms

< 450 ms
EN 60947-5-2 EN 60947-5-2

order no.

switched output

1) Can be programmed with LinkControl

lcs+340/DD

2 x pnp, UB-2 V, I

max

= 2 x 200 mA

lcs+600/DD

2 x pnp, UB-2 V, I

max

= 2 x 200 mA

NOC/NCC adjustable, short-circuit-proof NOC/NCC adjustable, short-circuit-proof

+U

B

-U

B

D1
D2
Sync/Com

1
2
4
5
3

2 pnp switched outputs

U

lcs+340…

lcs+600…

0 m

0.8 m

1.6 m

2.4 m

3.2 m

4 m

4.8 m

5.6 m

3.4 m

Plate

Round bar ø 27 mm

1.6 m

0.8 m

0 m

0.8 m

1.6 m
0 m

1.2 m

2.4 m

3.6 m

4.8 m

6 m

7.2 m

8.4 m

Plate

Round bar ø 27 mm

2.4 m

1.2 m

0 m

1.2 m

2.4 m

MV-DO-121024-464442

microsonic GmbH / Phoenixseestraße 7 / 44263 Dortmund / Germany / T [phone] / F [phone] / E [e-mail] / W microsonic.de

The content of this document is subject to technical changes. Specifications in this document are presented in a descriptive way only. They do not confirm any product features.

2004/108/EC

Enclosure Type 1

For use only in industrial

machinery NFPA 79 applications.

 In the »Two-way reflective barrier«

operating mode, the object has to
be within the range of 0-85 % of
the set distance.

 In the Teach-in procedure »Set de-

tect point – method A« the actual
distance to the object is taught to
the sensor as the detect point. If
the object moves towards the
sensor (e.g. with level control) then
the taught distance is the level at
which the sensor has to switch the
output.

 If the object to be scanned moves

into the detection area from the
side, the Teach-in procedure »Set
detect point +8 % – method B«
should be used. In this way the
switching distance is set 8 % fur­ther than the actual measured dis­tance to the object. This ensures a
reliable switching distance even if
the height of the objects varies
slightly.

Fig. 3: Setting the detect point for different

directions of movement of the object



The sensor can be reset to its fac­tory setting (see »Sensor adjust­ment with Teach-in procedure«).

 Optionally all Teach-in and addi-

tional sensor parameter settings
can be made using the LinkCon­trol adapter (optional accessory)
and the LinkControl software for
windows.

Enclosure Type 1

For use only in industrial

machinery NFPA 79 applications.