Microsoft RM-76 User Manual

User guide Nokia 6101
RM-76
Issue 1 EU (FCC)
DECLARATION OF CONFORMITY We, NOKIA CORPORATION declare under our sole responsibility that the product RM-76 is in conformity with the provisions of the following Council Directive: 1999/5/EC. A copy of the Declaration of Conformity can be found from http://www.nokia.com/phones/declaration_of_conformity/.
Copyright © 2005 Nokia. All rights reserved.
Reproduction, transfer, distribution or storage of part or all of the contents in this document in any form without the prior written permission of Nokia is prohibited.
Nokia, Nokia Connecting People, Xpress-on and Pop-Port are trademarks or registered trademarks of Nokia Corporation. Other product and company names mentioned herein may be trademarks or tradenames of their respective owners.
Nokia tune is a sound mark of Nokia Corporation.
US Patent No 5 818437 and other pending patents. T9 text input software Copyright (C) 1997-2005. Tegic Communications, Inc. All rights rese rved.
Includes RSA BSAFE cryptographic or security protocol software from RSA Security.
Java is a trademark of Sun Microsystems, Inc.
Nokia operates a policy of continuous development. Nokia reserves the right to make changes and improvements to any of the products described in this document without prior notice.
Under no circumstances shall Nokia be responsible for any loss of data or income or any special, incidental, consequential or indirect damages howsoever caused.
The contents of this document are provided "as is". Except as required by applicable law, no warranties of any kind, either express or implied, including, but not limited to, the implied warranties o f merchantability an d fitness for a partic ular purpose, are mad e in relation to the accuracy, reliability or contents of this document. Nokia reserves the right to revise this document or withdraw it at any time without prior notice.
The availability of particular products may vary by region. Please check with the Nokia dealer nearest to you.
This device may contain commodities, technology or software subject to export laws and regulations from the US and other countries. D iversion contrary to law is prohibited.
XXXXXXX/Issue 1
UNDER NO CIRCUMSTANCES SHALL NOKIA BE RESPONSIBLE FOR ANY LOSS OF DATA OR INCOME OR ANY SPECIAL, INCIDENTAL, AND CONSEQUENTIAL OR INDIRECT DAMAGES HOWSOEVER CAUSED. THE CONTENTS OF THIS DOCUMENT ARE PROVIDED "AS IS." EXCEPT AS REQUIRED BY APPLICABLE LAW, NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE MADE IN RELATION TO THE ACCURACY AND RELIABILITY OR CONTENTS OF THIS DOCUMENT. NOKIA RESERVES THE RIGHT TOREVISE THIS DOCUMENT OR WITHDRAW IT AT ANY T IME WITHOUT PR IOR NOTI CE.
FCC/INDUSTRY CANADA NOTICE Your phone may cause TV or radio interference (for example, when using a telephone in close proximity to receiving equipment). The FCC or Industry Canada can require you to stop using your telep hone if such interference cannot be eliminated. If you require assistan ce, contact your local service facility. This device complies with part 15 of the FCC ru les. Operation is subject to the following two conditions: (1) This d evice may not cause harmful interference, and (2) this device must accept an y interference receiv ed, including interfe rence that may cause undesired operation.

Contents

For your safety.......................... 7
General information.............. 10
Overview of functions........................ 10
Access codes......................................... 10
Security code .................................... 10
PIN codes ........................................... 10
PUK codes .......................................... 11
Barring password............................. 11
Configuration settings service ........ 11
Download content and applications 12
Nokia support on the Web ............... 12
1. Get started ......................... 13
Open the fold ....................................... 13
Install the SIM card and
the battery ............................................ 13
Charge the battery.............................. 14
Switch the phone on and off........... 15
Plug and play service...................... 15
Normal operating position ............... 15
Wrist strap ............................................ 15
2. Your phone......................... 16
Keys and parts...................................... 16
Standby mode ...................................... 17
Mini display....................................... 17
Main display...................................... 17
Personal shortcut list ..................... 17
Shortcuts in the standby mode ... 18
Power saving..................................... 18
Indicators........................................... 18
Keypad lock (keyguard) ..................... 19
3. Call functions..................... 20
Make a call ........................................... 20
Speed dialing .................................... 20
Answer or reject a call....................... 20
Call waiting....................................... 21
Options during a call.......................... 21
4. Write text ........................... 22
Settings.................................................. 22
Predictive text input .......................... 22
Write compound words ................. 23
Traditional text input......................... 23
5. Navigate the menus........... 24
6. Messages............................. 25
Text messages (SMS) ......................... 25
Write and send a SMS message.. 26 Read and reply to a
SMS message.................................... 26
Templates........................................... 27
Multimedia messages (MMS).......... 27
Write and send a multimedia
message.............................................. 27
Read and reply to a multimedia
message.............................................. 29
Memory full .......................................... 29
Folders.................................................... 30
Postcards ............................................... 30
Send a postcard ............................... 31
Flash messages .................................... 31
Write a flash message.................... 31
Receive a flash message................ 31
Nokia Xpress audio messaging........ 31
Create and send an audio
message.............................................. 32
Receive an audio message............ 32
Instant messaging (IM) ..................... 32
Access the instant messaging
menu ................................................... 33
Connect to the instant messaging
service................................................. 33
Start an instant messaging
session ................................................ 33
Accept or reject an invitation...... 34
Read a received instant message 35
4
Participate in a conversation........ 35
Edit your availability status .......... 35
Contacts for instant messaging... 36
Block and unblock messages ........ 36
Groups ................................................. 36
E-mail application............................... 37
Write and send an e-mail.............. 37
Download e-mail.............................. 38
Read and reply to e-mail ............... 38
Inbox and other folders .................. 38
Delete e-mail messages ................. 39
Voice messages .................................... 39
Info messages ....................................... 39
Service commands .............................. 39
Delete messages .................................. 39
Message settings ................................. 40
Text and SMS e-mail....................... 40
Multimedia......................................... 40
E-mail .................................................. 41
Other settings ................................... 42
Message counter ................................. 42
7. Contacts.............................. 43
Search for a contact........................... 43
Save names and phone numbers.... 43
Save numbers, items, or an image.. 43
Copy contacts ....................................... 44
Edit contact details............................. 44
Delete contacts or contact details. 44
Business cards ...................................... 45
My presence.......................................... 45
Subscribed names................................ 46
Add contacts to the subscribed
names .................................................. 46
View the subscribed names........... 46
Unsubscribe a contact.................... 47
Settings .................................................. 47
Groups..................................................... 47
Voice dialing ......................................... 48
Add and manage voice tags .......... 48
Make a call with a voice tag ........ 49
Speed dials ............................................ 49
Info, service, and my numbers......... 49
8. Call register......................... 50
Recent calls lists .................................. 50
Counters and timers ........................... 50
9. Settings.............................. 51
Profiles.................................................... 51
Themes.................................................... 51
Tones ....................................................... 51
My shortcuts......................................... 52
Main display.......................................... 52
Mini display........................................... 53
Time and date....................................... 53
Call........................................................... 54
Phone ...................................................... 54
Connectivity .......................................... 55
Infrared ............................................... 55
Packet data (EGPRS) ....................... 56
Enhancements ...................................... 57
Configuration ....................................... 58
Security .................................................. 59
Restore factory settings .................... 59
10. Operator menu................. 60
11. Gallery .............................. 61
12. Media................................ 62
Camera ................................................... 62
Take a photo ...................................... 62
Record a video clip .......................... 62
Radio ....................................................... 62
Save radio channels ........................ 63
Listen to the radio ........................... 63
Recorder ................................................. 64
Record sound..................................... 64
List of recordings ............................. 64
13. Organiser .......................... 65
Alarm clock ........................................... 65
Stop the alarm .................................. 65
Calendar ................................................. 65
Make a calendar note ..................... 66
A note alarm...................................... 66
To-do list................................................ 66
5
Notes ...................................................... 67
Synchronization................................... 67
Synchronize from your phone...... 67
Synchronization settings............... 68
Synchronize from a
compatible PC .................................. 68
Calculator.............................................. 69
Stopwatch ............................................. 69
Countdown timer ................................ 70
14. Applications .................... 71
Games..................................................... 71
Launch a game ................................. 71
Game downloads ............................. 71
Game settings................................... 71
Collection .............................................. 71
Launch an application.................... 71
Other application options ............. 72
Download an application .............. 72
15. Push to talk ..................... 74
Push to talk menu............................... 74
Connect to and disconnect PTT....... 75
Make and receive a PTT call............. 75
Make a dial out PTT call ................ 75
Make a group call............................ 76
Make a one-to-one call................. 76
Receive a PTT call ............................ 77
Callback requests ................................ 77
Send a callback request................. 77
Respond to a callback request..... 78
Save the callback request sender 78
Add a one-to-one contact ............... 78
Create and set up groups.................. 79
PTT settings........................................... 80
16. Web.................................. 82
Set up browsing .................................. 82
Connect to a service .......................... 82
Browse pages ....................................... 83
Browse with phone keys................ 83
Options while browsing ................. 83
Direct calling .................................... 84
Appearance settings........................... 84
Cookies................................................... 85
Scripts over secure connection ....... 85
Bookmarks............................................. 85
Receive a bookmark........................ 85
Download files ..................................... 86
Service inbox ........................................ 86
Service inbox settings .................... 86
Cache memory ..................................... 87
Positioning information .................... 87
Browser security.................................. 88
Security module ............................... 88
Certificates ........................................ 89
Digital signature .............................. 89
17. SIM services..................... 91
18. PC connectivity................ 92
PC Suite ................................................. 92
Packet data, HSCSD, and CSD ......... 92
Data communication applications. 92
19. Battery information ........ 93
Charging and discharging ................ 93
Nokia battery authentication
guidelines .............................................. 93
20. Technical Information..... 96
CARE AND MAINTENANCE ... 97
Additional safety information 98
APPENDIX............................. 102
6

For your safety

For your safety
Read these simple guidelines. Not following them may be dangerous or illegal. Read the complete user guide for further information.
SWITCH ON SAFELY
Do not switch the phone on when wireless phone use is prohibited or when it may cause interference or danger.
ROAD SAFETY COMES FIRST
Obey all local laws. Always keep your hands free to operate the vehicle while driving. Your first consideration while driving should be road safety.
INTERFERENCE
All wireless phones may get interference, which could affect performance.
SWITCH OFF IN HOSPITALS
Follow any restrictions. Switch the phone off near medical equipment.
SWITCH OFF IN AIRCRAFT
Follow any restrictions. Wireless devices can cause interference in aircraft.
SWITCH OFF WHEN REFUELLING
Don't use the phone at a refuelling point. Don't use near fuel or chemicals.
SWITCH OFF NEAR BLASTING
Follow any restrictions. Don't use the phone where blasting is in progress.
USE SENSIBLY
Use only in the normal position as explained in the product documentation. Don't touch the antenna unnecessarily.
QUALIFIED SERVICE
Only qualified personnel may install or repair this product.
ENHANCEMENTS AND BATTERIES
Use only approved enhancements and batteries. Do not connect incompatible products.
7
For your safety
WATER-RESISTANCE
Your phone is not water-resistant. Keep it dry.
BACK-UP COPIES
Remember to make back-up copies or keep a written record of all important information stored in your phone.
CONNECTING TO OTHER DEVICES
When connecting to any other device, read its user guide for detailed safety instructions. Do not connect incompatible products.
EMERGENCY CALLS
Ensure the phone is switched on and in service. Press the end key as many times as needed to clear the display and return to the start screen. Enter the emergency number, then press the call key. Give your location. Do not end the call until given permission to do so.
About your device
The wireless device described in this guide is approved for use on the EGSM 900 and GSM 1800 and 1900 networks. Contact your service provider for more information about networks.
When using the features in this device, obey all laws and respect the privacy and legitimate rights of others.
Warning: To use any features in this device, other than the alarm clock, the device must be switched on. Do not switch the device on when wireless device use may cause interference or danger.
Network services
To use the phone you must have service from a wireless service provider. Many of the features in this device depend on features in the wireless network to function. These network services may not be available on all networks or you may have to make specific arrangements with your service provider before you can utilize network services. Your service provider may need to give you additional instructions for their use and explain what charges will apply. Some networks may have limitations that affect how you can use network services. For instance, some networks may not support all language-dependent characters and services.
Your service provider may have requested that certain features be disabled or no t activated in your device. If so, they will not appear on your device menu. Your device may also have been specially configured for your network provider. This
8
For your safety
configuration may include changes in menu names, menu order and icons. Contact your service provider for more information.
This device supports WAP 2.0 protocols (HTTP and SSL) that run on TCP/IP protocols. Some features of this device, such as text messages, multimedia messages, audio messages, instant messaging service, e-mail, presence enhanced contacts, mobile Internet services, content and application download, and synchronization with a remote Internet server, require network support for these technologies.
Shared memory
The phone has two memories. The following features may share the first memory: contacts, text messages, multimedia messages (but no attachments), instant messaging, groups, voice commands, calendar, and to-do notes. The second shared memory is used by files stored in Gallery, attachments of multimedia messages, e-mail, and Java may reduce the memory available for the remaining features sharing memory. For example, saving many Java applications may use all of the available memory. Your device may display a message that the memory is full when you try to use a shared memory feature. In this case, delete some of the information or entries stored in the shared memory features before continuing. Some of the features, such as text messages, may have a certain amount of memory specially allotted to them in addition to the memory shared with other features.
TM
applications. Use of one or more of these features
Enhancements
A few practical rules about accessories and enhancements are as follows:
• Keep all accessories and enhancements out of the reach of small children.
• When you disconnect the power cord of any accessory or enhancement, grasp and pull the plug, not the cord.
• Check regularly that enhancements installed in a vehicle are mounted and are operating properly.
• Installation of any complex car enhancements must be made by qualified personnel only.
9

General information

General information

Overview of functions

Your phone provides many functions that are practical for daily use, such as a calendar, a clock, an alarm clock, a radio, and a built-in camera. Your phone also supports the following functions:
• Enhanced data rates for GSM evolution (EDGE), see “Packet data (EGPRS),” p. 56
• Extensible hypertext markup language (XHTML), see “Web,” p. 82
• Audio messaging, see “Nokia Xpress audio messaging,” p. 31
• Instant messaging, see “Instant messaging (IM),” p. 32
• e-mail application, see “E-mail application,” p. 37
• Push to talk, see “Push to talk,” p. 74
• Presence-enhanced contacts, see “My presence,” p. 45
• Java 2 Platform, Micro Edition (J2METM), see “Applications,” p. 71

Access codes

Security code

The security code (5 to 10 digits) helps to protect your phone against unauthorized use. The preset code is 12345. To change the code, and to set the phone to request the code, see “Security,” p. 59.

PIN codes

The personal identification number (PIN) code and the universal personal identification number (UPIN) code (4 to 8 digits) help to protect your SIM card against unauthorized use. See “Security,” p. 59.
The PIN2 code (4 to 8 digits) may be supplied with the SIM card and is required for some functions.
The module PIN is required to access the information in the security module. See “Security module,” p. 88.
10
General information
The signing PIN is required for the digital signature. See “Digital signature,” p. 89.

PUK codes

The personal unblocking key (PUK) code and the universal personal unblocking key (UPUK) code (8 digits) is required to change a blocked PIN code and UPIN code, respectively. The PUK2 code (8 digits) is required to change a blocked PIN2 code. If the codes are not supplied with the SIM card, contact your local service provider for the codes.

Barring password

The barring password (4 digits) is required when using the Call barring
service. See “Security,” p. 59.

Configuration settings service

To use some of the network services, such as mobile Internet services, MMS, Nokia Xpress audio messaging, or remote Internet server synchronization, your phone needs the correct configuration settings. You may be able to receive the settings directly as a configuration message. After receiving the settings you need to save them on your phone. The service provider may provide a PIN that is needed to save the settings. For more information on availability, contact your network operator, service provider, nearest authorized Nokia dealer, or visit the support area on the Nokia Web site, <www.nokia.com/support>.
When you have received a configuration message Configuration sett.
received is displayed.
To save the settings, select Show > Save. If the phone requests Enter
settings' PIN:, enter the PIN code for the settings, and select OK. To
receive the PIN code, contact the service provider that supplies the settings. If no settings are saved yet, these settings are saved and set as default configuration settings. Otherwise, the phone asks Activate saved
configuration settings?.
To discard the received settings, select Exit or Show > Discard.
To edit the settings, see “Configuration,” p. 58.
11
General information

Download content and applications

You may be able to download new content (for example, themes) to the phone (network service). Select the download function (for example, in the Gallery menu). To access the download function, see the respective menu descriptions. For the availability of different services, pricing, and tariffs, contact your service provider.
Important: Use only services that you trust and that offer adequate security and protection against harmful software.

Nokia support on the Web

Check <www.nokia.com/support> or your local Nokia Web site for the latest version of this guide, additional information, downloads, and services related to your Nokia product.
12
Get started

1. Get started

Open the fold

When you open the fold of the phone, it opens up to approximately 155 degrees. Do not try to force the fold open more.

Install the SIM card and the battery

Always switch the device off and disconnect the charger before removing the battery.
Keep all SIM cards out of the reach of small children. For availability and information on using SIM card services, contact your SIM card vendor. This may be the service provider, network operator, or other vendor.
This device is intended for use with BL-4C battery.
The SIM card and its contacts can easily be damaged by scratches or bending, so be careful when handling, inserting, or removing the card.
To remove the back cover of the phone press the release buttons (1), and slide the back cover to remove it from the phone (2).
Remove the battery as shown(3). Release the SIM card holder (4).
13
Get started
Insert the SIM card (5). Make sure that the SIM card is properly inserted, and that the golden contact area on the card is facing downwards. Close the SIM card holder (6) and press it until it snaps into position.
Replace the battery (7). Observe the battery contacts. Always use original Nokia batteries. See “Nokia battery authentication guidelines,” p. 93.
Slide the back cover into its place (8, 9).

Charge the battery

Warning: Use only batteries, chargers, and enhancements approved by
Nokia for use with this particular model. The use of any other types may invalidate any approval or warranty, and may be dangerous.
Check the model number of any charger before use with this device. This device is intended for use when supplied with power from an AC-3, AC-4, and DC-4 charger, and from AC-1, ACP-7, ACP-12, and LCH-12 charger when used with the charger adapter CA-44 delivered with your phone.
For availability of approved enhancements, please check with your dealer.
1. Connect the charger to a wall socket.
2. Connect the lead from the charger to the socket on the bottom of your phone.
If the battery is completely discharged, it may take a few minutes before the charging indicator appears on the display or before any calls can be made.
The charging time depends on the charger and the battery used. For example, charging a BL-4C battery with the AC-3 charger takes approximately 2 hours and 12 minutes while the phone is in the standby mode.
14
Get started

Switch the phone on and off

Warning: Do not switch the phone on when wireless phone use is
prohibited or when it may cause interference or danger.
Press and hold the end key.
If the phone asks for a PIN or a UPIN code, enter the code (displayed as ****), and select OK.

Plug and play service

When you switch on your phone for the first time, and the phone is in the standby mode, you are asked to get the configuration settings from your service provider (network service). Confirm or decline the query. See "Connect to service provider support ," p. 58, and “Configuration settings service,” p. 11.

Normal operating position

Use the phone only in its normal operating position.
Your device has an external antenna.
Note: As with any other radio transmitting device, do not touch the antenna unnecessarily when the device is switched on. Contact with the antenna affects call quality and may cause the device to operate at a higher power level than otherwise needed. Avoiding contact with the antenna area when operating the device optimizes the antenna performance and the battery life.

Wrist strap

Remove the back cover and the battery. Insert the strap as shown in the picture. Replace the battery and the back cover.
15
Your phone

2. Your phone

Keys and parts

• Earpiece (1)
• Main display (2)
• Left selection key (3)
Middle selection key (4)
Right selection key (5)
The function of these keys depends on the guiding text shown on the display above the keys.
• Volume key (6)
• 4-way navigation key (7)
Scroll up, down, left, and right.
• Call key (8)
• Push to talk (PTT) key, and camera release key (9)
• Infrared (IR) port (10)
• End key and power key (11)
• Charger connector (12)
• Pop-PortTM connector (13)
• Microphone (14)
• Loudspeaker (15)
• Camera lens (16)
• Mini display (17)
16
Your phone

Standby mode

When the phone is ready for use, and you have not entered any characters, the phone is in the standby mode.

Mini display

When the fold is closed, the mini display may show the following:
• The signal strength of the cellular network at your current location and the battery charge level
• The name of the network, or if the phone is not in service, it is indicated by a text note
• The time and date, the active profile, and the alarm clock or calendar note alerts
When you have an incoming call, the caller’s name or number is shown if it is identified.

Main display

• Name of the network or the operator logo (1)
• Signal strength of the cellular network at your current location (2)
• Battery charge level (3)
• Left selection key is Go to (4).
• Middle selection key is Menu (5)
• Right selection key is Names (6) or another shortcut to a function that you selected. See “My shortcuts,” p. 52. Operator variants may have an operator­specific name to access an operator-specific Web site.

Personal shortcut list

The left selection key is Go to.
To view the functions in the personal shortcut list, select Go to. To activate a function select it.
17
Your phone
To view a list with available functions, select Go to > Options > Select
options. To add a function to the shortcut list, select Mark. To remove a
function from the list, select Unmark.
To rearrange the functions on your personal shortcut list, select Go to >
Options > Organise. Select the desired function and Move and the place
where you want to move the function.

Shortcuts in the standby mode

• To access the list of dialed numbers, press the call key once. Scroll to the number or name that you want; and to call the number, press the call key.
• To open the web browser, press and hold 0.
• To call your voice mailbox, press and hold 1 .
• Use the navigation key as a shortcut. See “My shortcuts,” p. 52.

Power saving

A digital clock view overwrites the display when no function of the phone has been used for a certain period of time. To activate the power saver, see
Powe r sav er in “Main display,” p. 52, and “Mini
display,” p. 53. To deactivate the screen saver, open the fold, or press any key.

Indicators

You received one or several text or picture messages. See “Read and reply to a SMS message,” p. 26.
You received one or several multimedia messages. See “Read and reply to a multimedia message,” p. 29.
The phone registered a missed call. See “Call register,” p. 50.
The keypad is locked. See “Keypad lock (keyguard),” p. 19.
18
Your phone
The phone does not ring for an incoming call or text message when Incoming call alert and Message alert tone are set to Off. See “Tones,” p. 51.
The alarm clock is set to On. See “Alarm clock,” p. 65.
When the packet data connection mode Always online is selected and the packet data service is available, the indicator is shown. See “Packet data (EGPRS),” p. 56.
A packet data connection is established. See “Packet data (EGPRS),” p. 56 and “Browse pages,” p. 83.
The packet data connection is suspended (on hold), for example, if there is an incoming or outgoing call during a packet data dial-up connection.
When the infrared connection is activated, the indicator is shown continuously.

Keypad lock (keyguard)

To prevent the keys from being accidentally pressed, select Menu, and press * within 3.5 seconds to lock the keypad.
To unlock the keypad, select Unlock, and press *. If the Security keyguard is set On, enter the security code if requested.
To answer a call when the keyguard is on, press the call key. When you end or reject the call, the keypad automatically locks.
For Automatic keyguard and Security keyguard, see “Phone,” p. 54.
When the keyguard is on, calls still may be possible to the official emergency number programmed into your device.
19
Call functions

3. Call functions

Make a call

1. Enter the phone number, including the area code.
For international calls, press * twice for the international prefix (the + character replaces the international access code) and then enter the country code, the area code without the leading 0, if necessary, and the phone number.
2. To call the number, press the call key.
3. To end the call or to cancel the call attempt, press the end key, or close the phone.
To make a call using names, search for a name or phone number in
Contacts, see “Search for a contact,” p. 43. Press the call key to call the
number.
To access the list of up to 20 numbers you last called or attempted to call, press the call key once in the standby mode. To call the number, select a number or name, and press the call key.

Speed dialing

Assign a phone number to one of the speed-dialing keys, 2 to 9. See “Speed dials,” p. 49. Call the number in either of the following ways:
• Press a speed-dialing key, and then press the call key.
•If Speed dialling is set to On, press and hold a speed-dialing key until the call begins. See Speed dialli ng in “Call,” p. 54.

Answer or reject a call

To answer an incoming call, press the call key, or open the phone. To end the call, press the end key, or close the phone.
To reject an incoming call, press the end key, or if the phone is open, close the phone. To reject an incoming call when the phone is closed, open the phone, and press the end key within 1.5 seconds.
20
Call functions
To mute the ringing tone, press one of the volume keys, or select Silence.
Tip: If the Divert if busy function is activated to divert the calls (for example, to your voice mailbox) rejecting an incoming call also diverts the call. See “Call,” p. 54.
If a compatible headset supplied with the headset key is connected to the phone, to answer and end a call, press the headset key.

Call waiting

To answer the waiting call during an active call, press the call key. The first call is put on hold. To end the active call, press the end key.
To activate the Call waiting function, see “Call,” p. 54.

Options during a call

Many of the options that you can use during a call are network services. For availability, contact your network operator or service provider.
During a call, select Options and from the following options:
Call options are Mute or Unmute, Contacts, Menu, Record, Lock keypad,
Audio enhancing, Loudspeaker or Handset.
Network services options are Answer and Reject, Hold or Unhold, New
call, Add to conference, End call, End all calls, and the following:
Send DTMF — to send tone strings
Swap — to switch between the active call and the call on hold
Transfer — to connect a call on hold to an active call and disconnect
yourself
Conference — to make a conference call that allows up to five persons to
take part in a conference call
Private call —to discuss privately in a conference call
Warning: Do not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely loud.
21
Write text

4. Write text

You can enter text (for example, when writing messages) using traditional or predictive text input. When using traditional text input, press a number key, 1 to 9, repeatedly until the desired character appears. In predictive text input you can enter a letter with a single keypress.
When you are writing text, predictive text input is indicated by and traditional text input by at the top left of the display. ,
, or appear next to the text input indicator, indicating the
character case.
To change the character case and the text input mode, press #. indicates number mode. To change from the letter to number mode, press and hold #, and select Number mode.

Settings

To set the writing language, select Options > Writing language. Predictive text input is only available for the languages listed.
Select Options > Dictionary on to set the predictive text input or
Dictionary off to set traditional text input.

Predictive text input

Predictive text input is based on a built-in dictionary to which you can also add new words.
1. Start writing a word using the 2 to 9 keys. Press each key only once for a single letter. The word changes after each keypress.
2. When you have finished writing the word and it is correct, to confirm it, press 0 to add a space, or press any of the navigation keys. Press a navigation key to move the cursor.
If the word is not correct, press * repeatedly, or select Options >
Matches. When the word that you want appears, confirm it.
22
Write text
If ? is displayed after the word, the word you intended to write is not in the dictionary. To add the word to the dictionary, select Spell. Enter the word (traditional text input is used), and select Save.
3. Start writing the next word.

Write compound words

Enter the first part of the word, and press the navigation key right to confirm it. Write the last part of the word, and confirm the word.

Traditional text input

Press a number key, 1 to 9, repeatedly until the desired character appears. Not all characters available under a number key are printed on the key. The characters available depend on the writing language. See “Settings,” p. 22.
If the next letter you want is located on the same key as the present one, wait until the cursor appears, or press any of the navigation keys and enter the letter.
The most common punctuation marks and special characters are available under the 1 key.
23
Navigate the menus

5. Navigate the menus

The phone offers you an extensive range of functions, which are grouped into menus.
1. To access the menu, select Menu. To change the menu view, select
Options > Main menu view > List or Grid.
2. Scroll through the menu, and select a submenu (for example,
Settings).
3. If the menu contains submenus, select the one that you want (for example, Call).
4. If the selected menu contains further submenus, select the one that you want (for example, Anykey answer).
5. Select the setting of your choice.
6. To return to the previous menu level, select Back. To exit the menu, select Exit.
24
Messages

6. Messages

The message services can only be used if they are supported by your network or your service provider.
Note: When sending messages, your phone may display the words
Message sent. This is an indication that the message has been sent by
your device to the message centre number programmed into your device. This is not an indication that the message has been received at the intended destination. For more details about messaging services, check with your service provider.
Important: Exercise caution opening messages. Messages may contain malicious software or otherwise be harmful to your device or PC.
Only devices that have compatible features can receive and display messages. The appearance of a message may vary depending on the receiving device.

Text messages (SMS)

Using the short message service (SMS) you can send and receive multipart messages made of several ordinary text messages (network service) that can contain pictures.
Before you can send any text, picture, or e-mail message, you must save your message center number. See “Message settings,” p. 40.
To check SMS e-mail service availability and to subscribe to the service, contact your service provider.
Your device supports the sending of text messages beyond the character limit for a single message. Longer messages will be sent as a series of two or more messages. Your service provider may charge accordingly. Characters that use accents or other marks, and characters from some language options like Chinese, take up more space limiting the number of characters that can be sent in a single message.
At the top of the display, you can see the message length indicator that tracks the number of characters available. For example, 10/2 means that you can still add 10 characters for the text to be sent as two messages.
25
Messages

Write and send a SMS message

1. Select Menu > Messages > Create message > Text message.
2. Enter a message. See “Write text,” p. 22. To insert text templates or a picture into the message, see “Templates,” p. 27. Each picture message comprises several text messages. Sending one picture or multipart message may cost more than sending one text message.
3. To send the message, select Send > Recently used, To phone number,
To many, or To e-mail address. To send a message using a predefined
message profile, select Via sending profile. For the message profile, see “Text and SMS e-mail,” p. 40. Select or enter a phone number or e-mail address, or select a profile.

Read and reply to a SMS message

is shown when you received an SMS message or an SMS e-mail. The blinking indicates that the message memory is full. Before you can receive new messages, delete some of your old messages in the Inbox folder.
1. To view a new message, select Show. To view it later, select Exit.
To read the message later, select Menu > Messages > Inbox. If more than one message is received, select the message that you want to read. indicates an unread message.
2. While reading a message, select Options and delete or forward the
message; edit the message as a text message or an SMS e-mail, rename the message you are reading or move it to another folder; or view or extract message details. You can also copy text from the beginning of the message to your phone calendar as a reminder note. To save the picture in the Templates folder when reading a picture message, select Save picture.
3. To reply as a message, select Reply > Text message, Multimedia msg.
or Flash message. Enter the reply message. When replying to an e-mail, first confirm or edit the e-mail address and subject.
4. To send the message to the displayed number, select Send > OK.
26
Messages

Templates

Your phone has text templates and picture templates that you can use in text, picture, or SMS e-mail messages.
To access the template list, select Menu > Messages > Saved items >
Text messages > Templates.

Multimedia messages (MMS)

A multimedia message can contain text, sound, a picture, a calendar note, a business card, or a video clip. If the message is too large, the phone may not be able to receive it. Some networks allow text messages that include an Internet address where you can view the multimedia message.
You cannot receive multimedia messages during a call, a game, another Java application, or an active browsing session over GSM data. Because delivery of multimedia messages can fail for various reasons, do not rely solely upon them for essential communications.

Write and send a multimedia message

To set the settings for multimedia messaging, see “Multimedia,” p. 40. To check availability and to subscribe to the multimedia messaging service, contact your service provider.
1. Select Menu > Messages > Create message > Multimedia msg..
2. Enter a message. See “Write text,” p. 22.
To insert a file, select Options > Insert and from the following options:
Image, Sound clip or Video clip — to insert a file from Gallery
New image opens the Camera — to take a new image to be added to
the message
New sound clip opens the Recorder — to make a new record to be
added to the message
Business card or Calendar note — to insert a business card or a
calendar note in the message.
27
Messages
Slide — to insert a slide to the message. Your phone supports
multimedia messages that contain several pages (slides). Each slide can contain text, one image, a calendar note, a business card, and one sound clip. To open a desired slide if the message contains several slides, select Options > Previous slide, Next slide, or Slide list. To set the interval between the slides, select Options > Slide timing. To move the text component to the top or bottom of the message, select Options > Place text first or Place text last.
The following options may also be available: Delete to delete an image, slide, or sound clip from the message, Clear text, Preview, or
Save message. In More options the following options may be
available: Insert contact, Insert number, Message details, and Edit
subject.
3. To send the message, select Send > Recently used, To phone number,
To e-mail address, or To many.
4. Select the contact from the list, or enter the recipient’s phone
number or e-mail address, or search for it in Contacts. Select OK. The message is moved to the Outbox folder for sending.
While the multimedia message is being sent, the animated indicator
is displayed and you can use other functions on the phone. If the sending fails, the phone tries to resend it a few times. If this fails, the message remains in the Outbox folder, and you can try to resend it later.
If you select Save sent messages > Yes, the sent message is saved in the Sent items folder. See “Multimedia,” p. 40. When the message is sent, it is not an indication that the message has been received at the intended destination.
Copyright protections may prevent some images, ringing tones, and other content from being copied, modified, transferred or forwarded.
28
Messages

Read and reply to a multimedia message

The default setting of the multimedia message service is generally on.
Important: Exercise caution when opening messages. Multimedia message objects may contain malicious software or otherwise be harmful to your device or PC.
When your phone receives a multimedia message, the animated is displayed. When the message has been received, and the text
Multimedia message received are shown.
1. To read the message, select Show. To view it later, select Exit.
To read the message later, select Menu > Messages > Inbox. In the list of messages, indicates an unread message. Select the message that you want to view.
2. The function of the middle selection key changes according to the currently displayed attachment in the message.
To view the whole message if the received message contains a presentation, a sound clip, or view a video clip, select Play.
To zoom in on an image, select Zoom. To view a business card or calendar note or to open a theme object, select Open.
3. To reply to the message, select Options > Reply > Text message,
Multimedia msg., or Flash message. Enter the reply message, and
select Send. You can send the reply message only to the person who sent you the original message.
Select Options to access available options.

Memory full

When you have received a new text message and the message memory is full, blinks and Text msgs. memory full. Delete msgs. is shown. Select No, and delete some messages from a folder. To discard the waiting message, select Exit > Yes.
When you have a new multimedia message waiting and the memory for the messages is full, blinks and Multimedia memory full. View
waiting msg. is shown. To view the waiting message, select Show.
29
Messages
Before you can save the waiting message, delete old messages to free memory space. To save the message, select Save.
To discard the waiting message, select Exit > Yes. If you select No, you can view the message.

Folders

The phone saves received text and multimedia messages in the Inbox folder.
Multimedia messages that have not yet been sent are moved to the
Outbox folder.
If you have selected Message settings > Text messages > Save sent
messages > Yes , and Message settings > Multimedia msgs. > Save sent messages > Yes , the sent messages are saved in the Sent items folder.
To save the text message that you are writing and wish to send later in the Saved items folder, select Options > Save message > Saved text
msgs.. For multimedia messages, select the option Save message.
indicates unsent messages.
To organize your text messages, you can move some of them to My
folders or add new folders for your messages. Select Messages > Saved items > Text messages > My folders.
To add a folder, select Options > Add folder. If you have not saved any folders, select Add.
To delete or rename a folder, scroll to the desired folder, and select
Options > Delete folder or Rename folder.

Postcards

With the postcard messaging service you can create and send post cards that may contain an image and a greeting text. The postcard is sent to the service provider via multimedia messaging. The service provider prints the post card and send it to the postal address given with the message. Multimedia messaging service must be activated before this service can be used.
30
Loading...
+ 80 hidden pages