The crossed-out wheeled bin means that within the European Union the
product must be taken to separate collection at the product end-of-life.
This applies to your device but also to any enhancements marked with
this symbol. Do not dispose of these products as unsorted municipal
document in any form without the prior written permission of Nokia is prohibited.
Nokia, Nokia Connecting People, Visual Radio, and Pop-Port are trademarks or
registered trademarks of Nokia Corporation. Other product and company names
mentioned herein may be trademarks or tradenames of their respective owners.
Nokia tune is a sound mark of Nokia Corporation.
This product includes software licensed from Symbian Software Ltd (c) 1998200(6). Symbian and Symbian OS are trademarks of Symbian Ltd.
We, NOKIA CORPORATION declare under our sole
responsibility that the product RM-55 is in
conformity with the provisions of the following
Council Directive: 1999/5/EC. A copy of the
Declaration of Conformity can be found at http:/
/www.nokia.com/phones/
declaration_of_conformity/
Under no circumstances shall Nokia be responsible for any loss of data or income
or any special, incidental, consequential or indirect damages howsoever caused.
The contents of this document are provided ‘as is’. Except as required by a pplicable
law, no warranties of any kind, either express or implied, including, but not limited
to, the implied warranties of merchantability and fitness for a particular purpose,
are made in relation to the accuracy, reliability or contents o f this document. Nokia
reserves the right to revise this document or withdraw it at any time without prior
notice.
The availability of particular products may vary by region. Please check with the
Nokia dealer nearest to you.
Export Controls
This device may contain commodities, technology or software subject to export
laws and regulations from the US and other countries. Diversion contrary to law is
prohibited.
FCC / INDUSTRY CANADA NOTICE
Your device may cause TV or radio interference (for example, when using a
telephone in close proximity to receiving equipment). The FCC or Industry Canada
can require you to stop using your telephone if such interference cannot be
eliminated. If you require assistance, contact your local service facility. This device
complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful intereference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation. Any changes or modifications not expressly approved by the
Nokia could void the user's authority to operate this equipment.
ISSUE 1 EN, 9248943
3
Contents
For your safety...........................................6
Your Nokia N93.........................................9
Battery information ............................. 115
Charging and discharging...............................................115
Nokia battery authentication guidelines....................115
Care and maintenance ......................... 118
Additional safety information............. 119
Index ...................................................... 122
For your safety
Read these simple guidelines. Not following them may be
dangerous or illegal. Read the complete user guide for
further information.
SWITCH ON SAFELY Do not switch the
device on when wireless phone use is
prohibited or when it may cause interference
or danger.
ROAD SAFETY COMES FIRST Obey all local
laws. Always keep your hands free to operate
the vehicle while driving. Your first
consideration while driving should be road
safety.
INTERFERENCE All wireless devices may be
susceptible to interference, which could affect
performance.
SWITCH OFF IN HOSPITALS Follow any
restrictions. Switch the device off near
medical equipment.
SWITCH OFF IN AIRCRAFT Follow any
restrictions. Wireless devices can cause
interference in aircraft.
FCC DRAFT
6
SWITCH OFF WHEN REFUELING Do not use
the device at a refueling point. Do not use near
fuel or chemicals.
SWITCH OFF NEAR BLASTING Follow any
restrictions. Do not use the device where
blasting is in progress.
USE SENSIBLY Use only in the normal
position as explained in the product
documentation. Do not touch the antenna
unnecessarily.
QUALIFIED SERVICE Only qualified personnel
may install or repair this product.
ENHANCEMENTS AND BATTERIES Use only
approved enhancements and batteries. Do not
connect incompatible products.
WATER-RESISTANCE Your device is not
water-resistant. Keep it dry.
BACK-UP COPIES Remember to make
back-up copies or keep a written record of all
important information.
CONNECTING TO OTHER DEVICES When
connecting to any other device, read its user
guide for detailed safety instructions. Do not
connect incompatible products.
EMERGENCY CALLS Ensure the phone
function of the device is switched on and in
service. The keypad is active only in the Fold
open mode. Press as many times as
needed to clear the display and return to the
start screen. Enter the emergency number,
then press . Give your location. Do not end
the call until given permission to do so.
About your device
The wireless device described in this guide is approved for
use on the EGSM 900/1800/1900 and UMTS 2100
networks. Contact your service provider for more
information about networks.
When using the features in this device, obey all laws and
respect privacy and legitimate rights of others.
When taking and using images or video clips, obey all laws
and respect local customs as well as privacy and legitimate
rights of others.
This device supports common features of Microsoft Word,
PowerPoint, and Excel (Microsoft Office 97, 2000, XP, and
2003). Not all file formats can be viewed or modified.
Warning: To use any features in this device, other
than the alarm clock, the device must be switched on.
Do not switch the device on when wireless device use
may cause interference or danger.
Network services
To use the device you must have service from a wireless
service provider. Many of the features in this device
depend on features in the wireless network to function.
These network services may not be available on all
networks or you may have to make specific arrangements
with your service provider before you can utilize network
services. Your service provider may need to give you
additional instructions for their use and explain what
charges will apply. Some networks may have limitations
that affect how you can use network services. For
instance, some networks may not support all
language-dependent characters and services. Network
features are designated in this guide by (network services).
Your service provider may have requested that certain
features be disabled or not activated in your device. If so,
they will not appear on your device menu. Your device may
also have been specially configured. This configuration
7
may include changes in menu names, menu order, and
icons. Contact your service provider for more information.
This device supports WAP 2.0 protocols (HTTP and SSL)
that run on TCP/IP protocols. Some features of this device,
such as MMS, browsing, e-mail, and content downloading
using the browser or over MMS, require network support
for these technologies.
For availability and information on using SIM card
services, contact your SIM card vendor. This may be the
service provider, network operator, or other vendor.
Enhancements, batteries, and
chargers
Always switch the device off and disconnect the charger
before removing the battery.
Check the model number of any charger before use with
this device. This device is intended for use when supplied
with power from a DC-4, AC-3, or AC-4 charger, and from
an AC-1, ACP-7, ACP-8, ACP-9, ACP-12, LCH-8, LCH-9, or
LCH-12 charger when used with the CA-44 charger
adapter.
The battery intended for use with this device is BP-6M.
Warning: Use only batteries, chargers, and
enhancements approved by Nokia for use with this
particular model. The use of any other types may
invalidate any approval or warranty, and may be
dangerous.
For availability of approved enhancements, please check
with your dealer. When you disconnect the power cord of
any enhancement, grasp and pull the plug, not the cord.
8
FCC DRAFT
Your Nokia N93
Model number: Nokia N93-1
Hereinafter referred to as Nokia N93.
Modes
Your device has four mechanical modes that are optimized
for different use situations: Fold closed for carrying, Fold open for traditional mobile phone use, Imaging for
recording video and taking pictures, and View for viewing
your images and videos. To switch between the modes,
turn the fold and the swing axis display. There is a short
time-out before a mode is activated.
Fold closed mode
When the fold is closed, the main display
deactivates and the cover display lights
up. Ongoing calls end, unless the
loudspeaker is in use or a compatible
headset is connected. To change the
settings, see ‘Cover display’, p. 96. If you
are using the player to listen to a sound
clip, it continues to play.
In the Fold closed mode, the cover display provides clock
and status information. On the standby mode display, the
signal strength and battery indicators, time information,
status indicators, and the name of the active profile (if
other than General) may be shown. If you are using the
music player to listen to a sound clip, volume bars and
track information are displayed. Use the side scroll keys to
play, pause, play the next/previous sound clip, and turn
the volume up or down.
If you are using Visual Radio in the Fold closed mode, the
visual content is not shown on the cover display. You can
store several preset stations with station name, frequency,
and location information. This information is shown on
the cover display. To turn the audio on and off, change the
channel, and seek new channels, use the scroll key on the
side of the device.
Calendar and clock alarms and notes for missed calls and
new received messages are also displayed. To view
received text messages and the text and image objects of
received multimedia messages, open the fold, and view
the message on the main display.
Incoming calls are indicated by their normal tone and a
note. In the cover display settings, select Answer if fold
opened to answer a call when you open the fold. If a
Your Nokia N93
9
compatible headset is connected to the device, press the
answer key on the headset. To change the settings, see
‘Cover display’, p. 96.
To make calls or use the menu, open the fold.
To can use the cover display as a torch light, press the
flash key on the side of the device. To operate the torch
light:
Your Nokia N93
• Quickly press the flash key once. The torch light is
activated for 1.5 seconds.
• Quickly press the flash key twice. The torch light is
activated for 3 minutes, or until you press the flash key
again.
• Press and hold the flash key. The torch light is
activated and stays on for as long as you hold the key
or until the 3 minute time-out ends.
Fold open mode
When you open the fold, the
Fold open mode is activated
automatically: the main
display lights up, the keypad is
available, and you can access
the menu. Scroll in the menu
with the scroll key.
The Fold open mode is
activated even if the fold is
not fully opened. The fold opens about 160 degrees, as
shown in the picture. Do not force the fold to open more.
Imaging mode
When you open the fold up
to 90 degrees, hold the
device sideways, and turn
the fold down so that the
main display faces you, the
Imaging mode is activated.
The main camera is
activated, and you can see
the view to be captured.
In the Imaging mode, you
can record videos and take pictures. See ‘Camera’, p. 22.
In the Imaging mode, the keypad is not active. You can use
the capture key, zoom key, side scroll key, camera mode
key, and flash key (all located on the side of the device),
power key, and the landscape selection keys and selection
keys next to the main display.
View mode
When the fold is closed and you lift the side of the swing
axis display when the fold is closed, the View mode is
activated.
10
FCC DRAFT
Use the View mode to do
the following:
• View your images.
• Activate photos and
movies from the
gallery to watch
slideshows.
• Make hands free
video calls and send
live video during a
video call. Adjust the angle of the display for optimum
secondary camera angle.
Useful shortcuts
Use shortcuts to quickly get the most from your device.
Refer to the relevant sections in this user guide for further
details of the functions.
Standby mode
• To switch between applications that are open, press
and hold , and select an application. If memory is
low, the device may close some applications. The device
saves any unsaved data before closing an application.
Leaving applications running in the background
increases the demand on battery power and reduces
the battery life.
• To start the camera, fully press the capture key in the
Imaging mode.
• To call your voice mailbox (network service), press and
hold .
• To open multimedia applications, press and hold .
See ‘Media Key’, p. 95.
• To change the profile, press , and select a profile.
• To switch between the General and Silent profiles,
press and hold . If you have two phone lines, this
action switches between the two lines.
• To open the last dialed numbers list, press .
• To use voice commands, press and hold .
• To start a connection to Services, press and hold .
See ‘Web’, p. 65.
For other shortcuts available in the standby mode, see
‘Active standby mode’, p. 94.
Edit text and lists
• To mark an item in a list, scroll to it, and press and
at the same time.
• To mark multiple items in a list, press and hold
while you press or . To end the selection, release
, then release .
• To copy and paste text: To select letters and words,
press and hold . At the same time, press or
to highlight text. To copy the text to clipboard, while
still holding , select Copy. To insert the text into a
document, press and hold , and select Paste.
Your Nokia N93
11
Settings
Your Nokia N93 normally has MMS, GPRS, streaming, and
mobile Internet settings automatically configured in the
device, based upon your service provider or network
operator information. You may have settings from your
service providers already installed in your device, or you
may receive the settings from the service providers as a
Your Nokia N93
special text message.
Transfer content from
another device
You can copy content such as contacts and calendar
entries from a compatible Nokia phone to your Nokia N93
using Bluetooth connectivity or infrared. The type of
content that can be copied depends on the phone model.
Copyright protections may prevent some images, music
(including ringing tones), and other content from being
copied, modified, transferred or forwarded.
You can insert your SIM card in the other device. When
your Nokia N93 is switched on without a SIM card, the
offline profile is automatically activated.
Transfer content
1 Press , and select Transfer on your Nokia N93.
2 In the information view, select Continue.
3 Select whether you want to use Bluetooth connectivity
or infrared to transfer the data. Both devices must
support the selected connection type.
4 If you select Bluetooth connectivity, to have your Nokia
N93 search for devices with Bluetooth connectivity,
select Continue. Select your other device from the list.
You are asked to enter a code on your Nokia N93. Enter
a code (1-16 digits), and select OK. Enter the same
code on the other device, and select OK. The devices are
now paired. See ‘Pair devices’, p. 81.
For some phone models, the Transfer application is
sent to the other device as a message. To install
Transfer on the other device, open the message, and
follow the instructions on the display.
If you select infrared, connect the two devices. See
‘Infrared connection’, p. 82.
5 From your Nokia N93, select the content you want to
copy from the other device.
Content is copied from the memory and compatible
memory card (if inserted) of the other device to the
corresponding location in your Nokia N93 and memory
card (if inserted). The copying time depends on the amount
of data to be transferred. You can cancel copying and
continue later.
To view the log information of a previous transfer, in the
main view, select Transfer log.
12
FCC DRAFT
To view the devices you have copied or transferred data
from, in the main view, select Phones.
Essential indicators
The device is being used in a GSM network.
The device is being used in a UMTS network (network
service).
You have one or more unread messages in the Inbox
folder in Messag..
You have received new e-mail in the remote mailbox.
There are messages waiting to be sent in the Outbox
folder.
You have missed calls.
Shown if Ringing type is set to Silent and Message
alert tone, IM alert tone, and E-mail alert tone are set
to Off.
The device keypad is locked.
A clock alarm is active.
The second phone line is being used (network service).
All calls to the device are forwarded to another
number. If you have two phone lines (network service), the
indicator for the first line is and for the second
.
A headset is connected to the device.
The connection to a headset with Bluetooth
connectivity has been lost.
A loopset is connected to the device.
A text phone is connected to the device.
A data call is active.
A GPRS or EDGE packet data connection is available.
A GPRS or EDGE packet data connection is active.
A GPRS or EDGE packet data connection is on hold.
A UMTS packet data connection is available.
A UMTS packet data connection is active.
A UMTS packet data connection is on hold.
You have set the device to scan for wireless LANs, and
a wireless LAN is available. See ‘Wireless LAN’, p. 101.
A wireless LAN connection is active in a network
that has encryption.
A wireless LAN connection is active in a network that
does not have encryption.
Bluetooth connectivity is on.
Data is being transmitted using Bluetooth
connectivity.
A USB connection is active.
Your Nokia N93
13
An infrared connection is active. If the indicator is
blinking, the device is trying to connect to the other
device or the connection has been lost.
Keypad lock (keyguard)
Use the keypad lock to prevent the keys from being
accidentally pressed.
Your Nokia N93
To turn on the display light when the keypad lock is on,
press the power key.
• To lock: In the standby mode, press , then .
When the keys are locked, is shown on the
display.
• To unlock in the Fold open mode: Press , then .
• To unlock in the Fold closed mode: Press the scroll key.
An unlock dialog appears on the cover display. Select
Yes by moving the scroll key.
When the keypad lock is on, calls may be possible to the
official emergency number programmed into your device.
Volume and loudspeaker control
To increase or decrease the
volume level when you have
an active call or are listening
to a sound, press or .
The built-in loudspeaker allows you to speak and listen
from a short distance without having to hold the device to
your ear.
Warning: Do not hold the device near your ear when
the loudspeaker is in use, because the volume may be
extremely loud.
To use the loudspeaker during a call, select Options >
Activate loudsp..
To turn off the loudspeaker, select Options > Activate
handset.
Clock
Press , and select Clock. To set a new alarm, select
Options > Set alarm. When an alarm is active, is
shown.
To turn off the alarm, select Stop, or to stop the alarm for
5 minutes, select Snooze.
If the alarm time is reached while the device is switched
off, the device switches itself on and starts sounding the
alarm tone. If you select Stop, the device asks whether you
want to activate the device for calls. Select No to switch
off the device or Yes to make and receive calls. Do not
14
FCC DRAFT
select Yes when wireless phone use may cause
interference or danger.
To cancel an alarm, select Clock > Options > Remove
alarm.
Clock settings
To change the clock settings, select Clock > Options >
Settings.
To change the time or date, select Time or Date.
To change the clock shown in the standby mode, select
Clock type > Analogue or Digital.
To allow the mobile phone network to update the time,
date, and time zone information to your device (network
service), select Network operator time > Auto-update.
To change the alarm tone, select Clock alarm tone.
World clock
To open the world clock view, open Clock, and press . In
the world clock view, you can view the time in different
cities.
To add cities to the list, select Options > Add city. You can
add a maximum of 15 cities to the list.
To set your current city, scroll to a city, and select
Options > My current city. The city is displayed in the
clock main view, and the time in your device is changed
according to the city selected. Check that the time is
correct and matches your time zone.
Headset
Connect a compatible
headset to the Pop-Port
connector of your device.
Warning: When
you use the headset, your
ability to hear outside
sounds may be affected.
Do not use the headset where it can endanger your safety.
TM
Wrist and lens cover straps
Thread the
straps as
shown, and
tighten them.
Wireless LAN
Your device supports wireless local area network (wireless
LAN). With wireless LAN, you can connect your device to
Your Nokia N93
15
the Internet and compatible devices that have wireless
LAN. For information about using your device in a home
network, see ‘Home network’, p. 17.
Some places, like France, have restrictions on the use of
wireless LAN. Check with your local authorities for more
information.
Features using wireless LAN, or allowing such features to
Your Nokia N93
run in the background while using other features, increase
the demand on battery power and reduce the battery life.
Your device supports the following wireless LAN features:
• IEEE 802.11b/g standard
• Operation at a frequency of 2.4 GHz
• Wired equivalent privacy (WEP) with keys up to 128
bits, Wi-Fi protected access (WPA), and 802.1x
encryption methods. These functions can be used only
if they are supported by the network.
You can create an Internet access point (IAP) in a wireless
LAN, and use it for applications that need to connect to
the Internet.
2 The device searches for wireless LANs within range.
Scroll to the network in which you want to create an
Internet access point, and select Options > Define
access point.
3 The device creates an Internet access point with default
settings. To view or change these settings, see ‘Access
points’, p. 98.
When an application asks you to select an access point,
select the created access point, or to search for wireless
LANs in range, select Search for WLAN.
A wireless LAN connection is established when you create
a data connection using a wireless LAN Internet access
point. The active wireless LAN connection ends when you
end the data connection. To end the connection, see
‘Connection manager’, p. 83.
You can use wireless LAN during a voice call or when
packet data is active. You can only be connected to one
wireless LAN access point device at a time, but several
applications can use the same wireless LAN connection.
When you activate the Offline profile, you can still use
wireless LAN (if available). Remember to comply with any
applicable safety requirements when establishing and
using a wireless LAN connection.
There are two operating modes in wireless LAN:
infrastructure and ad hoc.
The infrastructure operating mode allows two kinds of
communication: wireless devices are connected to each
other through a wireless LAN access point device, or
16
FCC DRAFT
wireless devices are connected to a wired LAN through a
wireless LAN access point device.
In the ad hoc operating mode, devices can send and receive
data directly with each other. To create an Internet access
point for the ad hoc network, see ‘Access points’, p. 98.
Tip! To check the unique media access control (MAC)
address that identifies your device, enter *#62209526#
in the standby mode.
Home network
Your device is compatible with Universal Plug and Play
(UPnP). With a wireless LAN access point device, you can
create a home network and connect compatible UPnP
devices that support wireless LAN to the network, such as
your Nokia N93, a compatible PC, a compatible printer, and
a compatible sound system or a TV, or a sound system or
TV equipped with a compatible wireless multimedia
receiver.
After you have configured the home network, you can
copy, view, or play compatible media files and print images
in Gallery on the other connected compatible devices, for
example, view images stored on your Nokia N93 on a
compatible TV. See ‘Home network’, p. 85 and ‘Image print’,
p. 37.
Copyright protections may prevent some images, music
(including ringing tones), and other content from being
copied, transferred, viewed, played, or printed.
To set up home networking in your wireless LAN, first
create and configure your wireless LAN home Internet
access point, then configure the devices. On your Nokia
N93, configure the settings in the Home network
application. To connect a compatible PC to the home
network, on the PC, you must install the Media Server
software from the DVD-ROM supplied with your Nokia
N93.
After you have completed the necessary configurations in
all devices connected to the network, you can start using
Home network to share your media files. See ‘View media
files’, p. 87.
The home network uses the security settings of the
wireless LAN connection. Use the home network feature in
a wireless LAN infrastructure network with a wireless LAN
access point device and encryption enabled.
Important: Always enable one of the available
encryption methods to increase the security of your
wireless LAN connection. Using encryption reduces the
risk of unauthorize access to your data.
Your device is connected to the home network only if you
accept a connection request from another device, or in
Gallery, select the option to view, play, print, or copy
Your Nokia N93
17
media files on your Nokia N93 or search for other devices
in the Home network folder.
Important security information
When you configure your wireless LAN home network,
enable an encryption method, first on your access point
device, then on the other devices you intend to connect to
Your Nokia N93
your home network. Refer to the documentation of the
devices. Keep any passcodes secret and in a safe place
separate from the devices.
To view or change the settings of the wireless LAN
Internet access point in your Nokia N93, see ‘Access
points’, p. 98.
If you use the ad hoc operating mode to create a home
network with a compatible device, enable one of the
encryption methods in WLAN security mode when you
configure the Internet access point. This step reduces the
risk of an unwanted party joining the ad hoc network.
Your device notifies you if another device attempts to
connect to it and the home network. Do not accept
connection requests from an unknown device.
If you use wireless LAN in a network that does not have
encryption, switch off sharing Nokia N93 files with other
devices, or do not share any private media files. To change
sharing settings, see ‘Home network settings’, p. 86.
Memory card
You can purchase a compatible miniSD
memory card and use it as extra storage
space to save the memory on your
device. You can also back up
information from your device to the memory card.
Use only compatible miniSD memory cards with this
device. Other memory cards, such as Reduced Size
MultiMediaCards, do not fit in the memory card slot and
are not compatible with this device. Using an incompatible
memory card may damage the memory card as well as the
device, and data stored on the incompatible card may be
corrupted.
Keep all memory cards out of the reach of small children.
Insert the memory card
1 To open the door of the
memory card slot,
swing it upwards in a
counterclockwise
direction.
18
FCC DRAFT
2 Insert the memory card
in the slot. Ensure that
the contact area on the
card is facing up.
3 Push the card in. You
hear a click when the card locks
into place.
4 Close the door. You cannot use the
memory card if the door is open.
Eject the memory card
1 Before you eject the card, press
the power key, and select Remove mem. card. All
applications are closed.
2 When Remove memory card and press 'OK' is
displayed, swing open the door of the memory card slot.
3 Press the memory card to release it from the slot.
4 Remove the memory card. If the device is switched on,
select OK when prompted to confirm the removal.
Important: Do not remove the memory card in the
middle of an operation when the card is being accessed.
Removing the card in the middle of an operation may
damage the memory card as well as the device, and data
stored on the card may be corrupted.
Memory card tool
Press , and select Tools > Memory. You can use a
miniSD memory card as extra storage space and for
backing up the information in the device memory.
To back up information from the device memory to a
memory card, select Options > Backup phone mem.
To restore information from the memory card to the device
memory, select Options > Restore from card.
Format a memory card
When a memory card is reformatted, all data on the card
is permanently lost.
Some memory cards are supplied preformatted and others
require formatting. Consult your retailer to find out if you
must format the memory card before you can use it.
To format a memory card, select Options > Format mem.
card. Select Yes to confirm.
Tip! For best performance, use your Nokia N93 to
format all new miniSD cards.
Your Nokia N93
19
File manager
select Options > Memory details. The amount of available
memory is shown in Free memory.
Your Nokia N93
20
Many features of the device, such as contacts, messages,
images, videos, ringing tones, calendar notes, documents,
and downloaded applications, use memory to store data.
The free memory available depends on how much data is
already saved in the device memory.
You can use a memory card as extra storage space.
Memory cards are rewritable, so you can delete old
information and save new data on a memory card.
To browse files and folders in the device memory or on a
memory card (if inserted), press , and select Tools > File
mgr.. The device memory view () opens. Press to
open the memory card view () (if available).
To move or copy files to a folder, press and at the
same time to mark a file, and select Options > Move to
folder or Copy to folder.
To find a file, select Options > Find and the memory from
which to search, and enter a search text that matches the
file name.
View memory consumption
To view what types of data you have in the device and
how much memory the different data types consume,
FCC DRAFT
Memory low—free memory
The device notifies you if the device or the memory card
memory is low.
To free device memory, transfer data to a memory card, if
you have one. Mark files to be moved, and select Move to
folder > Memory card and a folder.
You can also transfer media files to a compatible PC, for
example, using the transfer option in Gallery. See ‘Back up
files’, p. 38.
Tip! Use Nokia Phone Browser in Nokia PC Suite to
view the different memories in your device and transfer
data.
To remove data to free memory, use File mgr. or the
respective application. For example, you can remove the
following:
• Messages from the Inbox, Drafts, and Sent folders in
Messag.
• Retrieved e-mail messages from the device memory
• Saved Web pages
• Saved images, videos, or sound files
• Contact information
•Calendar notes
• Downloaded applications. See also ‘Application
manager’, p. 107.
• Any other data that you no longer need
Help
Your device has context-sensitive help. When an
application is open, select Options > Help to access help
for the current view.
When you are reading the instructions, to switch between
help and the application that is open in the background,
press and hold .
To open help from the main menu, select Tools > Help.
Select the desired application to view its help topics.
Tutorial
The tutorial gives you information about some of the
features of your device. To access the tutorial in the menu,
press , and select Extras > Tutorial and the section you
want to view.
Your Nokia N93
21
Camera
Camera
22
Your Nokia N93 has two cameras, a high resolution
camera on the side of the device (the main camera) and a
lower resolution camera on the top of the main display
(the secondary camera). You can use both cameras to take
still images and record video in the portrait and landscape
views.
The Nokia N93 device supports an image capture
resolution of 2048x1536 pixels using the main camera.
The image resolution in these materials may appear
different.
The images and video clips are automatically saved in the
Images & video folder in Gallery. The cameras produce
.jpeg images. Video clips are recorded in the .mp4 file
format, or in the 3GPP file format with the .3gp file
extension (Sharing modes). See ‘Video settings’, p. 23.
You can send images and video clips in a multimedia
message, as an e-mail attachment, or by using Bluetooth
connectivity.
Record videos
Activate the main camera by rotating the display to the
Imaging mode. If the camera is in the Image mode, use
the camera mode key to select Video mode.
FCC DRAFT
Press the capture key to start recording. The record icon
is shown. The red recording indicator flashes slowly
and a tone sounds, indicating that video is being recorded.
1 To pause recording at any time, press the capture key.
The pause icon () blinks on the display. Video
recording automatically stops if recording is set to
pause and there are no keypresses within a minute.
2 Press the capture key again to resume recording.
3 Select Stop to stop recording. The video clip is
automatically saved to the Images & video folder of
Gallery. See ‘Gallery’, p. 29.
To make lighting and color adjustments before recording a
video in the Imaging mode, use the side scroll key to scroll
through the toolbar. See ‘Setup settings—Adjust color and
lighting’, p. 27 and ‘Shooting modes’, p. 27.
To zoom in or out of the subject (continuous 3x optical and
up to 20x digital zoom), rotate the zoom key on the side of
the device.
The video viewfinder displays the following:
• Status
indicators (1)
for audio mute
on, stabilization
on, and the
current capture
mode.
• The toolbar (2),
which you can
scroll through
before
recording to select the shooting mode, white balance,
and color tone (the toolbar is not displayed during
recording).
• The total available video recording time (3). When you
are recording, the current video length indicator also
shows the elapsed time and time remaining.
• The device memory ( ) and memory card ( )
indicators (4) show where videos are saved.
• The video quality indicator (5) indicates whether the
quality of the video is TV (high), TV (normal), Handset
(high), Handset (normal), or Sharing.
• The video clip file type (6).
Tip! Select Options > Turn icons on to display all
viewfinder indicators or Turn icons off to display
only the video status indicators.
Exit
Options
After you record a video clip, select the following from the
toolbar:
• To immediately play the video clip you just recorded,
select Play.
• If you do not want to keep the video, select Delete.
• To send the video using multimedia, e-mail, Bluetooth,
or infrared, press the call key, or select Send. For more
information, see ‘Messaging’, p. 39 and ‘Bluetooth
connectivity’, p. 79. This option is not available during
an active call. You cannot send video clips saved in the
.mp4 file format in a multimedia message.
• To record a new video clip, select New video.
Tip! Activate the Offline profile to ensure your video
recording is not interrupted by incoming calls or
messages.
Video settings
There are two kinds of settings for the video recorder:
Video setup and main settings. To adjust Video setup, see
‘Setup settings—Adjust color and lighting’, p. 27. The
setup settings return to the default settings after you
close the camera, but the main settings remain the same
until you change them again. To change the main settings,
select Options > Settings and from the following:
Audio recording—Select On if you want to record sound.
Camera
23
Video quality—Set the quality of the video clip to TV
(high) (best quality for long term usage and playback on
a compatible TV or PC and handset), TV (normal),
Handset (high), Handset (normal), or Sharing (limited
Camera
video clip size to send using multimedia message (MMS)).
If you want to view the video on a TV or PC, select TV
(high), which has VGA resolution (640x480) and the .mp4
file format. To send the video clip through MMS, select
Sharing (QCIF resolution, .3gp file format). The size of the
video clip recorded with Sharing is limited to 300 KB
(about 20 seconds in duration) so that it can be
conveniently sent as a multimedia message to a
compatible device.
Video stabilisation—Select On to reduce camera shake
when recording the video.
Add to album—Select whether you want to add the
recorded video clip to a certain album in Gallery. Select
Yes to open a list of available albums.
Show captured video—Select whether you want the first
frame of the recorded video clip to be shown on the
display after the recording stops. Select Play from the
toolbar (main camera) or Options > Play (secondary
camera) to view the video clip.
Optical zoom during recording—Select On or Off. Select
Off to eliminate mechanical noise caused by lens
movement during optical zooming when recording.
Memory in use—Define the default memory store: device
memory or memory card (if inserted).
Take pictures
Activate the main camera by rotating the display to
Imaging mode. If the camera is in video mode, use the
camera mode key to switch to image mode.
To lock the focus on an object, press the capture key
halfway down (main camera only). The green locked focus
indicator appears on the display. If the focus was not
locked, the red focus indicator appears. Release the
capture key, and press it halfway down again. You can,
however, take the picture without locking the focus.
To take a picture, in the main camera, press the capture
key. Do not move the device before the image is saved.
You can make lighting and color adjustments before taking
a picture in the Imaging mode by using the side scroll key
to scroll through the toolbar. See ‘Setup settings—Adjust
color and lighting’, p. 27.
Saving the captured image may take longer if you change
the zoom, lighting, or color settings.
The camera viewfinder displays the following:
24
FCC DRAFT
• Status
indicators (1)
for sequence
on, self-timer
on; Automatic
(), On (),
or Off ()
flash mode, and
the current
capture mode.
• The toolbar (2), which you can scroll through before
capturing the image to select the shooting mode, white
balance, exposure value, and color tone (the toolbar is
not displayed during focus and image capture).
• The image resolution indicator (3) indicates whether
the quality of the image is Print 3M - Large
(2048x1536 resolution), Print 2M - Med. (1600x1200
resolution), Print 1.3M - Small (1280x960 resolution),
or MMS 0.3M (640x480 resolution).
• The image counter (4) displays the estimated number of
images you can capture using the current image quality
setting and memory in use (the counter is not displayed
during focus and image capture).
• The device memory ( ) and memory card ( )
indicators (5) show where images are saved.
Tip! Select Options > Turn icons on to display all
viewfinder indicators or Turn icons off to display
only the camera status indicators.
Exit
Options
When taking a picture, note the following:
• Use both hands to keep the camera still.
• The quality of a digitally zoomed picture is lower than
that of a nonzoomed picture.
• The camera goes into the battery saving mode if there
are no keypresses for a moment. To continue taking
pictures, press .
After you take the picture, select the following from the
toolbar:
• If you do not want to keep the image, select Delete.
• To send the video using multimedia, e-mail, Bluetooth,
or infrared, press the call key, or select Send.
• To capture a new image, select New image.
• To print the picture, select Print. See ‘Image print’,
p. 37.
Still image camera settings
There are two kinds of settings for the still image camera:
Image setup and main settings. To adjust Image setup,
see ‘Setup settings—Adjust color and lighting’, p. 27. The
setup settings return to the default settings after you
close the camera, but the main settings remain the same
until you change them again. To change the main settings,
select Options > Settings and from the following:
0.3M (640x480 resolution). The better the image quality,
the more memory the image consumes. If you want to
print the image, select Print 3M - Large, Print 2M -
Camera
Med., or Print 1.3M - Small. If you want to send it
through e-mail, select Print 1.3M - Small. To send the
image through MMS, select MMS 0.3M.
These resolutions are only available in the main camera.
Add to album—Select whether you want to save the
image to a certain album in the gallery. If you select Yes,
a list of available albums opens.
Show captured image—Select Yes if you want to see the
captured image after it is taken, or No if you want to
continue taking pictures right away.
Extended zoom (main camera only)—Select On
(continuous) to allow the zoom increments to be smooth
and continuous between digital and extended digital
zoom, On (paused) to allow the zoom increments to
pause at the digital and extended digital step point. If you
want to limit the zoom to where the selected image
quality is maintained, select Off.
Flicker cancellation—Select 50Hz or 60Hz.
Shutter tone—Select the tone you want to hear when you
take a picture.
Memory in use—Select where to store your images.
Take pictures in a sequence
Sequence mode is available only in the main camera.
To set the camera to take up to six pictures in a sequence
(if enough memory available), select Options > Sequence
mode.
To take the pictures, press the capture key.
After you take the pictures, they are shown in a grid on the
display. To view a picture, press to open it.
You can also use the sequence mode with the self-timer.
To return to the sequence mode viewfinder, press the
capture key.
You in the picture—self-timer
The self-timer is available only in the main camera.
Use the self-timer to delay the capture so that you can
include yourself in the picture. To set the self-timer delay,
select Options > Self timer > 2 seconds, 10 seconds, or
20 seconds. To activate the self-timer, select Activate. The
self-timer indicator () blinks and the device beeps when
the timer is running. The camera takes the picture after the
selected delay elapses.
You can also use the self-timer in the sequence mode.
Keep a safe distance when using the flash. Do not use the
flash on people or animals at close range. Do not cover the
flash while taking a picture.
The camera has an LED flash for low light conditions. The
following flash modes are available: Automatic (), On
(), and Off ().
To switch between the flash modes, press the flash key.
Setup settings—Adjust color and
lighting
To enable the camera to reproduce colors and lighting
more accurately, or to add effects to your pictures or
videos, use the side scroll key to scroll through the toolbar,
and select from the following options:
Shooting mode—Select a proper shooting mode for the
environment in which you take pictures. Every shooting
mode uses its own lighting settings that have been
adjusted according to a certain kind of environment.
White balance—Select the current lighting condition
from the list. This allows the camera to reproduce colors
more accurately.
Exposure value (images only)—Adjust the exposure time
of the camera.
Colour tone—Select a color effect from the list.
The screen display changes to match any settings you
make, so that you see how the change affects the pictures
or videos.
The available settings vary depending on the selected
camera.
The setup settings are camera specific; if you change the
settings in the secondary camera, the settings in the main
camera do not change. The setup settings do, however,
transfer between the image and video modes.
Shooting modes
A shooting mode helps you to find the right color and
lighting settings for the current environment. Select a
proper shooting mode for taking pictures or recording
video clips from the shooting mode list. The settings of
each shooting mode have been set according to a certain
style or environment.
Shooting modes are only available in the main camera.
Camera
27
Use the side scroll key to scroll through the toolbar, and
select from the following options:
Video shooting modes
Camera
Normal ()(default) and Night ()
Image shooting modes
Automatic () (default), User (), Close-up mode
(), Landscape (), Night (), and Night portrait
().
When you take pictures, the default shooting mode is
Automatic.
To make your own shooting mode suitable for a certain
environment, scroll to User, and select Options > Change.
In the user defined shooting mode you can adjust
different lighting and color settings. To copy the settings
of another shooting mode, select Based on shooting
mode and the desired shooting mode.
28
FCC DRAFT
Gallery
To store and organize your images, video clips, sound clips,
playlists, and streaming links, or share your files with other
compatible Universal Plug and Play devices through
wireless LAN, press , and select Gallery. To open the
gallery from the Camera application, select Options > Go
to Gallery. From Camera, only the Images & video folder
is available.
Tip! To switch from Gallery to the camera, in the
Images & video folder, press the capture key or the camera
mode key, or select Options > Go to Camera.
Select Images & video , Tracks , Sound clips ,
Streaming links , Presentations , All files , or
Home network, and press to open it.
Video clips, .ram files, and streaming links are opened and
played in the RealPlayer application. See ‘RealPlayer’,
p. 73. You can also create albums; and mark, and add items
to albums. See ‘Albums’, p. 34.
To open a file, press . Videos open in RealPlyr., and
music and sound clips in Mus. plyr.. See ‘View images and
video clips’, p. 30.
To copy or move files to the memory card (if inserted) or to
device memory, select a file and Options > Move and
copy > Copy to memory card/Move to memory card or
Copy to phone mem./Move to phone mem..
Files stored on the memory card (if inserted) are indicated
with . Files stored on the memory card (if inserted) are
indicated with .
To reduce the size of images that you already copied to
other locations, such as to a compatible PC, select
Options > Transfer & memory > Shrink. Selecting
Shrink reduces the resolution of an image to 640x480. To
increase free memory space after you have copied items to
other locations or devices, select a file and Options > Free
memory. See ‘Back up files’, p. 38.
To download files into Gallery in one of the main folders
using the browser, select Graphic downl., Video downl.,
Track downl.
you can select a bookmark from which the site can
download.
To share media files saved in Gallery with other
compatible UPnP devices through wireless LAN, you must
first create and configure your wireless LAN home Internet
access point, and then configure the Home network
application. See ‘Wireless LAN’, p. 15.
, or Sound downl.. The browser opens, and
FCC DRAFT
Gallery
29
The options related to Home network are not available in
Gallery before the Home network settings have been
configured.
Gallery
View images and video clips
Pictures taken and video clips recorded with the camera
are stored in the Images & video folder in Gallery. Images
and video clips can also be sent to you in a multimedia
message, as an e-mail attachment, through Bluetooth
connectivity, or by using infrared. To be able to view a
received image or video clip in the gallery or in the media
player, you must save it in the device memory or on a
memory card (if inserted).
Open the Images & video folder in Gallery. The images
and video clip files are in a loop, and ordered by date. The
number of files is displayed. To browse the files one by
one, scroll left or right. To browse files in groups, scroll up
or down.
To edit a video clip or a photo, select Options > Edit. An
image editor or a video editor opens. See ‘Edit video clips’,
p. 30. See ‘Edit images’, p. 32.
To add an image or a video clip to an album in the gallery,
select Options > Albums > Add to album. See ‘Albums’,
p. 34.
To create custom video clips, select a video clip or several
clips in the gallery, and select Options > Edit. See ‘Edit
video clips’, p. 30.
To print your images on a compatible printer, or to store
them on your memory card (if inserted) for printing, select
Options > Print. See ‘Image print’, p. 37.
To send a multimedia message to your service provider's
media file uploading service (network service), press the
call key, and select Via MMS upload (if available). Contact
your service provider for more information.
To view the image, scroll to an image and press .
When the image is opened, to zoom an image, select
Options > Zoom in or Zoom out. The zooming ratio is at
the top of the display. The zooming ratio is not stored
permanently.
To use the picture as a background image, select the
picture and Options > Assign > Set as wallpaper.
To delete an image or video clip, press .
Edit video clips
To edit video clips in Gallery and create custom video clips,
scroll to a video clip, and select Options >Edit. See
‘Gallery’, p. 29. To create custom video clips, combine and
trim video clips, and add images, sound clips, transitions,
30
and effects. Transitions are visual effects that you can add
in the beginning and end of the video or between the video
clips.
You can also use Movie director to create custom video
clips. Select the video clips and images you want to create
a muvee with and select Options > Edit > Create muvee.
See ‘Movie director’, p. 76.
In the video editor you can see two timelines: video clip
timeline and sound clip timeline. The images, text, and
transitions added to a video clip are shown on the video
clip timeline. To switch between the timelines, scroll up or
down.
Edit video, sound, image, text, and
transitions
To create custom video clips, mark and select one or more
video clips, and select Options > Edit.
To modify the video, select from the following options:
Edit video clip:
Cut—Trims the video clip in the cut video clip view.
Add color effect—Inserts a color effect on the video clip.
Use slow motion—Slows the speed of the video clip.
Mute sound/Unmute sound—Mutes or unmutes the
original video clip sound.
Move—Moves the video clip to the selected location.
Remove—Removes the video clip from the video.
Duplicate—Makes a copy of the selected video clip.
Edit text (shown only if you added text)—To move,
remove, or duplicate text; change the color and style of
the text; define how long it stays on the screen; and add
effects to the text.
Edit image (shown only if you added an image)—To move,
remove, or duplicate an image; define how long it stays on
the screen; and set a background or a color effect to the
image.
Edit sound clip (shown only if you have added a sound
clip)—To cut or move the sound clip, to adjust its length,
or to remove or duplicate the clip.
Edit transition—There are three types of transitions: at
the start of a video, at the end of a video, and transitions
between video clips. You can select start transition when
the first transition of the video is active.
Insert—Select Video clip, Image, Text, Sound clip, or New
sound clip.
Movie—Preview the movie in the full screen or as a
thumbnail, save or send the movie, or cut the movie to a
proper size for sending it in a multimedia message.
Gallery
FCC DRAFT
31
To take a snapshot of a video clip, in the cut video view,
select Options > Take snapshot. In the thumbnail
preview view, press , and select Take snapshot.
Gallery
To save your video, select Options > Movie > Save. To
define the Memory in use, select Options > Settings. The
default is the device memory.
In the Settings view, you can also define Default video
name, Default sc. shot name, Resolution, and Memory
in use.
To send the video, select Send > Via multimedia,
Via e-mail, Via Bluetooth, or Via infrared. Contact your
network operator or service provider for details of the
maximum multimedia message size that you can send. If
your video is too large to send in a multimedia message,
appears.
Tip! If you want to send a video clip that is over the
maximum multimedia message size allowed by your
service provider, you can send the clip using Bluetooth
wireless technology. See ‘Send data using Bluetooth
connectivity’, p. 81. You can also transfer your videos to a
compatible PC using Bluetooth connectivity, or by using a
memory card reader enhancement.
Edit images
To edit the pictures after taking them, or the ones already
saved in Gallery, select Options > Edit.
Select Apply effect to crop and rotate the image; adjust
the brightness, color, contrast, and resolution; and add
effects, text, clip art, or a frame to the picture.
To crop an image, select Options > Apply effect > Crop.
To crop the image size manually, select Manual or a
predefined aspect ratio from the list. If you select Manual,
a cross appears in the upper left corner of the image. Move
the scroll key to select the area to crop, and select Set.
Another cross appears in the lower right corner. Again
select the area to be cropped. To adjust the first selected
area, select Back. The selected areas form a rectangle,
which forms the cropped image.
If you selected a predefined aspect ratio, select the upper
left corner of the area to be cropped. To resize the
highlighted area, use the scroll key. To freeze the selected
area, press . To move the area within the picture, use
the scroll key. To select the area to be cropped, press .
To reduce redness of the eyes in an image, select Options >
Apply effect > Red eye redu.. Move the cross onto the
eye, and press . A loop appears on the display. To resize
the loop to fit the size of the eye, move the scroll key. To
reduce the redness, press .
32
Shortcuts in the image editor:
• To view an image in the full screen, press . To return
to the normal view, press again.
• To rotate an image clockwise or counterclockwise,
press or .
• To zoom in or out, press or .
• To move on a zoomed image, scroll up, down, left, or
right.
Slide show
Select Options > Slide show > Start to view images and
video clips in the full screen mode. The slide show starts
from the selected file. Select from the following:
• Play—to open the RealPlayer application, and play a
selected video clip
• Pause—to pause the slide show
• Continue—to resume the slide show, if paused
• End—to close the slide show
To browse the images, press (previous) or (next).
To adjust the tempo of the slide show, before starting the
slide show, select Options> Slide show > Settings >
Delay between slides.
To add sound to the slide show, select Options > Slide
show > Settings and from the following:
• Music—Select On or Off.
• Track—Select a music file from the list.
To decrease or increase the volume during the slide show,
press or .
TV out mode
You can watch videos and images stored in your device on
the screen of a compatible TV. Connect the Nokia
Video-Out Cable (CA-64U) from the TV out Pop-Port
connector on your device to the video input of a
compatible TV. For all applications other than the Images
& video folder in Gallery and RealPlyr., the TV screen
displays what is displayed on the screen of your device.
When you open an image in the thumbnail view while it is
viewed on the TV, the Zoom in option is not available.
When image is not zoomed, the opened image is displayed
on the TV in full screen.
You can view videos and images as a slide show. All items
in an album or marked videos and images are displayed on
the TV in full screen while the selected music plays.
When you open a highlighted video clip, RealPlyr. starts
playing the video clip on the device display and the TV
screen. See ‘RealPlayer’, p. 73.
All audio, including the stereo video clip sound, ringing
tone, and key tone, is routed to the TV when the Nokia
Gallery
FCC DRAFT
33
Video-Out Cable is connected to the device. You can use
the device microphone normally.
TV out settings must be configured for the applicable TV
Gallery
system and TV aspect ratio. See ‘TV configuration’, p. 97.
Presentations
With presentations, you can view SVG (scalable vector
graphics) files, such as cartoons and maps. SVG images
maintain their appearance when printed or viewed with
different screen sizes and resolutions. To view SVG files,
select the Presentations folder, scroll to an image, and
select Options > Play.
To zoom in, press . To zoom out, press .
To switch between full screen and normal screen, press *.
Albums
With albums you can conveniently manage your images
and video clips. To view the albums list, in the Images &
video folder, select Options > Albums > View albums.
To add a picture or a video clip to an album in the gallery,
scroll to a picture or video clip, and select Options >
Albums > Add to album. A list of albums opens. Select
the album to which you want to add the picture or video
clip, and press .
To remove a file from an album, press . The file is not
deleted from the Images & video folder in Gallery.
Online album (network service)
Online album allows you to manage your images and
videos online. You can view, edit, upload, and rename
albums and their contents. You must first set the required
settings to connect to the service. Contact your network
operator/service provider for details. In the Images & video
folder, select Options > Online services > Open service.
When you open the service, the List view displays the
albums/entries and the details in the selection list in
chronological order. If the item is a video clip, then the first
frame of the clip is displayed.
When you open an online entry the Images view is
displayed and the content of the entry is refreshed from
the server. The view shows the entry name and description
(if this information was entered). You can play the video
clip or view the thumbnail image.
To add or edit the name and description text, and upload
the entry content to the server, open the Images & video
folder in Gallery. Scroll to a picture or video clip, and select
Options > Edit .
To add an image or a video clip to the server, scroll to the
image or video clip, select Options > Online services, and
34
after the service is opened, select Options > Upload. You
can also upload albums and their contents by selecting
Options > Send.
Online print (network service)
In the Images & video folder, select the images you want
to order using PrintOnline, and then select Options >
Print > Order prints. You must first set the required
settings to connect to the service. Contact your network
operator or service provider for details.
The images are displayed in a preview, and you can set the
number of copies, the product and product type for the
images, your presonal information, delivery information,
payment method, and view the status of your orders in the
log.
Gallery
FCC DRAFT
35
Media applications
36
Music player
Press , and select Mus. plyr.. With the music player,
you can play music files and create and listen to playlists.
Media applications
Warning: Listen to music at a moderate level.
Continuous exposure to high volume may damage your
hearing. Do not hold the device near your ear when the
loudspeaker is in use, because the volume may be
extremely loud.
Add music
When you open the music player for the first time, the
player searches the device memory for music files to
create a music library.
After you add or remove music files in the device, update
your music library. Select Options > Music library >
Options > Update Music library.
Tip! You can transfer music files from your device to
a compatible memory card (if inserted) with Nokia
Audio Manager available in Nokia PC Suite.
Play music
When you open the music player, the previously played
track or playlist is displayed. To view the music library,
select or Options > Music library and the desired song
list. To start playing the songs in the view, select Options >
Play.
When a song is playing, to change between play and pause,
press or .
To stop a song, press . To fast forward or rewind, press
and hold or . To start playing the next or previous
song, press or .
To view the currently played song list, select or
Options > Open 'Now playing'. To save the song list as a
playlist, select Options > Add to track list, and create a
new playlist, or select a saved playlist.
To adjust the volume, press or .
To modify the tone of music playback, select Options >
Equaliser.
To select between random play and normal play mode,
select Options > Random play. To select whether playing
stops at the end of the playlist or restarts from its
beginning, select Options > Loop.
To open your Web bookmarks for downloading music,
select Options > Track downloads.
To return to the standby mode and leave the music playing
in the background, select Options > Play in background.
Music library
To view the music library, select Options > Music library.
All tracks lists all music. To view sorted songs, select
Albums, Artists, Genres, or Composers. The album, artist,
genre, and composer information is collected from the ID3
or M4A tags of the song files, if available.
To add songs, albums, artists, genres, or composers to a
playlist, select the items and Options > Add to track list.
You can create a new playlist or add to an existing one.
To view playlists, select Track lists. To create a new
playlist, select Options > New track list. When viewing a
playlist you have created yourself, to add more songs,
select Options > Add tracks.
To delete a playlist, press . Deleting a playlist only
deletes the playlist, not the music files.
Image print
Use Image print to print your images using a data cable,
wireless LAN (if available), Bluetooth connectivity, or a
compatible memory card (if available).
You can only print images that are in .jpeg format. The
pictures taken with the camera are automatically saved in
.jpeg format.
To print images with Image print, select the image you
want to print, and the print option in the gallery, camera,
image editor, or image viewer.
To print to a printer compatible with Image print, connect
the data cable before you select the print option.
Printer selection
When you use Image print for the first time, a list of
available printers is displayed after you select the image.
Select a printer. The printer is set as the default printer.
If you have connected a printer compatible with Image
print using the CA-53 cable, the printer is automatically
displayed.
If the default printer is not available, a list of available
printing devices is displayed.
To change the default printer, select Options > Print
settings > Default printer.
Media applications
FCC DRAFT
37
Print preview
The print preview view opens only when you start printing
an image in the gallery.
The selected images are displayed using predefined
layouts. To change the layout, scroll left and right through
the available layouts for the selected printer. If the images
do not fit on a single page, scroll up or down to display the
additional pages.
Media applications
Print settings
The available options vary, depending on the capabilities
of the printing device you selected.
To set a default printer, select Options > Default printer.
To select the paper size, select Paper size, the size of
paper from the list, and OK. Select Cancel to return to the
previous view.
Back up files
To transfer and back up media files from your device to a
compatible PC through the wireless LAN, select Options >
Transfer > Start. See ‘Wireless LAN’, p. 15.
Your device starts a device search. Select a device and a
folder to which you want to transfer the media files.
Select OK.
To change the Storage device or Store in folder settings,
select Options > Settings.
38
Messaging
Press , and select Messag.. In Messag., you can create,
send, receive, view, edit, and organize text messages,
multimedia messages, e-mail messages, and special text
messages containing data. You can also receive messages
and data using Bluetooth connectivity or infrared, receive
Web service messages, cell broadcast messages, and send
service commands.
To create a new message, select New message.
Note: Only devices that have compatible features
can receive and display multimedia messages. The
appearance of a message may vary depending on the
receiving device.
Messag. contains the following folders:
Inbox—Received messages, except e-mail and cell
broadcast messages, are stored here. E-mail messages are
stored in the Mailbox.
My folders—Organize your messages into folders.
Tip! To avoid rewriting messages that you send often,
use texts in the templates folder.
Mailbox—Connect to your remote mailbox to retrieve
your new e-mail messages or view your previously
retrieved e-mail messages offline. See ‘E-mail’, p. 49.
Drafts—Draft messages that have not been sent are
stored here.
Sent—The last 20 messages that have been sent,
excluding messages sent using Bluetooth connectivity or
infrared, are stored here. To change the number of
messages to be saved, see ‘Other settings’, p. 51.
Outbox—Messages waiting to be sent are temporarily
stored here.
Example: Messages are placed in the outbox, for
example, when your device is outside network
coverage. You can also schedule e-mail messages to be
sent the next time you connect to your remote
mailbox.
Reports—You can request the network to send you a
delivery report of the text messages and multimedia
messages you have sent (network service). Receiving a
delivery report of a multimedia message that has been
sent to an e-mail address may not be possible.
Tip! When you have opened any of the default
folders, to switch between the folders, press or .
To enter and send service requests (also known as USSD
commands), such as activation commands for network
FCC DRAFT
Messaging
39
services, to your service provider, select Options >
Service command in the main view of Messag..
Cell broadcast (network service) allows you to receive
messages on various topics, such as weather or traffic
conditions from your service provider. For available topics
Messaging
and relevant topic numbers, contact your service provider.
In the main view of Messaging, select Options > Cell
broadcast. In the main view, you can see the status of a
topic, a topic number, name, and whether it has been
flagged ( ) for follow-up.
Cell broadcast messages cannot be received in UMTS
networks. A packet data connection may prevent cell
broadcast reception.
Write text
ABC, abc, and Abc indicate the selected character mode.
123 indicates the number mode.
Traditional text input
is displayed when you are writing text using
traditional text input.
• Press a number key (—) repeatedly until the
desired character appears. There are more characters
available for a number key than are printed on the key.
• If the next letter is located on the same key as the
present one, wait until the cursor appears (or press
to end the time-out period), and enter the letter.
• To insert a space, press . To move the cursor to the
next line, press three times.
Predictive text input
You can enter any letter with a single keypress. Predictive
text input is based on a built-in dictionary to which you
can add new words. is displayed when you write
text using predictive text input.
1 To activate predictive text input, press , and select
Predictive text on. This activates predictive text input
for all editors in the device.
2 To write the desired word,
press the keys —.
Press each key only once
for one letter. For
example, to write "Nokia"
when the English
dictionary is selected,
press for N, for o,
for k, for i, and
for a.
The word suggestion changes after each keypress.
3 When you finish writing the word correctly, press
to confirm it, or press to add a space.
40
If the word is not correct, press repeatedly to view
the matching words the dictionary has found one by
one, or press , and select Predictive text >
Matches.
If the ? character is shown after the word, the word is
not in the dictionary. To add a word to the dictionary,
select Spell, enter the word using traditional text input,
and select OK. The word is added to the dictionary.
When the dictionary is full, a new word replaces the
oldest added word.
4 Start writing the next word.
Write compound words
Write the first half of a compound word; to confirm it,
press . Write the last part of the compound word. To
complete the compound word, press to add a space.
Turn predictive text input off
To turn predictive text input off for all editors in the device,
press , and select Predictive text > Off.
Tip! To turn predictive text input on or off, quickly
press twice.
Tips on text input
To insert a number in the letter mode, press and hold the
desired number key.
To switch between the letter and number mode, press and
hold .
To switch between the different character modes, press
.
To delete a character, press . To delete more than one
character, press and hold .
The most common punctuation marks are available under
.
To open a list of special characters, press and hold .
Tip! To insert several special characters at the same
time, press when you select each character.
Write and send messages
The appearance of a multimedia message may vary,
depending on the receiving device.
Copyright protections may prevent some images, music
(including ringing tones), and other content from being
copied, modified, transferred or forwarded.
Before you can create a multimedia message or write an
e-mail, you must have the correct connection settings in
place. See ‘Receive MMS and e-mail settings’, p. 43 and
‘E-mail’, p. 49.
Messaging
FCC DRAFT
41
The wireless network may limit the size of MMS messages.
If the inserted picture exceeds this limit, the device may
make it smaller so that it can be sent by MMS.
1 Select New message and one of the following:
Messaging
Text msg.—to send a text message
Multimedia message—to send a multimedia message
(MMS)
E-mail—to send an e-mail
If you have not set up your e-mail account, you are
prompted to do so. To start creating the e-mail
settings with the mailbox guide, select Start.
2 In the To field, press
to select recipients or
groups from contacts, or
enter the recipient’s
phone number or e-mail
address. To add a
semicolon (;) that
separates the recipients,
press . You can also
copy and paste the
number or address from
the clipboard.
3 In the Subject field, enter the subject of a multimedia
message or e-mail. To change the fields that are
visible, select Options > Address fields.
4 In the message field, write the message. To insert a
template, select Options > Insert or Insert object >
Template.
5 To add a media object to a multimedia message, select
Options > Insert object > Image, Sound clip, or Video
clip. When sound is added, is shown.
To change the format in which recorded videos are
saved, see ‘Video settings’, p. 23.
6 To take a new picture or record sound or video for a
multimedia message, select Insert new > Image,
Sound clip, or Video clip. To insert a new slide to the
message, select Slide.
To see what the multimedia message looks like, select
Options > Preview.
7 To add an attachment to an e-mail, select Options >
Insert > Image, Sound clip, Video clip, or Note. E-mail
attachments are indicated by .
Tip! To send other file types as attachments, open
the appropriate application, and select Send > Via
e-mail, if available.
8 To send the message, select Options > Send, or press
.
Your device supports the sending of text messages beyond
the character limit for a single message. Longer messages
are sent as a series of two or more messages. Your service
provider may charge accordingly. Characters that use
accents or other marks, and characters from some
42
language options like Chinese, take up more space limiting
the number of characters that can be sent in a single
message. In the navigation bar, you can see the message
length indicator counting backwards. For example, 10 (2)
means that you can still add 10 characters for the text to
be sent as two messages.
E-mail messages are automatically placed in Outbox
before sending. If sending does not succeed, the e-mail is
left in the Outbox with the Failed status.
Tip! You can combine images, video, sound, and text
to a presentation and send it in a multimedia message.
Start to create a multimedia message, and select
Options > Create presentation. The option is shown
only if MMS creation mode is set to Guided or Free.
See ‘Multimedia messages’, p. 48.
Receive MMS and e-mail settings
You may receive the settings in a message from your
network operator or service provider. See ‘Data and
settings’, p. 44.
For availability of and subscription to data services,
contact your network operator or service provider. Follow
the instructions given by your service provider.
multimedia messaging access point. See ‘Connection’,
p. 98.
2 Press , and select Messaging > Options >
Settings > Multim. msg. > Access point in use and
the access point you created as the preferred
connection. See also ‘Multimedia messages’, p. 48.
Before you can send, receive, retrieve, reply to, and
forward e-mail, you must do the following:
• Configure an Internet access point (IAP) correctly. See
‘Connection’, p. 98.
• Define your e-mail settings correctly. If you select
Mailbox in the Messag. main view and have not set up
your e-mail account, you are prompted to do so. To
start creating the e-mail settings with the mailbox
guide, select Start. See also ‘E-mail’, p. 49.
You must have a separate e-mail account. Follow the
instructions given by your remote mailbox and Internet
service provider (ISP).
Inbox—receive messages
In the Inbox folder, indicates an unread text
message, an unread multimedia message, data
Messaging
FCC DRAFT
43
received through infrared, and data received through
Bluetooth connectivity.
When you receive a message, and 1 new message
are shown in the standby mode. to open the message,
select Show. To open a message in Inbox, scroll to it, and
Messaging
press .
To reply to a received message, select Options > Reply.
To print a text or a multimedia message on a compatible
Basic Print Profile (BPP) equipped printer with Bluetooth
connectivity (such as HP Deskjet 450 Mobile Printer or HP
Photosmart 8150), select Options > Print.
Multimedia messages
Important: Exercise caution when opening
messages. Multimedia message objects may contain
malicious software or otherwise be harmful to your device
or PC.
You may receive a notification that a multimedia message
is waiting in the multimedia message center. To start a
packet data connection to retrieve the message to your
device, select Options > Retrieve.
When you open a multimedia message (), you may see
an image and a message. is shown if sound is
included, or if video is included. To play the sound or
the video, select the indicator.
To see the media objects that have been included in the
multimedia message, select Options > Objects.
If the message includes a multimedia presentation, is
displayed. To play the presentation, select the indicator.
Data and settings
Your device can receive many kinds of messages that
contain data ():
Configuration message—You may receive settings from
your network operator, service provider, or company
information management department in a configuration
message. To save the settings, select Options > Save all.
Business card—To save the information to Contacts, select
Options > Save business card. Certificates or sound files
attached to the business card are not saved.
Ringing tone—To save the ringing tone, select Options >
Save.
Operat. logo—To have the logo shown in the standby
mode instead of the network operator’s own identification,
select Options > Save.
Calen. entry—To save the invitation, select Options >
Save to Calendar.
Web message—To save the bookmark to the bookmarks
list in Web, select Options > Add to bookmarks. If the
44
message contains both access point settings and
bookmarks, to save the data, select Options > Save all.
E-mail notif.—The note tells you how many new e-mails
you have in your remote mailbox. An extended notification
may list more detailed information.
Web service messages
Web service messages () are notifications (for example,
news headlines) and may contain a text message or a link.
For availability and subscription, contact your service
provider.
Open the mailbox
When you open the mailbox, the device asks if you want
to connect to the mailbox (Connect to mailbox?).
To connect to your mailbox and retrieve new e-mail
headings or messages, select Yes. When you view
messages online, you are continuously connected to a
remote mailbox using a data connection. See also
‘Connection’, p. 98.
To view previously retrieved e-mail messages offline,
select No. When you view e-mail messages offline, your
device is not connected to the remote mailbox.
Messaging
Mailbox
If you select Mailbox and have not set up your e-mail
account, you are prompted to do so. To start creating the
e-mail settings with the mailbox guide, select Start. See
also ‘E-mail’, p. 49.
When you create a new mailbox, the name you give to the
mailbox replaces Mailbox in the Messaging main view.
You can have up to six mailboxes.
Retrieve e-mail messages
If you are offline, select Options > Connect to start a
connection to the remote mailbox.
Important: Exercise caution when opening
messages. E-mail messages may contain malicious
software or otherwise be harmful to your device or PC.
1 When you have an open connection to a remote
mailbox, select Options > Retrieve e-mail and one of
the following:
New—to retrieve all new e-mail messages
Selected—to retrieve only the e-mail messages that
have been marked
All—to retrieve all messages from the mailbox
FCC DRAFT
45
To stop retrieving messages, select Cancel.
2 After you retrieve the e-mail messages, you can
continue viewing them online, or select Options >
Disconnect to close the connection and view the
Messaging
e-mail messages offline.
E-mail status indicators:
The new e-mail (offline or online mode) has not
been retrieved to your device.
The new e-mail has been retrieved to your device.
The e-mail message has been read, and it has not
been retrieved to your device.
The e-mail message has been read.
The e-mail heading has been read and the
message content has been deleted from the device.
3 To open an e-mail message, press . If the e-mail
message has not been retrieved and you are offline,
you are asked if you want to retrieve this message
from the mailbox.
To view e-mail attachments, open a message that has the
attachment indicator , and select Options >
Attachments. If the attachment has a dimmed indicator,
it has not been retrieved to the device; select Options >
Retrieve.
You can also receive meeting requests in the mailbox. See
‘Meeting requests’, p. 69, and ‘Create calendar entries’,
p. 69.
To print an e-mail message on a compatible Basic Print
Profile (BPP) equipped printer with Bluetooth connectivity
(such as HP Deskjet 450 Mobile Printer or HP Photosmart
8150), select Options > Print.
Retrieve e-mail messages automatically
To retrieve messages automatically, select Options >
E-mail settings > Automatic retrieval > Header
retrieval > Always enabled or Only in home net., and
define when and how often the messages are retrieved.
Retrieving e-mail messages automatically may increase
your call costs due to the data traffic.
Delete e-mail messages
To delete the contents of an e-mail message from the
device while still retaining it in the remote mailbox, select
Options > Delete. In Delete msg. from:, select Phone
only.
The device mirrors the e-mail headings in the remote
mailbox. Although you delete the message content, the
e-mail heading stays in your device. If you want to remove
the heading as well, you must first delete the e-mail
message from your remote mailbox, and then make a
connection from your device to the remote mailbox again
to update the status.
46
To delete an e-mail from the device and the remote
mailbox, select Options > Delete. In Delete msg. from:,
select Phone and server.
If you are offline, the e-mail is deleted first from your
device. During the next connection to the remote mailbox,
it is automatically deleted from the remote mailbox. If you
are using the POP3 protocol, messages marked to be
deleted are removed only after you have closed the
connection to the remote mailbox.
To cancel deleting an e-mail from the device and server,
scroll to an e-mail that has been marked to be deleted
during the next connection (), and select Options >
Undelete.
Disconnect from the mailbox
When you are online, to end the data connection to the
remote mailbox, select Options > Disconnect.
View messages on a SIM card
Before you can view SIM messages, you must copy them to
a folder in your device.
1 In the Messag. main view, select Options > SIM
messages.
2 Select Options > Mark/Unmark > Mark or Mark all to
mark messages.
3 Select Options > Copy. A list of folders opens.
4 To start copying, select a folder and OK. To view the
messages, open the folder.
Messaging settings
Fill in all fields marked with Must be defined or with a red
asterisk. Follow the instructions given by your service
provider. You may also obtain settings from your service
provider in a configuration message.
Some or all message centers or access points may be
preset for your device by your service provider or network
operator, and you may not be able to change, create, edit,
or remove them.
Text messages
Press , and select Messag. > Options > Settings >
Text msg. and from the following:
Message centres—View a list of all text message centers
that have been defined.
Character encoding— To use character conversion to
another encoding system when available, select Reduced
support.
Msg. centre in use—Select which message center is used
to deliver text messages.
Messaging
FCC DRAFT
47
Receive report—Select whether the network sends
delivery reports on your messages (network service).
Message validity—Select how long the message center
resends your message if the first attempt fails (network
service). If the recipient cannot be reached within the
Messaging
validity period, the message is deleted from the message
center.
Message sent as—Change this option only if you are sure
that your message center is able to convert text messages
into these other formats. Contact your network operator.
Preferred conn.—Select the connection used for sending
text messages: GSM network or packet data, if supported
by the network. See ‘Connection’, p. 98.
Reply via same ctr.—Select whether you want the reply
message to be sent using the same text message center
number (network service).
Multimedia messages
Press , and select Messag. > Options > Settings >
Multimedia message and from the following:
Image size—Define the size of the image in a multimedia
message: Original (shown only when the MMS creation
mode is set to Guided or Free), Small, or Large.
MMS creation mode —If you select Guided, the device
informs you if you try to send a message that may not be
supported by the recipient. Select Restricted; the device
prevents you from sending messages that may not be
supported.
Access point in use—Select which access point is used as
the preferred connection for the multimedia message
center.
Multimedia retrieval—Select how you want to receive
multimedia messages. To receive multimedia messages
automatically in your home network, select Aut. in home
network. Outside your home network, you receive a
notification that there is a multimedia message that you
can retrieve in the multimedia message center.
When you are outside your home network, sending and
receiving multimedia messages may cost you more.
If you select Multimedia retrieval > Always automatic,
your device automatically makes an active packet data
connection to retrieve the message both in and outside
your home network.
Allow anon. msgs.—Select whether you want to reject
messages from an anonymous sender.
Receive adverts—Define whether you want to receive
multimedia message advertisements.
Receive report—Select whether you want the status of the
sent message to be shown in the log (network service).
48
Receiving a delivery report of a multimedia message that
has been sent to an e-mail address may not be possible.
Deny report sending—Select whether you want to prevent
your device from sending delivery reports of received
multimedia messages.
Message validity—Select how long the message center
resends your message if the first attempt fails (network
service). If the recipient cannot be reached within the
validity period, the message is deleted from the message
center.
E-mail
Press , and select Messag. > Options > Settings >
E-mail and from the following:
Mailboxes—Select a mailbox to change the following
settings: Connection settings, User settings, Retrieval
settings, and Automatic retrieval.
Mailbox in use— Select which mailbox you want to use for
sending e-mail.
To create a new mailbox, select Options > New mailbox in
the mailbox main view.
Connection settings
To edit the settings for the e-mail you receive, select
Incoming e-mail and from the following:
User name—Enter your user name, given to you by your
service provider.
Password—Enter your password. If you leave this field
blank, you are prompted for the password when you try to
connect to your remote mailbox.
Incoming mail serv.—Enter the IP address or host name of
the mail server that receives your e-mail.
Access point in use—Select an Internet access point (IAP).
See ‘Connection’, p. 98.
Mailbox name—Enter a name for the mailbox.
Mailbox type—Defines the e-mail protocol that your
remote mailbox service provider recommends. The options
are POP3 and IMAP4. This setting can be selected only
once and cannot be changed if you have saved or exited
from the mailbox settings. If you use the POP3 protocol,
e-mail messages are not updated automatically when you
are online. To see the latest e-mail messages, you must
disconnect and make a new connection to your mailbox.
Security (ports)—Select the security option used to
secure the connection to the remote mailbox.
Port—Define a port for the connection.
APOP secure login (for POP3 only)—Use with the POP3
protocol to encrypt the sending of passwords to the
remote e-mail server while connecting to the mailbox.
Messaging
FCC DRAFT
49
To edit the settings for the e-mail you send, select
Outgoing e-mail and from the following:
My e-mail address—Enter the e-mail address given to
you by your service provider. Replies to your messages are
sent to this address.
Messaging
Outgoing mail serv.—Enter the IP address or host name
of the mail server that sends your e-mail. You may only be
able to use the outgoing server of your network operator.
Contact your service provider for more information.
Access point in use—Select an Internet access point (IAP).
See ‘Connection’, p. 98.
The settings for User name, Password, Security (ports),
and Port are similar to the ones in Incoming e-mail.
User settings
My name—Enter your own name. Your name replaces
your e-mail address in the recipient’s device when the
recipient’s device supports this function.
Send message—Define how e-mail is sent from your
device. Select Immediately for the device to connect to
the mailbox when you select Send message. If you select
During next conn., e-mail is sent when the connection to
the remote mailbox is available.
Send copy to self—Select whether you want to save a
copy of the e-mail to your remote mailbox and to the
address defined in My e-mail address.
Include signature—Select whether you want to attach a
signature to your e-mail messages.
New e-mail alerts—Select whether you want to receive
the new e-mail indications, a tone and a note, when new
mail is received to the mailbox.
Default encoding—Select another encoding according to
language.
Retrieval settings
E-mail to retrieve—Define which parts of the e-mail are
IMAP4 folder path (for IMAP4 only)—Define the folder
path for folders to be subscribed.
Folder subscriptions (for IMAP4 only)—Subscribe to other
folders in the remote mailbox and retrieve content from
those folders.
Automatic retrieval
E-mail notifications—Select whether you want to receive
notifications when new e-mail is received in your remote
mailbox.
E-mail notifications and automatic header retrieval cannot
be active at the same time.
50
Header retrieval—Select whether you want the device to
retrieve new e-mail automatically. You can define when,
and how often, the messages are retrieved.
Retrieving e-mail messages automatically may increase
your call costs due to the data traffic.
Web service messages
Press , and select Messaging > Options > Settings >
Service message. Select whether you want to receive
service messages. If you want to set the device to
automatically activate the browser and start a network
connection to retrieve content when you receive a service
message, select Download messages > Automatically.
Cell broadcast
Check the available topics and related topic numbers with
your service provider. Press , and select Messaging >
Options > Settings > Cell broadcast and from the
following:
Reception—Select whether you want to receive cell
broadcast messages.
Language—Select the languages in which you want to
receive messages: All, Selected, or Other.
Topic detection—Select whether the device automatically
searches for new topic numbers, and saves the new
numbers without a name to the topic list.
Other settings
Press , and select Messaging > Options > Settings >
Other and from the following:
Save sent messages—Select whether you want to save a
copy of the text messages, multimedia messages, or email that you send to the Sent folder.
No. of saved msgs.—Define how many sent messages are
saved to the Sent folder at a time. The default limit is 20
messages. When the limit is reached, the oldest message
is deleted.
Memory in use—If a memory card is inserted in the
device, select the memory where you want to save your
messages: Phone memory or Memory card.
Messaging
FCC DRAFT
51
Make calls
Voice calls
Make calls
You can make voice calls in the Fold open mode and View
mode. See ‘Modes’, p. 9.
1 To start a voice call, in the Fold open mode, enter the
2 Press to call the number.
3 Press to end the call (or to cancel the call
Pressing always ends a call, even if another
application is active.
To make a call from Contacts, press , and select
Contacts. Scroll to the desired name, or enter the first
52
FCC DRAFT
Tip! To increase or decrease the volume during a
call, press or . If you have set the volume to
Mute, you cannot adjust the volume with the or
keys. To adjust the volume, select Unmute, and
press or .
phone number in the standby mode, including the area
code. To remove a number, press .
For international calls, press twice for the +
character (replaces the international access code), and
enter the country code, area code (omit the leading
zero if necessary), and phone number.
attempt).
letters of the name to the search field. Matching contacts
are listed. To call, press . Select the call type Voice call.
You must copy the contacts from your SIM card to
Contacts before you can make a call this way. See ‘Copy
contacts’, p. 63.
To call your voice mailbox (network service), press and hold
in the standby mode. See also ‘Call divert’, p. 104.
Tip! To change the phone number of your voice
mailbox, press , and select Tools > Voic. mail >
Options > Change number. Enter the number
(obtained from your service provider), and select OK.
To call a recently dialed number in the standby mode, press
. Scroll to the number you want, and press to call
the number.
Make a conference call
1 Make a call to the first participant.
2 To make a call to another participant, select Options >
New call. The first call is automatically put on hold.
3 When the new call is answered, to join the first
participant in the conference call, select Options >
Conference.
To add a new person to the call, repeat step 2, and
select Options > Conference > Add to conference.
Your device supports conference calls between a
maximum of six participants, including yourself.
To have a private conversation with one of the
participants, select Options > Conference > Private.
Select a participant, and select Private. The conference
call is put on hold on your device. The other
participants can still continue the conference call.
When you finish the private conversation, select
Options > Add to conference to return to the
conference call.
To drop a participant, select Options > Conference >
Drop participant, scroll to the participant, and select
Drop.
4 To end the active conference call, press .
Speed dial a phone number
To activate speed dialing, press , and select Tools >
Settings > Call > Speed dialling > On.
To assign a phone number to one of the speed dialing keys
(—), press , and select Tools > Spd. dial. Scroll to
the key to which you want to assign the phone number,
and select Options > Assign. is reserved for the voice
mailbox.
To call in the standby mode, press the speed dial key and
.
Voice dialing
Your device supports enhanced voice commands.
Enhanced voice commands are not dependent on the
speaker’s voice; you do not record voice tags in advance.
Instead, the device creates a voice tag for the entries in
contacts, and compares the spoken voice tag to it. The
voice recognition in the device adapts to the main user’s
voice to recognize the voice commands better.
The voice tag for a contact is the name or nickname that
is saved on the contact card. To listen to the synthesized
voice tag, open a contact card, and select Options > Play
voice tag.
Make a call with a voice tag
Note: Using voice tags may be difficult in a noisy
environment or during an emergency, so you should
not rely solely upon voice dialing in all circumstances.
When you use voice dialing, the loudspeaker is in use. Hold
the device at a short distance away when you say the
voice tag.
1 To start voice dialing, in the standby mode, press and
hold . If you are using a compatible headset with
Make calls
53
the headset key, press and hold the headset key to
start voice dialing.
2 A short tone is played, and Speak now is displayed. Say
clearly the name or nickname that is saved on the
Make calls
contact card.
3 The device plays a synthesized voice tag for the
recognized contact in the selected device language,
and displays the name and number. After a timeout of
2.5 seconds, the device dials the number.
If the recognized contact was not correct, select Next
to view a list of other matches, or Quit to cancel voice
dialing.
If several numbers are saved under the name, the device
selects the default number, if it has been set. Otherwise
the device selects the first available number of the
following: Mobile, Mobile (home), Mobile (business),
Telephone, Tel. (home), and Tel. (business).
Video calls
You can make video calls in the Fold open mode and View
mode. See ‘Modes’, p. 9.
For hands-free video calls, use the View mode.
When you make a video call, you can see a real-time,
two-way video between you and the recipient of the call.
The live video image, or video image captured by the
camera in your device is shown to the video call recipient.
To be able to make a video call, you must have a USIM card
and be in the coverage of a UMTS network. For availability
of and subscription to video call services, contact your
network operator or service provider. A video call can only
be made between two parties. The video call can be made
to a compatible mobile phone or an ISDN client. Video calls
cannot be made while there is another voice, video, or data
call active.
Icons:
You are not receiving video (the recipient is not
sending video or the network is not transmitting it).
You have denied video sending from your device. To
send a still image instead, see ‘Call settings’, p. 97.
1 To start a video call, in the
Fold open mode, enter the
phone number in the
standby mode, or select
Contacts and a contact.
2 Select Options > Call >
Video call.
If you want to make a
hands-free video call, activate
the View mode after the call
recipient has answered the call.
54
FCC DRAFT
Starting a video call may take a while. Waiting for video
image is shown. If the call is not successful (for example,
video calls are not supported by the network, or the
receiving device is not compatible) you are asked if you
want to try a normal call or send a message instead.
The video call is active when you see two video images, and
hear the sound through the loudspeaker. The call recipient
may deny video sending (), in which case you hear the
sound and may see a still image or a grey background
graphic.
Tip! To increase or decrease the volume during a call,
scroll left or right.
To change between showing video or hearing only sound,
select Enable/Disable > Sending video, Sending audio, or
Sending audio & video.
To zoom your own image, select Zoom in or Zoom out. The
zoom indicator is shown on the top of the display.
To switch the places of the sent and received video images
on the display, select Change image order.
Even if you have denied video sending during a video call,
the call will still be charged as a video call. Check the
pricing with your network operator or service provider.
To end the video call, press .
Video sharing (network service)
Use Video sharing to send live video or a video clip from
your mobile device to another compatible mobile device
during a voice call. Simply invite a recipient to view the
live video, or a video clip you want to share. Sharing
begins automatically when the recipient accepts the
invitation, and you activate the correct mode. See ‘Share
video’, p. 56.
Video sharing requirements
Because Video sharing requires a 3G Universal Mobile
Telecommunications System (UMTS) connection, your
ability to use Video sharing depends on 3G network
availability. Contact your service provider for questions
about network availability and fees associated with using
this application. To use Video sharing you must:
• Ensure that Video sharing is installed on your Nokia
N93.
• Ensure that your device is set up for person-to-person
connections. See ‘Settings’, p.56.
• Ensure you have an active UMTS connection and are
within UMTS network coverage. See ‘Settings’, p. 56. If
you start the sharing session while you are within
UMTS network coverage and a handover to GSM
occurs, the sharing session is discontinued, but your
voice call continues.
Make calls
55
• Ensure that both the sender and recipient are
registered to the UTMS network. If you invite someone
to a sharing session and that person’s phone is turned
off, or the person is not within UMTS network
Make calls
coverage, they do not know that you are sending an
invitation. However, you receive an error message that
the recipient cannot accept the invitation.
Settings
Person-to-person connection settings
A person-to-person connection is also known as a Session
Initiation Protocol (SIP) connection. The SIP profile
settings must be configured in your device before you can
use Video sharing. Setting up a SIP profile allows you to
establish a live person-to-person connection to another
compatible phone. The SIP profile must also be established
to receive a sharing session.
Ask your network operator or service provider for the SIP
profile settings, and save them in your device. Your
network operator or service provider may send you the
settings over the air.
If you know a recipient’s SIP address, you can enter it on
your contact card for that person. Open Contacts from
your device main menu, and open the contact card (or
start a new card for that person). Select Options > Add
detail > Web address. Enter the SIP address in the format
sip:username@domainname (you can use an IP address
instead of a domain name).
UTMS connection settings
To set up your UMTS connection, do the following:
• Contact your service provider to establish an
agreement for you to use the UMTS network.
• Ensure that your device UMTS access point connection
settings are configured properly. For help, see
‘Connection’, p. 98.
Share video
To receive a sharing session, the recipient must install
Video sharing and configure the required settings on their
mobile device. You and the recipient must both be
registered to the service before you can start sharing.
To receive share invitations, you must be registered to the
service, have an active UMTS connection, and be within
the UMTS network coverage.
Live video
1 When a voice call is active, select Options > Share
video > Live.
2 The phone sends the invitation to the SIP address you
have added to the contact card of the recipient.
56
FCC DRAFT
If the recipient has several SIP addresses in the contact
card, select the SIP address to which you want to send
the invitation, and Select to send the invitation.
If the SIP address of the recipient is not available, enter
a SIP address. Select OK to send the invitation.
3 Sharing begins automatically when the recipient
accepts the invitation.
The loudspeaker is active. You can also use a headset to
continue your voice call while you share live video.
4 Select Pause to pause the sharing session. Select
Continue to resume sharing.
5 To end the sharing session, select Stop. To end the voice
call, press the end key.
Video clip
1 When a voice call is active, select Options > Share
video > Clip.
A list of video clips opens.
2 Select a video clip you want to share. A preview view
opens. To preview the clip, select Options > Play.
3 Select Options > Invite.
You may need to convert the video clip into a suitable
format to be able to share it. Clip must be converted
for sharing. Continue? appears. Select OK.
The phone sends the invitation to the SIP address you
have added to the contact card of the recipient.
If the recipient has several SIP addresses in the contact
card, select the SIP address to which you want to send
the invitation, and Select to send the invitation.
If the SIP address of the recipient is not available, enter
a SIP address. Select OK to send the invitation.
4 Sharing begins automatically when the recipient
accepts the invitation.
5 Select Pause to pause the sharing session. Select
Options > Continue to resume sharing.
6 To end the sharing session, select Stop. To end the
voice call, press the end key.
Accept an invitation
When someone sends you a share invitation, an invitation
message is displayed showing the sender’s name or SIP
address. If your device is not set to Silent, it rings when
you receive an invitation.
If someone sends you a share invitation and you are not
within UMTS network coverage, you will not know that
you received an invitation.
When you receive an invitation, you can select:
• Accept to begin the sharing session. If the sender
wants to share live video, activate the View mode.
• Reject to decline the invitation. The sender receives a
message that you rejected the invitation. You can also
Make calls
57
press the end key to decline the sharing session and
disconnect the voice call.
To end the sharing session, select Stop. If you share a
video clip, select Exit. Video sharing ended is displayed.
Make calls
Answer or reject a call
To answer the call in the Fold open mode, press . If
Anykey answer is set to On, to answer a call in the Fold
closed mode, open the fold, and the call starts
automatically. Otherwise, open the fold, and press .
To mute the ringing tone when a call comes in, select
Silence.
Tip! If a compatible headset is connected to the
device, to answer and end a call, press the headset key.
If you do not want to answer a call, in the Fold open mode,
press to reject it. The caller hears a line busy tone. If
you have activated the Call divert > If busy function to
divert calls, rejecting an incoming call also diverts the call.
See ‘Call divert’, p. 104.
When you reject an incoming call in the Fold open mode,
you can also send a text message to the caller informing
why you cannot answer the call. Select Options > Send
msg.. You can edit the text before sending it. To set up this
option and write a standard text message, see ‘Call
settings’, p. 97.
If you answer a voice call during a video call, the video call
is dropped. Call waiting is not available during a video call.
Answer or reject a video call
When a video call arrives, is displayed.
Tip! You can assign a ringing tone for video calls.
Press and select Tools > Profiles, a profile, and
Options > Personalise > Video call tone.
In the Fold open mode, press to answer the video call.
To start sending video, activate the View mode, and a live
video image, recorded video clip, or the image being
captured by the camera in your device is shown to the
caller. If you want to send a live video image, turn the
camera unit to the direction from which you want to send
the video image. If you do not activate the View mode,
video sending is not possible, but you can still hear the
other person. A grey screen is shown in place of the video.
To replace the grey screen with a still image, see ‘Call
settings’, Image in video call, p. 97.
Note: Even if you have denied video sending during
a video call, the call is still charged as a video call.
Check the pricing with your network operator or service
provider.
To end the video call, in the View mode or in the Fold open
mode, press .
58
FCC DRAFT
Call waiting (network service)
You can answer a call while you have another call in
progress if you have activated Call waiting in Tools >
Settings > Call > Call waiting.
To answer the waiting call, press . The first call is put
on hold.
To switch between the two calls, select Swap. Select
Options > Transfer to connect an incoming call or a call
on hold wi th a n activ e ca ll and t o di sconne ct y ourself from
the calls. To end the active call, press . To end both
calls, select Options > End all calls.
Options during a voice call
Many of the options that you can use during a voice call
are network services. Select Options during a call for some
of the following options: Mute or Unmute, Answer,
Reject, Swap, Hold or Unhold, Activate handset, Activate
loudsp., or Activate handsfree (if a compatible headset
with Bluetooth connectivity is attached), End active call
or End all calls, New call, Conference, and Transfer.
Select from the following:
Replace—To end an active call and replace it by answering
the waiting call.
Send MMS (in UMTS networks only)—To send an image or
a video in a multimedia message to the other participant
of the call. You can edit the message and change the
recipient before sending. Press to send the file to a
compatible device.
Send DTMF—To send DTMF tone strings, for example, a
password. Enter the DTMF string or search for it in
Contacts. To enter a wait character (w) or a pause
character (p), press repeatedly. Select OK to send the
tone.
Tip! You can add DTMF tones to the Phone number
or DTMF fields in a contact card.
Options during a video call
Select Options during a video call for the following
options: Enable or Disable (audio in the Fold open mode;
video, audio, or both in the View mode); Activate handset
(if a headset with Bluetooth connectivity is attached);
Activate loudsp.; or Activate handsfree (Fold open mode
only, and if a headset with Bluetooth connectivity is
attached); End active call; Change image order Zoom in/
Zoom out (View mode only); and Help.
Make calls
59
Log
Recent calls
Make calls
To monitor the phone numbers of missed, received, and
dialed calls, press , and select Extras > Log > Recent
calls. The device registers missed and received calls only if
the network supports these functions, the device is
switched on, and within the network service area.
Tip! When you see a note in the standby mode about
missed calls, select Show to access the list of missed
calls. To call back, scroll to a name or number, and
press .
To clear all recent call lists, select Options > Clear recent
calls in the recent calls main view. To clear one of the call
registers, open the register you want to erase, and select
Options > Clear list. To clear an individual event, open a
register, scroll to the event, and press .
Call duration
To monitor the approximate duration of your incoming
and outgoing calls, press , and select Extras > Log >
Call duration.
To set the display of the call duration while a call is active,
select Connect. > Log > Options > Settings > Show call
duration > Yes or No.
Note: The actual time invoiced for calls by your
service provider may vary, depending on network
features, rounding off for billing, and so forth.
To clear call duration timers, select Options > Clear
timers. For this you need the lock code; see ‘Security’,
‘Phone and SIM’, p. 101.
Packet data
To check the amount of data sent and received during
packet data connections, press , and select Extras > Log
> Packet data. For example, you may be charged for your
packet data connections by the amount of data sent and
received.
Monitor all communication events
Icons in Log:
Incoming
Outgoing
Missed communication events
60
FCC DRAFT
To monitor all voice and video
calls, text messages, or data
connections registered by the
device, press , select Extras
> Log, and scroll to the right to
open the general log. For each
communication event, you can
see the sender or recipient
name, phone number, name of
the service provider, or access
point. You can filter the general
log to view just one type of event and create new contact
cards based on the log information.
Tip! To see the duration of a voice call on the main
display during an active call, select Options > Settings
> Show call duration > Yes.
Tip! To view a list of sent messages, press , and
select Messaging > Sent.
Subevents, such as a text message sent in more than one
part and packet data connections, are logged as one
communication event. Connections to your mailbox,
multimedia messaging center, or Web pages are shown as
packet data connections.
To filter the log, select Options > Filter and a filter.
To erase the contents of the log, recent calls register, and
messaging delivery reports permanently, select Options >
Clear log. Select Yes to confirm. To remove a single event
from the log, press .
To set the Log duration, select Options > Settings > Log
duration. The log events remain in the phone memory for
a set number of days after which they are automatically
erased to free memory. If you select No log, all the log
contents, recent calls register, and messaging delivery
reports are permanently deleted.
To view the details of a communication event, in the
general log view, scroll to an event, and press the scroll
key.
Tip! In the details view, to copy a phone number to
the clipboard, select Options > Copy Number.
Packet data counter and connection timer: To view how
much data, measured in kilobytes, is transferred and how
long a certain packet data connection lasts, scroll to an
incoming or outgoing event indicated by Pack., and select
Options > View details.
Make calls
61
Contacts (Phonebook)
Press , and select Contacts. In Contacts you can add a
personal ringing tone or a thumbnail image to a contact
card. You can also create contact groups, which allow you
to send text messages or e-mail to many recipients at the
same time. You can add received contact information
(business cards) to contacts. See ‘Data and settings’, p. 44.
Contact information can only be sent to or received from
Contacts (Phonebook)
compatible devices.
Save names and numbers
1 Select Options > New contact.
2 Fill in the fields that you want, and select Done.
To edit contact cards in Contacts, scroll to the contact
card you want to edit, and select Options > Edit.
Tip! To print contact cards on a compatible Basic
Print Profile (BPP) equipped printer with Bluetooth
connectivity (such as HP Deskjet 450 Mobile Printer or
HP Photosmart 8150), select Options > Print.
To delete a contact card in Contacts, select a card, and
press . To delete several contact cards at the same time,
press and to mark the contacts, and press to
delete.
62
FCC DRAFT
Tip! To add and edit contact cards, use Nokia Contacts
Editor available in Nokia PC Suite.
To attach a small thumbnail image to a contact card, open
the contact card, and select Options > Edit > Options >
Add thumbnail. The thumbnail image is shown when the
contact calls.
Tip! Speed dialing is a quick way to call frequently
used numbers. You can assign speed dialing keys to
eight phone numbers. See ‘Speed dial a phone number’,
p. 53.
Tip! To send contact information, select the card you
want to send. Select Options > Send > Via text
message, Via multimedia, Via Bluetooth, or Via
infrared. See ‘Messaging’, p. 39 and ‘Send data using
Bluetooth connectivity’, p. 81.
To add a contact to a group, select Options > Add to
group: (shown only if you have created a group). See
‘Create contact groups’, p. 64.
To view the amount of contacts, groups, and the available
memory in Contacts, select Options > Contacts info.
Default numbers and addresses
You can assign default numbers or addresses to a contact
card. In this way if a contact has several numbers or
addresses, you can easily call or send a message to the
contact to a certain number or address. The default
number is also used in voice dialing.
1 In the address book, select a contact, and press .
2 Select Options > Defaults.
3 Select a default to which you want to add a number or
an address, and select Assign.
4 Select a number or an address you want to set as a
default.
The default number or address is underlined in the contact
card.
Copy contacts
To copy names and numbers from a SIM card to your
device, press , and select Contacts > Options > SIM
contacts > SIM directory. Select the names you want to
copy and Options > Copy to Contacts.
To copy contacts to your SIM card, press , and select
Contacts. Select the names you want to copy and
Options > Copy to SIM direct., or Options > Copy > To
SIM directory. Only the contact card fields supported by
your SIM card are copied.
Tip! You can synchronize your contacts to a
compatible PC with Nokia PC Suite.
SIM directory and other SIM services
For availability and information on using SIM card
services, contact your SIM card vendor. This may be the
service provider, network operator, or other vendor.
Press , and select Contacts > Options > SIM
contacts > SIM directory to see the names and numbers
stored on the SIM card. In the SIM directory you can add,
edit, or copy numbers to contacts, and you can make calls.
To view the list of fixed dialing numbers, select Options >
SIM contacts > Fixed dialling contacts. This setting is
only shown if supported by your SIM card.
To restrict calls from your device to selected phone
numbers, select Options > Activ. fixed dialling. To add
new numbers to the fixed dialing list, select Options >
New SIM contact. You need the PIN2 code for these
functions.
When you use Fixed dialling, packet data connections are
not possible, except when sending text messages over a
packet data connection. In this case, the message center
number and the recipient’s phone number must be
included on the fixed dialing list.
Contacts (Phonebook)
63
When fixed dialing is activated, calls may be possible to
the official emergency number programmed into your
device.
Add ringing tones for contacts
When a contact or group member calls you, the device
plays the chosen ringing tone (if the caller’s telephone
number is sent with the call and your device recognizes
it).
Contacts (Phonebook)
1 Press to open a contact card or go to the groups
list, and select a contact group.
2 Select Options > Ringing tone. A list of ringing tones
opens.
3 Select the ringing tone you want to use for the
individual contact or the selected group.
You can also use a video clip as a ringing tone.
To remove the ringing tone, select Default tone from the
list of ringing tones.
Create contact groups
1 In Contacts, press to open the groups list.
2 Select Options > New group.
3 Write a name for the group or use the default name
Group %N, and select OK.
4 Open the group, and select Options > Add members.
5 Scroll to a contact, and press to mark it. To add
multiple members at a time, repeat this action on all
the contacts you want to add.
6 Select OK to add the contacts to the group.
To rename a group, select Options > Rename, enter the
new name, and select OK.
Remove members from a group
1 In the groups list, open the group you want to modify.
2 Scroll to the contact, and select Options > Remove
from group.
3 Select Yes to remove the contact from the group.
Tip! To check to which groups a contact belongs,
scroll to the contact, and select Options > Belongs to
groups.
64
FCC DRAFT
Web
Web
Various service providers maintain pages specifically
designed for mobile devices. These pages use the wireless
markup language (WML), extensible hypertext markup
language (XHTML), or hypertext markup language (HTML).
Check the availability of services, pricing, and fees with
your network operator or service provider. Service
providers will also give you instructions on how to use their
services.
Press , and select Services.
Shortcut: To start a connection, press and hold
in the standby mode.
Web access point
To access pages, you need Web service settings for the
page that you want to use. You may receive the settings in
a special text message from the network operator or
service provider that offers the Web page. See ‘Data and
settings’, p. 44. For more information, contact your
network operator or service provider.
Tip! Settings may be available on the Web site of a
network operator or service provider.
Enter settings manually
1 Press , select Tools > Settings > Connection >
Access points, and define the settings for an access
point. Follow the instructions given to you by your
service provider. See ‘Connection’, p. 98.
2 Press , and select Services > Options > Bookmark
manager > Add bookmark. Write a name for the
bookmark and the address of the page defined for the
current access point.
3 To set the created access point as the default access
point, select Options > Settings > Access point.
Bookmarks view
The bookmarks view opens when you open Services.
Your device may have some bookmarks loaded for sites not
affiliated with Nokia. Nokia does not warrant or endorse
these sites. If you choose to access them, you should take
the same precautions, for security or content, as you
would with any Internet site.
indicates the starting page defined for the default
access point.
FCC DRAFT
65
Connection security
Web
If the security indicator is displayed during a
connection, the data transmission between the device and
the Internet gateway or server is encrypted.
The security icon does not indicate that the data
transmission between the gateway and the content server
(or place where the requested resource is stored) is secure.
The service provider secures the data transmission
between the gateway and the content server.
Select Options > Details > Security to view details about
the connection, encryption status, and information about
server and user authentication.
Security certificates may be required for some services,
such as banking services. For more information, contact
your service provider. See also ‘Certif. management’,
p. 103.
Browse
Important: Use only services that you trust and that
offer adequate security and protection against harmful
software.
To download a page, select a bookmark, or enter the
address in the field ().
On a browser page, new links appear underlined in blue
and previously visited links in purple. Images that act as
links have a blue border around them.
To open links and make selections, press .
Shortcut: Use to jump to the end of a page and
to the beginning of a page.
To go to the previous page while browsing, select Back. If
Back is not available, select Options > Navigation
options > History to view a chronological list of the pages
you visited during a browsing session.
To retrieve the latest content from the server, select
Options > Navigation options > Reload.
To save a bookmark, select Options > Save as bookmark.
Tip! To access the bookmarks view while browsing,
press and hold . To return to the browser view, select
Options > Back to page.
To save a page while browsing, select Options > Advanced
options > Save page. You can save pages to the device
memory or memory card (if inserted), and browse them
when offline. To access the pages later, press in the
bookmarks view to open the Saved pages view.
To enter a new URL address, select Options > Navigation
options > Go to web address.
66
To open a sublist of commands or actions for the currently
open page, select Options > Service options.
You can download files that cannot be shown on the
browser page, such as ringing tones, images, operator
logos, themes, and video clips. To download an item, scroll
to the link, and press .
When you start a download, a list of ongoing, paused, and
completed downloads from the current browsing session is
displayed. You can also view the list by selecting Options >
Tools > Downloads. In the list, scroll to an item, and select
Options to pause, resume, or cancel ongoing downloads, or
open, save, or delete completed downloads.
Copyright protections may prevent some images, music
(including ringing tones), and other content from being
copied, modified, transferred or forwarded.
Important: Only install and use applications and
other software from sources that offer adequate security
and protection against harmful software.
Download and purchase items
You can download items such as ringing tones, images,
operator logos, themes, and video clips. These items can be
provided free, or you can purchase them. Downloaded
items are handled by the respective applications in your
device, for example, a downloaded photo can be saved in
Gallery.
Important: Only install and use applications and
other software from sources that offer adequate security
and protection against harmful software.
1 To download the item, scroll to the link, and press .
2 Select the appropriate option to purchase the item, for
example, “Buy”.
3 Carefully read all the information provided.
To continue the download, select Accept. To cancel the
download, select Cancel.
End a connection
To end the connection and view the browser page offline,
select Options > Advanced options > Disconnect, or to
end the connection and close the browser, select
Options > Exit.
Empty the cache
The information or services you have accessed are stored
in the cache memory of the device.
A cache is a memory location that is used to store data
temporarily. If you have tried to access or have accessed
confidential information requiring passwords, empty the
cache after each use. The information or services you have
Web
FCC DRAFT
67
accessed are stored in the cache. To empty the cache,
select Options > Advanced options > Clear cache.
Web
Web settings
Select Options > Settings and from the following:
Access point—Change the default access point. See
‘Connection’, p. 98. Some or all access points may be
preset for your device by your service provider or network
operator, and you may not be able to change, create, edit,
or remove them.
Load imgs. & sounds—Select whether you want to load
images while browsing. If you select No, to load images
later during browsing, select Options > Show images.
Font size—Select the text size.
Default encoding—If text characters are not shown
correctly, you can select another encoding according to
language.
Auto. bookmarks—Enable or disable automatic bookmark
collecting. If you want to continue collecting automatic
bookmarks but hide the folder from the bookmarks view,
select Hide folder.
Screen size—Select what is shown when you are
browsing: Select. keys only or Full screen.
Homepage—Define the home page.
Search page—Define a Web page that is downloaded
when you select Navigation options > Open search page
in the bookmarks view, or when browsing.
Volume—If you want the browser to play sounds
embedded on Web pages, select a volume level.
Rendering—If you want the page layout shown as
accurately as possible when in the Small screen mode,
select By quality. If you do not want external cascading
style sheets to be downloaded, select By speed.
Cookies—Enable or disable the receiving and sending of
cookies.
Java/ECMA script—Enable or disable the use of scripts.
Security warnings—Hide or show security notifications.
Conf. DTMF sending—Select whether you want to confirm
before the device sends DTMF tones during a voice call. See
also ‘Options during a voice call’, p. 59.
68
Calendar
Use Calendar to remind you of meetings, anniversaries,
and to keep track of your tasks and other notes.
Create calendar entries
Shortcut: In the day, week, or month calendar view,
press any key (—). An appointment entry opens,
and the characters you enter are added to the Subject
field. In the to-do view, a to-do note entry opens.
1 Press , and select
Calendar > Options >
New entry and one of the
following:
Meeting—to remind you
of an appointment that
has a specific date and
time
Meeting request—to
send a meeting request by
e-mail (a mailbox must be
defined in the device)
Memo—to write a general
entry for a day
Anniversary—to remind you of birthdays or special
dates (entries are repeated every year)
To-do—to remind you of a task that needs doing by a
specific date
2 Fill in the fields. To set an alarm, select Alarm > On,
and enter the Alarm time and Alarm date.
To add a description for an appointment or a meeting,
select Options > Add description.
3 To save the entry, select Done.
When the calendar alarms for a note, select Silence to
turn off the calendar alarm tone. The reminder text stays
on the screen. To end the calendar alarm, select Stop. To
set the alarm to snooze, select Snooze.
Tip! You can synchronize your calendar with a
compatible PC using Nokia PC Suite. When creating a
calendar entry, set the desired Synchronisation
option.
Meeting requests
If you receive a meeting request to the mailbox in your
device, the request is saved to the calendar when you open
the e-mail.
FCC DRAFT
Calendar
69
You can view received meeting requests in the mailbox or
in the calendar. To respond to a meeting request using
e-mail, select Options > Respond.
Calendar
Calendar views
Tip! Select Options > Settings to change the
starting day of the week or the view that is shown
when you open the calendar.
In the month view, dates that have calendar entries are
marked with a small triangle in the bottom right corner.
In the week view, memos and anniversaries are placed
before 8 a.m. To switch between the month view, week
view, day view, and to-do view, press .
To go to a certain date, select Options > Go to date. To
jump to today, press .
To send a calendar note to a compatible device, select
Options > Send.
To print calendar entries on a compatible Basic Print
Profile (BPP) equipped printer with Bluetooth connectivity
(such as HP Deskjet 450 Mobile Printer or HP Photosmart
8150), select Options > Print.
Manage your calendar entries
Deleting past entries in Calendar saves space in your
device memory.
To delete more than one event at a time, go to the month
view, and select Options > Delete entry > Before date or
All entries.
To mark a task as completed, scroll to it in the to-do view,
and select Options > Mark as done.
Calendar settings
To modify the Calendar alarm tone, Default view, Week
starts on, Week view title, and select Options > Settings.
70
My own
Visual Radio (network
service)
You can use the Visual Radio application as a traditional
FM radio with automatic tuning and saved stations. If you
tune to stations that offer Visual Radio service, you can
view visual information on the display related to the radio
program. The Visual Radio service uses packet data
(network service). You can listen to the FM radio while
using other applications.
To use the Visual Radio service, the following conditions
are required:
• The device must be switched on.
• The device must have a valid SIM card inserted.
• The station you listen to and the network operator you
use must support this service.
• An Internet access point must be defined to access the
operator’s visual radio server. See ‘Access points’, p. 98.
• The station must have the correct Visual Radio service
ID defined and Visual Radio service enabled. See ‘Saved
stations’, p. 73.
If you do not have access to the Visual Radio service, the
operators and radio stations in your area may not support
Visual Radio. The Visual Radio service may not be available
in all areas and countries.
The FM radio depends on an antenna other than the
wireless device antenna. A compatible headset or
enhancement needs to be attached to the device for the
FM radio to function properly.
You can listen to the radio with the built-in loudspeaker
or a compatible headset. When using the loudspeaker,
keep the headset plugged in the device. The lead of the
headset functions as the antenna of the radio, so let it
hang freely.
Warning: Listen to music at a moderate level.
Continuous exposure to high volume may damage your
hearing. Do not hold the device near your ear when the
loudspeaker is in use, because the volume may be
extremely loud.
You can make a call or answer an incoming call while
listening to the radio. The radio is turned off when there is
an active call. When the call is finished, the radio is turned
back on.
The radio selects the used frequency band based on the
country information received from the network.
My own
71
Visual Radio can be used for listening when the device
cover is closed. Channel information may be displayed on
the cover display. To mute or unmute the radio, press the
cover key.
My own
Listen to the radio
Note that the quality of the radio broadcast depends on
the coverage of the radio station in that particular area.
Connect a compatible headset to the device. The lead of
the headset functions as the radio antenna, so let it hang
freely. Press , and select My own > Radio.
To start a station search, select or . Searching
stops when a station is found. To change the frequency
manually, select Options > Manual tuning.
If you have previously saved radio stations, select or
to go to the next or previous saved station. To select
the memory location of a station, press the corresponding
number key.
To adjust the volume, press or . To listen to the
radio using the loudspeaker, select Options > Activate
loudspeaker.
To view available stations based on location, select
Options > Station directory (network service).
To save the current tuned
station to your station list,
select Options > Save
station. To open the list of
your saved stations, select
Options > Stations. See
‘Saved stations’, p. 73.
To return to the standby
mode and leave the FM radio
playing in the background,
select Options > Play in
background, or press .
View visual content
To check availability and costs, and to subscribe to the
service, contact your network operator or service provider.
To view available visual content for a tuned station, select
, or in the stations view, select Options > Station >
Start visual service. If the visual service ID has not been
saved for the station, enter it, or select Retrieve to search
for it in the station directory (network service).
When the connection to the visual service is established,
the display shows the current visual content designed by
the content provider.
72
FCC DRAFT
To adjust display settings for the visual content view,
select Options > Display settings > Lighting or Power
saver time-out.
Saved stations
You can save up to 20 radio stations in Visual Radio. To
open your station list, select Options > Stations.
To listen to a saved station, select Options > Station >
Listen. To view available visual content for a station with
Visual Radio service, select Options > Station > Start
visual service.
To change station details, select Options > Station > Edit.
Settings
Select Options > Settings and from the following:
Start-up tone—To select a tone to play when the
application is started.
Auto-start service—To have the Visual Radio service start
automatically when you select a saved station that offers
visual service, select Yes.
Access point—To select the access point used for the data
connection. You do not need an access point to use the
application as an ordinary FM radio.
RealPlayer
Press , and select My own > RealPlyr.. With RealPlyr.,
you can play video clips or stream media files over the air.
You can activate a streaming link when you browse Web
pages, or store it in the device memory or a compatible
memory card (if inserted).
Tip! You can also view video clips or streaming links
in your device with other compatible UPnP devices,
such as a TV or a PC, through wireless LAN. See ‘View
media files’, p. 87.
RealPlyr. supports files with extensions such as .3gp,
.mp4, or .rm. However, RealPlyr. does not necessarily
support all file formats or all the variations of file formats.
For example, RealPlyr. attempts to open all .mp4 files, but
some .mp4 files may include content that is not compliant
with 3GPP standards and, therefore, is not supported by
this device.
Play video clips
1 To play a media file stored in device memory or on the
memory card (if inserted), select Options > Open and
from the following:
Most recent clips—to play one of the last six files
played in RealPlyr.
My own
73
Saved clip—to play a file saved in Gallery
See ‘Gallery’, p. 29.
2 Scroll to a file, and press to play the file.
My own
Tip! To view a video clip in full screen mode, press
. Press again to change back to normal screen mode.
Shortcuts during play:
• To fast forward, press and hold .
• To rewind through the media file, press and hold .
• To mute the sound, press and hold until is
displayed. To turn on the sound, press and hold
until you see .
Stream content over the air
Many service providers require you to use an Internet
access point (IAP) for your default access point. Other
service providers allow you to use a WAP access point.
The access points may be configured when you first start
your device.
Contact your service provider for more information.
In RealPlyr., you can only open an rtsp:// URL address.
However, RealPlyr. recognizes an http link to a .ram file.
To stream content over the air, select a streaming link
saved in Gallery, on a Web page, or received in a text
message or multimedia message. Before live content
begins streaming, your device connects to the site and
starts loading the content. The content is not saved in your
device.
Receive RealPlayer settings
You may receive RealPlyr. settings in a special text
message from the network operator or service provider.
See ‘Data and settings’, p. 44. For more information,
contact your network operator or service provider.
Change the RealPlayer settings
Select Options > Settings and from the following:
Video—to have RealPlyr. automatically repeat video clips
after they finish playing.
Connection—to select whether to use a proxy server,
change the default access point, and set the port range
used when connecting. Contact your service provider for
the correct settings.
Proxy sett.:
Use proxy—To use a proxy server, select Yes.
Proxy serv. address—Enter the IP address of the proxy
server.
Proxy port number—Enter the port number of the proxy
server.
Glossary: Proxy servers are intermediate servers between
media servers and their users. Some service providers
74
FCC DRAFT
use them to provide additional security or speed up
access to browser pages that contain sound or video
clips.
Netw. sett.:
Default access point—Scroll to the access point you want
to use to connect to the Internet, and press .
Online time—Set the time for RealPlyr. to disconnect from
the network when you pause a media clip playing through
a network link. Select User defined, and press . Enter
the time, and select OK.
Lowest UDP port—Enter the lowest port number of the
server’s port range. The minimum value is 1024.
Highest UDP port—Enter the highest port number of the
server’s port range. The maximum value is 65535.
Select Options > Advanced settings to edit the
bandwidth values for different networks.
Flash Player
With Flash Player, you can view, play, and interact with
flash files made for mobile devices.
Organise flash files
Press , and select My own > Flash Player. Scroll right.
To open a folder or play a flash file, scroll to it, and press
.
To send a flash file to a compatible device, scroll to it, and
press .
To copy a flash file to another folder, select Organise >
Copy to folder.
To move a flash file to another folder, select Organise >
Move to folder
To create a folder to organize your flash files, select
Organise > New folder.
The available options may vary.
To delete a flash file, scroll to it, and press .
Play flash files
Press , and select My own > Flash Player. Scroll to a
flash file and press .
Select Options and from the following:
Note: Options may not be available in all flash files.
• Pause to pause the playback.
• Stop to stop the playback.
My own
75
• Volume to adjust the playback volume. To increase or
decrease the volume scroll left or right.
• Quality to select the playback quality.
My own
If the playback appears uneven and slow, change the
Quality setting to Normal or Low.
• Full screen to play the file using the entire display. To
return to the normal screen, select Normal screen.
Even though not visible in full screen, the key
functions may still be available when you press either
key below the display.
• Fit to screen to play the file in its original size after
zooming it.
• Pan mode on to be able to move around the display
with the scroll key when you have zoomed in.
The available options may vary.
Movie director
Create muvees
1 In the Movie director main view, select the videos and
images you want to create a muvee with and select
Options > Create muvee, or open the Images & video
folder in Gallery. Select the video clips and images you
want to create a muvee with and select Options >
Edit > Create muvee.
2 Select a style for the muvee from the style list. Movie
director uses the music and text associated with the
chosen style.
3 Select Create muvee.
The muvee is created automatically and a Preview view is
displayed. You can select Save to save the muvee in the
Gallery, Recreate to shuffle the media files and create a
new muvee, or press Back to select a different style for
your muvee. You can also select Customise to change the
muvee settings and create a custom muvee to which you
can add images, music, and text.
76
Press , and select My own > Movie, or launch it from
the gallery. Muvees are styled video clips that can contain
videos, images, music, and text. The style determines the
rtransitions, visual effects, graphics, music, and text that
are used in the muvee.
FCC DRAFT
Create a custom muvee
1 .In the Movie director main view, select the videos and
images you want to create a muvee with and select
Options > Create muvee, or select the Images & video
folder in Gallery. Select the videos and images you
want to create a muvee with and select Options >
Edit > Create muvee.
2 Select a style for the muvee from the style list. In the
style view, select Options > Customise. Select from
the following:
Music—to select a music clip from the list.
Message—to edit the Opening message and Closing
message.
Videos & Images—select from the following:
• Add/Remove to add or remove video clips and
images, or Add/Remove > Capture to open the
camera application to capture new video clips and
images.
• Move to reorder the position of video clips and
images in the custom muvee.
• Select contents to select video segments to include/
exclude in the muvee.
• Length—to define the duration of the muvee, select
User defined. Select Multimedia message, Same as
music, or Auto-select. If the muvee duration is less
than the music duration, the muvee is repeated to
match the music duration. If the muvee duration is
longer than the music duration, the music is
repeated to match the muvee duration.
Settings—to change the settings for muvee production.
Select from the following:
• Memory in use—select where to store your muvees.
• Resolution—select the resolution of your muvees.
• Default muvee name—set a default name for the
muvees.
3 Select Create muvee.
The muvee is created automatically and a Preview muvee
view is displayed. You can select Save to save the muvee
in the Gallery, Recreate to shuffle the media files and
create a new muvee, or Customise to return to the muvee
settings.
Web browser
Various service providers maintain pages specifically
designed for mobile devices. These pages use the wireless
markup language (WML), extensible hypertext markup
language (XHTML), or hypertext markup language (HTML).
Check the availability of services, pricing, and fees with
your network operator or service provider. Service
providers will also give you instructions on how to use
their services.
Press , and select My own > Services.
With this additional browser, you are able to view normal
Web pages, to zoom in and out on a page (Mini Map), to
view Web pages that contain only text in narrow form so
that text wraps, and to read feeds and blogs.
To turn the Mini Map on or off for the current page, press
. When the Mini Map is on, an overview of the
My own
77
complete page is shown when you press and hold the
scroll key right, left, up, or down to move on the page.
See also ‘Web access point’, p. 65.
My own
Games
Press , and select My own and a game. For instructions
on how to play the game, select Options > Help.
78
FCC DRAFT
Connectivity
Bluetooth connectivity
You can connect wirelessly to other compatible devices
with wireless Bluetooth technology. Compatible devices
may include mobile phones, computers, and enhancements
such as headsets and car kits. You can use Bluetooth
connectivity to send images, video clips, music and sound
clips, and notes; connect wirelessly to your compatible PC
(for example, to transfer files); and connect to a
compatible printer to print images with Image print. See
‘Image print’, p. 37.
Since devices with Bluetooth technology communicate
using radio waves, your device and the other device do not
need to be in direct line-of-sight. The two devices only
need to be within 10 meters (33 feet) of each other, but the
connection may be subject to interference from
obstructions such as walls or from other electronic devices.
This device is compliant with Bluetooth Specification 2.0
supporting the following profiles: Basic Printing Profile,
Generic Access Profile, Serial Port Profile, Dial-up
Networking Profile, Headset Profile, Handsfree Profile,
Generic Object Exchange Profile, Object Push Profile, File
Transfer Profile, Basic Imaging Profile, SIM Access profile,
and Human Interface Device Profile. To ensure
interoperability between other devices supporting
Bluetooth technology, use Nokia approved enhancements
for this model. Check with the manufacturers of other
devices to determine their compatibility with this device.
Glossary: A profile corresponds to a service or a
function, and defines how different devices connect.
For example, the Handsfree Profile is used between the
handsfree device and the phone. For devices to be
compatible, they must support the same profiles.
There may be restrictions on using Bluetooth technology
in some locations. Check with your local authorities or
service provider.
Features using Bluetooth technology, or allowing such
features to run in the background while using other
features, increase the demand on battery power and
reduce the battery life.
When the device is locked, you cannot use Bluetooth
connectivity. See ‘Security’, p. 101 for more information
on locking the device.
FCC DRAFT
Connectivity
79
Settings
Press , and select Connect. > Bluetooth. When you
open the application for the first time, you are asked to
define a name for your device. After you set Bluetooth
connectivity on and change My phone's visibility to
Connectivity
Shown to all, your device and this name can be seen by
other users with devices using Bluetooth technology.
Select from the following:
Bluetooth—Select On or Off. To connect wirelessly to
another compatible device, first set Bluetooth
connectivity On, then establish a connection.
My phone's visibility—To allow your device to be found
by other devices with Bluetooth technology, select Shown
to all. To hide it from other devices, select Hidden.
My phone's name—Edit the name of your device.
Remote SIM mode—To enable another device, such as a
compatible car kit enhancement, to use the SIM card in
your device to connect to the network, select On.
Remote SIM mode
To use the remote SIM mode with a compatible car kit
enhancement, set Bluetooth connectivity on, and enable
the use of the remote SIM mode with your device. Before
the mode can be activated, the two devices must be
paired and the pairing initiated from the other device.
When pairing, use a 16-digit passcode, and set the other
device as authorized. See ‘Pair devices’, p. 81. Activate the
remote SIM mode from the other device.
When the remote SIM mode is on in your Nokia N93,
Remote SIM is displayed in the standby mode. The
connection to the wireless network is turned off, as
indicated by in the signal strength indicator area, and
you cannot use SIM card services or features requiring
cellular network coverage. However, a wireless LAN
connection remains active during the remote SIM mode.
Warning: In the remote SIM mode, you cannot
make or receive any calls with your device, except make
calls to certain emergency numbers, or use other
features that require network coverage. To make calls,
you must first exit the remote SIM mode. If the device
has been locked, enter the lock code.
To exit the remote SIM mode, press the power key, and
select Exit rem. SIM mode.
Security tips
When you are not using Bluetooth connectivity, select
Bluetooth > Off or My phone's visibility > Hidden.
Do not pair with an unknown device.
80
Send data using Bluetooth connectivity
Several Bluetooth connections can be active at a time. For
example, if you are connected to a headset, you can also
transfer files to another compatible device at the same
time.
Bluetooth connectivity indicators
• When is shown in the standby mode, Bluetooth
connectivity is on.
• When is blinking, your device is trying to connect
with another device.
• When is shown continuously, data is being
transmitted using Bluetooth connectivity.
1 Open the application where the item you want to send
is stored. For example, to send an image to another
compatible device, open Gallery.
2 Select the item and Options > Send > Via Bluetooth.
Devices with Bluetooth technology within range start
to appear on the display.
Device icons are: computer, phone, audio or
video device, and other device.
To interrupt the search, select Stop.
3 Select the device with which you want to connect.
4 If the other device requires pairing before data can be
transmitted, a tone sounds, and you are asked to enter
a passcode. See ‘Pair devices’, p. 81.
5 When the connection has been established, Sending
data is shown.
The Sent folder in Messag. does not store messages sent
using Bluetooth connectivity.
Tip! When searching for devices, some devices may
show only the unique address (device address). To find
the unique address of your device, enter the code
*#2820# in the standby mode.
Pair devices
To open the paired devices view (), in the Bluetooth
application main view, press .
Before pairing, create your own passcode (1—16 digits),
and agree with the owner of the other device to use the
same code. Devices that do not have a user interface have
a factory-set passcode. The passcode is used only once.
To pair with a device, select Options > New paired
device. Devices with wireless Bluetooth technology within
range start to appear on the display. Select the device, and
enter the passcode. The same passcode must be entered
on the other device as well. After pairing, the device is
saved to the paired devices view.
Paired devices are indicated by in the device search.
To set a device as authorized or unauthorized, scroll to a
device, and select from the following options:
Set as authorised—Connections between your device and
this device can be made without your knowledge. No
Connectivity
FCC DRAFT
81
separate acceptance or authorization is needed. Use this
status for your own devices, such as your compatible
headset or PC, or devices that belong to someone you
trust. indicates authorized devices in the paired
devices view.
Set as unauthorised—Connection requests from this
Connectivity
device must be accepted separately every time.
To cancel a pairing, scroll to the device, and select
Options > Delete. If you want to cancel all pairings, select
Options > Delete all.
Tip! If you are currently connected to a device and
delete the pairing with that device, pairing is removed
immediately, and the connection is switched off.
Receive data using Bluetooth
connectivity
When you receive data through Bluetooth connectivity, a
tone sounds, and you are asked if you want to accept the
message. If you accept, is shown, and the item is
placed in the Inbox folder in Messag.. Messages received
through Bluetooth connectivity are indicated by . See
‘Inbox—receive messages’, p. 43.
Switch off Bluetooth connectivity
To switch off Bluetooth connectivity, select Bluetooth >
Off.
Infrared connection
With infrared, you can transfer data such as business
cards, calendar notes, and media files with a compatible
device.
Do not point the infrared (IR) beam at anyone's eye or
allow it to interfere with other IR devices. This device is a
Class 1 laser product.
Send and receive data using infrared
1 Ensure that the infrared ports of the sending and
receiving devices are pointing at each other, and that
there are no obstructions between the devices. The
preferable distance between the two devices is up to 1
meter (3 feet).
2 The user of the receiving device activates the infrared
port.
To activate the infrared port of your device to receive
data through infrared, press , and select Connect. >
Infrared.
3 The user of the sending device selects the desired
infrared function to start the data transfer.
82
To send data through infrared, locate the desired file in
an application or the file manager, and select
Options > Send > Via infrared.
If data transfer is not started within 1 minute after the
activation of the infrared port, the connection is cancelled
and must be started again.
All items received through infrared are placed in the Inbox
folder in Messaging. New infrared messages are indicated
by .
When blinks, your device is trying to connect to the
other device or a connection has been lost.
When is shown continuously, the infrared
connection is active, and your device is ready to send and
receive data using its infrared port.
Data cbl.
Press , and select Connect. > Data cbl.. In Data cable
mode, select what the USB data cable connection is used
for: PC Suite, Data transfer, or Image print. To have the
device ask the purpose of the connection each time the
cable is connected, select Ask on connection.
PC connections
You can use your device with a variety of PC connectivity
and data communications applications. With Nokia PC
Suite you can, for example, transfer images between your
device and a compatible PC.
Always create the connection from the PC to synchronize
with your device.
Your device as a modem
You can use your device as a modem to send and receive
e-mail, or to connect to the Internet with a compatible PC
by using Bluetooth connectivity, infrared, or a USB data
cable. Detailed installation instructions can be found in
the User Guide for Nokia PC Suite.
Tip! When using Nokia PC Suite for the first time, to
connect your device to a compatible PC and to use
Nokia PC Suite, use the Get Connected wizard available
in Nokia PC Suite.
Connection manager
Press , and select Connect. > Conn mgr. To view the
status of data connections or end connections in GSM and
UMTS network and wireless LAN, select Act. data conn..
Connectivity
FCC DRAFT
83
To search for wireless LANs available within range, select
Availab. WLAN.
Synchronization
Data connections
In the active connections view, you can see the open data
Connectivity
connections: data calls ( ), packet data connections (
or ), and wireless LAN connections ().
To end a connection, select Options > Disconnect. To
close all open connections, select Options > Disconnect
all.
To view the details of a connection, select Options >
Details. The details shown depend on the connection type.
Wireless LAN
The available wireless LAN view shows a list of wireless
LANs within range, their network mode (Infrastructure or
Ad-hoc), and signal strength indicator. is shown for
networks with encryption, and if your device has an
active connection in the network.
To view the details of a network, select Options > Details.
To create an Internet access point in a network, select
Options > Define access point.
84
Note: The actual time invoiced for calls by your
service provider may vary, depending on network
features, rounding off for billing, and so forth.
Press , and select Connect. > Sync. Sync enables you
to synchronize your notes, calendar, contacts, or e-mail
with various compatible calendar and address book
applications on a compatible computer or on the Internet.
You can also create or edit synchronization settings.
The synchronization application uses SyncML technology
for synchronization. For information on SyncML
compatibility, contact the supplier of the application with
which you want to synchronize your device data.
You may receive synchronization settings in a special text
message. See ‘Data and settings’, p. 44.
Synchronize data
In the Sync main view, you can see the different
synchronization profiles.
1 Select a synchronization profile and Options >
Synchronise. The status of the synchronization is
shown on the display.
To cancel synchronization before it finishes, select
Cancel.
2 You are notified when the synchronization is complete.
Select Yes to view the log file showing the
synchronization status and how many entries have
been added, updated, deleted, or discarded (not
synchronized) in your device or on the server.
Device manager
Press , and select Connect. > Dev. mgr.. You may
receive server profiles and different configuration settings
from your network operator, service provider, or company
information management department. These configuration
settings may include access point settings for data
connections and other settings used by different
applications in your device.
To connect to a server and receive configuration settings
for your device, scroll to a profile, and select Options >
Start configuration.
To allow or deny receiving of configuration settings from
service providers, select Options > Enable config. or
Disable config..
Server profile settings
Contact your service provider for the correct settings.
Server name—Enter a name for the configuration server.
Server ID—Enter the unique ID to identify the
configuration server.
Server password—Enter a password to identify your
device to the server.
Access point—Select an access point to be used when
Auto-accept all reqs.—If you want your device to ask for
confirmation before accepting a configuration from the
server, select No.
Home network
Your device is compatible with Universal Plug and Play
architecture (UPnP). Using a wireless LAN access point
device or a wireless LAN router, you can create a home
network and connect compatible UPnP devices that
support wireless LAN to the network, such as your Nokia
N93, a compatible PC, a compatible printer, and a
compatible sound system or a TV, or a sound system or TV
equipped with a compatible wireless multimedia receiver.
Connectivity
FCC DRAFT
85
Using the wireless LAN function of the Nokia N93 in a
home network requires a working wireless LAN home
connection setup and the other target home devices to be
UPnP enabled and to be connected to the same home
network.
You can share media files saved in Gallery with other
Connectivity
compatible UPnP devices using the home network. To
manage your Home network settings, press , and
select Connect. > Home network. You can also use the
home network to view, play, copy, or print compatible
media files from Gallery. See ‘View media files’, p. 87.
Home network settings
To share media files saved in Gallery with other
compatible UPnP devices through wireless LAN, you must
first create and configure your wireless LAN home
Internet access point, and then configure the Home
network application. See ‘Wireless LAN’, p. 15.
The options related to Home network are not available in
Gallery before the Home network settings have been
configured.
Configure settings
To configure the Home network application, select
Connect. > Home network > Settings, and from the
following:
Home access point—Select Always ask if you want the
device to ask for the home access point every time you
connect to the home network, User defined to select your
home Internet access point that is used automatically
when you use Home network, or None. If your home
network does not have wireless LAN security settings
enabled, you get a security warning. You can continue, and
switch the wireless LAN security on later; or cancel
defining the access point, and first switch on the wireless
LAN security. See Wireless LAN in ‘Access points’, p. 98.
My device name— Enter a name for your device that is
shown to the other compatible devices in the home
network.
Set sharing on and define content
Select Connect. > Home network > Share content.
Content sharing—Allow or deny sharing media files with
compatible devices. Do not set Content sharing on before
you have configured all the other settings. If you set
Content sharing on, the other UPnP compatible devices in
the home network can view and copy your files you have
selected for sharing in the Images & video and Music
folders.
To select media files for sharing with other devices from
the Images & video and Music folders, or to view the
sharing status of Images & video or Music, select Share
content.
86
View media files
To connect a compatible PC to the home network, you
must install the related software from the DVD-ROM
supplied with your Nokia N93.
If Content sharing is on in your device, the other UPnP
compatible devices in the home network can view and
copy the media files you have selected to share in Share
content. If you do not want the other devices to access
your files, set Content sharing off. Even if Content
sharing is off in your device, you can still view and copy
the media files stored in another home network device if it
is allowed by the other device.
Show media files stored in your device
To select images, videos, and sound clips stored in your
device, and show them in another home network device,
such as a compatible TV, do the following:
1 In Gallery, select an image, a video clip, or a sound clip.
2 Select Options > Show via home net.
3 Select a compatible device in which the media file is
shown. The images are shown both in the other home
network device and your device, and the video clips and
sound clips are played only in the other device.
Show media files stored in the other device
To select media files that are stored on another home
network device, and show them in your device (or in a
compatible TV, for example), do the following:
1 In Gallery, select Home network. Your device starts
the search of other compatible devices. Device names
start to appear on the display.
2 Select a device from the list.
3 Select the type of media you want to view from the
other device. The available file types depend on the
features of the other device.
4 Select the image, video clip, or music clip you want to
view, and select Options > Show via home net.
(images and video) or Play via home network (music).
5 Select the device in which the file is shown.
To stop sharing the media file, select Options > Stop
showing.
To print images saved in Gallery through Home network
with a UPnP compatible printer, select the print option in
Gallery. See ‘Image print’, p. 37. Content sharing does not
have to be switched on.
To search files with different criteria, select Options >
Find. To sort the found files, select Options > Sort by.
Connectivity
FCC DRAFT
87
Copy media files
To copy or transfer media files from your device to another
compatible device, such as a UPnP compatible PC, select
a file in Gallery, and Options > Organise > Copy to home
network or Move to home network. Content sharing
Connectivity
does not have to be switched on.
To copy or transfer files from the other device to your
device, select a file in the other device, and Options >
Copy to phone mem. or Copy to memory card (the name
of the memory card if the memory card is available).
Content sharing does not have to be switched on.
88
Office
Calculator
To add, subtract, multiply, divide, and calculate square
roots and percentages, press , and select Office >
Calculator.
Note: This calculator has limited accuracy and is
designed for simple calculations.
Office
Set base currency and exchange rates
Select Type > Currency > Options > Currency rates.
Before you can make currency conversions, you must
select a base currency and add exchange rates. The rate of
the base currency is always 1.
Note: When you change base currency, you must
enter the new rates because all previously set
exchange rates are cleared.
Converter
To convert measures from one unit to another, press ,
and select Office > Converter.
Converter has limited accuracy, and rounding errors may
occur.
1 In the Type field, select the measure you want to use.
2 In first Unit field, select the unit from which you want
to convert. In the next Unit field, select the unit to
which you want to convert.
3 In the first Amount field, enter the value you want to
convert. The other Amount field changes automatically
to show the converted value.
Notes
To write notes, press , and select Office > Notes. You
can send notes to compatible devices, and save plain text
files (.txt format) that you receive to Notes.
To print a note on a compatible Basic Print Profile (BPP)
equipped printer with Bluetooth connectivity (such as HP
Deskjet 450 Mobile Printer or HP Photosmart 8150), select
Options > Print.
FCC DRAFT
89
Recorder
Office
To record voice memos, press , and select Office >
Recorder. To record a telephone conversation, open
Recorder during a voice call. Both parties hear a tone
every 5 seconds during recording.
Quickoffice
To use the Quickoffice applications, press , and select
Office > Quickoffice. A list of files in the .doc, .xls, .ppt,
and .txt file formats saved in your device opens.
To open a file in its respective application, press . To
sort files, select Options > Sort files.
To open Quickword, Quicksheet, or Quickpoint, press
to reach the desired view.
Quickword
With Quickword, you can view native Microsoft Word
documents on the display of your device. Quickword
supports colors, bold, italics, and underline.
Quickword supports the viewing of documents saved in
.doc format in Microsoft Word 97, 2000, and XP. Not all
variations or features of the mentioned file formats are
supported.
See also ‘More information’, p. 91.
View Word documents
To move in the document, use the scroll key.
To search the document for text, select Options > Find.
You can also select Options and from the following:
Go to—to move to the start, end, or selected position
within the document
Zoom—to zoom in or out
Autoscroll—to start automatic scrolling through the
document. To stop scrolling, press .
Quicksheet
With Quicksheet, you can read Microsoft Excel files on the
display of your device.
Quicksheet supports the viewing of spreadsheet files
saved in .xls format in Microsoft Excel 97, 2000, 2003, and
XP. Not all variations or features of the mentioned file
formats are supported.
See also ‘More information’, p. 91.
90
View spreadsheets
To move around in the spreadsheet, use the scroll key.
To switch between worksheets, select Options >
Worksheet.
To search the speadsheet for a text within a value or
formula, select Options > Find.
To change how the spreadsheet is displayed, select
Options and from the following:
Pan—to navigate within the current worksheet by blocks.
A block contains columns and rows displayed by a screen.
To display the columns and rows, use the scroll key to
select a block and OK.
Zoom—to zoom in or out
Freeze—to keep the highlighted row, column, or both
visible while you move in the spreadsheet
Resize—to adjust the size of columns or rows
Quickpoint
With Quickpoint, you can view Microsoft PowerPoint
presentations on the display of your device.
Quickpoint supports the viewing of presentations created
in .ppt format in Microsoft PowerPoint 97, 2000, and XP.
Not all variations or features of the mentioned file formats
are supported.
See also ‘More information’, p. 91.
View presentations
To move between the slide, outline, and the notes view,
press or .
To move to the next or previous slide in the presentation,
press or .
To view the presentation in full screen, select Options >
Full screen.
To expand items in the presentation outline in the outline
view, select Options > Expand entry.
More information
If you experience problems with Quickword, Quicksheet,
or Quickpoint, visit www.quickoffice.com for more
information. Support is also available by sending an
e-mail to supportS60@quickoffice.com.
Office
FCC DRAFT
91
Personalize your device
Your service provider may have requested that certain
features be disabled or not activated in your device. If so,
they will not appear on your device menu. Your device
may also have been specially configured for your network
provider. This configuration may include changes in menu
names, menu order, and icons. Contact your service
provider for more information.
• To use the standby display for fast access to your most
Personalize your device
92
frequently used applications, see ‘Active standby
mode’, p. 94.
• To change the standby
mode background image
or what is shown in the
screen saver, see ‘Change
the look of your device’,
p. 93.
• To customize the ringing
tones, see ‘Profiles—set
tones’, p. 92 and ‘Add
ringing tones for
contacts’, p. 64.
• To change the shortcuts
assigned for the different
presses of the scroll key and left and right selection
keys in the standby mode, see ‘Standby mode’, p. 96.
FCC DRAFT
• To change the clock shown in the standby mode, press
, and select Clock > Options > Settings > Clock
type > Analogue or Digital.
• To change the welcome note to an image or animation,
press , and select Tools > Settings > Phone >
General > Welcome note / logo.
• To change the main menu view, in the main menu,
select Options > Change view > Grid or List.
• To rearrange the main menu, in the main menu, select
Options > Move, Move to folder, or New folder. You
can move less used applications into folders, and place
applications that you use more often into the main
menu.
Profiles—set tones
To set and customize the ringing tones, message alert
tones, and other tones for different events, environments,
or caller groups, press , and select Tools > Profiles.
To change the profile, press in the standby mode.
Scroll to the profile you want to activate, and select OK.
To modify a profile, press , and select Tools > Profiles.
Scroll to the profile, and select Options > Personalise.
Scroll to the setting you want to change, and press to
open the choices. Tones stored on the memory card are
indicated with . You can scroll through the tone list
and listen to each one before you make your selection. To
stop the sound, press any key.
When you choose a tone, Tone downloads opens a list of
bookmarks. You can select a bookmark and start
connection to a Web page to download tones.
If you want the caller’s name to be said when your device
rings, select Options > Personalise, and set Say caller’s
name to On. The caller’s name must be saved in Contacts.
To create a new profile, select Options > Create new.
Offline profile
The Offline profile lets you use the device without
connecting to the wireless network. When you activate the
Offline profile, the connection to the wireless network is
turned off, as indicated by in the signal strength
indicator area. All wireless phone signals to and from the
device are prevented. If you try to send messages, they are
placed in the outbox to be sent later.
Warning: In the offline profile you cannot make (or
receive) any calls, except make calls to certain
emergency numbers, or use other features that require
network coverage. To make calls, you must first activate
the phone function by changing profiles. If the device
has been locked, enter the lock code.
Warning: Your device must be switched on to use
Offline profile. Do not switch the device on when
wireless device use is prohibited or when it may cause
interference or danger.
When you have activated the Offline profile, you can still
use the wireless LAN (if available), for example, to read
your e-mail or browse on the Internet. Remember to
comply with any applicable safety requirements when
establishing and using a wireless LAN connection. See
‘Wireless LAN’, p. 15.
To exit the Offline profile, press the power key, and select
another profile. The device reenables wireless
transmissions (providing there is sufficient signal
strength). If a Bluetooth connection is activated before
using the Offline profile, it is deactivated. A Bluetooth
connection is automatically reactivated after you exit the
Offline profile. See ‘Settings’, p. 80.
Change the look of your
device
To change the look of the display, such as the wallpaper
and icons, press , and select Tools > Themes. The active
theme is indicated by . In Themes you can group
Personalize your device
93
together elements from other themes or select images
from the Gallery to personalize themes further. The
themes on the memory card (if inserted) are indicated by
. The themes on the memory card are not available if
the memory card is not inserted in the device. If you want
to use the themes saved in the memory card without the
memory card, save the themes in the device memory first.
To open a browser connection and download more
themes, select Theme downloads.
To activate a theme, scroll to it, and select Options >
Personalize your device
Apply. To preview a theme before activating it, select
Options > Preview.
To edit themes, scroll to a theme, and select Options >
Edit to change the Wallpaper and Power saver settings.
To restore the selected theme to its original settings,
select Options > Restore orig. theme when you edit a
theme.
Active standby mode
Use your standby display for fast access to your most
frequently used applications. By default, the active
standby mode is on.
Press , select Tools > Settings > Phone > Standby
mode > Active standby, and press to switch the
active standby on or off.
The active standby display is
shown with default
applications across the top of
the screen, and calendar,
to-do, and player events
listed below.
Scroll to an application or
event, and press .
The standard scroll key
shortcuts available in the
standby mode cannot be used
when the active standby
mode is on.
To change the default applications shortcuts, press ,
select Tools > Settings > Phone > Standby mode >
Active standby apps., and press .
Some shortcuts may be fixed, and you are not able to
change them.
94
FCC DRAFT
Tools
Media Key
To open the shortcut assigned to the multimedia key, press
and hold . To open a list of multimedia applications,
press . To open the desired application, use the scroll
key. To exit the list without selecting an application, press
and hold .
To change the shortcuts, press , and scroll down. To
change the default shortcut, select Multimedia key. To
change the applications that are shown when you press
, select Top, Left, Middle, and Right and the
application.
Some shortcuts may be fixed, and you are not able to
change them.
Settings
To change settings, press , and select Tools > Settings.
To open a settings group, press . Scroll to a setting you
want to change, and press .
Tools
Some settings may be preset for the device by your
network operator or service provider, and you may not be
able to change them.
Phone settings
General
Phone language—Changing the language of the display
texts in your device also affects the format used for date
and time and the separators used, for example, in
calculations. Automatic selects the language according to
the information on your SIM card. After you change the
display text language, the device restarts.
Changing the settings for Phone language or Writing
language affects every application in your device, and the
change remains effective until you change these settings
again.
Writing language—Changing the language affects the
characters and special characters available when writing
text and the predictive text dictionary used.
FCC DRAFT
95
Predictive text—Set the predictive text input On or Off
for all editors in the device. The predictive text dictionary
Tools
is not available for all languages.
Welcome note / logo—The welcome note or logo is
displayed briefly each time you switch on the device.
Select Default to use the default image, Text to write a
welcome note, or Image to select an image from Gallery.
Orig. phone settings—You can reset some of the settings
to their original values. To do this, you need the lock code.
See ‘Security’, ‘Phone and SIM’, p. 102. After resetting, the
device may take a longer time to power on. Documents
and files are unaffected.
Cover display
Personalization:
Wallpaper—Select the background image displayed on
the cover display in the standby mode. If you select User
defined in the wallpaper settings, the cropping tool frame
is shown on top of the image you selected. The cropping
tool frame is the size of the cover display, and you can
zoom, rotate, and crop the area of the image you want to
be displayed on the cover display.
Closing animation—Select a short animation to play
when you close the cover.
Closing tone—Select a short tune to play when you close
the cover.
Opening sound—Select a short tune to play when you
open the cover and the device is in the standby mode.
Calls:
Answer if fold opened—Select No or Yes.
If fold closed—Select End call or Activate loudspeaker.
Standby mode
Active standby—Use shortcuts to applications in the
standby mode. See ‘Active standby mode’, p. 94.
Left selection key—Assign a shortcut to the left selection
key () in the standby mode.
Right selection key—Assign a shortcut to the right
selection key () in the standby mode.
Active standby apps.—Select the application shortcuts
you want to appear in the active standby. This setting is
only available if Active standby is on.
You can also assign keypad shortcuts for the different
presses of the scroll key. The scroll key shortcuts are not
available if the active standby is on.
Operator logo—This setting is only available if you have
received and saved an operator logo. Select Off if you do
not want the logo to be shown.
96
Display
Brightness—Adjust the basic brightness level of the display
to lighter or darker. However, in extreme light conditions,
the brightness of the display is automatically adjusted.
Power saver time-out—Select the time-out period after
which the screen saver is activated.
Light time-out—Select a time-out after which the
backlight of the display is switched off.
Power saver—Select whether the display is switched off to
save battery power 20 minutes after the screen saver is
activated. When the display is switched off, a LED blinks to
indicate that the device is powered on.
TV configuration
TV system—Select PAL for PAL and SECAM TV system
format or NTSC for NTSC TV system format.
Ratio—Select 4:3 or 16:9.
Call settings
Send my caller ID—You can set your phone number to be
displayed to (Yes) or hidden from (No) the person to whom
you are calling, or the value may be set by your network
operator or service provider when you make a subscription
(Set by network) (network service).
Call waiting—If you have activated call waiting (network
service), the network notifies you of a new incoming call
while you have a call in progress. Set the function on
(Activate) or off (Cancel), or check whether the function
is activated (Check status).
Reject call with SMS—Select Yes to send a text message
to a caller informing why you could not answer the call.
See ‘Answer or reject a call’, p. 58.
Message text—Write a text to be sent in a text message
when you reject a call.
Automatic redial—Select On, and your device makes a
maximum of 10 attempts to connect the call after an
unsuccessful call attempt. To stop automatic redialing,
press .
Summary after call—Activate this setting if you want the
device to briefly display the approximate duration of the
last call.
Speed dialling—Select On, and the numbers assigned to
the speed dialing keys ( - ) can be dialed by
pressing and holding the key. See also ‘Speed dial a phone
number’, p. 53.
Tools
FCC DRAFT
97
Anykey answer—Select On, and you can answer an
incoming call by briefly pressing any keypad key, except
Tools
, , , and .
Line in use—This setting (network service) is shown only
if the SIM card supports two subscriber numbers, that is,
two phone lines. Select which phone line you want to use
for making calls and sending text messages. Calls on both
lines can be answered irrespective of the selected line. If
you select Line 2 and have not subscribed to this network
service, you will not be able to make calls. When line 2 is
selected, is shown in the standby mode.
Tip! To switch between the phone lines, press and
hold in the standby mode.
Line change—To prevent line selection (network service),
select Disable if supported by your SIM card. To change
this setting, you need the PIN2 code.
Connection
Data connections and access points
Your device supports packet data connections, such as
GPRS in the GSM network. When you use your device in
GSM and UMTS networks, multiple data connections can
be active at the same time, and access points can share a
data connection.
You can also use a wireless LAN data connection. See
‘Wireless LAN’, p. 15. Only one connection in one wireless
LAN can be active at a time.
To establish a data connection, an access point is required.
You can define different kinds of access points, such as:
• MMS access point to send and receive multimedia
messages
• Access point for the Web application to view WML or
XHTML pages
• Internet access point (IAP) to send and receive e-mail
and connect to the Internet
Check the type of access point you need with your service
provider for the service you want to access. For availability
and subscription to packet data connection services,
contact your network operator or service provider.
Access points
You may receive access point settings in a message from a
service provider. See ‘Data and settings’, p. 44. Some or all
access points may be preset for your device by your service
provider or network operator, and you may not be able to
change, create, edit, or remove them. indicates a
protected access point.
indicates a packet data access point, and a
wireless LAN access point.
98
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.