Microsoft RM-216V User Manual
Nokia 6131 NFC User Guide
RAFT
D
FCC Draft
Issue 1
DECLARATION OF CONFORMITY
Hereby, NOKIA CORPORATION declares that this RM -216 product is in c ompliance with the ess ential
requirements and other relevant provisions of Directive 1999/5/EC.
A copy of the Declaration of Conformity can be found from
http://www.nokia.com/phones/declaration_of_conformity/.
0434
The crossed-out wheeled bin means that within the European Union the product must be taken
to separate collection at the product end-of life. This applies to your device but also to any
enhancements marked with this symbol. Do not dispose of these products as unsorted
municipal w aste.
Copyright © 2007 Nokia. All rights reserv ed.
Reproduction, transfer, distribution or storage of part or all of the contents in this document in any form
without the prior written permission of Nokia is prohibited.
Nokia, Visual Radio, Nokia Connecting People, Navi, Xpress-on, XpressPrint, and Pop-Port are trademarks
or registered trademarks of Nokia Corporation. Other product and company names mentioned herein may
be trademarks or tradenames of their respective owners.
Nokia tune is a sound mark of Nokia Corporation.
US Patent No 5818437 and other pending patents. T9 text input software Copyright (C) 1997-2006. Tegic
Communic ations, Inc. All rights reserved.
Includes RSA BSAFE cryptographic or security protocol software from RSA Security.
Java is a trademark of Sun Microsystems, Inc.
This product is licensed under the MPEG-4 Visual Patent Portfolio License (i) for personal and
noncommercial use in connection with information which h as been encoded in compliance with the
MPEG-4 Visual Standard by a consumer engaged in a personal and noncommercial activity and (ii) for use
in connection with MPEG-4 video provided by a licensed video provider. No license is granted or shall be
implied for any other use. Additional information including that relating to promotional, internal and
commercial uses may be obtaine d from MPEG LA, LLC. See <http://www.mpegla.com>.
Nokia operates a policy of continuous development. Nokia reserves the right to make changes and
improvements to any of the products described in this document without prior notice.
This Nokia device complies with Directive 2002/95/EC on the restriction of the use of certain hazardous
substances in electrical and electronic equipment.
Under no circumstances shall Nokia be responsible for any loss of data or income or any special,
incidental, c onsequential or indirect damages howsoever caused.
D
RAFT
The contents of this document are provided "as is". Except as required by applicable law, no warranties of
any kind, either exp ress or implied, inc luding, but not limited to, the im plied warranties of
merchantability and fitness for a particular purpose, are made in relation to the accuracy, reliability or
contents of this document. Nokia reserves the right to revise this document or withdraw it at any time
without prior notice.
The availability of particular products may vary by region. Please check with the Nokia dealer nearest to
you.
This device may contain commodities, technology or software subject to export laws and regulations from
the US and other countries. Diversion contrary to law is prohibited.
FCC/INDUSTR Y CANADA NOTICE
Your device may cause TV or radio interference (for example, when using a telephone in close proximity to
receiving equipment). The FCC or Industry Canada can require you to stop using your telephone if such
interference cannot be eliminated. If you require assistance, contact your local service facility. This device
complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This
device may n ot cause harmful interference, and (2) this de vice must accept any interference received,
including interference that may cause undesired operation. Any changes or modifications not expressly
approved by Nokia could void the user's authority to operate this equipment.
FCC-Draft/Issue 1
RAFT
D
Contents
For your safety................................. 6
General information ........................ 9
Overview of functions ..................................... 9
Access codes ...................................................... 9
Configuration settings service ................... 10
Download content ......................................... 11
Software updates........................................... 11
Nokia support ................................................. 12
1. Get started.................................. 12
Install SIM card and battery....................... 12
Insert a microSD card................................... 13
Remove the microSD card........................... 14
Charge the battery ........................................ 14
Open and close the phone .......................... 15
Switch the phone on and off ..................... 15
Antenna............................................................ 16
Phone strap ..................................................... 16
2. Your phone ................................. 17
Keys and parts ................................................ 17
Standby mode................................................. 18
Keypad lock (keyguard) ................................ 21
Functions without a SIM card ................... 21
3. Call functions............................. 21
Make a call ...................................................... 21
Answer or reject a call ................................. 23
Options during a call .................................... 24
4. Write text ................................... 24
Predictive text input ..................................... 25
Traditional text input ................................... 25
5. Navigate the menus................... 26
6. Messaging................................... 27
Text messages (SMS) .................................... 27
SIM messages ................................................. 29
Multimedia messages (MMS)..................... 29
Memory full..................................................... 31
Folders............................................................... 32
D
RAFT
Postcards .......................................................... 32
Flash messages ............................................... 33
Nokia Xpress audio messaging ................... 33
E-mail application ......................................... 34
Instant messaging.......................................... 37
Voice messages ............................................... 42
Info messages.................................................. 42
Service commands ......................................... 42
Delete messages ............................................. 43
Message settings ............................................ 43
7. Contacts ..................................... 46
Search for a contact...................................... 46
Save names and phone numbers ............... 46
Save details...................................................... 47
Transmit a call request to a service tag.. 47
Copy or move contacts................................. 47
Edit contact details........................................ 48
Synchronize all................................................ 48
Delete contacts............................................... 48
My presence..................................................... 48
Subscribed names .......................................... 49
Business cards................................................. 51
Settings ............................................................. 51
Groups ............................................................... 52
Speed dials ....................................................... 52
Info, service, and my numbers.................... 52
8. Call log ....................................... 52
Positioning information ............................... 53
9. Settings ..................................... 53
Profiles .............................................................. 53
Themes .............................................................. 54
Tones.................................................................. 54
Main display .................................................... 55
Mini display ..................................................... 56
Time and date.................................................. 56
My shortcuts.................................................... 56
Connectivity..................................................... 58
Call ..................................................................... 63
Phone................................................................. 64
4
Enhancements ................................................ 65
Configuration.................................................. 66
Security............................................................. 67
Phone software updates .............................. 68
Restore factory settings............................... 69
10. Operator menu ........................ 69
11. Gallery...................................... 69
Print images .................................................... 70
Memory card................................................... 70
12. Media ....................................... 71
Camera.............................................................. 71
Media player ................................................... 73
Music player.................................................... 73
Radio ................................................................. 75
Voice recorder................................................. 76
Equalizer........................................................... 77
Stereo widening ............................................. 77
13. Organizer.................................. 78
Alarm clock...................................................... 78
Calendar ........................................................... 78
To-do list.......................................................... 79
Notes ................................................................. 80
Calculator......................................................... 80
Countdown timer........................................... 81
Stopwatch........................................................ 81
14. Push to talk ............................. 82
Push to talk channels ................................... 82
Switch PTT on and off .................................. 83
Make and receive a PTT call ....................... 84
Callback requests........................................... 86
Add a one-to-one contact .......................... 87
PTT settings ..................................................... 87
Configuration settings ................................. 88
Web.................................................................... 88
15. Applications............................. 88
Launch a game ............................................... 88
Launch an application.................................. 89
Some application options............................ 89
D
RAFT
Download an application ............................. 89
Presenter........................................................... 90
Secure applications ....................................... 91
16. SIM services............................. 91
17. Web.......................................... 92
Set up browsing.............................................. 92
Connect to a service...................................... 92
Browse pages .................................................. 93
Bookmarks........................................................ 94
Appearance settings...................................... 94
Security settings............................................. 95
Download settings ......................................... 96
Service inbox ................................................... 96
Cache memory ................................................ 97
Browser security ............................................. 97
18. NFC .......................................... 99
Near Field Communication.......................... 99
Tag detection on or off................................. 99
NFC detection .............................................. 100
Service tags................................................... 100
Payment and ticketing............................... 100
Read service tags......................................... 101
Transmit to service tags ............................ 101
19. PC connectivity ..................... 102
Nokia PC Suite ............................................. 102
EGPRS, HSCSD, and CSD ........................... 102
Data communication applications ......... 103
20. Battery information.............. 103
Charging and discharging ......................... 103
Nokia battery authentication .................. 104
21. Technical Information........... 107
Care and maintenance................. 108
Additional safety information.... 109
APPENDIX..................................... 113
Index............................................. 122
5
For your safety
For your safety
Read these simple guidelines. Not following them may be dangerous or illegal.
Read the complete user guide for further information.
SWITCH ON SAFELY
Do not switch the phone on when wireless phone use is prohibited or
when it may cause interference or danger.
ROAD SAFETY COMES FIRST
Obey all local laws. Always keep your hands free to operate the
vehicle while driving. Your first consideration while driving should be
road safety.
INTERFERENCE
All wireless phones may be susceptible to interference, which could
affect performance.
SWITCH OFF IN HOSPITALS
Follow any restrictions. Switch the phone off near medical
equipment.
SWITCH OFF IN AIRCRAFT
Follow any restrictions. Wireless devices can cause interference in
aircraft.
SWITCH OFF WHEN REFUELLING
Do not use the phone at a refuelling point. Do not use near fuel or
chemicals.
SWITCH OFF NEAR BLASTING
Follow any restrictions. Do not use the phone where blasting is in
progress.
USE SENS IBLY
D
Use only in the normal position as explained in the product
documentation. Do not touch the antenna unnecessarily.
QUALIFIED SERVICE
Only qualified personnel may install or repair this product.
RAFT
ENHANCEMENTS AND BATTERIES
Use only approved enhancements and batteries. Do not connect
incompatible products.
6
For your safety
WATER-RESISTANCE
Your phone is not water-resistant. Keep it dry.
BACK-UP COPIES
Remember to make back-up copies or keep a written record of all
important information stored in your phone.
CONNECTING TO OTHER DEVICES
When connecting to any other device, read its user guide for detailed
safety instructions. Do not connect incompatible products.
EMERGENCY CALLS
Ensure the phone is switched on and in service. Press the end key as
many times as needed to clear the display and return to the start
screen. Enter the emergency number, then press the call key. Give
your location. Do not end the call until given permission to do so.
■ About your device
The wireless device described in this guide is approved for use on the EGSM 850,
900, 1800 and 1900 networks. Contact your service provider for more
information about networks.
When using the features in this device, obey all laws and respect the privacy and
legitimate rights of others.
When taking and using images or video clips, obey all laws and respect local
customs as well as privacy and legitimate rights of others.
Warning: To use any features in this device, other than the alarm clock
and the NFC tag detection, if the activation level is set to ’always on’,
the device must be switched on. Do not switch the device on when
wireless device use may cause interference or danger.
RAFT
D
■ Network services
To use the phone you must have service from a wireless service provider. Many of
the features in this device depend on features in the wireless network to
function. These network services may not be available on all networks or you may
have to make specific arrangements with your service provider before you can
utilize network services. Your service provider may need to give you additional
instructions for their use and explain what charges will apply. Some networks
may have limitations that affect how you can use network services. For instance,
some networks may not support all language-dependent characters and services.
7
For your safety
Your service provider may have requ ested that certain features be disabled or not
activated in your device. If so, they will not appear on your device menu. Your
device may also have been specially configured for your network provider. This
configuration may include changes in menu names, menu order and icons.
Contact your service provider for more information.
This device supports WAP 2.0 protocols (HTTP and SSL) that run on TCP/IP
protocols. Some features of this device, such as multimedia messaging (MMS),
browsing, e-mail application, instant messaging, presence enhanced contacts,
remote synchronization, and content downloading using the browser or MMS,
require network support for these technologies.
■ Shared memory
The following features in this device may share memory: gallery, contacts, text
messages, multimedia messages, and instant messages, e-mail, calendar, to-do
notes, Java
these features may reduce the memory available for the remaining features
sharing memory. For example, saving many Java applications may use all of the
available memory. Your device may display a message that the memory is full
when you try to use a shared memory feature. In this case, delete some of the
information or entries stored in the shared memory features before continuing.
Some of the features, such as text messages, may have a certain amount of
memory specially allotted to them in addition to the memory shared with other
features.
TM
games and ap plications, and note application. Use of one or more of
■ Enhancements
A few practical rules about accessories and enhancements
• Keep all accessories and enhancements out of the reach of small children.
• When you disconnect the power cord of any accessory or enhancement, grasp
and pull the plug, not the cord.
• Check regularly that enhancements installed in a vehicle are mounted and
are operating properly.
• Installation of any complex car enhancements must be made by qualified
personnel only.
8
D
RAFT
General information
General information
■ Overview of functions
Your phone provides many functions that are practical for daily use,
such as a text and multimedia messaging, a calendar, a clock, an alarm
clock, a radio, a music player, and a built-in camera. Your phone also
supports the following functions:
• Plug and play online service to get the configuration settings. See
Plug and play servicep. 15, and Configuration settings service p. 10.
• Payment and Ticketing by NFC. See Payment and ticketing p. 100.
• NFC to read and transmit information to service tags. See NFC p. 99.
• Push to talk. See Push to talk p. 82.
• A microSD memory card to extend the memory capacity of the
phone. See Insert a microSD card p. 13 and Memory card p. 70.
• Active standby. See Active standby p. 18.
• Audio messaging. See Nokia Xpress audio messaging p. 33.
• Instant messaging. See Instant messaging p. 37.
• E-mail application. See E-mail application p. 34.
• Enhanced voice dialing. See Enhanced voice dialing p. 22 and Voice
commands p. 57.
• Presence-enhanced contacts. See My presence p. 48.
• Java 2 Platform, Micro Edition (J2METM). See Applications p. 88.
D
RAFT
■ Access codes
Security code
The security code (5 to 10 digits) helps to protect your phone against
unauthorized use. The preset code is 12345. To change the code, and to
set the phone to request the code, see Security p. 67.
9
General information
PIN codes
The personal identification number (PIN) code and the universal
personal identification number (UPIN) code (4 to 8 digits) help to
protect your SIM card against unauthorized use. See Security p. 67.
The PIN2 code (4 to 8 digits) may be supplied with the SIM card and is
required for some functions.
The module PIN is required to access the information in the security
module. See Security module p. 97.
The signing PIN is required for the digital signature. See Digital
signature p. 98.
PUK codes
The personal unblocking key (PUK) code and the universal personal
unblocking key (UPUK) code (8 digits) is required to change a blocked
PIN code and UPIN code, respectively. The PUK2 code (8 digits) is
required to change a blocked PIN2 code. If the codes are not supplied
with the SIM card, contact your local service provider for the codes.
Barring password
The barring password (4 digits) is required when using the Call barring
service. See Security p. 67.
RAFT
Secure element passcode
Depending on the activation level, the secure element passcode
(4 digits) may be required to activate the secure element for payment
and ticketing using NFC. See Payment and ticketing p. 100.
■ Configuration settings service
To use some of the network services, such as mobile Internet services,
MMS, Nokia Xpress audio messaging, or remote Internet server
synchronization, your phone needs the correct configuration settings.
You may be able to receive the settings directly as a configuration
message. After receiving the settings you need to save them on your
10
D
General information
phone. The service provider may provide a PIN that is needed to save the
settings. For more information on availability, contact your network
operator, service provider, nearest authorized Nokia dealer, or visit the
support area on the Nokia Web site, www.nokia.com/support.
When you have received the settings as a configuration message, and
the settings are not automatically saved and activated, Configuration
settings received is displayed.
To save the settings, select Show > Save. If the phone requests Enter
settings' PIN:, enter the PIN code for the settings, and select OK. To
receive the PIN code, contact the service provider that supplies the
settings. If no settings are saved yet, these settings are saved and set as
default configuration settings. Otherwise, the phone asks Activate saved
configuration settings?.
To discard the received settings, select Exit or Show > Discard.
■ Download content
You may be able to download new content (for example, themes) to the
phone (network service). Select the download function (for example, in
the Gallery menu). To access the download function, see the respective
menu descriptions.
You may also be able to download updates of phone software (network
service). See Phone p. 64, Phone updates.
For the availability of different services, pricing, and tariffs, contact your
service provider.
D
Important: Use only services that you trust and that offer adequate
security and protection against harmful software.
RAFT
■ Software updates
Nokia may produce software updates that may offer new features, enhanced
functions, or improved performance. You may be able to request these updates
through the Nokia Software Updater PC application. To update the device
software, you need the Nokia Software Updater application and a compatible PC
with Microsoft Windows 2000 or XP operating system, broadband internet
access, and a compatible data cable to connect your device to the PC.
11
Get started
To get more information and to download the Nokia Software Updater
application, visit www.nokia.com/softwareupdate or your local Nokia web site.
If software updates over the air are supported by your network, you may also be
able to request updates through the device. See Phone p. 64, Phone updates.
Downloading software updates may involve the transmission of large amounts of
data through your service provider's network. Contact your service provider for
information about data transmission charges.
Make sure that the device battery has enough power, or connect the charger
before starting the update.
Important: Use only services that you trust and that offer adequate
security and protection against harmful software.
■ Nokia support
Check www.nokia.com/support or your local Nokia Web site for the
latest version of this guide, additional information, downloads, and
services related to your Nokia product.
On the Web site, you can get information on the use of Nokia products
and services. If you need to contact customer service, check the list of
local Nokia Care contact centers at www.nokia.com/customerservice.
For maintenance services, check your nearest Nokia service center at
www.nokia.com/repair.
RAFT
1. Get started
D
■ Install SIM card and battery
Always switch the device off and disconnect the charger before removing the
battery.
Keep all SIM cards out of the reach of small children.
For availability and information on using SIM card services, contact your SIM
card vendor. This may be the service provider, network operator, or other vendor.
This device is intended for use with BL-4C battery. Always use original
Nokia batteries. See Nokia battery authentication p. 104.
12
Get started
The SIM card and its contacts can easily be damaged by scratches or
bending, so be careful when handling, inserting, or removing the card.
To remove the back
cover of the phone,
press sightly (1) and
slide the cover (2).
Remove the battery as
shown (3).
Open the SIM card
holder (4). and insert
the SIM card properly
into the holder (5).
Close the SIM card
holder (6).
Replace the battery ( 7).
Slide the back cover
into its place (8, 9).
RAFT
■ Insert a microSD card
Keep all microSD memory cards out of the reach of small children.
1. Remove the back cover of the phone.
2. Insert the card into the microSD card
3. Close the back cover of the phone.
Use only compatible microSD cards with this device. Other memory cards, such as
Reduced Size MultiMedia cards, do not fit in the microSD card slot and are not
compatible with this device. Using an incompatible memory card may damage
D
slot with the golden contact surface
facing down, and press it until it locks
into place.
13
Get started
the memory card as well as the device, and data stored on the incompatible card
may be corrupted.
Use only microSD cards approved by Nokia for use with this device. Nokia utilizes
the approved industry standards for memory cards but not all other brands may
function correctly or be fully compatible with this device.
■ Remove the microSD card
Important: Do not remove the microSD card in the middle of an
operation when the card is being accessed. Removing the card in the
middle of an operation may damage the memory card as well as the
device, and data stored on the card may be corrupted.
You can remove or replace the microSD card during phone operation
without switching the phone off.
1. Make sure that no application is currently accessing the micro SD
memory card.
2. Remove the back cover of the phone.
3. Press the microSD card slightly in to release the locking.
4. Remove the microSD card from the slot.
■ Charge the battery
Check the model number of any charger before use with this device. This device is
intended for use when supplied with power from an AC-3 or AC-4 charger.
Warning: Use only batteries, chargers, and enhancements approved by
Nokia for use with this particular model. The use of any other types may
invalidate any approval or warranty, and may be dangerous.
For availability of approved enhancements, please check with your dealer. When
you disconnect the power cord of any enhancement, grasp and pull the plug, not
the cord.
1. Connect the charger to a wall socket.
2. Connect the lead from the charger to the socket
on the bottom of your phone.
If the battery is completely discharged, it may take a
few minutes before the charging indicator appears
on the display or before any calls can be made.
D
RAFT
14
Get started
The charging time depends on the charger used. Charging a BL-4C
battery with the AC-3 charger takes approximately 2 hours and
20 minutes while the phone is in the standby mode.
■ Open and close the phone
To open the phone press the fold
release button (1). The fold opens
automatically (2).
To close the phone turn the fold
manually in its closed position.
To switch off a tone that sounds
when you open and close the
phone, see Tones p. 54.
To read from or write to a service
tag the phone must be open.
■ Switch the phone on and off
Warning: Do not switch the phone on when wireless phone use is
prohibited or when it may cause interference or danger.
To switch the phone on or off, press and hold the power key. See Keys
and parts p. 17.
If the phone asks for a PIN or a UPIN code, enter the code (displayed as
****), and select OK.
RAFT
Set the time, time zone, and date
Enter the local time, select the time zone of your location in terms of the
time difference with respect to Greenwich Mean Time (GMT), and enter
the date. See Time and date p. 56.
Plug and play service
When you switch on your phone for the first time, and the phone is in
the standby mode, you are asked to get the configuration settings from
your service provider (network service). Confirm or decline the query.
D
15
Get started
See "Connect to serv. support," p. 66, and Configuration settings service
p. 10.
■ Antenna
Your device has an internal antenna.
Note: As with any other radio
transmitting device, do not touch
the antenna unnecessarily when the
device is switched on. Contact with
the antenna affects call quality and
may cause the device to operate at a
higher power level than otherwise
needed. Avoiding contact with the
antenna area when operating the
device optimizes the antenna
performance and the battery life.
■ Phone strap
Thread the strap through the eyelet of the
phone as shown in the picture and tighten
it.
RAFT
16
D
2. Your phone
■ Keys and parts
1 NFC detection area (grey)
2 Earpiece
3 Main display
4 Left and right selection keys
5 Middle selection key
6 Call key
7 Keypad
8 Infrared window
9 Fold release button
10 NaviTM key (scroll key)
11 End key
12 Loudspeaker
13 Phone strap eyelet
14 Pop-PortTM connector flap
15 Charger connector
16 Camera lens
17 Volume keys (Volume up = PTT key)
18 Mini display
19 Camera key
20 Power key
D
RAFT
Your phone
Connector flap
To connect enhancements, open the Pop-PortTM
connector flap.
17
Your phone
■ Standby mode
When the phone is ready for use, and you have not entered any
characters, the phone is in the standby mode.
Main display
1 Signal strength of the cellular network
2 Battery charge status
3 Indicators
4 Name of the network or the operator logo
5 Clock
6 Main screen
7 Function of the left selection key is Go to
or a shortcut to another function.
See Left selection keyp. 56.
8 Function of the middle selection key is Menu
9 Function of the right selection key is Names or
a shortcut to another function. See Right selection key p. 57.
Operator variants may have an operator-specific name to access an
operator-specific Web site.
Active standby
In the active standby mode there is a list of selected phone features and
information on the screen that you can directly access in the standby
mode. To switch on the mode, select Menu > Settings > Main display >
Standby mode settings >Active standby > My active standby. In the
standby mode, scroll up or down to activate the navigation in the list. To
start the feature, select Select; or to display the information, select
View. Left and right arrows at the beginning and end of a line indicate
that further information is available by scrolling left or right. To end the
active standby navigation mode, select Exit.
18
D
RAFT
Your phone
To organize and change the active standby mode, activate the
navigation mode, and select Options > Active standby > Options and
the following options:
Personalise — Assign or change phone features in the standby mode.
Organise — Move the position of features in the standby mode.
Enabling active standby — Select keys to activate the standby
navigation mode. To change the settings, see Standby mode settings
p. 55.
To switch off the active standby mode select Options > Ac tive
standby > Off; or select Menu > Settings > Main display > Standby
mode settings >Active standby > Off.
Shortcuts in the standby mode
• To access the list of dialed numbers, press the call key once. Scroll to
the number or name that you want; and to call the number, press the
call key.
• To open the web browser, press and hold 0.
• To call your voice mailbox, press and hold 1.
• Use the scroll key as a shortcut. See My shortcuts p. 56.
• Press the camera key to start the camera (still photo).
• In camera mode press the volume keys to zoom in or out.
• Press a volume key to mute the ringing tone of an incoming call
when the phone is closed.
• Press the power key to access the profiles menu on the main display.
D
RAFT
Indicators
You have unread messages in the Inbox folder.
You have unsent, canceled or failed messages in the Outbox
folder.
, Your phone is connected to the instant messaging service, and
the availability status is online or offline.
19
Your phone
The phone registered a missed call.
You received one or several instant messages, and you are
connected to the instant messaging service.
The keypad is locked.
The phone does not ring for an incoming call or text message.
The alarm clock is set to On.
The countdown timer is running.
The stopwatch is running in the background.
, The phone is registered to the GPRS or EGPRS network.
, A GPRS or EGPRS connection is established.
, The GPRS or EGPRS connection is suspended (on hold), for
example, if there is an incoming or outgoing call during an
EGPRS dial-up connection.
A Bluetooth connection is active.
, Push to talk connection is active or suspended. See Push to talk
p. 82.
If you have two phone lines, the second phone line is selected.
All incoming calls are diverted to another number.
Calls are limited to a closed user group.
D
The timed profile is selected.
, , , or
A headset, hands-free, loopset, or music stand enhancement is
connected to the phone.
The NFC detection is activated or deactivated.
The secure element is always active, deactivated, or passcode
protected.
RAFT
20
Call functions
■ Keypad lock (keyguard)
To prevent the keys from being accidentally pressed, select Menu, and
press * within 3.5 seconds to lock the keypad.
To unlock the keypad, select Unlock, and press * within 1.5 seconds. If
the Security keyguard is set On, enter the security code if requested.
To answer a call when the keyguard is on, press the call key. When you
end or reject the call, the keypad automatically locks.
For Security keyguard, see Phone p. 64.
When the keyguard is on, calls still may be possible to the official emergency
number programmed into your device.
■ Functions without a SIM card
Several functions of your phone may be used without installing a SIM
card (for example, the data transfer with a compatible PC or another
compatible device). Also reading and writing of service tags or payment
and ticketing with NFC may be possible without installing a SIM card.
Note that when you use the phone without a SIM card, some functions
appear dimmed in the menus and cannot be used. Synchronizing with a
remote Internet server is not possible without a SIM card.
For an emergency call, some networks may require that a valid SIM card is
properly inserted in the device.
RAFT
3. Call functions
■ Make a call
1. Enter the phone number, including the area code.
2. To call the number, press the call key.
D
For international calls, press * twice for the international prefix (the
+ character replaces the international access code), enter the
country code, the area code without the leading 0, if necessary, and
the phone number.
21
Call functions
3. To end the call or to cancel the call attempt, press the end key, or
close the phone.
To search for a name or phone number that you have saved in Contacts,
see Search for a contact p. 46. Press the call key to call the number.
To access the list of dialled numbers, press the call key once in the
standby mode. To call the number, select a number or name, and press
the call key.
Speed dialing
Assign a phone number to one of the speed-dialing keys, 2 to 9. See
Speed dials p. 52. Call the number in either of the following ways:
• Press a speed-dialing key, then the call key.
•If Speed dialling is set to On, press and hold a speed-dialing key until
the call begins. See Speed dialli ng in Call p. 63.
Enhanced voice dialing
You can make a phone call by saying the name that is saved in the
contact list of the phone. A voice command is added automatically to all
entries in the contact list of the phone.
If an application is sending or receiving data using a packet data
connection, end the application before you use voice dialing.
Voice commands are language-dependent. To set the language, see
Voice playback language in Phone p. 64.
Note: Using voice tags may be difficult in a noisy environment or
D
during an emergency, so you should not rely solely upon voice dialing in
all circumstances.
1. In the standby mode, press and hold the right selection key or press
and hold the volume down key. A short tone is played, and Speak now
is displayed.
If you are using a compatible headset with the headset key, press and
hold the headset key to start the voice dialing.
2. Say the voice command clearly. If the voice recognition was
successful, a list with matches is shown. The phone plays the voice
RAFT
22
Call functions
command of the match on the top of the list. After about
1.5 seconds, the phone dials the number; or if the result is not the
correct one, scroll to another entry, and select to dial the entry.
Using voice commands to carry out a selected phone function is
similar to voice dialing. See Voice commands in My shortcuts p. 56.
Make a call using NFC
Touch a service tag containing a call request with the NFC detection
area. See NFC detection p. 100. The phone displays the callback number.
Select Call to call the number, or Exit to discard. To transmit a call
request to a service tag, see Transmit to service tags p. 101.
■ Answer or reject a call
To answer an incoming call, press the call key, or open the phone. To end
the call, press the end key or close the phone.
To reject an incoming call if the phone is open, press the end key. To
reject an incoming call when the phone is closed, press and hold a
volume key.
To mute the ringing tone, press a volume key when the phone is closed,
or select Silence when the phone is open.
Tip: If the Divert if busy function is activated to divert the calls
(for example, to your voice mailbox), rejecting an incoming call
also diverts the call. See Call p. 63.
If a compatible headset supplied with the headset key is connected to
the phone, to answer and end a call, press the headset key.
D
RAFT
Call waiting
To answer the waiting call during an active call, press the call key. The
first call is put on hold. To end the active call, press the end key.
To activate the Call waiting function, see Call p. 63.
23
Write text
■ Options during a call
Many of the options that you can use during a call are network services.
For availability, contact your service provider.
During a call, select Options and from the following options:
Call options are Mute or Unmute, Contacts, Menu, Lock keypad, Record,
Loudspeaker or Handset.
Network services options are Answer or Reject, Hold or Unhold, New
call, Add to conference, End call, End all calls, and the following:
Send DTMF — to send tone strings
Swap — to switch between the active call and the call on hold
Transfer — to connect a call on hold to an active call and disconnect
yourself
Conference — to make a conference call that allows up to five persons to
take part in a conference call
Private call —to discuss privately in a conference call
Warning: Do not hold the device near your ear when the loudspeaker
is in use, because the volume may be extremely loud.
4. Write text
You can enter text (for example, when writing messages) using
traditional or predictive text input. When you write text, text input
indicators appear at the top of the display. indicates traditional text
input. indicates predictive text input. Predictive text input allows
you to write text quickly using the phone keypad and a built-in
dictionary. You can enter a letter with a single keypress. indicates
predictive text input with Word suggestions. The phone predicts and
completes the word before you enter all the characters.
the character case. To change the character case, press #.
24
D
, , or appears next to the text input indicator, indicating
RAFT
Write text
indicates number mode. To change from the letter to number mode,
press and hold #, and select Number mode.
To set the writing language while writing text, select Options > Writing
language.
■ Predictive text input
To set predictive text input on, select Options > Prediction on.
Tip: To quickly set predictive text input on or off when writing
text, press # twice, or select and hold Options.
1. Start writing a word using the 2 to 9 keys. Press each key only once
for one letter. The entered letters are displayed underlined.
To insert a special character, press and hold *, or select Options >
Insert symbol. Scroll to a character, and select Use.
To write compounds words, enter the first part of the word; to
confirm it, press the scroll key right. Write the next part of the word
and confirm the word.
To enter a full stop, press 1.
2. When you finish writing the word and it is correct, to confirm it,
press 0 to add space.
If the word is not correct, press * repeatedly, or select Options >
Matches. When the word that you want appears, select the word and
press the navigation key.
If the ? character is displayed after the word, the word you intended
to write is not in the dictionary. To add the word to the dictionary,
D
select Spell. Complete the word (traditional text input is used), and
select Save.
RAFT
■ Traditional text input
To set traditional text input on, select Options > Prediction off.
Press a number key, 1 to 9, repeatedly until the desired character
appears. Not all characters available under a number key are printed on
25
Navigate the menus
the key. The characters available depend on the selected writing
language.
If the next letter you want is located on the same key as the present one,
wait until the cursor appears, or briefly press any of the navigation keys
and enter the letter.
The most common punctuation marks and special characters are
available under the 1 key. For more characters, press *.
5. Navigate the menus
The phone offers you an extensive range of functions, which are
grouped into menus.
1. To access the menu, select Menu.
To change the menu view, select Options > Main menu view > List,
Grid, Grid with labels, or Tab.
To rearrange the menu, scroll to the menu you want to move, and
select Options > Organise > Move. Scroll to where you want to
move the menu, and select OK. To save the change, select Done >
Yes.
2. Scroll through the menu, and select an option (for example,
Settings).
3. If the selected menu contains further submenus, select the one that
you want (for example, Call).
4. If the selected menu contains further submenus, repeat step 3.
5. Select the setting of your choice.
6. To return to the previous menu level, select Back. To exit the menu,
select Exit.
D
RAFT
26
Messaging
6. Messaging
You can read, write, send, and save text, multimedia,
e-mail, audio, and flash messages and postcards. All messages are
organized into folders.
■ Text messages (SMS)
With the short message service (SMS) you can send and receive text
messages, and receive messages that can contain pictures (network
service).
Before you can send any text or SMS e-mail message, you must save
your message center number. See Message settings p. 43.
To check SMS e-mail service availability and to subscribe to the service,
contact your service provider. To save an e-mail address in Contacts, see
Save details p. 47.
Your device supports the sending of text messages beyond the character limit for
a single message. Longer messages will be sent as a series of two or more
messages. Your service provider may charge accordingly. Characters that use
accents or other marks, and characters from some language options like Chinese,
take up more space limiting the number of characters that can be sent in a single
message.
The message length indicator at the top of the display shows the total
number of characters left and the number of messages needed for
sending. For example, 673/2 means that there are 673 characters left
and that the message will be sent as a series of two messages.
You may also read a text message from a service tag or write a text
message to a service tag. See NFC p. 99.
D
RAFT
Write and send a SMS message
1. Select Menu > Messaging > Create message > Text message.
2. Enter the recipient’s phone number or e-mail address in the To: field.
To retrieve a phone number or e-mail address from Contacts, select
Add > Contact. To send the message to multiple recipients, add the
27
Messaging
desired contacts one by one. To send the message to persons in a
group, select Contact group and the desired group. To retrieve the
contacts to which you recently sent messages, select Add > Recently
used. To retrieve contacts from previously incoming calls, select
Add > Open Log.
3. For a SMS e-mail, enter a subject in the Subject: field.
4. Write your message in the Message: field. See Write text p. 24. To
insert a template into the message, select Options > Use template.
To see how the message will look to the recipient, select Options >
Preview.
5. To send the message, select Send. See Message sending p. 30.
To write the message to a service tag, select Options > Transmit to
tag. Touch the service tag with the NFC detection area to transfer
the message.
Read and reply to an SMS message
When you have received a message, 1 message received or the number
of new messages with messages received are shown.
1. To view a new message, select Show. To view it later, select Exit.
To read the message later, select Menu > Messaging > Inbox. If more
than one message is received, select the message you want to read.
is shown if you have unread messages in Inbox.
2. To view the list of available options while reading a message, select
Options.
3. To reply to a message, select Reply > Text message, Multimedia,
Flash message, or Audio message.
To send a text message to an e-mail address, enter the e-mail
address in the To: field.
Scroll down, and write your message in the Message: field. See Write
text p. 24.
If you want to change the message type for your reply message,
select Options > Change message type.
D
RAFT
28
Messaging
4. To send the message, select Send. See Message sending p. 30.
To write the message to a service tag, select Options > Transmit to
tag. Touch the service tag with the NFC detection area to transfer
the message.
■ SIM messages
SIM messages are text messages that are saved to your SIM card. You
can copy or move those messages to the phone memory, but not vice
versa. Received messages are saved to the phone memory.
To read SIM messages, select Menu > Messaging > Options > SIM
messages.
■ Multimedia messages (MMS)
Note: Only devices that have compatible features can receive and
display multimedia messages. The appearance of a message may vary
depending on the receiving device.
To check availability and to subscribe to the multimedia messaging
network service, contact your service provider. See Multimedia
messages p. 44.
A multimedia message can contain text, sound, images, video clips, a
business card, and a calendar note. If the message is too large, the
phone may not be able to receive it. Some networks allow text messages
that include an Internet address where you can view the multimedia
message.
You cannot receive multimedia messages during a call or an active
browsing session over GSM data. Because delivery of multimedia
messages can fail for various reasons, do not rely solely upon them for
essential communications.
D
RAFT
Write and send a MMS message
The wireless network may limit the size of MMS messages. If the inserted image
exceeds this limit, the device may make it smaller so that it can be sent by MMS.
1. Select Menu > Messaging > Create message > Multimedia.
2. Enter your message.
29
Messaging
Your phone supports multimedia messages that contain several
pages (slides). A message can contain a calendar note and a business
card as attachments. A slide can contain text, one image, and one
sound clip; or text and a video clip. To insert a slide in the message,
select New; or select Options > Insert > Slide.
To insert a file in the message, select Insert; or select Options >
Insert.
3. To view the message before sending it, select Options > Preview.
4. To send the message, select Send. See Message sending p. 30.
5. Enter the recipient’s phone number in the To: field. To retrieve a
phone number from Contacts, select Add > Contact. To send the
message to multiple recipients, add the desired contacts one by one.
To send the message to persons in a group, select Contact group and
the desired group. To retrieve the contacts to which you recently sent
messages, select Add > Recently used.
Message sending
Copyright protections may prevent some images, music (including ringing tones),
and other content from being copied, modified, transferred or forwarded.
When you finish writing your message, to send the message, select
Send. The phone saves the message in the Outbox folder, and the
sending starts. If you select Save sent messages > Yes, the sent message
is saved in the Sent items folder. See General settings p. 43.
Note: When the phone is sending the message, the animated is
shown. This is an indication that the message has been sent by your
D
device to the message center number programmed into your device.
This is not an indication that the message has been received at the
intended destination. For more details about messaging services, check
with your service provider.
It takes more time to send a multimedia message than to send a text
message. While the message is being sent, you can use other functions
on the phone. If an interruption occurs while the message is being sent,
the phone tries to resend the message a few times. If these attempts fail,
the message remains in the Outbox folder. You can try to resend it later.
RAFT
30
Loading...