Microsoft RM-167, RM-166 User Manual
Nokia 6070 User Guide
FCC-Draft
Issue 1
DECLARATION OF CONFORMITY
Hereby, NOKIA CORPORATION declares that this RM-166 and RM-XXX product is in
compliance with the essential requirements and other relevant provisions of Directive 1999/
5/EC. A copy of the Declaration of Co nformity can be found at
http://www.nokia.com/phones/declaration_of_conformity/.
0434
The crossed-out wheeled bin means that within the European Union the product
must be taken to separate collection at the product end-of life. This applies to your
device but also to any enhancements marked with this symbol. Do not dispose of
these products as unsorted municipal waste.
Copyright © 2006 Nokia. All rights reserved.
Reproduction, transfer, distribution or storage of part or all of the contents in this document
in any form without the prior written permission of Nokia is prohibited.
Nokia, Nokia Connecting People, Xpress-on, and Pop-Port are trademarks or registered
trademarks of Nokia Corporation. Other product and company names mentioned herein may
be trademarks or tradenames of their respective owners.
Nokia tune is a sound mark of Nokia Corporation.
US Patent No 5 818437 and other pending patents. T9 text input software Copyright (C)
1997-2005. Tegic Comm unications, Inc. All rights reserved.
Includes RSA BSAFE cryptographic or security protocol software from RSA Security.
Java is a trademark of Sun Microsystems, Inc.
This product is licensed under the MPEG-4 Visual Patent Portfolio License (i) for personal and
noncommer cial use in connection with information wh ich has been encoded in complianc e
with the MPEG-4 Visual Standard by a consumer engaged in a personal and noncommercial
activity and (ii) for use in connection with MPEG -4 video provided by a licensed video
provider. No license is granted or shall be implied for any other use. Additional information,
including that related to prom otional, internal, and commercial uses, may be obtained from
MPEG LA, LLC. See <http://www.mpegla.com>.
Nokia operates a policy of continuous development. Nokia reserves the right to make
changes and improvements to any of the products described in this document without prior
notice.
This Nokia device complies with Directive 2002/95/EC on the restriction of the use of certain
hazardous substances in electrical and electronic equipment.
Under no circumstances shall Nokia be resp onsible for any loss of data or income or any
special, incidental, consequential or indirect damages howsoever caused.
The contents of th is document are pr ovided "as is". Ex cept as required by applicable law, no
warranties of any kind, either express or implied, including, but not limited to, the implied
warranties of merchantability a nd fitness for a particu lar purpose, are made i n relation to the
accuracy, reliability or contents of this document. Nokia reserves the right to revise this
document or withdraw it at any time without prior notice.
The availability of particular products may vary by region. Please check with the Nokia dealer
nearest to you.
This device may contain commodities, technology or software subject to export laws and
regulations from the US and oth er countries. Diversion contrary to law is prohibited.
FCC/INDUSTRY CANADA NOTICE
Your device may caus e TV or radio interference (for example, when us ing a telephone in close
proximity to receiving equipment). The FCC or Industry Canada can require you to stop using
your telep hone if such interference cannot be elimin ated. If you require assistance , contact
your local service facility. This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may
cause undesired operation. Any changes or modifications not expressly approved by Nokia
could void the u ser's authority to operate this equipment.
9248899/FCC Draft Issue1
Contents
For your safety.......................... 6
General information................. 9
Overview of functions........................... 9
Access codes............................................ 9
Configuration settings service ........ 10
Download content and applications 11
Nokia support and contact information
11
1. Get started ......................... 12
Install the SIM card and battery .... 12
Charge the battery.............................. 13
Switch the phone on and off........... 14
Antenna ................................................. 14
Wrist strap ............................................ 15
2. Your phone......................... 16
Keys and parts...................................... 16
Standby mode ...................................... 17
Keypad lock (keyguard) ..................... 19
3. Call functions..................... 20
Make a call ........................................... 20
Answer or reject a call....................... 20
Options during a call.......................... 21
4. Write text........................... 22
Settings.................................................. 22
Predictive text input .......................... 22
Traditional text input......................... 23
5. Navigate the menus .......... 24
6. Messages ............................ 25
Text messages (SMS).......................... 25
Multimedia messages (MMS) .......... 27
Memory full .......................................... 29
Folders .................................................... 30
Postcards ............................................... 30
Flash messages .................................... 31
Nokia Xpress audio messaging........ 31
Instant messaging (IM) ..................... 32
E-mail application .............................. 37
Voice messages.................................... 39
Info messages ...................................... 39
Service commands .............................. 39
Delete messages .................................. 39
Message settings................................. 39
Message counter ................................. 42
7. Contacts.............................. 43
Search for a contact .......................... 43
Save names and phone numbers.... 43
Save numbers, items, or an image . 43
Copy contacts ...................................... 44
Edit contact details ............................ 44
Delete contacts or contact details. 44
Business cards...................................... 45
My presence ......................................... 45
Subscribed names ............................... 46
Settings.................................................. 47
Groups.................................................... 47
Voice dialing......................................... 48
Speed dials............................................ 49
Info, service, and my numbers ........ 49
8. Call register ........................ 50
Recent calls lists.................................. 50
Counters and timers........................... 50
9. Settings ............................. 51
Profiles ................................................... 51
Themes ................................................... 51
Tones....................................................... 51
My shortcuts ........................................ 52
Display.................................................... 52
Time and date ...................................... 53
Call .......................................................... 53
4
Phone ...................................................... 54
Connectivity .......................................... 55
Enhancements ...................................... 57
Configuration........................................ 57
Security .................................................. 58
Restore factory settings..................... 59
10.Operator menu.................. 60
11.Gallery ............................... 60
12.Media ................................ 61
Camera ................................................... 61
Radio ....................................................... 61
Recorder ................................................. 63
13.Organizer........................... 64
Alarm clock............................................ 64
Calendar ................................................. 64
To-do list................................................ 65
Notes....................................................... 66
Synchronization ................................... 66
Calculator .............................................. 67
Stopwatch ............................................. 68
Countdown timer ................................ 69
14.Applications...................... 70
Games ..................................................... 70
Collection............................................... 70
15.Push to talk....................... 72
Push to talk menu ............................... 72
Connect to and disconnect PTT....... 73
Make and receive a PTT call ............. 73
Callback requests................................. 75
Add a one-to-one contact ................ 77
Create and set up channels .............. 77
PTT settings ........................................... 79
16.Web.................................... 80
Set up browsing ................................... 80
Connect to a service........................... 80
Browse pages........................................ 81
Appearance settings ........................... 82
Cookies ................................................... 83
Scripts over secure connection ....... 83
Bookmarks ............................................. 83
Download files...................................... 84
Service inbox ........................................ 84
Cache memory...................................... 85
Browser security .................................. 85
Positioning information ..................... 87
17.SIM services....................... 89
18.PC connectivity ................. 90
Nokia PC Suite...................................... 90
Packet data, HSCSD, and CSD.......... 90
Data communication applications . 90
19.Battery information.......... 91
Charging and discharging ................. 91
Nokia battery authentication
guidelines............................................... 91
20.Technical Information ...... 94
Care and maintenance ........... 95
Additional safety information 96
APPENDIX ............................ 100
A message from the CTIA.................100
Message from the FDA......................103
Index..................................... 109
5
For your safety
For your safety
Read these simple guidelines. Not following them may be dangerous or illegal.
Read the complete user guide for further information.
SWITCH ON SAFELY
Do not switch the phone on when wireless phone use is prohibited or
when it may cause interference or danger.
ROAD SAFETY COMES FIRST
Obey all local laws. Always keep your hands free to operate the
vehicle while driving. Your first consideration while driving should be
road safety.
INTERFERENCE
All wireless phones may be susceptible to interference, which could
affect performance.
SWITCH OFF IN HOSPITALS
Follow any restrictions. Switch the phone off near medical
equipment.
SWITCH OFF IN AIRCRAFT
Follow any restrictions. Wireless devices can cause interference in
aircraft.
SWITCH OFF WHEN REFUELING
Do not use the phone at a refueling point. Do not use near fuel or
chemicals.
SWITCH OFF NEAR BLASTING
Follow any restrictions. Do not use the phone where blasting is in
progress.
USE SENS IBLY
Use only in the normal position as explained in the product
documentation. Do not touch the antenna unnecessarily.
QUALIFIED SERVICE
Only qualified personnel may install or repair this product.
ENHANCEMENTS AND BATTERIES
Use only approved enhancements and batteries. Do not connect
incompatible products.
6
For your safety
WATER-RESISTANCE
Your phone is not water-resistant. Keep it dry.
BACK-UP COPIES
Remember to make back-up copies or keep a written record of all
important information stored in your phone.
CONNECTING TO OTHER DEVICES
When connecting to any other device, read its user guide for detailed
safety instructions. Do not connect incompatible products.
EMERGENCY CALLS
Ensure the phone is switched on and in service. Press the end key as
many times as needed to clear the display and return to the start
screen. Enter the emergency number, then press the call key. Give
your location. Do not end the call until given permission to do so.
■ About your device
The wireless device described in this guide is approved for use on the EGSM 900
and GSM 1800 and 1900 networks. Contact your service provider for more
information about networks.
When using the features in this device, obey all laws and respect the privacy and
legitimate rights of others.
Warning: To use any features in this device, other than the alarm clock,
the device must be switched on. Do not switch the device on when
wireless device use may cause interference or danger.
■ Network services
To use the phone you must have service from a wireless service provider. Many of
the features in this device depend on features in the wireless network to
function. These network services may not be available on all networks or you may
have to make specific arrangements with your service provider before you can
utilize network services. Your service provider may need to give you additional
instructions for their use and explain what charges will apply. Some networks
may have limitations that affect how you can use network services. For instance,
some networks may not support all language-dependent characters and services.
Your service provider may have requested that certain features be disabled or not
activated in your device. If so, they will not appear on your device menu. Your
device may also have been specially configured for your network provider. This
7
For your safety
configuration may include changes in menu names, menu order, and icons.
Contact your service provider for more information.
This device supports WAP 2.0 protocols (HTTP and SSL) that run on TCP/IP
protocols. Some features of this device, such as text messages, multimedia
messages, audio messages, instant messaging service, e-mail, presence enhanced
contacts, mobile Internet services, content and application download, and
synchronization with a remote Internet server, require network support for these
technologies.
■ Shared memory
The phone has two memories. The following features may share the first memory:
contacts, text messages, multimedia messages (but no attachments), audio
messages, instant messaging, groups, voice commands, calendar, and to-do
notes. The second shared memory is used by files stored in Gallery, attachments
of multimedia messages, e-mail, and Java
these features may reduce the memory available for the remaining features
sharing memory. For example, saving many Java applications may use all of the
available memory. Your device may display a message that the memory is full
when you try to use a shared memory feature. In this case, delete some of the
information or entries stored in the shared memory features before continuing.
Some of the features, such as text messages, may have a certain amount of
memory specially allotted to them in addition to the memory shared with other
features.
TM
applications. Use of one or more of
■ Enhancements
A few practical rules about accessories and enhancements:
• Keep all accessories and enhancements out of the reach of small children.
• When you disconnect the power cord of any accessory or enhancement, grasp
and pull the plug, not the cord.
• Check regularly that enhancements installed in a vehicle are mounted and
are operating properly.
• Installation of any complex car enhancements must be made by qualified
personnel only.
8
General information
General information
■ Overview of functions
Your phone provides many functions that are practical for daily use,
such as a calendar, a clock, an alarm clock, a radio, and a built-in
camera. Your phone also supports the following functions:
• Enhanced data rates for GSM evolution (EDGE). See “Packet data
(EGPRS),” p. 56.
• Extensible hypertext markup language (XHTML). See “Web,” p. 80.
• Audio messaging. See “Nokia Xpress audio messaging,” p. 31.
• Instant messaging. See “Instant messaging (IM),” p. 32.
• E-mail application. See “E-mail application,” p. 37.
• Push to talk. See “Push to talk,” p. 72.
• Presence-enhanced contacts. See “My presence,” p. 45.
TM
• Java 2 Platform, Micro Edition (J2ME
• Synchronization and file transfer with PC Suite. See “Nokia PC Suite,”
p. 90.
■ Access codes
). See “Applications,” p. 70.
Security code
The security code (5 to 10 digits) helps to protect your phone against
unauthorized use. The preset code is 12345. To change the code, and to
set the phone to request the code, see “Security,” p. 58.
PIN codes
The personal identification number (PIN) code and the universal
personal identification number (UPIN) code (4 to 8 digits) help to
protect your SIM card against unauthorized use. See “Security,” p. 58.
The PIN2 code (4 to 8 digits) may be supplied with the SIM card and is
required for some functions.
9
General information
The module PIN is required to access the information in the security
module. See “Security module,” p. 85.
The signing PIN is required for the digital signature. See “Digital
signature,” p. 87.
PUK codes
The personal unblocking key (PUK) code and the universal personal
unblocking key (UPUK) code (8 digits) are required to change a blocked
PIN code and UPIN code, respectively. The PUK2 code (8 digits) is
required to change a blocked PIN2 code. If the codes are not supplied
with the SIM card, contact your local service provider for the codes.
Barring password
The barring password (4 digits) is required when using the Call barring
service. See “Security,” p. 58.
■ Configuration settings service
To use some of the network services, such as mobile Internet services,
MMS, Nokia Xpress audio messaging, or remote Internet server
synchronization, your phone needs the correct configuration settings.
You may be able to receive the settings directly as a configuration
message. After receiving the settings, you need to save them on your
phone. The service provider may provide a PIN that is needed to save the
settings. For more information on availability, contact your network
operator, service provider, nearest authorized Nokia dealer, or visit the
support area on the Nokia Web site at www.nokia.com/support.
When you have received a configuration message Configuration sett.
received is displayed.
To save the settings, select Show > Save. If the phone requests Enter
settings' PIN:, enter the PIN code for the settings, and select OK. To
receive the PIN code, contact the service provider that supplies the
settings. If no settings are saved yet, these settings are saved and set as
default configuration settings. Otherwise, the phone asks Activa te saved
configuration settings?.
10
General information
To discard the received settings, select Exit or Show > Discard.
To edit the settings, see “Configuration,” p. 57.
■ Download content and applications
You may be able to download new content (for example, themes) to the
phone (network service). Select the download function (for example, in
the Gallery menu). To access the download function, see the respective
menu descriptions. For the availability of different services, pricing, and
tariffs, contact your service provider.
Important: Use only services that you trust and that offer adequate
security and protection against harmful software.
■ Nokia support and contact information
Check www.nokia.com/support or your local Nokia Web site for the
latest version of this guide, additional information, downloads, and
services related to your Nokia product.
On the Web site, you can get information on the use of Nokia products
and services. If you need to contact customer service, check the list of
local Nokia contact centers at www.nokia.com/customerservice.
For maintenance services, check your nearest Nokia service center at
www.nokia.com/repair.
11
Get started
1. Get started
■ Install the SIM card and battery
Always switch the device off and disconnect the charger before removing the
battery.
Keep all SIM cards out of the reach of small children.
For availability and information on using SIM card services, contact your SIM
card vendor. This may be the service provider, network operator, or other vendor.
This device is intended for use with the BL-5B battery.
The SIM card and its contacts can easily be damaged by scratches or
bending, so be careful when handling, inserting, or removing the card.
To remove the back cover of the phone,
press the release button (1), and lift the
back cover (2).
Ensure that the gold-colored contact area
on the SIM card is facing downwards, and
insert the SIM card into the SIM card
holder until it snaps into position (3).
Insert the battery (4). Observe the battery
contacts. Always use original Nokia
batteries. See “Nokia battery
authentication guidelines,” p. 91.
Align the top of the back cover with the
top of the phone (5), and press the bottom
of the back cover to lock it (6).
12
Get started
To remove the battery, lift the lower end of
the battery out of the compartment (7).
To remove the SIM card, press the SIM
card release (8), and slide the SIM card
towards the top of the phone (9).
■ Charge the battery
Warning: Use only batteries, chargers, and enhancements approved by
Nokia for use with this particular model. The use of any other types may
invalidate any approval or warranty, and may be dangerous.
Check the model number of any charger before use with this device. This device is
intended for use when supplied with power from an AC-3, AC-4, and DC-4
charger, and from an AC-1, ACP-7, ACP-12, and LCH-12 charger when used with
the CA-44 charger adapter.
For availability of approved enhancements, please check with your dealer.
When you disconnect the power cord of any enhancement, grasp and pull the
plug, not the cord.
1. Connect the charger to a wall socket.
2. Connect the lead from the charger to
the socket on the bottom of your phone.
If the battery is completely discharged, it
may take a few minutes before the
charging indicator appears on the display or before any calls can be
made.
The charging time depends on the charger and the battery used. For
example, charging a BL-5B battery with the AC-3 charger takes about
1 hour and 10 minutes while the phone is in the standby mode.
13
Get started
■ Switch the phone on and off
Warning: Do not sw itch t he phone on when wireless
phone use is prohibited or when it may cause
interference or danger.
To switch the phone on, press and hold the power key.
If the phone asks for a PIN or a UPIN code, enter the code
(displayed as ****), and select OK.
To switch the phone off, press and hold the power key.
Set the time, time zone, and date
Enter the local time, select the time zone of your location in terms of the
time difference with respect to Greenwich Mean Time (GMT), and enter
the date. See “Time and date,” p. 53.
Plug and play service
When you switch on your phone for the first time, and the phone is in
the standby mode, you are asked to get the configuration settings from
your service provider (network service). Confirm or decline the query.
See "Connect to service provider support ," p. 58 and “Configuration
settings service,” p. 10.
■ Antenna
Your device has an internal antenna.
Note: As with any other radio
transmitting device, do not touch the
antenna unnecessarily when the device
is switched on. Contact with the antenna
affects call quality and may cause the
device to operate at a higher power level
than otherwise needed. Avoiding contact
with the antenna area when operating
the device optimizes the antenna
performance and the battery life.
14
■ Wrist strap
To attach the wrist strap to the bottom of the phone,
open the back cover. Thread the lace around the hook
(1) as shown in the picture. Hold the lace in its
position and close the back cover (2).
Get started
15
Your phone
2. Your phone
■ Keys and parts
• Power key (1)
• Earpiece (2)
• Loudspeaker (3)
• Display (4)
• Volume up and
push to talk (PTT) key (5)
• Volume down and
voice command key (6)
• Infrared (IR) port (7)
• Middle selection key (8)
• 4-way navigation key (9)
• Left selection key (10)
• Right selection key (11)
• Call key (12)
• End key (13)
• Keypad, may vary by region (14)
• Charger connector (15)
• Microphone (16)
• Pop-PortTM connector (17)
• Camera lens (18)
Warning: The navigation key (9) in this device may contain
nickel. The navigation key (9) is not designed for prolonged
contact with the skin. Continuous exposure to nickel on the skin
may lead to nickel allergy.
16
Your phone
■ Standby mode
When the phone is ready for use, and you have not entered any
characters, the phone is in the standby mode.
1 Name of the network or operator logo
2 Signal strength of the cellular network
3 Battery charge level
4 Left selection key (Go to)
5 Middle selection key (Menu)
6 Right selection key (Names)
The right selection key may be another
shortcut to a function that you selected. See
“My shortcuts,” p. 52. Operator variants may have an operator-specific
name to access an operator-specific Web site.
Personal shortcut list
The left selection key is Go to. To view the functions in the personal
shortcut list, select Go to. To activate a function, select it.
To view a list with available functions, select Go to > Options > Select
options. To add a function to the shortcut list, select Mark. To remove a
function from the list, select Unmark.
To rearrange the functions on your personal shortcut list, select Go to >
Options > Organise. Select the desired function, Move, and the place
where you want to move the function.
Shortcuts in standby mode
• To access the list of dialed numbers, press the call key once. Scroll to
a number or name; to call the number, press the call key.
• To open the Web browser, press and hold 0.
• To call your voice mailbox, press and hold 1.
• Use the navigation key as a shortcut. See “My shortcuts,” p. 52.
17
Your phone
Power saving
A digital clock view overwrites the display when no
function of the phone has been used for a certain
period of time. To activate the power saver, see
Powe r sav er in “Display,” p. 52. To deactivate the
screen saver, press any key.
Indicators
You received one or several text or picture messages. See “Read
and reply to an SMS message,” p. 26.
You received one or several multimedia messages. See “Read
and reply to an MMS message,” p. 29.
Different icons may appear for e-mail and voice messages.
The phone registered a missed call. See “Call register,” p. 50.
The keypad is locked. See “Keypad lock (keyguard),” p. 19.
The phone does not ring for an incoming call or text message
when Incoming call alert and Message alert tone are set to Off.
See “Tones,” p. 51.
The alarm clock is set to On. See “Alarm clock,” p. 64.
If the packet data connection mode Always online is selected,
the packet data service is available. See “Packet data (EGPRS),”
p. 56.
A packet data connection is established. See “Packet data
(EGPRS),” p. 56 and “Browse pages,” p. 81.
The packet data connection is suspended (on hold), for example,
if there is an incoming or outgoing call during a packet data
dial-up connection.
When the infrared connection is activated, the indicator is
shown continuously.
Push to talk connection is active or suspended. See “Push to
talk,” p. 72.
18
Your phone
■ Keypad lock (keyguard)
To prevent the keys from being accidentally pressed, select Menu, and
press * within 3.5 seconds to lock the keypad.
To unlock the keypad, select Unlock, and press * within 1.5 seconds. If
the Security keyguard is set On, enter the security code if requested.
To answer a call when the keyguard is on, press the call key. When you
end or reject the call, the keypad automatically locks.
For Automatic keyguard and Security keyguard, see “Phone,” p. 54.
When the keyguard is on, calls still may be possible to the official emergency
number programmed into your device.
19
Call functions
3. Call functions
■ Make a call
1. Enter the phone number, including the area code.
For international calls, press * twice for the international prefix (the
+ character replaces the international access code), then enter the
country code, the area code without the leading 0, if necessary, and
the phone number.
2. To call the number, press the call key.
3. To end the call or to cancel the call attempt, press the end key.
To make a call using names, search for a name or phone number in
Contacts. See “Search for a contact,” p. 43.
Press the call key to call the number.
To access the list of up to 20 dialed numbers, press the call key once in
the standby mode. To call the number, select a number or name, and
press the call key.
Speed dialing
Assign a phone number to one of the speed-dialing keys, 2 to 9. See
“Speed dials,” p. 49. Call the number in either of the following ways:
• Press a speed-dialing key, then press the call key.
•If Speed dialling is set to On, press and hold a speed-dialing key until
the call begins. See Speed dialli ng in “Call,” p. 53.
■ Answer or reject a call
To answer an incoming call, press the call key. To end the call, press the
end key.
To reject an incoming call, press the end key.
To mute the ringing tone, select Silence.
20
Call functions
Tip: If the Divert if busy function is activated to divert the calls
(for example, to your voice mailbox), rejecting an incoming call
also diverts the call. See “Call,” p. 53.
If a compatible headset with a headset key is connected to the phone, to
answer and end a call, press the headset key.
Call waiting
To answer the waiting call during an active call, press the call key. The
first call is put on hold. To end the active call, press the end key.
To activate the Call waiting function, see “Call,” p. 53.
■ Options during a call
Warning: Do not hold the device near your ear when the loudspeaker
is in use, because the volume may be extremely loud.
Many of the options that you can use during a call are network services.
For availability, contact your network operator or service provider.
During a call, select Options and from the following options:
Call options are Mute or Unmute, Contacts, Menu, Auto volume on or
Auto volume off, Record, Lock keypad, Audio enhancing, Loudspeaker, or
Handset.
Network services options are Answer and Reject, Hold or Unhold, New
call, Add to conference, End call, End all calls, and the following:
Send DTMF — to send tone strings
Swap — to switch between the active call and the call on hold
Transfer — to connect a call on hold to an active call and disconnect
yourself
Conference — to make a conference call that allows up to five persons to
take part in a conference call
Private call — to discuss privately in a conference call
21
Write text
4. Write text
You can enter text (for example, when writing messages) using
traditional or predictive text input. When using traditional text input,
press a number key, 1 to 9, repeatedly until the desired character
appears. In predictive text input you can enter a letter with a single
keypress.
When you are writing text, predictive text input is indicated by
and traditional text input by at the top left of the display. ,
, or appear next to the text input indicator, indicating the
character case.
To change the character case and the text input mode, press #.
indicates number mode. To change from the letter to number
mode, press and hold #, and select Number mode. To insert a special
character, press and hold *.
■ Settings
To set the writing language, select Options > Writing language.
Predictive text input is only available for the languages listed.
Select Options > Prediction on to set the predictive text input or
Prediction off to set traditional text input.
■ Predictive text input
Predictive text input is based on a built-in dictionary to which you can
add new words.
1. Start writing a word using the 2 to 9 keys. Press each key only once
for a single letter. The word changes after each keypress.
2. When you have finished writing the word and it is correct, to confirm
it, press 0 to add a space, or scroll in any direction. Press a
navigation key to move the cursor.
If the word is not correct, press * repeatedly, or select Options >
Matches. Select the correct word and Use.
22
Write text
If ? is displayed after the word, the word you intended to write is not
in the dictionary. To add the word to the dictionary, select Spell.
Enter the word (traditional text input is used), and select Save.
To enter a full stop, press 1.
3. Start writing the next word.
Write compound words
Enter the first part of the word, and scroll right to confirm it. Write the
last part of the word, and confirm the word.
■ Traditional text input
Press a number key, 1 to 9, repeatedly until the desired character
appears. Not all characters available under a number key are printed on
the key. The characters available depend on the writing language. See
“Settings,” p. 22.
If the next letter you want is located on the same key as the present one,
wait until the cursor appears, or press any of the navigation keys and
enter the letter.
The most common punctuation marks and special characters are
available under the 1 key.
23
Navigate the menus
5. Navigate the menus
The phone offers you an extensive range of functions, which are
grouped into menus.
1. To access the menu, select Menu. To change the menu view, select
Options > Main menu view > List or Grid.
2. Scroll through the menu, and select a submenu (for example,
Settings).
3. If the menu contains submenus, select the one that you want (for
example, Call).
4. If the selected menu contains further submenus, select the one that
you want (for example, Anykey answer).
5. Select the setting of your choice.
6. To return to the previous menu level, select Back. To exit the menu,
select Exit.
24
Messages
6. Messages
The message services can only be used if they are supported
by your network or your service provider.
Note: When sending messages, your phone may display Message sent.
This is an indication that the message has been sent by your device to
the message center number programmed into your device. This is not an
indication that the message has been received at the intended
destination. For more details about messaging services, check with your
service provider.
Important: Exercise caution when opening messages. Messages may
contain malicious software or otherwise be harmful to your device or
PC.
Only devices that have compatible features can receive and display
messages. The appearance of a message may vary depending on the
receiving device.
■ Text messages (SMS)
Using the short message service (SMS) you can send and receive
multipart messages made of several ordinary text messages (network
service) that can contain pictures.
Before you can send any text, picture, or e-mail message, you must save
your message center number. See “Message settings,” p. 39.
To check SMS e-mail service availability and to subscribe to the service,
contact your service provider.
Your device supports the sending of text messages beyond the character limit for
a single message. Longer messages will be sent as a series of two or more
messages. Your service provider may charge accordingly. Characters that use
accents or other marks, and characters from some language options like Chinese,
take up more space limiting the number of characters that can be sent in a single
message.
25
Messages
Write and send an SMS message
1. Select Menu > Messaging > Create message > Text message.
2. Enter a message. See “Write text,” p. 22.
At the top of the display, the message length indicator tracks the
number of available characters. For example, 10/2 means that you
can still add 10 characters for the text to be sent as two messages.
To insert text templates or a picture into the message, see
“Templates,” p. 27. Each picture message comprises several text
messages. Sending one picture or multipart message may cost more
than sending one text message.
3. To send the message, select Send > Recently used, To phone number,
To many, or To e-mail address. To send a message using a predefined
message profile, select Via sending profile. For the message profile,
see “Text and SMS e-mail,” p. 39. Select or enter a phone number or
e-mail address, or select a profile.
Read and reply to an SMS message
is shown when you received an SMS message or an SMS e-mail. The
blinking indicates that the message memory is full. Before you can
receive new messages, delete some of your old messages in the Inbox
folder.
1. To view a new message, select Show. To view it later, select Exit.
To read the message later, select Menu > Messaging > Inbox. If more
than one message is received, select the message that you want to
read. indicates an unread message.
2. While reading a message, select Options and delete or forward the
message; edit the message as a text message or an SMS e-mail;
rename the message you are reading or move it to another folder; or
view or extract message details. You can also copy text from the
beginning of the message to your phone calendar as a reminder note.
To save the picture in the Templates folder when reading a picture
message, select Save picture.
3. To reply as a message, select Reply > Text message, Multimedia msg.,
Flash message, or Audio message. Enter the reply message. When
26
Messages
replying to an e-mail, first confirm or edit the e-mail address and
subject.
4. To send the message to the displayed number, select Send > OK.
Templates
Your phone has text templates and picture templates that you
can use in text, picture, or SMS e-mail messages.
To access the template list, select Menu > Messaging > Saved items >
Text messages > Templates.
■ Multimedia messages (MMS)
A multimedia message can contain text, sound, a picture, a calendar
note, a business card, or a video clip. If the message is too large, the
phone may not be able to receive it. Some networks allow text messages
that include an Internet address where you can view the multimedia
message.
You cannot receive multimedia messages during a call, a game, another
Java application, or an active browsing session over GSM data. Because
delivery of multimedia messages can fail for various reasons, do not rely
solely upon them for essential communications.
Write and send an MMS message
To set the settings for multimedia messaging, see “Multimedia,” p. 40.
To check availability and to subscribe to the multimedia messaging
service, contact your service provider.
Copyright protections may prevent some images, music (including ringing tones),
and other content from being copied, modified, transferred or forwarded.
1. Select Menu > Messaging > Create message > Multimedia msg..
2. Enter a message. See “Write text,” p. 22.
To insert a file, select Options > Insert and from the following
options:
Image, Sound clip, or Video clip — to insert a file from Gallery
New image — to take a new image to be added to the message
27
Messages
New sound clip — to make a new recording to be added to the
message
Business card or Calendar note — to insert a business card or a
calendar note in the message
Slide — to insert a slide to the message. Your phone supports
multimedia messages that contain several pages (slides). Each slide
can contain text, one image, a calendar note, a business card, and
one sound clip. To open a desired slide if the message contains
several slides, select Options > Previous slide, Next slide, or Slide list.
To set the interval between the slides, select Options > Slide timing.
To move the text component to the top or bottom of the message,
select Options > Place text first or Place text last.
The following options may also be available: Delete to delete an
image, slide, or sound clip from the message, Clear text, Preview, or
Save message. In More options the following options may be
available: Insert contact, Insert number, Message details, and Edit
subject.
3. To send the message, select Send > Recently used, To phone number,
To e-mail address, or To many.
4. Select the contact from the list, or enter the recipient’s phone
number or e-mail address, or search for it in Contacts. Select OK. The
message is moved to the Outbox folder for sending.
While the multimedia message is being sent, the animated indicator
is displayed and you can use other functions on the phone. If the
sending fails, the phone tries to resend it a few times. If this fails, the
message remains in the Outbox folder, and you can try to resend it
later.
If you select Save sent messages > Yes, the sent message is saved in
the Sent items folder. See “Multimedia,” p. 40. When the message is
sent, it is not an indication that the message has been received at the
intended destination.
28
Messages
Read and reply to an MMS message
Important: Exercise caution when opening messages. Multimedia
message objects may contain malicious software or otherwise be
harmful to your device or PC.
When your phone receives a multimedia message, the animated is
displayed. When the message has been received, and the text
Multimedia message received are shown.
1. To read the message, select Show. To view it later, select Exit.
To read the message later, select Menu > Messaging > Inbox. In the
list of messages, indicates an unread message. Select the
message that you want to view.
2. The function of the middle selection key changes according to the
currently displayed attachment in the message.
To view the whole message if the received message contains a
presentation, a sound clip, or a video clip, select Play.
Select Options to access Attachments (for example, a business card)
and Objects (for example, images).
3. To reply to the message, select Options > Reply > Text message,
Multimedia msg., Flash message, or Audio message. Enter the reply
message, and select Send.
Select Options to access available options.
■ Memory full
When you have received a new text message and the message memory
is full, blinks and Text msgs. memory full. Delete msgs. is shown.
Select No, and delete some messages from a folder. To discard the
waiting message, select Exit > Yes.
When you have a new multimedia message waiting and the memory for
the messages is full, blinks and Multimedia memory full. View
waiting msg. is shown. To view the waiting message, select Show.
Before you can save the waiting message, delete old messages to free
memory space. To save the message, select Save.
To discard the waiting message, select Exit > Yes. If you select No, you
can view the message.
29
Messages
■ Folders
The phone saves received text and multimedia messages in the Inbox
folder.
Multimedia messages that have not yet been sent are moved to the
Outbox folder.
If you have selected Message settings > Text messages > Save sent
messages > Yes, and Message settings > Multimedia msgs. > Save sent
messages > Yes, the sent messages are saved in the Sent items folder.
To save the text message that you are writing and wish to send later in
the Saved items folder, select Options > Save message > Saved text
msgs.. For multimedia messages, select the option Save message.
indicates unsent messages.
To organize your text messages, you can move some of them to My
folders or add new folders for your messages. Select Messaging > Saved
items > Text messages > My folders.
To add a folder, select Options > Add folder. If you have not saved any
folders, select Add.
To delete or rename a folder, scroll to the desired folder, and select
Options > Delete folder or Rename folder.
■ Postcards
With the postcard messaging service you can create and send postcards
that may contain an image and a greeting text. The postcard is sent to
the service provider using multimedia messaging. The service provider
prints the post card, and sends it to the postal address given with the
message. The Multimedia messaging service must be activated before
this service can be used.
Before you can use the postcard service, you must subscribe to the service. To
check the availability and costs, and to subscribe to the service, contact your
network operator or service provider.
Send a postcard
Select Menu > Messaging > Create message > Pos tcard. Scroll to the
editor fields, and select Write to enter the name and the postal address
30
Loading...