Microsoft RM-160 User Manual

Download

Draft

Nokia N95 User guide

9249884

ISSUE 2 EN

DECLARATION OF CONFORMITY

Draft

Hereby, NOKIA CORPORATION declares that this RM-160 product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/ EC. A copy of the Declaration of Conformity can be found at http://www.nokia.com/ phones/declaration_of_conformity/.

The crossed-out wheeled bin means that within the European Union the product must be taken to separate collection at the product end-of-life. This applies to your device but also to any enhancements marked with this symbol. Do not dispose of these products as unsorted municipal

waste. For more information, see product Eco-Declaration or country specific information at www.nokia.com. © 2007 Nokia. All rights reserved. Nokia, Nokia Connecting People, Nseries, N95, and Visual Radio are trademarks or registered trademarks of Nokia Corporation. Nokia tune is a sound mark of Nokia Corporation. Other product and company names mentioned herein may be trademarks or tradenames of their respective owners.

Reproduction, transfer, distribution, or storage of part or all of the contents in this document in any form without the prior written permission of Nokia is prohibited.

US Patent No 5818437 and other pending patents. T9 text input software Copyright (C) 1997-2007. Tegic Communications, Inc. All rights reserved. Portions of the Maps software are copyright © 2007 The FreeType Project. All rights reserved. This product is licensed under the MPEG-4 Visual Patent Portfolio License (i) for personal and noncommercial use in connection with information which has been encoded in compliance with the MPEG-4 Visual Standard by a consumer engaged in a personal and noncommercial activity and (ii) for use in connection with

trademarks of Symbian Ltd. Java and all Java-based marks are trademarks or registered trade marks of Sun Microsystems, Inc.

MPEG-4 video provided by a licensed video provider. No license is granted or shall be implied for any other use. Additional information, including that related to promotional, internal, and commercial uses, may be obtained from MPEG LA, LLC. See <http://www.mpegla.com>. Nokia operates a policy of ongoing development. Nokia reserves the right to make changes and improvements to any of the products described in this document without prior notice. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, UNDER NO CIRCUMSTANCES SHALL NOKIA OR ANY OF ITS LICENSORS BE RESPONSIBLE FOR ANY LOSS OF DATA OR INCOME OR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES HOWSOEVER CAUSED. THE CONTENTS OF THIS DOCUMENT ARE PROVIDED "AS IS". EXCEPT AS REQUIRED BY APPLICABLE LAW, NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE MADE IN RELATION TO THE ACCURACY, RELIABILITY OR CONTENTS OF THIS DOCUMENT. NOKIA RESERVES THE RIGHT TO REVISE THIS DOCUMENT OR WITHDRAW IT AT ANY TIME WITHOUT PRIOR NOTICE.

The availability of particular products and applications and services for these products may vary by region. Please check with your Nokia dealer for details, and availability of language options.

Export controls This device may contain commodities, technology or software subject to export

laws and regulations from the US and other countries. Diversion contrary to law is prohibited. FCC/INDUSTRY CANADA NOTICE

Your device may cause TV or radio interference (for example, when using a telephone in close proximity to receiving equipment). The FCC or Industry Canada can require you to stop using your telephone if such interference cannot be eliminated. If you require assistance, contact your local service facility. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by Nokia could void the user's authority to operate this equipment.

The third-party applications provided with your device may have been created and may be owned by persons or entities not affiliated with or related to Nokia. Nokia does not own the copyrights or intellectual property rights to the third-party applications. As such, Nokia does not take any responsibility for end-user support,

functionality of the applications, or the information in the applications or these

Draft

materials. Nokia does not provide any warranty for the third-party applications. BY USING THE APPLICATIONS YOU ACKNOWLEDGE THAT THE APPLICATIONS ARE PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, TO THE

MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW. YOU FURTHER ACKNOWLEDGE THAT NEITHER NOKIA NOR ITS AFFILIATES MAKE ANY REPRESENTATIONS OR WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTIES OF TITLE, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR THAT THE APPLICATIONS WILL NOT INFRINGE ANY THIRD-PARTY PATENTS, COPYRIGHTS, TRADEMARKS, OR OTHER RIGHTS.

Nokia Care contact information

US: Nokia Inc. 4630 Woodland Corporate Blvd. Suite 160 Tampa FL 33614 Telephone: 1-888-NOKIA-2U (1-888-665-4228) Facsimile: 1-813-249-9619 TTY/TDD Users: 1-800-24-NOKIA (1-800-246-6542) www.nokiausa.com

Canada: Nokia Products Ltd., 601 Westney Rd. S., Ajax, ON L1S 4N7

Issue 2 EN, 9249884

Contents

Draft

For your safety........................................... 7

Support.....................................................10

Help ........................................................................................10

Nokia support and contact information .......................10

Get started ............................................................................10

Additional applications......................................................10

Your Nokia N95.......................................11

Software updates ................................................................11

Settings ..................................................................................11

Welcome................................................................................11

Transfer content from another device...........................11

Essential indicators.............................................................12

Fast downloading................................................................14

Volume and loudspeaker control ....................................14

Multimedia menu................................................................14

Keypad lock (keyguard)......................................................15

Headset ..................................................................................15

Memory card.........................................................................16

File manager ........................................................................17

Download! ............................................................................18

Web browser ...........................................19

Connection security............................................................19

Bookmarks view...................................................................19

Browse the web...................................................................20

End connection....................................................................23

Settings..................................................................................23

Connections..............................................25

Wireless LAN ........................................................................25

Connection manager .........................................................27

Bluetooth connectivity .....................................................27

Infrared connection ........................................................... 31

USB ........................................................................................31

PC connections ....................................................................32

Synchronization .................................................................32

Device manager ..................................................................32

Modem ..................................................................................33

Media applications ..................................34

Music player ........................................................................34

Radio .....................................................................................38

Video center ........................................................................39

RealPlayer ............................................................................41

Adobe Flash Player .............................................................42

Draft

Nokia Lifeblog .....................................................................42

Camera..................................................... 46

Take pictures.........................................................................46

Take pictures in a sequence..............................................51

You in the picture—self-timer .........................................51

Record videos........................................................................52

Gallery ..................................................... 55

View and browse files ........................................................55

Print Basket...........................................................................57

Albums....................................................................................57

Free memory .........................................................................58

Back-up files.........................................................................58

Edit images............................................................................58

Edit video clips .....................................................................59

Slide show .............................................................................61

TV out mode..........................................................................61

Presentations........................................................................62

Image print............................................................................63

Movie director......................................................................63

Print online............................................................................65

Online sharing ......................................................................65

Home network .....................................................................66

Positioning................................................70

GPS receiver..........................................................................71

About satellite signals .......................................................71

Position requests.................................................................72

Maps ......................................................................................72

Landmarks ............................................................................75

GPS data ...............................................................................76

Personalize your device...........................78

Profiles—set tones ..............................................................78

3-D tones .............................................................................79

Change the look of your device .....................................80

Active standby mode..........................................................80

Time management ...................................82

Clock ......................................................................................82

Calendar ...............................................................................82

Messaging ...............................................85

Write text..............................................................................86

Write and send messages.................................................86

Inbox—receive messages ..................................................87

Mailbox .................................................................................88

View messages on a SIM card.........................................90

Messaging settings.............................................................90

Make calls ................................................95

Draft

Voice calls..............................................................................95

Answer or decline a call....................................................98

Log ..........................................................................................98

Tools....................................................... 108

Application manager .......................................................108

Digital rights management ...........................................110

Voice commands ..............................................................111

Contacts (Phonebook) ......................... 100

Save and edit names and numbers ............................. 100

Copy contacts....................................................................101

Add ringing tones for contacts.....................................102

Create contact groups .................................................... 102

Office..................................................... 103

Quickoffice ........................................................................103

Notes ................................................................................... 104

Recorder .............................................................................104

Adobe Reader ...................................................................104

Calculator ..........................................................................105

Converter ...........................................................................105

Zip manager ...................................................................... 105

Wireless Keyboard ........................................................... 106

Barcode reader .................................................................106

Settings ................................................ 112

General ................................................................................112

Phone ..................................................................................117

Connection ........................................................................119

Applications .......................................................................123

Troubleshooting: Q&A ......................... 124

Battery information ............................. 127

Charging and discharging...............................................127

Nokia battery authentication guidelines ...................127

Care and maintenance ......................... 129

Additional safety information............. 130

Index ...................................................... 133

For your safety

Draft

Read these simple guidelines. Not following them may be dangerous or illegal. Read the complete user guide for further information.

SWITCH ON SAFELY Do not switch the device on when wireless phone use is prohibited or when it may cause interference or danger.

ROAD SAFETY COMES FIRST Obey all local laws. Always keep your hands free to operate the vehicle while driving. Your first consideration while driving should be road safety.

INTERFERENCE All wireless devices may be susceptible to interference, which could affect performance.

SWITCH OFF IN HOSPITALS Follow any restrictions. Switch the device off near medical equipment.

SWITCH OFF IN AIRCRAFT Follow any restrictions. Wireless devices can cause interference in aircraft.

SWITCH OFF WHEN REFUELING Do not use the device at a refueling point. Do not use near fuel or chemicals.

SWITCH OFF NEAR BLASTING Follow any restrictions. Do not use the device where blasting is in progress.

USE SENSIBLY Use only in the normal position as explained in the product documentation. Do not touch the antenna unnecessarily.

QUALIFIED SERVICE Only qualified personnel may install or repair this product.

ENHANCEMENTS AND BATTERIES Use only approved enhancements and batteries. Do not connect incompatible products.

WATER-RESISTANCE Your device is not water-resistant. Keep it dry.

BACK-UP COPIES Remember to make backup copies or keep a written record of all important information stored in your device.

CONNECTING TO OTHER DEVICES When

Draft

connecting to any other device, read its user guide for detailed safety instructions. Do not connect incompatible products.

EMERGENCY CALLS Ensure the phone function of the device is switched on and in service. Press the end key as many times as needed to clear the display and return to the standby mode. Enter the emergency number, then press the call key. Give your location. Do not end the call until given permission to do so.

About your device

The wireless device described in this guide is approved for use on the (E)GSM 850, 900, 1800 and 1900 MHz, and WCDMA (HSDPA) 850 and 1900 MHz networks. Contact your service provider for more information about networks.

When using the features in this device, obey all laws and respect local customs, privacy and legitimate rights of others, including copyrights.

Copyright protections may prevent some images, music (including ringing tones), and other content from being copied, modified, transferred, or forwarded.

Your device supports internet connections and other methods of connectivity. Like computers, your device may

be exposed to viruses, malicious messages and applications, and other harmful content. Exercise caution and open messages, accept connectivity requests, download content, and accept installations only from trustworthy sources. To increase the security of your device, consider installing antivirus software with a regular update service and using a firewall application.

Warning: To use any features in this device, other

than the alarm clock, the device must be switched on. Do not switch the device on when wireless device use may cause interference or danger.

The office applications support common features of Microsoft Word, PowerPoint, and Excel (Microsoft Office 2000, XP, and 2003). Not all file formats can be viewed or modified.

During operation, such as an active high-speed data connection, the device may feel warm. In most cases, this condition is normal. If you suspect the device is not working properly, take it to the nearest authorized service facility.

Your device may have preinstalled bookmarks and links for third-party internet sites. You may also access other thirdparty sites through your device. Third-party sites are not affiliated with Nokia, and Nokia does not endorse or assume liability for them. If you choose to access such sites, you should take precautions for security or content.

The images in this guide may differ from your device

Draft

display.

Network services

To use the phone you must have service from a wireless service provider. Many of the features require special network features. These features are not available on all networks; other networks may require that you make specific arrangements with your service provider before you can use the network services. Your service provider can give you instructions and explain what charges will apply. Some networks may have limitations that affect how you can use network services. For instance, some networks may not support all language-dependent characters and services.

Your service provider may have requested that certain features be disabled or not activated in your device. If so, these features will not appear on your device menu. Your device may also have a special configuration such as changes in menu names, menu order, and icons. Contact your service provider for more information.

This device supports WAP 2.0 protocols (HTTP and SSL) that run on TCP/IP protocols. Some features of this device, such as MMS, browsing, and e-mail require network support for these technologies.

Enhancements, batteries, and chargers

Always switch the device off and disconnect the charger before removing the battery.

Check the model number of any charger before use with this device. This device is intended for use when supplied with power from a DC-4, AC-4, or AC-5 charger and from an AC-1, ACP-8, ACP-9, ACP-12U, or LCH-12 charger when used with the CA-44 charger adapter.

The battery intended for use with this device is BL-5F.

Warning: Use only batteries, chargers, and

enhancements approved by Nokia for use with this particular model. The use of any other types may invalidate any approval or warranty, and may be dangerous.

For availability of approved enhancements, please check with your dealer. When you disconnect the power cord of any enhancement, grasp and pull the plug, not the cord.

Support

Draft

Model number: Nokia N95-3

Support

Hereinafter referred to as Nokia N95.

Help

Your device has context-sensitive help. When an application is open, select Options > Help to access help for the current view.

When you are reading the instructions, to switch between help and the application that is open in the background, press and hold .

To open help from the main menu, select Applications >

Help. Select the desired application to view its help topics.

Nokia support and contact information

Check www.nseries.com/support or your local Nokia website for the latest version of this guide, additional information, downloads, and services related to your Nokia product.

On the website, you can get information on the use of Nokia products and services. If you need to contact customer service, check the list of local Nokia contact centers at www.nokia.com/customerservice

For maintenance services, check your nearest Nokia service center at www.nokia.com/repair

Get started

See the Get started guide for keys and parts information and instructions for setting up the device for use.

Additional applications

There are various applications provided by Nokia and different third-party software developers to help you do more with your Nokia N95. These applications are explained in the Additional applications leaflet which is available at the Nokia N95 product support pages at

www.nseries.com/support

or your local Nokia web site.

Your Nokia N95

Draft

Software updates

Nokia may produce software updates that may offer new features, enhanced functions, or improved performance. You may be able to request these updates through the Nokia Software Updater PC application. To update the device software, you need the Nokia Software Updater application and a compatible PC with Microsoft Windows 2000 or XP operating system, broadband internet access, and a compatible data cable to connect your device to the PC.

To get more information and to download the Nokia Software Updater application, visit www.nokia.com/

softwareupdate or your local Nokia web site.

Settings

Your device normally has MMS, GPRS, streaming, and mobile internet settings automatically configured in the device, based upon your wireless service provider information. You may have settings from your service providers already installed in your device, or you may receive or request the settings from the service providers as a special message.

Welcome

When you switch on your device for the first time,

Welcome opens. Select from the following:

• Sett. wizard—to configure various settings. See the

Additional applications leaflet.

• Transfer—to transfer content, such as contacts and

calendar entries, from a compatible Nokia device. See ‘Transfer content from another device’, p. 11.

To open the Welcome later, press , and select

Applications > Welcome. You can also access the

individual applications in their own menu locations.

Transfer content from another device

You can transfer content, such as contacts, from a compatible Nokia device to your Nokia N95 using Bluetooth connectivity or infrared. Your device notifies you if the other device is not compatible.

The type of content that can be transferred depends on the model of the device from which you want to transfer content. If the other device supports synchronization, you

Your Nokia N95

can also synchronize data between the other device and

Draft

your Nokia N95.

If the other device cannot be powered on without a SIM card, you can insert your SIM card in it. When Nokia N95 is switched on without a SIM card, the offline profile is automatically activated.

Transfer content

Your Nokia N95

1 To use the application for the first time, on your Nokia

N95, select it in the Welcome application, or press , and select Tools > Transfer. If you have used the application before and want to start a new transfer, select Transfer data.

2 Select whether you want to use Bluetooth connectivity

or infrared to transfer the data. Both devices must support the selected connection type.

3 If you select Bluetooth connectivity:

To have Nokia N95 search for devices with Bluetooth connectivity, select Continue. Select the device from which you want to transfer content from the list. You are asked to enter a code on your Nokia N95. Enter a code (1-16 digits), and select OK. Enter the same code on the other device, and select OK. The devices are now paired. See ‘Pair devices’, p. 29. For some phone models, the Data transfer application is sent to the other device as a message. To install Data

transfer on the other device, open the message, and

follow the instructions on the display.

If you select infrared, connect the two devices. See ‘Infrared connection’, p. 31.

4 From your Nokia N95, select the content you want to

transfer from the other device.

Content is transferred from the memory of the other device to the corresponding location in your Nokia N95. Transferring time depends on the amount of data to be transferred. You can cancel transferring and continue later.

If the other device supports synchronization, you can keep the data up-to-date in both devices. To start a synchronization with a compatible Nokia device, select

Phones, scroll to the device, and select Options > Synchronize. Follow the instructions on the display.

The synchronization is two-way, and the data in both devices is made the same. If an item is deleted from either device, it is deleted from the other device as well when synchronizing; you cannot restore deleted items with synchronization.

To view the log of a previous transfer, select Transfer log.

Essential indicators

The device is being used in a GSM network.

The device is being used in a WCDMA network

(network service).

HSDPA support in the device is activated and the

Draft

device being used in a WCDMA network that supports HSDPA (network service).

You have one or more unread messages in the Inbox

folder in Messaging.

You have received new e-mail in the remote mailbox.

There are messages waiting to be sent in the Outbox

folder.

You have missed calls.

Shown if Ringing type is set to Silent and Message

alert tone, and E-mail alert tone are set to Off.

The device keypad is locked.

A clock alarm is active.

The second phone line is being used (network service).

All calls to the device are forwarded to another number. If you have two phone lines (network service), a number indicates the active line.

A compatible headset is connected to the device.

indicates the connection has been lost.

A compatible TV out cable is connected to the device.

A compatible TTY is connected to the device.

A data call is active.

A GPRS packet data connection is active. indicates the connection is on hold and that a connection is available.

A packet data connection is active in a part of the network that supports EDGE. indicates the connection is on hold and that a connection is available. The icons indicate that EDGE is available in the network, but your device is not necessarily using EDGE in the data transfer.

A WCDMA packet data connection is active. indicates the connection is on hold and that a connection is available.

You have set the device to scan for WLANs, and a

WLAN is available. See ‘Wireless LAN’, p. 25.

A WLAN connection is active in a network that has

encryption.

A WLAN connection is active in a network that does

not have encryption.

Bluetooth connectivity is on.

Data is being transmitted using Bluetooth connectivity. When the indicator is blinking, your device is trying to connect with another device.

A USB connection is active.

Your Nokia N95

An infrared connection is active. If the indicator is

Draft

blinking, the device is trying to connect to the other device or the connection has been lost.

Fast downloading

You can activate or deactivate support for high-speed downlink packet access (HSDPA, also called 3.5G) in the

Your Nokia N95

device settings. See ‘Packet data’, p. 122.

HSDPA is a network service in WCDMA networks and it provides high data download speed. When HSDPA support in the device is activated and the device is connected to a WCDMA network that supports HSDPA, downloading data such as messages, e-mail, and browser pages through the cellular network may be faster.

For availability and subscription to data connection services, contact your service provider.

HSDPA only affects the download speed; sending data to the network, such as sending messages and e-mail, is not affected.

Volume and loudspeaker control

To increase or decrease the volume level when you have

an active call or are listening to a sound, press the volume key.

The built-in loudspeaker allows you to speak and listen from a short distance without having to hold the device to your ear.

Warning: Do not hold the device near your ear when

the loudspeaker is in use, because the volume may be

extremely loud.

To use the loudspeaker during a call, select Options >

Activate loudspeaker.

To turn off the loudspeaker, select Options > Activate

handset.

Multimedia menu

The multimedia menu provides quick access to multimedia content and predefined applications.

To open the multimedia menu, press , or when the device is in the standby mode, open the media keys under the 2-way slide.

To scroll in the multimedia menu, use the scroll key. To

Draft

scroll faster, press and hold the key. To open an application, press .

To change the shown shortcuts, select Options > Menu

items. You can delete, add, or rearrange shortcuts to

applications, browser bookmarks, and radio channels defined in Radio.

You can customize the appearance of the multimedia menu. To change the images shown in the background, select Options > Background images and the desired option. To set zooming and panning on or off, select

Options > Image effects. To set sounds on or off, select Options > Menu sounds.

Keypad lock (keyguard)

To lock the keys, press , then .

To unlock the keys, open the 2-way slide, or press , then

You can have the keypad lock activated automatically after a time-out or when the 2-way slide is closed. See ‘Security’, p. 114

When the keypad lock is on, calls may be possible to the official emergency number programmed into your device.

Headset

You can connect a compatible headset or compatible headphones to the Nokia AV Connector (3.5 mm) of your device. You may need to select the cable mode.

Do not connect products that create an output signal as this may cause damage to the device. Do not connect any voltage source to the Nokia AV Connector.

When connecting any external device or any headset, other than those approved by Nokia for use with this device, to the Nokia AV Connector, pay special attention to volume levels.

Warning: When you use the headset, your ability to

hear outside sounds may be affected. Do not use the headset where it can endanger your safety.

To use a headset or headphones with a remote control unit, for example, the Nokia Audio Controller AD-43, connect the unit to the connector in the device, then connect the headset or headphones to the unit.

Some headsets do not include a microphone. For phone calls, use such a headset with a remote control unit or the microphone of the device.

Your Nokia N95

When using certain headset enhancements, for example,

Draft

the Nokia Audio Controller AD-43, to adjust the volume during a call, use the volume key in the device. The Nokia Audio Controller AD-43 has multimedia volume controls that are used to adjust the volume only for music or video playback.

Your Nokia N95

Memory card

Use only compatible microSD cards approved by Nokia for use with this device. Nokia uses approved industry standards for memory cards, but some brands may not be fully compatible with this device. Incompatible cards may damage the card and the device and corrupt data stored on the card.

Keep all memory cards out of the reach of small children.

Insert the memory card

1 Place your finger

in the recess

below the door of

the memory card

slot, and lift the

door. Pull the

door to the right

to reveal the

hinge, and swing

the door to the

side.

2 Insert a compatible

memory card in the

slot. Make sure that

the contact area on

the card is facing up

and towards the slot.

3 Push the card in. You

can hear a click when the card

locks into place.

4 Push the hinge back in, and close

Draft

the door. Ensure that the door is properly closed.

Eject the memory card

Important: Do not remove the

memory card in the middle of an operation when the card is being accessed. Removing the card in the middle of an operation may damage the memory card as well as the device, and data stored on the card may be corrupted.

1 Before you eject the card, press , and select

Remove memory card. All applications are closed.

2 When Removing memory card will close all open

applications. Remove anyway? is displayed, select Yes.

3 When Remove memory card and press 'OK' is

displayed, open the door of the memory card slot.

4 Press the memory card to release it from the slot. 5 Pull out the memory card. If the device is switched on,

select OK.

Memory card tool

Press , and select Tools > Memory.

To back up information from the device memory to a compatible memory card (if available), select Options >

Back up phone memory. The device notifies you if the

memory card does not have enough free space to create a back-up.

To restore information from the compatible memory card to the device memory, select Options > Restore from

card.

When a memory card is reformatted, all data on the card is permanently lost. Some memory cards are supplied preformatted and others require formatting. Consult your retailer to find out if you must format the memory card before you can use it.

To format a memory card, select Options > Format

memory card. Select Yes to confirm.

File manager

To browse files and folders in the device memory or on a compatible memory card (if inserted), press , and select

Tools > File mgr.. The device memory view ( ) opens.

Press to open the memory card view ( ), if available.

To mark several files, press and hold while you press

, , or . To move or copy the files to a folder, select

Options > Move to folder or Copy to folder.

To find a file, select Options > Find and the memory from which to search. Enter a search text that matches the file name.

Your Nokia N95

To view what types of data you have in the device and how

Draft

much memory the different data types consume, select

Options > Memory details. The amount of available free

memory is shown in Free memory.

Memory low—free memory

Many features of the device use memory to store data. The

Your Nokia N95

device notifies you if the device or the memory card memory is low.

To free device memory, transfer data to a compatible memory card (if available) or to a compatible PC.

To remove data to free memory, use File mgr. to delete files you no longer need, or go to the respective application. For example, you can remove the following:

• Messages in the folders in Messaging and retrieved

e-mail messages from the mailbox

• Saved web pages

• Contact information

• Calendar notes

• Applications shown in App. mgr. that you do not need

• Installation files (.sis) of applications you have installed

to a compatible memory card; first back up the installation files to a compatible PC

Download!

With Download!, you can browse, download, and install items, such as applications and media files, to your device from the internet.

Press , and select Download!. The items are categorized under catalogs and folders provided by different service providers. Some items may be chargeable, but you can usually preview them free of charge.

Web browser

Draft

Press , and select Web (network service).

Shortcut: To start Web, press and hold in the

standby mode.

With Web, you can view hypertext markup language (HTML) web pages on the internet as originally designed. You can also browse web pages that are designed specifically for mobile devices, and use extensible hypertext markup language (XHTML), or the wireless markup language (WML).

With Web, you can zoom in and out on a page, use Mini

map and Page overview to navigate on pages, read web

feeds and blogs, bookmark web pages, and download content, for example.

Check the availability of services, pricing, and fees with your service provider. Service providers will also give you instructions on how to use their services.

To use Web, you need an access point to connect to internet. See ‘Access points’, p. 120.

Connection security

If the security indicator is displayed during a connection, the data transmission between the device and the internet gateway or server is encrypted.

The security icon does not indicate that the data transmission between the gateway and the content server (or place where the requested resource is stored) is secure. The service provider secures the data transmission between the gateway and the content server.

Security certificates may be required for some services, such as banking services. You are notified if the identity of the server is not authentic or if you do not have the correct security certificate in your device. For more information, contact your service provider. See also ‘Certificate management’, p. 115 for more information on the certificates and certificate details.

Bookmarks view

The bookmarks view allows you to select web addresses from a list or from a collection of bookmarks in the Auto.

Bookmarks folder. You can also enter the URL address of

the web page you want to visit directly into the field ( ).

Web browser

indicates the starting page defined for the default

Draft

access point.

You can save URL addresses as bookmarks while browsing on the internet. You can also save addresses received in messages to your bookmarks and send saved bookmarks.

Web browser

To open the bookmarks view while browsing, press , or select Options > Bookmarks.

To edit the details of a bookmark, such as the title, select

Options > Bookmark manager > Edit.

In the bookmarks view, you can also enter other browser folders. Web allows you to save web pages during browsing. In the Saved pages folder, you can view the content of the pages you have saved offline.

Web also keeps track of the web pages you visit during

browsing. In the Auto. Bookmarks folder, you can view the list of visited web pages.

In Web Feeds, you can view saved links to web feeds and blogs to which you have subscribed. Web feeds are commonly found on major news organization web pages,

personal weblogs, online communities that offer latest headlines, and article summaries. Web feeds use RSS and ATOM technologies.

Browse the web

Important: Use only services that you trust and that

offer adequate security and protection against harmful software.

With Web, you can view web pages as they are originally designed. To browse a web page, in the bookmarks view, select a bookmark, or enter the address in the field ( ). Then press .

Some web pages may contain material, such as graphics and sounds, that requires a large amount of memory to view. If your device runs out of memory while loading such a page, the graphics on the page are not shown. To browse web pages without graphics to save memory, select

Options > Settings > Page > Load content > Text only.

Tip! To return to the standby mode with the browser

open in the background, press twice or . To

return to the browser, press and hold , and select

the browser from the list.

To open links and make selections, press .

To enter a new web page address you want to visit, select

Options > Go to web address.

Tip! To visit a web page saved as bookmark in the

Draft

bookmarks view, while browsing, press , and select a bookmark.

To retrieve the latest content of the page from the server, select Options > Navigation options > Reload.

To save the web address of the current page as bookmark, select Options > Save as bookmark.

To use Visual history to view snapshots of the pages you have visited during the current browsing session, select

Back (available if History list is set on in the browser

settings). To go to a previously visited page, select the page.

To save a page while browsing, select Options > Tools >

Save page. You can save pages to the device memory or

compatible memory card (if inserted), and browse them when offline. You can also group the pages into folders. To access the pages later, in the bookmarks view, select Saved

pages.

To open a sublist of commands or actions for the currently open page, select Options > Service options (if supported by the web page).

To allow or prevent the automatic opening of multiple windows, select Options > Window > Block pop-ups or

Allow pop-ups.

Shortcuts while browsing are as follows:

• Press to open your bookmarks.

• Press to search for keywords in the current page.

• Press to return to the previous page.

• Press to list all open windows.

• Press to show the page overview of the current

page. Press again to zoom in and view the desired section of the page.

• Press to enter a new web address.

• Press to go to the start page.

• Press or to zoom the page in or out.

Text search

To search for keywords within the current web page, select

Options > Find > Text, and enter a keyword. To go to the

previous match, press . To go to the next match, press

Tip! To search for keywords within the page, press

Browser toolbar

With the toolbar, you can select most frequently used features in the browser. To open the toolbar, press on an empty spot on a web page. To move within the toolbar, press or , To select a feature, press .

In the toolbar, select from the following:

Web browser

• Frequently used links to view a list of the web

Draft

addresses you visit frequently

• Page overview to view the overview of the current web

page

• Find to search for keywords within the current page

• Reload to refresh the page

Web browser

• Subscribe (if available) to view a list of available web

feeds on the current web page, and subscribe to a web feed

Download and purchase items

You can download items such as ringing tones, images, operator logos, themes, and video clips. These items can be provided free of charge, or you can purchase them. Downloaded items are handled by the respective applications in your device, for example, a downloaded photo or an .mp3 file can be saved in Gallery.

Important: Only install and use applications and

other software from trusted sources, such as applications that are Symbian Signed or have passed the Java Verified testing.

1 To download the item, select the link. 2 Select the appropriate option to purchase the item (for

example, “Buy”).

3 Carefully read all the information provided.

To continue the download, select Accept. To cancel the

download, select Cancel.

When you start a download, a list of ongoing and completed downloads from the current browsing session is displayed. To also view the list, select Options >

Downloads. In the list, scroll to an item, and select Options

to cancel ongoing downloads, or open, save, or delete completed downloads.

Mini map

Mini map helps you to navigate on web pages that contain

large amount of information. When Mini map is set on in the browser settings and you scroll through a large web page, Mini map opens and shows an overview of the web page you browse. To scroll in Mini map, press , , , or . When you find the desired location, stop scrolling, and Mini map disappears and leaves you at the selected location.

To set Mini map on, select Options > Settings >

General > Mini map > On.

Page overview

When you are browsing a web page that contains a large amount of information, you can use Page overview to view what kind of information the page contains.

To show the page overview of the current page, press .

Draft

To find the desired spot on the page, press , , , or

. Press again to zoom in and view the desired

section of the page.

Web feeds and blogs

Web feeds are xml files on web pages that are widely used by the weblog community and news organizations to share the latest entry headlines or full text, for example, recent news in the form of news feeds. Blogs or weblogs are web diaries. Most of the web feeds use RSS and ATOM technologies. It is common to find web feeds on web, blog, and wiki pages.

Web automatically detects if a web page contains web

feeds. To subscribe to a web feed, select Options >

Subscribe, or click on the link. To view the web feeds to

which you have subscribed, in the bookmarks view, select

Web feeds.

To update a web feed, select it, and Options > Refresh.

To define how the web feeds are updated, select Options >

Settings > Web feeds. See ‘Settings’, p. 23.

End connection

To end the connection and view the browser page offline, select Options > Tools > Disconnect; or to end the connection and close the browser, select Options > Exit.

Pressing does not end the connection but takes the browser to the background.

To delete the information the network server collects about your visits to various web pages, select Options >

Clear privacy data > Delete cookies.

Empty the cache

The information or services you have accessed are stored in the cache memory of the device.

A cache is a memory location that is used to store data temporarily. If you have tried to access or have accessed confidential information requiring passwords, empty the cache after each use. The information or services you have accessed are stored in the cache. To empty the cache, select Options > Clear privacy data > Clear cache.

Settings

Select Options > Settings and from the following:

General settings

Web browser

Access point—Change the default access point. See

Draft

‘Connection’, p. 119. Some or all access points may be preset for your device by your service provider; you may not be able to change, create, edit, or remove them.

Homepage—Define the home page.

Web browser

Mini map—Set Mini map on or off. See ‘Mini map’, p. 22.

History list—While browsing, to use the selection key Back

to see a list of the pages you have visited during the current browsing session, set History list on.

Security warnings—Hide or show security notifications.

Java/ECMA script—Enable or disable the use of scripts.

Page settings

Load images and sounds—Select whether you want to

load images and other objects while browsing. If you select

Text only, to load images or objects later during browsing,

select Options > Tools > Load images.

Screen size—Select between Full screen and the normal

view with the options list.

Default encoding—If text characters are not shown

correctly, you can select another encoding according to language for the current page.

Block pop-ups—Allow or block automatic opening of

different pop-ups while browsing.

Automatic reload—If you want the web pages to be

refreshed automatically while browsing, select On.

Font size—Define the font size that is used for web pages.

Privacy settings

Auto. bookmarks—Enable or disable automatic bookmark

collecting. If you want to continue saving the addresses of the visited web pages into the Auto. Bookmarks folder, but hide the folder from the bookmarks view, select Hide

folder.

Form data saving—If you do not want the data you enter

to different forms on a web page to be saved and used next time the page is entered, select Off.

Cookies—Enable or disable the receiving and sending of

cookies.

Web feeds settings

Automatic updates—Define whether you want the web

feeds to be updated automatically or not, and how often you want to update them. Setting the application to retrieve web feeds automatically may involve the transmission of large amounts of data through your service provider's network. Contact your service provider for information about data transmission charges.

Acc. point for auto-update (only available when Automatic updates is on)—Select the desired access point

for updating.

Connections

Draft

Wireless LAN

Your device supports wireless local area network (WLAN). With WLAN, you can connect your device to the internet and compatible devices that have WLAN. For information about using your device with other compatible Universal Plug and Play (UPnP) devices through WLAN, see ‘Home network’, p. 66.

To use WLAN, it must be available in the location and your device must be connected to the WLAN.

Some places, like France, have restrictions on the use of WLAN. Check with your local authorities for more information.

Features using WLAN, or allowing such features to run in the background while using other features, increase the demand on battery power and reduce the battery life.

Your device supports the following WLAN features:

• IEEE 802.11b/g standard

• Operation at a frequency of 2.4 GHz

• Wired equivalent privacy (WEP) with keys up to 128

bits, Wi-Fi protected access (WPA), and 802.1x encryption methods. These functions can be used only if they are supported by the network.

Wireless LAN connections

To use WLAN, you must create an internet access point (IAP) in a WLAN. Use the access point for applications that need to connect to the internet. See ‘WLAN internet access points’, p. 26.

Important: Always enable one of the available

encryption methods to increase the security of your WLAN connection. Using encryption reduces the risk of unauthorized access to your data.

A WLAN connection is established when you create a data connection using a WLAN internet access point. The active WLAN connection ends when you end the data connection. To end the connection, see ‘Connection manager’, p. 27.

You can use WLAN during a voice call or when packet data is active. You can only be connected to one WLAN access point device at a time, but several applications can use the same internet access point.

When the device is in the Offline profile, you can still use WLAN (if available). Remember to comply with any applicable safety requirements when establishing and using a WLAN connection.

Connections

Tip! To check the unique media access control (MAC)

Draft

address that identifies your device, enter

*#62209526# in the standby mode.

WLAN wizard

Connections

The WLAN wizard helps you to connect to a WLAN and manage your WLAN connections.

The WLAN wizard shows the status of your WLAN connections in the active standby mode. To view the available options, scroll to the row showing the status, and press .

If the search results of found WLANs, for example, WLAN

network found are displayed, to create an internet access

point and start the web browser using this IAP, select the status, the option Start web browsing, and the network.

If you select a secured WLAN network, you are asked to enter the relevant passcodes. To connect to a hidden network, you must enter the correct network name (service set identifier, SSID). To create a new access point for hidden WLAN, select New WLAN.

If you are connected to a WLAN, the IAP name is displayed. To start the web browser using this IAP, select the status and the option Cont. Web browsing. To end the connection in the WLAN, select the status and the option

Disconnect WLAN.

If WLAN scanning is off and you are not connected to any WLAN, WLAN scanning off is displayed. To set scanning on and search for available WLANs, select the status and press .

To start a search for available WLANs, select a status and the option Search for WLAN. To set WLAN scanning off, select a status and the option Switch WLAN scan off.

To access the WLAN wizard in the menu, press , and select Tools > WLAN wiz.

WLAN internet access points

To search for WLANs available within range, press , and select Tools > WLAN wiz..

Select Options and select from the following:

• Filter WLAN networks— Filter out WLANs in the list of

found networks. The selected networks are filtered out

the next time the application searches for WLANs.

• Details — View the details of a network shown in the

list. If you select an active connection, the connection

details are displayed.

• Define access point— Create an internet access point

(IAP) in a WLAN.

• Edit access point — Edit the details of an existing IAP.

You can also use Conn. mgr. to create internet access points. See ‘Wireless LAN’, p. 27.

Operating modes

Draft

There are two operating modes in WLAN: infrastructure and ad hoc.

The infrastructure operating mode allows two kinds of communication: wireless devices are connected to each other through a WLAN access point device, or wireless devices are connected to a wired LAN through a WLAN access point device.

In the ad hoc operating mode, devices can send and receive data directly with each other. To create an internet access point for an ad hoc network, see ‘Access points’, p. 120.

Connection manager

Data connections

Press , and select Tools > Conn. mgr. > Active data

connections. In the active connections view, you can see

the open data connections: data calls ( ), packet data connections ( or ), and WLAN connections ( ).

Note: The actual time invoiced for calls by your

service provider may vary, depending on network features, rounding off for billing, and so forth.

To end a connection, select Options > Disconnect. To close all open connections, select Options > Disconnect all.

To view the details of a connection, select Options >

Details. The details shown depend on the connection type.

Wireless LAN

To search for WLANs available within range, press , and select Tools > Conn. mgr. > Available WLAN networks.

The available WLAN view shows a list of WLANs within range, their network mode (Infrastructure or Ad-hoc), and signal strength indicator. is shown for networks with encryption, and if your device has an active connection in the network.

To view the details of a network, select Options > Details.

To create an internet access point in a network, select

Options > Define access point.

Bluetooth connectivity

You can connect wirelessly to other compatible devices with wireless Bluetooth technology. Compatible devices may include mobile phones, computers, and enhancements such as headsets and car kits. You can use Bluetooth connectivity to send images, video clips, music and sound clips, and notes; connect wirelessly to your compatible PC (for example, to transfer files); connect to a compatible printer to print images with Image print. See ‘Image print’, p. 63.

Connections

Since devices with Bluetooth wireless technology

Draft

communicate using radio waves, your device and the other device do not need to be in direct line-of-sight. The two devices only need to be within 10 meters (33 feet) of each other, but the connection may be subject to interference from obstructions such as walls or from other electronic

Connections

devices.

This device is compliant with Bluetooth Specification 2.0 supporting the following profiles: Advanced Audio Distribution Profile, Audio/Video Remote Control Profile, Generic Audio/Video Distribution Profile, Basic Imaging Profile, Basic Printing Profile, Dial-up Networking Profile, File transfer Profile, Hands-Free Profile, Headset Profile, Human Interface Device Profile, Object Push Profile, Remote SIM Access profile, and Synchronization Profile.

To ensure interoperability between other devices supporting Bluetooth technology, use Nokia approved enhancements for this model. Check with the manufacturers of other devices to determine their compatibility with this device.

There may be restrictions on using Bluetooth technology in some locations. Check with your local authorities or service provider.

Features using Bluetooth technology, or allowing such features to run in the background while using other

features, increase the demand on battery power and reduce the battery life.

When the device is locked, you cannot use Bluetooth connectivity. See ‘Phone and SIM card’, p. 114 for more information on locking the device.

Settings

Press , and select Tools > Bluetooth. When you open the application for the first time, you are asked to define a name for your device.

Select from the following:

Bluetooth—To connect wirelessly to another compatible

device, first set Bluetooth connectivity On, then establish a connection. To switch off Bluetooth connectivity, select

Off.

My phone's visibility—To allow your device to be found by

other devices with Bluetooth wireless technology, select

Shown to all. To set a time after which the visibility is set

from shown to hidden, select Define period. To hide your device from other devices, select Hidden.

My phone's name—Edit the name shown to other devices

using Bluetooth wireless technology.

Remote SIM mode—To enable another device, such as a

compatible car kit enhancement, to use the SIM card in

your device to connect to the network, select On. For more

Draft

information, see ‘Remote SIM mode’, p. 30.

Security tips

When you are not using Bluetooth connectivity, select

Bluetooth > Off or My phone's visibility > Hidden. In this

way, you can better control who can find your device with Bluetooth wireless technology, and connect to it.

Do not pair with or accept connection requests from an unknown device. In this way, you can better protect your device from harmful content.

Send data using Bluetooth connectivity

Several Bluetooth connections can be active at a time. For example, if you are connected to a compatible headset, you can also transfer files to another compatible device at the same time.

For Bluetooth connectivity indicators, see ‘Essential indicators’, p. 27.

Tip! To send text using Bluetooth connectivity, open

Notes, write the text, and select Options > Send > Via Bluetooth.

1 Open the application where the item you want to send

is stored. For example, to send an image to another compatible device, open Gallery.

2 Select the item and Options > Send > Via Bluetooth.

Devices with Bluetooth wireless technology within range start to appear on the display. Device icons: computer, phone, audio or video device, and other device. To interrupt the search, select Stop.

3 Select the device with which you want to connect. 4 If the other device requires pairing before data can be

transmitted, a tone sounds, and you are asked to enter a passcode. See ‘Pair devices’, p. 29.

5 When the connection has been established, Sending

data is shown.

Tip! When searching for devices, some devices may

show only the unique address (device address). To find the unique address of your device, enter the code

*#2820# in the standby mode.

Pair devices

To pair with compatible devices and view your paired devices, in the Bluetooth application main view, press .

Before pairing, create your own passcode (1-16 digits), and agree with the owner of the other device to use the same code. Devices that do not have a user interface have a factory-set passcode. The passcode is used only once.

Connections

1 To pair with a device, select Options > New paired

Draft

device. Devices with Bluetooth wireless technology

within range start to appear on the display.

2 Select the device, and enter the passcode. The same

passcode must be entered on the other device as well.

Connections

Some audio enhancements connect automatically to your device after pairing. Otherwise, scroll to the enhancement, and select Options > Connect.

Paired devices are indicated by in the device search.

To set a device as authorized or unauthorized, scroll to a device, select Options, and select from the following:

Set as authorized—Connections between your device and

this device can be made without your knowledge. No separate acceptance or authorization is needed. Use this status for your own devices, such as your compatible headset or PC, or devices that belong to someone you trust.

indicates authorized devices in the paired devices view.

Set as unauthorized—Connection requests from this

device must be accepted separately every time.

To cancel a pairing, scroll to the device, and select

Options > Delete. If you want to cancel all pairings, select Options > Delete all.

Receive data using Bluetooth connectivity

When you receive data through Bluetooth connectivity, a tone sounds, and you are asked if you want to accept the message. If you accept, is shown, and the item is placed in the Inbox folder in Messaging. Messages received through Bluetooth connectivity are indicated by

. See ‘Inbox—receive messages’, p. 87.

Remote SIM mode

To use the remote SIM mode with a compatible car kit enhancement, set Bluetooth connectivity on, and enable the use of the remote SIM mode with your device. See ‘Settings’, p. 28. Before the mode can be activated, the two devices must be paired and the pairing initiated from the other device. When pairing, use a 16-digit passcode, and set the other device as authorized. See ‘Pair devices’, p. 29. Activate the remote SIM mode from the other device.

When remote SIM mode is on in your device, Remote SIM is displayed in the standby mode. The connection to the wireless network is turned off, as indicated by in the signal strength indicator area, and you cannot use SIM card services or features requiring cellular network coverage.

When the wireless device is in the remote SIM mode, you

Draft

can only use a compatible connected enhancement, such as a car kit, to make or receive calls. Your wireless device will not make any calls, except to the emergency numbers programmed into your device, while in this mode. To make calls from your device, you must first leave the remote SIM mode. If the device has been locked, enter the lock code to unlock it first.

To leave the remote SIM mode, press the power key, and select Exit remote SIM mode.

Infrared connection

With infrared, you can transfer data such as business cards, calendar notes, and media files with a compatible device.

Do not point the infrared (IR) beam at anyone's eye or allow it to interfere with other IR devices. This device is a Class 1 laser product.

Send and receive data using infrared

1 Make sure that the infrared ports of the sending and

receiving devices are pointing at each other, and that there are no obstructions between the devices. The preferable distance between the two devices is up to 1 meter (3 feet).

2 The user of the receiving device activates the infrared

port. To activate the infrared port of your device to receive data through infrared, press , and select Tools >

Infrared.

3 The user of the sending device selects the desired

infrared function to start the data transfer. To send data through infrared, locate the desired file in an application or the file manager, and select

Options > Send > Via infrared.

If data transfer is not started within 1 minute after the activation of the infrared port, the connection is cancelled and must be started again.

Items received through infrared are placed in the Inbox folder in Messaging. New infrared messages are indicated by .

For infrared connection indicators, see ‘Essential indicators’, p. 27.

USB

Press , and select Tools > USB.

To have the device ask the purpose of the USB cable connection each time the cable is connected, select Ask on

connection > Yes.

Connections

If Ask on connection is set to off or you want to change

Draft

the mode during an active connection, select USB mode and from the following:

Media player—to synchronize music with Windows Media

Player. See ‘Music transfer with Windows Media Player’, p.

Connections

37.

PC Suite—to use Nokia PC applications such as Nokia PC

Suite, Nokia Lifeblog, and Nokia Software Updater

Data transfer— to transfer data between your device and

a compatible PC

Image print—to print images on a compatible printer. See

‘Image print’, p. 63.

PC connections

You can use your device with a variety of compatible PC connectivity and data communications applications. With Nokia PC Suite you can, for example, transfer images between your device and a compatible PC.

Always create the connection from the PC to synchronize with your device.

Synchronization

Sync enables you to synchronize your notes, calendar, text

messages, or contacts with various compatible applications on a compatible computer or on the internet.

You may receive synchronization settings in a special message. See ‘Data and settings’, p. 88.

In the Sync main view, you can see the different synchronization profiles. A synchronization profile contains the necessary settings to synchronize data in your device with a remote database on a server or compatible device.

1 Press , and select Tools > Sync. 2 Select a synchronization profile and Options >

Synchronize. To cancel synchronization before it

finishes, select Cancel.

Device manager

To connect to a server and receive configuration settings for your device, to create new server profiles, or to view and manage existing server profiles, press , and select

Tools > Device mgr..

You may receive server profiles and different configuration settings from your service providers and company information management department. These configuration

settings may include connection and other settings used

Draft

by different applications in your device.

Scroll to a server profile, and select Options and from the following:

Start configuration—to connect to the server and receive

configuration settings for your device

New server profile—to create a server profile

To delete a server profile, scroll to it, and press .

Modem

Press , and select Tools > Modem. To connect your device to a compatible PC through infrared to use it as a modem, press . For how to connect the devices, see ‘Infrared connection’, p. 31

Connections

Media applications

Draft

Music player

Music player supports files formats such as AAC, AAC+,

eAAC+, MP3, and WMA. Music player does not necessarily support all features of a file format or all the variations of file formats.

Media applications

Warning: Listen to music at a moderate level.

Continuous exposure to high volume may damage your hearing. Do not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely loud.

For how to add songs to your device, see ‘Transfer music’, p. 36.

For more information about copyright protection, see ‘Digital rights management’, p. 110.

Play a song

Tip! To open the music player, press and hold . You

can also open the player from the multimedia menu. See ‘Multimedia menu’, p. 14

1 Press , and select Music.

2 Open the media keys under

the 2-way slide.

3 Select a song, artist, or

other category.

4 To play the selected song or

list of songs, press .

To pause playback, press , and to resume, press again. To stop playback, press .

To fast forward or rewind, press and hold or .

To go to the next song, press . To return to the beginning of the song, press . To skip to the previous song, press again within 2 seconds after a song has started.

You can also use the scroll key to control the player.

To switch random play ( ) on or off, select Options >

Shuffle.

To repeat the current song ( ), all songs ( ), or to

Draft

switch repeat off, select Options > Repeat.

To adjust the volume, use the volume key.

To modify the tone of the music playback, select Options >

Equalizer.

To modify the balance and stereo image or to enhance bass, select Options > Audio settings.

To view a visualization during playback, select Options >

Start visualization.

To return to the standby mode and leave the player playing in the background, press , or to switch to another open application, press and hold .

Music menu

To select more music to play in Now playing view, select

Options > Go to Music menu.

The music menu shows the music available in the device and compatible memory card (if inserted). All songs lists all music. To view sorted songs, select Albums, Artists,

Genres, or Composers. To view playlists, select Playlists.

To refresh the library after you have updated the song selection in your device, select Options > Refresh Music

library.

To open the view that displays the currently playing song, press and hold .

Playlists

To view and manage playlists, in the music menu, select

Playlists. The following playlists appear automatically: Most played tracks, Recent tracks, and Recent additions.

To view details of the playlist, select Options > Playlist

details.

Create a playlist

1 Select Options > Create playlist. 2 Enter a name for the playlist, and select OK. 3 Select artists to find the songs you want to include in

the playlist. Press to add items. To show the song list under an artist title, press . To hide the song list, press .

4 When you have made your selections, select Done. If a

compatible memory card is inserted, the playlist is saved to the memory card.

To add more songs later, when viewing the playlist, select

Options > Add songs.

To add songs, albums, artists, genres, and composers to a playlist from the different views of the music menu, select an item and Options > Add to a playlist > Saved playlist or New playlist.

Media applications

To remov e a son g fro m a pla ylis t, sel ect Options > Remove

Draft

from playlist. This deletion does not delete the song from

the device; it only removes it from the playlist.

To reorder songs in a playlist, scroll to the song you want to move, and select Options > Reorder list. To grab songs and drop them to a new position, use the scroll key.

Music shop

Media applications

In the music shop (network service) you can search, browse, and purchase music for downloading to your device. The variety, availability, and appearance of music shop services may vary.

You must have music shop settings and valid internet connections in order to use this service. For more details, see ‘Music shop settings’, p. 36 and ‘Access points’, p.120.

Go to music shop

1 In the Music menu, select Options > Go to Music

shop.

2 Select from the displayed options to search, browse, or

select ringing tones.

Music shop settings

The availability and appearance of the music shop settings may vary. The settings may also be predefined and not editable.

If the settings are not predefined, you may be asked to enter the following settings:

Address—You must define the web address of the music

shop service.

Default acc. pt.—Select the access point to use when

connecting to the music shop.

User name—Enter your user name for the music shop.

Password—Enter your password for the music shop.

If User name and Password fields are left empty, you may have to enter them at login.

In the music shop, you may be able to edit the settings by selecting Options > Settings.

Transfer music

You can transfer music from a compatible PC or other compatible devices using a compatible USB cable or Bluetooth connectivity. For details, see ‘Bluetooth connectivity’, p. 27.

To refresh the library after you have updated the song selection in your device, in the Music menu, select

Options > Refresh Music library

The requirements of the PC for music transfer:

• Microsoft Windows XP operating system (or later)

• A compatible version of Windows Media Player

Draft

application. You can get more detailed information about Windows Media Player compatibility from the Nokia N95 section of the Nokia website.

• Nokia PC Suite 6.7 or later

Transfer music from PC

You can use three different methods to transfer music:

• To view your device on PC as an external hard drive

where you can transfer any data files, make the connection with a compatible USB cable or Bluetooth connectivity. If you are using the USB cable, select

Data transfer as the connection mode. A compatible

memory card needs to be inserted in the device.

• To synchronize music with Windows Media Player,

connect the compatible USB cable and select Media

player as the connection mode. A compatible memory

card needs to be inserted in the device.

• To use Nokia Music Manager in Nokia PC Suite, connect

the compatible USB cable and select PC Suite as the connection mode.

To change the default USB connection mode, press , select Tools > USB > USB mode.

Both Windows Media Player and Nokia Music Manager in Nokia PC Suite have been optimized for transferring music files. For information about transferring music with Nokia Music Manager, see the Nokia PC Suite user guide.

Music transfer with Windows Media Player

The functionality of the music synchronization may vary between different versions of the Windows Media Player application. For more information, see the corresponding Windows Media Player guides and helps.

Manual synchronization

After connecting your device with a compatible PC, Windows Media Player selects manual synchronization if there is not enough free memory in your device. With manual synchronization, you can select the songs and playlists that you want to move, copy, or remove.

The first time you connect your device you must enter a name that is used as the name of your device in Windows Media Player.

To transfer manual selections:

1 After your device is connected with Windows Media

Player, select your device in the navigation pane, if more than one device is connected.

2 Drag the songs or albums to the list pane for

synchronization. To remove songs or albums, select an item in the list, and click Remove from list.

3 Check that the list pane contains the files you want to

synchronize and that there is enough free memory on the device. Click Start Sync. to start the synchronization.

Media applications

Automatic synchronization

Draft

To change the default file transfer option in Windows Media Player, click the arrow under Sync, select your device, and click Set up Sync. Clear o r selec t th e Sync this device automatically check box.

If the Sync this device automatically check box is selected and you connect your device, the music library in your device is automatically updated based on playlists you

Media applications

have selected in Windows Media Player.

If no playlists have been selected, the whole PC music library is selected for synchronization. Note that your PC library may contain more files that can fit to the device memory and the compatible memory card of your device. See the Windows Media Player help for more information.

The playlists on your device are not synchronized with the Windows Media Player playlists.

Radio

Press , and select Applications > Radio. You can listen to the FM radio while using other applications.

You can make a call or answer an incoming call while listening to the radio. The radio is muted when there is an active call.

Listen to the radio

Note that the quality of the radio broadcast depends on the coverage of the radio station in that particular area.

The FM radio depends on an antenna other than the wireless device antenna. A compatible headset or enhancement needs to be attached to the device for the FM radio to function properly.

Press , and select Applications > Radio. To start a station search, select or , or press and hold the media keys or . To change the frequency manually, select Options > Manual tuning.

If you have previously saved radio stations, to go to the next or previous saved station, select or , or press the media keys or .

To adjust the volume, press the volume keys.

To listen to the radio using the loudspeaker, select

Options > Activate loudspeaker.

Warning: Listen to music at a moderate level.

Continuous exposure to high volume may damage your hearing. Do not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely loud.

To save the current tuned station to your station list, select

Draft

Options > Save station. To open the list of your saved

stations, select Options > Stations.

To return to the standby mode and leave the FM radio playing in the background, select Options > Play in

background.

Your device may have predefined services. To connect to the internet to browse available services that you can add to Video center, select Add new services.

Service providers may provide free content or charge a fee. Check the pricing in the service or from the service provider.

Saved stations

To open the list of your saved stations, select Options >

Stations.

To listen to a saved station, select Options > Station >

Listen.

To change station details, select Options > Station > Edit.

Tip! You can add shortcuts to saved stations in the multimedia menu. See ‘Multimedia menu’, p. 14.

Video center

With Video center (network service), you can download and stream video clips over the air from compatible internet video services using packet data or WLAN. You can also transfer video clips from a compatible PC to your device, and view them in Video center.

Video center supports the same file formats as RealPlayer.

See ‘RealPlayer’, p. 41.

Find and view videos

1 Press , and select Applications > Video center. 2 To connect to a service, select the desired video service. 3 The device updates and displays the content available

in the service. To view videos by categories (if available), press and to scroll the other tabs.

4 To view information about a video, select Options >

Video details.

Some clips can be streamed over the air, but others must be first downloaded to your device. To download, select Options > Download. To stream a clip or view a downloaded clip, select

Options > Play.

5 When the clip is playing, use the media keys to control

the player. To adjust the volume, use the volume key. To view the video in full screen, pause or stop the video, and select Options > Resume in full screen or Play in

full screen.

Media applications

Downloads continue in the background if you exit the

Draft

application. The downloaded videos are saved in Video

center > My videos.

To connect to the internet to browse available services that you can add to the main view, select Add new services.

Internet videos

Internet videos are video clips distributed in the internet

Media applications

using RSS-based feeds. You can add new feeds to Internet

videos in the settings. See ‘Settings’, p. 40.

1 In Video center, select the Internet videos folder. Your

feeds are displayed. To add or delete feeds, select Options > Feed

subscriptions.

2 To view the videos available in a feed, scroll to it, and

press . To view information about a video, select

Options > Video details.

3 To download a video, scroll to it, and select Options >

Download. To play the downloaded video, press .

In order for the video clips to be available in Video center, you must save them in the location C:\Data\My Videos in the device memory (C:\) or E:\My Videos in a compatible memory card (E:\). Use, for example, File manager available in Nokia PC Suite to transfer files to the correct location.

When the clip is playing, use the media keys to control the player. To adjust the volume, use the volume key. To view the video in full screen, pause or stop the video, and select

Options > Resume in full screen or Play in full screen.

If there is not enough free space in the device memory and compatible memory card, the application automatically deletes some of the oldest watched videos when new videos are downloaded. indicates videos that may soon be deleted. To prevent a video from being automatically deleted ( ), select Options > Protect.

To delete a video, select Options > Delete. To cancel an ongoing download, select Options > Cancel download. To change the folder or memory location of a video, select

Options > Organize and the desired option.

Play downloaded videos

The downloaded and downloading videos are saved in

Video center > My videos. To play a downloaded video,

press .

You can also transfer video clips from a compatible PC to your device, and view them in Video center > My videos.

Settings

Define the services

1 In Video center, select Options > Settings > Video

service selection.

2 To select video services, select Video on demand. To

Draft

add or delete internet video feeds, select Internet

videos.

3 Select the services you want to appear in the

application. To add a new internet video feed that is not displayed in the list, select Options > Add feed. Enter the name and address of the service received from the service provider. Some services require a user name and a password that you receive from the service provider.

To define the other settings, select Options > Settings and from the following:

Default access points—Select the access points used for

the data connection. Using packet data access points to download files may involve transmission of large amounts of data through your service provider's network. Contact your service provider for information about data transmission charges.

Preferred memory—Select whether downloaded videos

are saved in the device memory or a compatible memory card. If the selected memory becomes full, the device saves the content in the other memory, if available. If there is not enough space in the other memory, the application automatically deletes some of the oldest watched videos.

Thumbnails—Select whether to view thumbnail images in

the video lists of video services.

RealPlayer

Press , and select Applications > RealPlayer. With

RealPlayer, you can play video clips, or stream media files

over the air without saving them to the device first.

RealPlayer supports files with extensions such as .3gp,

.mp4 or .rm. However, RealPlayer does not necessarily support all file formats or all the variations of file formats.

In landscape view, use the media keys to control the player.

Play video clips

1 To play a saved media file, select Options > Open and

from the following:

Most recent clips—to play one of the last six files

played in RealPlayer

Saved clip—to play a file saved in Gallery.

2 Scroll to a file, and press to play the file.

To adjust the volume, use the volume key.

Media applications

Stream content over the air

Draft

Many service providers require you to use an internet access point (IAP) for your default access point. Other service providers allow you to use a WAP access point.

In RealPlayer, you can only open an rtsp:// URL address. However, RealPlayer recognizes an http link to a .ram file.

To stream content over the air, select a streaming link saved in Gallery, on a web page, or received in a text

Media applications

message or multimedia message. Before live content begins streaming, your device connects to the site and starts loading the content. The content is not saved in your device.

RealPlayer settings

You may receive RealPlayer settings in a special message from the service provider. See ‘Data and settings’, p. 88. For more information, contact your service provider.

Select Options > Settings and from the following:

Video—to adjust the contrast of the video or have RealPlayer automatically repeat video clips after they

finish playing

Streaming—to select whether to use a proxy server,

change the default access point, and set the port range

used when connecting. Contact your service provider for the correct settings.

Adobe Flash Player

To view, play, and interact with compatible flash files made for mobile devices, press , and select Applications >

Flash Player. Scroll to a flash file, and press .

Nokia Lifeblog

To start Lifeblog on your device, press , and select

Applications > Lifeblog.

Nokia Lifeblog is a combination of software for mobile phone and PC that keeps a multimedia diary of the items that you collect with your device. Nokia Lifeblog automatically keeps track of your multimedia items and organizes your photos, videos, sounds, text messages, multimedia messages, and weblog posts into a chronology that you can browse, search, share, publish, and back up.

For more information on weblog services and their compatibility with Nokia Lifeblog, visit www.nokia.com/ lifeblog, or press F1 in the Nokia Lifeblog PC application to open Nokia Lifeblog Help.

Installation on your PC

Draft

Before you install Nokia Lifeblog on a compatible PC, you need the following:

• 1 GHz Intel Pentium or equivalent, 128 MB RAM

• 400 MB of available hard disk space (if Microsoft

DirectX and Nokia PC Suite must be installed)

• Graphics capability of 1024x768 and 24-bit color

• 32 MB graphics card

• Microsoft Windows 2000 or Windows XP

To install Nokia Lifeblog on your PC:

1 Insert the CD-ROM or DVD-ROM supplied with your

device.

2 Install Nokia PC Suite (includes Nokia Connectivity

Cable drivers for USB connection).

3 Install Nokia Lifeblog for PC.

If Microsoft DirectX 9.0 is not already installed on your PC, it is installed at the same time with Nokia Lifeblog for PC.

Connect your device and your PC

To connect your device and a compatible PC using a USB data cable:

1 Ensure that you have installed Nokia PC Suite. 2 Connect the USB data cable to the device and the PC.

The USB mode should be PC Suite, see ‘USB’, p. 31. When you connect your device to the PC for the first

time after you have installed Nokia PC Suite, the PC installs the specific driver for your device. This may take a while.

3 Start the Nokia Lifeblog PC application.

To connect your device and a compatible PC using Bluetooth wireless technology:

1 Ensure that you have installed Nokia PC Suite on your

PC.

2 Ensure that you have paired your device and the PC

through Bluetooth wireless technology with Get Connected in Nokia PC Suite.

3 Activate Bluetooth connectivity on your device and on

your PC. For details, see ‘Bluetooth connectivity’, p. 27 and the documentation for your PC.

Copy items

To copy new or edited items from your device to your PC, and copy the selected items from your PC to your device:

1 Connect your device to the PC. 2 Start the Nokia Lifeblog application on your PC. 3 In the Nokia Lifeblog PC application, select File > Copy

from Phone and to Phone.

The new items from your device are copied to your PC. The items on the To Phone view on your PC are copied to your device.

Media applications

Browse Timeline and Favorites

Draft

When you start Nokia Lifeblog on your device, the Timeline view opens and shows your multimedia items. To open your saved favorites, select Options > View Favorites.

When you start Nokia Lifeblog on your PC, you have several ways to move around in the Timeline and Favorites views. The fastest way is to grab the slider handle and move it forward or backward, fast or slow. Alternatively, click the

Media applications

time bar to select a date, use the Go to date feature, or use the arrow keys.

Post to the web

To share your best N okia Lifeblog items, se nd them to your weblog on the internet for others to see.

You must first create an account with a weblog service, create one or more weblogs that you use as the destination of your posts, and add the weblog account to Nokia Lifeblog. The recommended weblog service for Nokia Lifeblog is TypePad from Six Apart, www.typepad.com

On your device, to add the weblog account in Nokia Lifeblog, select Options > Settings > Blog. On your PC, edit accounts in the Blog account manager window.

To post items to the web from your device:

1 In Timeline or Favorites, select the items that you

want to post to the web.

2 Select Options > Post to Web. 3 If you use the feature for the first time, Nokia Lifeblog

retrieves a weblog list from the weblog server.

4 The weblog post dialog opens. Select the weblog you

want to use from the Post to: list. If you have created new weblogs, to update the weblog list, select

Options > Refresh blog list.

5 Enter a title and a caption for the post. You can also

write a longer story or description in the body text field.

6 When everything is ready, select Options > Send.

To post items to the web from your PC:

1 In the timeline of favorites, select the items (a

maximum of 50) that you want to post to the web.

2 Select File > Post to the Web....

3 Enter a title and a caption for the post. You can also

write a longer story or description in the body text field.

4 Select the weblog that you want to use from the Post

to: list.

5 When everything is ready, click the Send button.

Import items from other sources

In addition to the .jpeg images of your device, you can also import .jpeg images and .3gp and .mp4 video clips, .amr sound files, and .txt text files from other sources (such as a CD, DVD, or folders on your hard disk) into Nokia Lifeblog.

To import images or videos from a compatible PC to Nokia

Draft

Lifeblog for PC, in the timeline or favorites, select File >

Import from PC....

Media applications

Camera

Draft

Your Nokia N95 has two cameras, a high resolution camera

Camera

on the back of the device (the main camera in landscape mode) and a lower resolution camera on the front (the secondary camera in portrait mode). You can use both cameras to take still pictures and record videos.

Your device supports an image capture resolution of 2592x1944 pixels using the main camera. The image resolution in this guide may appear different.

The images and video clips are automatically saved in the

Images & video folder in Gallery. The cameras produce

.jpeg images. Video clips are recorded in the MPEG-4 file format with the .mp4 file extension, or in the 3GPP file format with the .3gp file extension (sharing quality). See ‘Video settings’, p. 53.

Tip! To enter Gallery and view the pictures you have

taken, press the review key on the side of your device twice.

You can send images and video clips in a multimedia message, as an e-mail attachment, or by using Bluetooth connectivity, infrared, or WLAN connection. You can also upload them to a compatible online album. See ‘Online sharing’, p. 65.

Take pictures

When taking a picture, note the following:

• Use both hands to keep the camera still.

• The quality of a digitally zoomed picture is lower than

that of a nonzoomed picture.

• The camera goes into the battery saving mode if there

are no keypresses for a moment. To continue taking pictures, press .

To take a picture, do the following:

1 To activate the main

camera, press and hold the capture key. If the camera is in Video mode, select

Image mode from the

active toolbar.

2 To lock the focus on an

object, press the capture key halfway down (main camera only, not available in close-up and landscape scenes). The green locked focus indicator appears on the display. If the focus was not locked, the red focus indicator appears. Release the

capture key, and press it halfway down again. You can,

Draft

however, take the picture without locking the focus.

3 To take a picture, in the main camera, press the capture

key. Do not move the device before the image is saved.

To zoom in or out, use the zoom key in your device.

To make lighting and color adjustments before taking a picture, use the scroll key to scroll through the active toolbar. See ‘Setup settings—adjust color and lighting’, p. 50. Saving the captured image may take longer if you change the zoom, lighting, or color settings.

To free memory before taking a picture, select Options >

Go to free memory (only available if you have backed up

images or video clips). See ‘Free memory’, p. 58.

To activate the front camera, select Options > Use

secondary camera.

To leave the camera open in the background, and use other applications, press . To return to the camera, press the capture key.

To close the main camera, select Exit.

Still image camera indicators

The still image camera viewfinder displays the following:

1 The current capture mode indicator. 2 The active toolbar, which you can scroll through before

capturing the image to select different items and

settings (the active toolbar is not displayed during focus and image capture). See ‘Active toolbar’, p. 47.

3 The image

resolution indicator indicates whether the quality of the image is Print

5M - Large, Print 3M Medium, Print 2M Medium, E-mail 0.8M - Med., or MMS 0.3M - Small.

4 The image counter displays the estimated number of

images you can capture using the current image quality setting and memory in use (the counter is not displayed during focus and image capture).

5 The device memory ( ) and memory card ( )

indicators show where images are saved.

Active toolbar

Active toolbar provides you with shortcuts to different items and settings before and after taking a picture or recording a video. Scroll to items, and select them by pressing the scroll key. You can also define when the active toolbar is visible on the display.

Camera

If you want the active toolbar to be visible before and after

Draft

taking a picture or recording a video, select Options >

Show icons. To view the active toolbar only when you need

it, select Options > Hide icons. Only the capture mode

Camera

indicator is shown on the display. To activate the active toolbar, press the scroll key. To hide it again, press the capture key half way down.

Before taking a picture or recording a video, in the active toolbar, select from the following:

to switch between the video and image modes

to select the scene

to select the flash mode (images only)

to activate the self-timer (images only). See ‘You in the

picture—self-timer’, p. 51.

to activate the sequence mode (images only). See ‘Take

pictures in a sequence’, p. 51.

to select a color effect

to adjust white balance

to adjust the exposure compensation (images only)

to adjust light sensitivity (images only)

to adjust contrast (images only)

to adjust sharpness (images only)

The icons change to reflect the current status of the setting.

The available options vary depending on the capture mode and view you are in.

See also active toolbar options in ‘After taking a picture’, p. 48, ‘After recording a video’, p. 53, and ‘Active toolbar’, p. 56 in Gallery.

After taking a picture

After you take the picture, select the following from the active toolbar (available only if Show captured image is set to Yes in still image camera settings):

• If you do not want to keep the image, select Delete.

• To send the image using multimedia, e-mail, Bluetooth

connectivity, infrared, or upload it to a compatible online album, press the call key, or select Send. For more information, see ‘Messaging’, p. 85, ‘Bluetooth connectivity’, p. 27, and ‘Online sharing’, p. 65. This option is not available during an active call. You can also send the image to a call recipient during an active call. Select Send to caller (only available during an active call).

• To tag images to the Print Basket for later printing,

select Add to Print Basket.

• To print the picture, select Print. See ‘Image print’,

p. 63.

• To return to the viewfinder to capture a new image,

Draft

press the capture key.

To use the picture as wallpaper in the active standby, select

Options > Set as wallpaper.

To set the image as a call image for a contact, select Set

as contact call img..

Still image camera settings

There are two kinds of settings for the still image camera: Image setup and main settings. To adjust Image setup, see ‘Setup settings—adjust color and lighting’, p. 50. The setup settings return to the default settings after you close the camera, but the main settings remain the same until you change them again. To change the main settings, select

Options > Settings and from the following:

Image quality—Print 5M - Large (2592x1944 resolution), Print 3M - Medium (2048x1536 resolution), Print 2M Medium (1600 x 1200), E-mail 0.8M - Med. (1024x768

resolution), or MMS 0.3M - Small (640x480 resolution). The better the image quality, the more memory the image consumes. If you want to print the image, select Print 5M

- Large, Print 3M - Medium, or Print 2M - Medium. If

you want to send it through e-mail, select E-mail 0.8M -

Med.. To send the image through MMS, select MMS 0.3M

- Small.

These resolutions are only available in the main camera.

Add to album—Select whether you want to save the image

to a certain album in the gallery. If you select Yes, a list of available albums opens.

Show captured image—Select Yes if you want to see the

captured image after it is taken, or No if you want to continue taking pictures immediately.

Default image name—Define the default name for the

captured images.

Extended digital zoom (main camera only)—Select On to

allow the zoom increments to be smooth and continuous between digital and extended digital zoom. If you want to limit the zoom to where the selected image quality is maintained, select Off.

Capture tone—Select the tone you want to hear when you

take a picture.

Memory in use—Select where to store your images.

Rotate image - Select whether you want the image to be

rotated the right way up when you open it in the gallery.

Restore camera settings—Select Yes to return the default

values to the camera settings.

Flash

The flash is available only in the main camera.

Camera

Keep a safe distance when using the flash. Do not use the

Draft

flash on people or animals at close range. Do not cover the flash while taking a picture.

Camera

The camera has an LED flash for low light conditions. The following flash modes are available for the still image camera: Automatic (), R. eye redu. (), On (), and

Off ().

To change the flash mode, in the active toolbar, select the desired flash mode.

Setup settings—adjust color and lighting

To enable the camera to reproduce colors and lighting more accurately, or to add effects to your pictures or videos, use the scroll key to scroll through the active toolbar, and select from the following options:

White balance—Select the current lighting condition from

the list. This allows the camera to reproduce colors more accurately.

Exposure compensation (images only)—Adjust the

exposure time of the camera.

Flash—Select the desired flash mode. See ‘Flash’, p. 49.

Color tone—Select a color effect from the list.

Light sensitivity (images only)—Select the light sensitivity

of the camera. The darker the environment, the higher the light sensitivity should be.

The screen display changes to match any settings you make, so that you see how the change affects the pictures or videos.

The available settings vary depending on the selected camera.

The setup settings are camera specific; if you change the settings in the secondary camera, the settings in the main camera do not change. The setup settings do, however, transfer between the image and video modes. The setup settings return to the default settings when you close the camera.

If you select a new scene, the color and lighting settings are replaced by the selected scene. See ‘Scenes’, p. 50. You can change the setup settings after selecting a scene if needed.

Scenes

A scene helps you to find the right color and lighting settings for the current environment. The settings of each scene have been set according to a certain style or environment.

Scenes are only available in the main camera.

In the active toolbar, select from the following options:

Draft

Video scenes

Automatic ( )(default) and Night ()

Image scenes

Auto () (default), User defined (), Close-up mode(), Portrait (), Landscape (), Sports (), Night (), and Night portrait ().

When you take pictures, the default scene is Auto. You can select the User defined scene as the default scene.

To make your own scene suitable for a certain environment, scroll to User defined, and select Options >

Change. In the user defined scene you can adjust different

lighting and color settings. To copy the settings of another scene, select Based on scene mode and the desired scene.

Take pictures in a sequence

The sequence mode is available only in the main camera.

To set the camera to take six pictures or more in a sequence (if enough memory available), in the active toolbar, select Switch to sequence mode > Burst to take six pictures, or the time period for taking pictures. The number of pictures taken depends on the available memory.

To take six pictures, press the capture key. To stop taking pictures, press Cancel. To take more than six pictures, press and hold the capture key. To stop taking pictures, release the capture key. You can capture up to 100 images, depending on the available memory.

To use a time period for taking pictures, select Switch to

sequence mode, and a time preriod. To start taking

pictures, press the capture key. To stop taking pictures before the time ends, press the capture key again.

After you take the pictures, they are shown in a grid on the display. To view a picture, press to open it. If you used a time period for taking pictures, the last taken picture is shown on the display. To view other pictures, press .

You can also use the sequence mode with the self-timer. When using the self-timer, the maximum amount of pictures is six pictures.

To return to the sequence mode viewfinder, press the capture key.

You in the picture—self-timer

The self-timer is available only in the main camera.

Use the self-timer to delay the capture so that you can include yourself in the picture. To set the self-timer delay, in the active toolbar, select Self timer > 2 seconds, 10

seconds, or 20 seconds. To activate the self-timer, select

Camera

Activate. The self-timer indicator ( ) blinks and the

Draft

device beeps when the timer is running. The camera takes the picture after the selected delay elapses.

Camera

To switch off Self timer, in the active toolbar, select Self

timer > Off.

Tip! In the active toolbar, select Self timer > 2

seconds to keep your hand steady when taking a

picture.

Record videos

1 To activate the main camera, press and hold the

capture key. If the camera is in the Image mode, select

Switch to video mode from the active toolbar.

2 Press the capture key to start recording. In the portrait

mode, use the scroll key for recording. The red record icon is shown and a tone sounds, indicating that recording has started.

3 Select Stop to stop recording. The video clip is

automatically saved to the Images & video folder of

Gallery. See ‘Gallery’, p. 55. The maximum length of the

video is 60 minutes (if enough memory available).

To pause recording at any time, press Pause. The pause icon ( ) blinks on the display. Video recording automatically stops if recording is set to pause and there

are no keypresses within a minute. Press Continue to resume recording.

To zoom in or out of the subject, press the zoom key on the side of the device.

To make lighting and color adjustments before recording a video, use the scroll key to scroll through the active toolbar. See ‘Setup settings—adjust color and lighting’, p. 50 and ‘Scenes’, p. 50.

To free memory before recording a video, select Options >

Go to free memory (only available if you have backed up

images or video clips). See ‘Free memory’, p. 58.

To activate the front camera, select Options > Use

secondary camera.

Video capture indicators

The video viewfinder displays the following:

1 The current capture mode indicator. 2 The audio mute on indicator. 3 The active toolbar, which you can scroll through before

recording to select different items and settings (the toolbar is not displayed during recording). See ‘Active toolbar’, p. 47.

4 The total available video recording time. When you are

recording, the current video length indicator also shows the elapsed time and time remaining.

5 The device

Draft

memory ( ) and memory card ( ) indicators show where videos are saved.

6 The video

quality indicator indicates whether the quality of the video is TV High

quality, TV normal quality, E-mail high quality, Email norm. quality, or Sharing quality.

7 The video clip file type. 8 The video stabilization is turned on ( ). See ‘Video

settings’, p. 53.

To display all viewfinder indicators, select Options > Show

icons. Select Hide icons to display only the video status

indicators, and during the recording, the available record time, zoom bar when zooming, and the selection keys.

After recording a video

After you record a video clip, select the following from the active toolbar (available only if Show captured video is set to Yes in Video settings):

• To immediately play the video clip you just recorded,

select Play.

• If you do not want to keep the video, select Delete.

• To send the video clip using multimedia, e-mail,

Bluetooth connectivity, or infrared, or upload it to a compatible online album, press the call key, or select

Send. For more information, see ‘Messaging’, p. 85,

‘Bluetooth connectivity’, p. 27, and ‘Online sharing’, p. 65. This option is not available during an active call. You may not be able to send video clips saved in the .mp4 file format in a multimedia message. You can also send the video clip to a call recipient during an active call. Select Send to caller.

• To return to the viewfinder to record a new video clip,

press the capture key.

Video settings

There are two kinds of settings for the video recorder: Video setup and main settings. To adjust Video setup settings, see ‘Setup settings—adjust color and lighting’, p. 50. The setup settings return to the default settings after you close the camera, but the main settings remain the same until you change them again. To change the main settings, select Options > Settings and from the following:

Video quality—Set the quality of the video clip to TV High quality, TV normal quality, E-mail high quality, E-mail

Camera

norm. quality (standard quality for playback through your

Draft

handset), or Sharing quality. If you want to view the video on a compatible TV or PC, select TV High quality or TV

normal quality, which have VGA resolution (640x480) and

Camera

the .mp4 file format. You may not be able to send video clips saved in the .mp4 file format in a multimedia message. To send the video clip through MMS, select

Sharing quality (QCIF resolution, .3gp file format). The size

of the video clip recorded with Sharing quality is limited to 300 KB (about 20 seconds in duration) so that it can be conveniently sent as a multimedia message to a compatible device.

Video stabilization—Select On to reduce camera shaking

when recording the video.

Audio recording—Select Mute if you do not want to

record sound.

Add to album—Select whether you want to add the

recorded video clip to a certain album in Gallery. Select

Yes to open a list of available albums.

Show captured video—Select whether you want the first

frame of the recorded video clip to be shown on the display after the recording stops. Select Play from the active toolbar (main camera) or Options > Play (secondary camera) to view the video clip.

Default video name—Define the default name for the

captured video clips.

Memory in use—Define the default memory store: device

memory or memory card (if inserted).

Restore camera settings—Select Yes to return the default

values to the camera settings.

Gallery

Draft

To store and organize your images, video clips, sound clips, and streaming links, or share your files with other compatible Universal Plug and Play (UPnP) devices through WLAN, press , and select Gallery.

Tip! If you are in another application, to view the last saved picture in Gallery, press the review key on the side of your device. To enter the Images & video folder main view, press the review key again.

View and browse files

Select Images & video

, Tracks , Sound

clips , Streaming links

, Presentations ,

All files , or Home network , and press

to open it. The content

in the Images & video folder is shown in the landscape mode.

You can browse and open folders; and mark, copy, and move items to folders.

You can also create albums; and mark, copy, and add items to albums. See ‘Albums’, p. 57.

Files stored on your compatible memory card (if inserted) are indicated with .

To open a file, press . Video clips, .ram files, and streaming links are opened and played in RealPlayer, and music and sound clips in Music. See ‘RealPlayer’, p. 41, and ‘Music player’, p. 34.

To copy or move files to the memory card (if inserted) or to device memory, select a file and Options > Move and

copy > Copy to memory card or Move to memory card,

or Copy to phone mem. or Move to phone mem..

To download sound clips into Gallery using the browser, in the Sound clips folders, select Downld. sounds.

Images and video clips

Pictures taken and video clips recorded with the camera are stored in the Images & video folder in Gallery. Images and video clips can also be sent to you in a multimedia message, as an e-mail attachment, or through Bluetooth connectivity or infrared. To be able to view a received image or video clip in Gallery or in the media player, you

Gallery

must save it in the device memory or on a compatible

Draft

memory card (if inserted).

The video clips saved in Video center are not shown in

Gallery

Images & video in Gallery. To view video clips in Video center, see ‘Video center’, p. 39.

Select Gallery >

Images & video.

The images and video clip files are in a loop, and ordered by date and time. The number of files is displayed. To browse the files one by one, press

or . To browse files in groups, press or .

When the image is opened, to zoom in an image, press the zoom key on the side of your device. The zooming ratio is not stored permanently.

To rotate the selected image left or right, select Options >

Rotate > Left or Right.

To edit a video clip or a photo, select Options > Edit. An image editor or a video editor opens. See ‘Edit video clips’, p. 59. See ‘Edit images’, p. 58.

To create custom video clips, select a video clip or several clips in the gallery, and select Options > Edit. See ‘Edit video clips’, p. 59.

To print your images on a compatible printer, or to store them on a compatible memory card (if inserted) for printing, select Options > Print. See ‘Image print’, p. 63. You can also tag images for later printing to the Print Basket in Gallery. See ‘Print Basket’, p. 57.

To add an image or a video clip to an album in the gallery, select Options > Albums > Add to album. See ‘Albums’, p. 57.

To use the picture as a background image, select the picture and Options >Use image > Set as wallpaper.

To delete an image or video clip, from the active toolbar, select Delete. See ‘Active toolbar’, p. 56.

To switch from Gallery to the camera, press and hold the capture key.

Active toolbar

In the Images & video folder, you can use active toolbar as a shortcut to select different tasks. The active toolbar is available only when you have selected an image or a video clip.

In the active toolbar, scroll up or down to different items, and select them by pressing the scroll key. The available

options vary depending on the view you are in and whether

Draft

you have selected an image or a video clip. You can also define whether the active toolbar is always visible on the display or activated by a keypress.

If you want the active toolbar to be visible on the display, select Options > Show icons.

If you want the active toolbar to be visible only when you need it, select Options > Hide icons. To activate the active toolbar, press .

Select from the following:

to play the selected video clip

to send the selected image or video clip

/ to add or remove an image from the Print Basket.

See ‘Print Basket’, p. 57.

to view the images in the Print basket

to start a slide show of your images

to delete the selected image or video clip

to print the viewed image

to reduce the resolution of the selected image to free

memory for new images. See ‘Free memory’, p. 58.

The available options may vary depending on the view you are in.

Print Basket

You can tag images to the Print Basket, and print them later with a compatible printer or in a compatible printing kiosk, if available. See ‘Image print’, p. 63. The tagged images are indicated with in the Images & video folder and albums.

To tag an image for later printing, select an image, and

Add to Print Basket from the active toolbar.

To view the images in the Print Basket, select View Print

Basket from the active toolbar, or select from the Images & video folder (available only when you have

added pictures to the Print Basket).

To remove an imag e from the Print Basket, select an image in the Images & video folder or in an album, and Remove

from print from the active toolbar.

Albums

With albums you can conveniently manage your images and video clips. To view the albums list, select Images &

video > Options > Albums > View albums.

To add a picture or a video clip to an album in the gallery, scroll to a picture or video clip, and select Options >

Albums > Add to album. A list of albums opens. Select the

album to which you want to add the picture or video clip.

Gallery

The added pictures and video clips are not deleted from the

Draft

Images & video folder.

To remove a file from an album, press . The file is not

Gallery

deleted from the Images & video folder in Gallery.

To create a new album, in the albums list view, select

Options > New album.

Your device starts a device search. Select a device, and a folder to which you want to transfer the media files. Select

OK.

To change the storage device or folder settings, select

Options > Transfer > Settings > Storage device or Storage folder.

Free memory

To reduce the resolution and file size of images saved in

Gallery and free memory for new pictures, select Options > Shrink. To back up the images first, copy them

to a compatible PC or other location. Selecting Shrink reduces the resolution of an image to 640x480.

To increase free memory space after you have copied items to other locations or devices, select Options > Free

memory. You can browse a list of files you have copied. To

remove a copied file from Gallery, select Options > Delete.

Back-up files

To transfer and back-up media files from your device to a compatible PC through the WLAN, select Options >

Transfer > Start. See ‘Wireless LAN’, p. 25.

Edit images

To edit the pictures after taking them, or the ones already saved in Gallery, select Options > Edit.

Select Options > Apply effect to open a grid where you can select different edit options indicated by small icons. You can crop and rotate the image; adjust the brightness, color, contrast, and resolution; and add effects, text, clip art, or a frame to the picture.

Crop image

To crop an image, select Options > Apply effect > Crop. To crop the image size manually, select Manual or a predefined aspect ratio from the list. If you select Manual, a cross appears in the upper left corner of the image. Use the scroll key to select the area to crop, and select Set. Another cross appears in the lower right corner. Again select the area to be cropped. To adjust the first selected

area, select Back. The selected areas form a rectangle that

Draft

forms the cropped image.

If you selected a predefined aspect ratio, select the upper left corner of the area to be cropped. To resize the highlighted area, use the scroll key. To freeze the selected area, press . To move the area within the picture, use the scroll key. To select the area to be cropped, press .

Reduce redness

To reduce redness of the eyes in an image, select Options >

Apply effect > Red eye reduction. Move the cross onto

the eye, and press . A loop appears on the display. To resize the loop to fit the size of the eye, use the scroll key. To reduce the redness, press .

Useful shortcuts

Shortcuts in the image editor:

• To view an image in the full screen, press . To return

to the normal view, press again.

• To rotate an image clockwise or counterclockwise,

press or .

• To zoom in or out, press or .

• To move on a zoomed image, scroll up, down, left, or

right.

Edit video clips

To edit video clips in Gallery and create custom video clips, scroll to a video clip, and select Options >Edit. See ‘Gallery’, p. 55. To create custom video clips, combine and trim video clips, and add images, sound clips, transitions, and effects. Transitions are visual effects that you can add in the beginning and end of the video or between the video clips.

The video editor supports .3gp and .mp4 video file formats, and .aac, .amr, .mp3, and .wav audio file formats.

You can use Movie director to create custom video clips. Select the video clips and images you want to create a muvee with and select Options > Edit > Create muvee. See ‘Movie director’, p. 63.

In the video editor you can see two timelines: video clip timeline and sound clip timeline. The images, text, and transitions added to a video clip are shown on the video clip timeline. To switch between the timelines, scroll up or down.

Edit video, sound, image, text, and transitions

To create custom video clips, mark and select one or more video clips, and select Options > Edit > Video editor.

Gallery

To modify the video, select from the following options:

Draft

Edit video clip:

Cut—trims the video clip in the cut video clip view

Gallery

Add color effect—inserts a color effect on the video clip

Use slow motion—slows the speed of the video clip

Mute sound or Unmute sound—mutes or unmutes the

original video clip sound

Move—moves the video clip to the selected location

Remove—removes the video clip from the video

Duplicate—makes a copy of the selected video clip

Edit text (shown only if you added text)—to move, remove,

or duplicate text; change the color and style of the text; define how long it stays on the screen; and add effects to the text

Edit image (shown only if you added an image)—to move,

remove, or duplicate an image; define how long it stays on the screen; and set a background or a color effect to the image

Edit sound clip (shown only if you have added a sound

clip)—to cut or move the sound clip, to adjust its length, or to remove or duplicate the clip.

Edit transition—There are three types of transitions: at the

start of a video, at the end of a video, and transitions

between video clips. You can select start transition when the first transition of the video is active.

Insert—Select Video clip, Image, Text, Sound clip, or New sound clip.

Movie—Preview the movie in the full screen or as a

thumbnail, save the movie, or cut the movie to a proper size for sending it in a multimedia message.

To take a snapshot of a video clip, in the cut video view, select Options > Take snapshot. In the thumbnail preview view, press , and select Take snapshot.

To save your video, select Options > Movie > Save. To define the Memory in use, select Options > Settings. The default is the device memory.

In the Settings view, you can also define Default video

name, Default snapshot name, Resolution, and Memory in use.

Edit video clips to send

To send a video clip, select Options > Send > Via

multimedia, Via e-mail, Via Bluetooth, or Via infrared.

Contact your wireless service provider for details of the maximum multimedia message size that you can send.

If you want to send a video clip that is over the maximum multimedia message size allowed by your service provider, you can send the clip using Bluetooth wireless technology.

See ‘Send data using Bluetooth connectivity’, p. 29. You

Draft

can also transfer your videos to a compatible PC using Bluetooth connectivity, USB data cable, or by using a compatible memory card reader enhancement.

You can also cut the video clip for sending it in a multimedia message. In the video editor main view, select

Options > Movie > Edit for MMS. The duration and size

of the video clip is shown on the display. To edit the size of the clip, scroll left or right. When the clip is the proper size to send, select Options > Send via MMS.

If your video clip is in .mp4 format, you may not be able to send it in a multimedia message. To change the file format of the clip, scroll to it in Gallery, and select Options > Edit > Options > Settings > Resolution > MMS compatible. Return to the video editor main view, select Options >

Movie > Save, and enter a name for the clip. The video clip

is saved in .3gpp format and can be sent in a multimedia message. The file format of the original video clip does not change.

Continue—to resume the slide show, if paused

End—to close the slide show

To browse the images, press (previous) or (next) (available only when Zoom and pan is off).

To adjust the tempo of the slide show, before starting the slide show, select Options > Slide show > Settings >

Delay between slides.

To make the slide show move smoothly from one slide to another, and let the gallery randomly zoom in and out in the images, select Zoom and pan.

To add sound to the slide show, select Options > Slide

show > Settings and from the following:

Music—Select On or Off.

Track—Select a music file from the list.

To decrease or increase the volume, use the volume key in your device.

Gallery

Slide show

In the active toolbar, select Start slide show () to view a slide show of images in full screen. The slide show starts from the selected file. Select from the following:

Pause—to pause the slide show

TV out mode

To view the captured images and video clips on a compatible TV, use a Nokia Video Connectivity Cable.

Before viewing the images and video clips on TV, you must configure the TV out settings for the applicable TV system and TV aspect ratio. See ‘Enhancement’, p. 113.

To watch images and video clips on TV, do the following:

Draft

1 Connect a Nokia Video Connectivity Cable to the video

Gallery

input of a compatible TV.

2 Connect the other end of the Nokia Video Connectivity

Cable to the Nokia AV Connector of your device.

3 You may need

to select the cable mode.

4 Press , and

select

Gallery > Videos & images and

the file you want to view.

The images are shown in the image viewer, and the video clips are played in RealPlayer.

All audio, including the stereo video clip sound, ringing tone, and key tone, is routed to the TV when the Nokia Video Connectivity Cable is connected to the device. You can use the device microphone normally.

For all applications other than the Images & video folder in Gallery and RealPlayer, the TV screen displays what is displayed on the screen of your device.

The opened image is displayed in full screen on the TV. When you open an image in the thumbnail view while it is viewed on the TV, Zoom in is not available.

When you open a highlighted video clip, RealPlayer starts playing the video clip on the device display and the TV screen. See ‘RealPlayer’, p. 41.

You can view images as a slide show on TV. All items in an album or marked images are displayed on the TV in full screen while the selected music plays. See ‘Slide show’, p.

61.

Presentations

With presentations, you can view SVG (scalable vector graphics) files, such as cartoons and maps. SVG images maintain their appearance when printed or viewed with different screen sizes and resolutions. To view SVG files, select Presentations, scroll to an image, and select

Options > Play. To pause playing, select Options > Pause.

To zoom in, press . To zoom out, press .

To rotate the image 90 degrees clockwise or counter-clockwise, press or . To rotate the image 45 degrees, press or .

To switch between full screen and normal screen, press .

Image print

Draft

To print images with Image print, select the image you want to print, and the print option in the gallery, camera, image editor, or image viewer.

Use Image print to print your images using a compatible USB data cable, WLAN, Bluetooth connectivity, or a compatible memory card (if available).

You can only print images that are in .jpeg format. The pictures taken with the camera are automatically saved in .jpeg format.

To print to a printer compatible with PictBridge, connect the data cable before you select the print option, and check that the data cable mode is set to Image print or

Ask on connection. See ‘USB’, p. 31.

Printer selection

When you use Image print for the first time, a list of available compatible printers is displayed after you select the image. Select a printer. The printer is set as the default printer.

If you have connected a printer compatible with PictBridge using a compatible USB data cable, the printer is automatically displayed.

If the default printer is not available, a list of available printing devices is displayed.

To change the default printer, select Options > Settings >

Default printer.

Print preview

After you select the printer, the selected images are displayed using predefined layouts. To change the layout, press or to browse through the available layouts for the selected printer. If the images do not fit on a single page, press or to display the additional pages.

Print settings

The available options vary depending on the capabilities of the printing device you selected.

To set a default printer, select Options > Default printer.

To select the paper size, select Paper size, the size of paper from the list, and OK. Select Cancel to return to the previous view.

Movie director

To create muvees, press , and select Gallery, images and videos, and Options > Edit > Create muvee.

Gallery

A muvee is a short, edited video clip that can contain video,

Draft

images, music, and text. Quick muvee is created automatically by Movie director after you select the style

Gallery

for the muvee. Movie director uses the default music and text associated with the chosen style. In a custom muvee you can select your own video and music clips, images and style, and add an opening and closing message. You can send muvees with MMS.

A muvee can be saved in Gallery in .3gp file format.

Create a quick muvee

1 In Gallery, select images and videos for the muvee, and

Options > Edit > Create muvee. The style selection

view opens.

2 Select a style for the muvee from the style list. 3 Select Options > Create muvee.

Create a custom muvee

1 In Gallery, select images and videos for the muvee, and

Options > Edit > Create muvee. The style selection

view opens.

2 Scroll to the desired style, and select Options >

Customize.

3 Reorder and edit the selected items, or add or remove

items from your muvee in Videos & images or Music.

In Videos & images, you can define the order in which the files are played in the muvee. To select the file you want to move, press . Then scroll to the file below which you want to place the marked file, and press . To add or remove images and videos from the muvee, select Options > Add/Remove. To add albums and their content to the muvee, in the image or video clip list view, select Options > Albums. To cut the video clips, In Videos & images, select

Options > Select contents. See ‘Select content’, p. 65.

In Message you can add an opening and closing text to a muvee. In Length, you can define the length of the muvee. Select from the following:

Multimedia message—to optimize the length of the

muvee for MMS sending

Auto-select—to include all the selected images and

video clips in the muvee

Same as music—to set the muvee duration to be the

same as the chosen music clip

User defined—to define the length of the muvee

4 Select Options > Create muvee. The preview view

opens.

5 To preview the custom muvee before saving it, select

Options > Play.

6 To save the muvee, select Options > Save.

To create a new custom muvee by using the same style

Draft

settings, select Options > Recreate.

Select content

To edit the selected video clips, in the Videos & images folder, select Options > Select contents. You can select which parts of the video clip you want to include or exclude in the muvee. In the slide, green indicates included, red indicates excluded, and grey indicates neutral parts.

To include a part of the video clip in the muvee, scroll to the part, and select Options > Include. To exclude a part, select Options > Exclude. To exclude a shot, select

Options > Exclude shot.

To let Movie director randomly include or exclude a certain part of the video clip, scroll to the part, and select

Options > Mark as neutral. To randomly include or

exclude parts of the clip, select Options > Mark all as

neutral.

Settings

In the style selection view, select Options > Customize >

Settings to edit the following options:

Memory in use—Select where to store your muvees.

Resolution—Select the resolution of your muvees. Select Automatic to use the optimal resolution based on the

number and length of the video clips you have selected.

Default muvee name—Set a default name for the muvees.

Print online

With Print online, you can order prints of images online directly to your home, or to a store where you can pick them up. You can also order different products with the selected image, such as mugs or mouse pads. The available products depend on the service provider.

To use Print online, you must have at least one printing service configuration file installed. The files can be obtained from printing service providers that support Print

online.

For more information on the application, see the Additional applications leaflet for your device at

www.nseries.com/support

or your local Nokia website.

Online sharing

With Online share, you can share images and video clips in compatible online albums, weblogs, or in other online sharing services on the web. You can upload content, save unfinished posts as drafts and continue later, and view the content of the albums. The supported content types may vary depending on the service provider.

Gallery

To use Online share, you must subscribe to the service

Draft

with an online image sharing service provider, and create a new account. You can usually subscribe to the service on

Gallery

the web page of the service provider. Contact your service provider for details on subscribing to the service. For more information on compatible service providers, see the product support pages at www.nseries.com/support your local Nokia website.

For more information on the application, see the Additional applications leaflet for your device at

www.nseries.com/support

or your local Nokia website.

Home network

Your device is compatible with Universal Plug and Play architecture (UPnP). Using a WLAN access point device or a WLAN router, you can create a home network and connect compatible UPnP devices that support WLAN to the network, such as your Nokia N95, a compatible PC, a compatible printer, and a compatible sound system or TV, or a sound system or TV equipped with a compatible wireless multimedia receiver.

Using the WLAN function of the Nokia N95 in a home network requires a working WLAN home connection setup and the other target home devices to be UPnP enabled and to be connected to the same home network.

The home network uses the security settings of the WLAN connection. Use the home network feature in a WLAN infrastructure network with a WLAN access point device and encryption enabled.

You can share media files saved in Gallery with other compatible UPnP devices using the home network. To

manage your Home netw. settings, press , and select

Tools > Home netw.. You can also use the home network

to view, play, copy, or print compatible media files from

Gallery. See ‘View and share media files’, p. 68.

Important: Always enable one of the available

encryption methods to increase the security of your WLAN connection. Using encryption reduces the risk of unauthorized access to your data.

Your device is connected to the home network only if you accept a connection request from another compatible device, or in Gallery, select the option to view, play, print, or copy media files on your Nokia N95 or search for other devices in the Home network folder.

Important security information

When you configure your WLAN home network, enable an encryption method on your access point device, then on the other devices you intend to connect to your home network. Refer to the documentation of the devices. Keep

any passcodes secret and in a safe place separate from the

Draft

devices.

To view or change the settings of the WLAN Internet access point in your device, see ‘Access points’, p. 120.

If you use the ad hoc operating mode to create a home network with a compatible device, enable one of the encryption methods in WLAN security mode when you configure the Internet access point. This step reduces the risk of an unwanted party joining the ad hoc network.

Your device notifies you if another device attempts to connect to it and the home network. Do not accept connection requests from an unknown device.

If you use WLAN in a network that does not have encryption, switch off sharing Nokia N95 files with other devices, or do not share any private media files. To change sharing settings, see ‘Home network settings’, p. 67.

Home network settings

To share media files saved in Gallery with other compatible UPnP devices through WLAN, you must create and configure your WLAN home Internet access point, then configure the Home netw. application. See ‘Wireless LAN’, p. 25 and the WLAN settings in ‘Access points’, p. 120.

The options related to Home netw. are not available in

Gallery before the Home netw. settings have been

configured.

When you access the home network application for the first time, the setup wizard opens, and helps you to define the home network settings for your device. To use the setup wizard later, in the home network main view, select

Options > Run wizard, and follow the instructions on the

display.

To connect a compatible PC to the home network, on the PC, you must install the related software from the CD-ROM supplied with your device.

Configure settings

To configure the home network application, select Tools >

Home netw. > Settings and from the following:

Home access point—Select Always ask if you want the

device to ask for the home access point every time you connect to the home network, Create new to define a n ew access point that is used automatically when you use

Home netw., or None. If your home network does not have

WLAN security settings enabled, you get a security warning. You can continue, and switch the WLAN security on later; or cancel defining the access point, and first switch on the WLAN security. See Wireless LAN in ‘Access points’, p. 120.

Gallery

Device name— Enter a name for your device that is shown

Draft

to the other compatible devices in the home network.

Set sharing on and define content

Gallery

Select Tools > Home netw. > Share content.

Content sharing—Allow or deny sharing media files with

compatible devices. Do not set Content sharing on before you have configured all the other settings. If you set

Content sharing on, the other UPnP compatible devices in

the home network can view and copy your files you have selected for sharing in the Images & video folder.

Images & video—Select media files for sharing with other

devices, or view the sharing status of Images & video. To update the content of the folder, select Options > Refresh

content.

View and share media files

If Content sharing is on in your device, the other UPnP compatible devices in the home network can view and copy the media files you have selected to share in Share

content. If you do not want the other devices to access

your files, set Content sharing off. Even if Content

sharing is off in your device, you can still view and copy

the media files stored in another home network device if it is allowed by the other device.

Show media files stored in your device

To select images and videos stored in your device, and show them in another home network device, such as a compatible TV, do the following:

1 In Gallery, select an image or a video clip. 2 Select Options > Show via home network. 3 Select a compatible device in which the media file is

shown. The images are shown both in the other home network device and your device, and the video clips are played only in the other device.

Show media files stored in the other device

To select media files that are stored on another home network device, and show them in your device (or in a compatible TV, for example), do the following:

1 Select Gallery > Home network. Your device starts the

search of other compatible devices. Device names start to appear on the display.

2 Select a device from the list. 3 Select the type of media you want to view from the

other device. The available file types depend on the features of the other device.

4 Select the image, video clip, music clip, or folder you

want to view, and select Options > Show via home

network (images and video) or Play via home network

(music).

5 Select the device in which the file is shown. In the

Draft

home network, you cannot play music in your device, but you can play it in compatible external devices, and use your device as a remote control.

To stop sharing the media file, select Options > Stop

showing.

To print images saved in Gallery through Home netw. with a UPnP compatible printer, select the print option in

Gallery. See ‘Image print’, p. 63. Content sharing does not

have to be switched on.

To search files with different criteria, select Options >

Find. To sort the found files, select Options > Sort by.

Copy media files

To copy or transfer media files from your device to another compatible device, such as a UPnP compatible PC, select a file in Gallery and Options > Move and copy > Copy to

home network or Move to home netw.. Content sharing

does not have to be switched on.

To copy or transfer files from the other device to your device, select a file in the other device and Options > Copy

to phone or Copy to memory card (the name of the

memory card if the memory card is available). Content

sharing does not have to be switched on.

Gallery

Positioning

Draft

The Global Positioning System (GPS) is a worldwide radio navigation system that includes 24 satellites and their

Positioning

ground stations that monitor the operation of the satellites. Your device has an internal GPS receiver.

A GPS terminal, such as the GPS receiver in your device, receives low-power radio signals from the satellites, and measures the travel time of the signals. From the travel time, the GPS receiver can calculate its location to the accuracy of meters.

The coordinates in the GPS are expressed in degrees and decimal degrees format using the international WGS-84 coordinate system.

The Global Positioning System (GPS) is operated by the government of the United States, which is solely responsible for its accuracy and maintenance. The accuracy of location data can be affected by adjustments to GPS satellites made by the United States government and is subject to change with the United States Department of Defense civil GPS policy and the Federal Radionavigation Plan. Accuracy can also be affected by poor satellite geometry. Availability and quality of GPS signals may be affected by your location, buildings, natural obstacles, and weather conditions. The GPS receiver should only be used outdoors to allow reception of GPS signals.

GPS should only be used as a navigation aid. It should not be used for precise location measurement and you should never rely solely on location data from the GPS receiver for positioning or navigation.

Your device also supports Assisted GPS (A-GPS).

Assisted GPS (A-GPS) uses a packet data connection to retrieve assistance data to improve GPS performance. It decreases the time to calculate the current location of your device when your device is receiving signals from satellites.

A-GPS is a network service.

Your device is preconfigured to use the Nokia A-GPS service, if no service provider specific A-GPS settings are available. The assistance data is retrieved from the Nokia A-GPS service server only when needed.

You must have a packet data internet access point defined in the device to retrieve assistance data from the Nokia AGPS service. To define an access point for AGPS, press , and select Tools > Settings > General > Positioning >

Positioning server > Access point. A WLAN access point

cannot be used for this service. The packet data internet access point is asked when GPS is used for the first time in your device.

To enable or disable different positioning methods,

Draft

Positioning (GPS) such as Bluetooth GPS, press , and select Tools > Settings > General > Positioning >

Positioning methods.

GPS receiver

The GPS receiver is located in the bottom of the device. When using the receiver, slide the numeric keypad open and hold the device upright in your hand at an angle of about 45 degrees, with a clear view of the sky. Establishing a GPS connection may take from a couple of seconds to several minutes. Establishing a GPS connection in the car may take longer.

The GPS receiver takes its power from the battery. Using the GPS receiver may drain the battery faster.

About satellite signals

If your device cannot find the satellite signal, consider the following:

• If you are indoors, go outdoors to receive a better

signal.

• If the numeric keypad slide is closed, open it.

• If you are outdoors, move to a more open space.

• Check that your hand does not cover the GPS antenna

of your device. For the location of the antenna, see ‘GPS receiver’, p. 71.

• If the weather conditions are bad, in such a case the

signal strength may also be affected.

• Establishing a GPS connection may take from a couple

of seconds to several minutes.

Satellite status

To check how many satellites your device has found, and whether your device is receiving satellite signals, press , and select Tools > GPS data > Position > Options >

Satellite status. If your device has found satellites, a bar

for each satellite is shown in the satellite info view. The longer the bar, the stronger the satellite signal. When your device has received enough data from the satellite signal to calculate the coordinates of your location, the bar turns black.

Initially your device must receive signals from at least four satellites to be able to calculate the coordinates of your location. When the initial calculation has been made, it may be possible to continue calculating the coordinates of

Positioning

your location with three satellites. However, the accuracy

Draft

is generally better when more satellites are found.

Position requests

Positioning

You may receive a request from a network service to receive your position information. Service providers may offer information about local topics, such as weather or traffic conditions, based upon the location of your device.

When you receive a position request, a message is displayed showing the service that is making the request. Select Accept to allow your position information to be sent or Reject to deny the request.

Maps

Press , and select Maps. With Maps, you can see your current location on the map, browse maps for different cities and countries, search for addresses and different points of interest, plan routes from one location to another, and save locations as landmarks and send them to compatible devices.

You can also purchase extra services, such as city guides and a navigation service with voice guidance.

Maps uses GPS. You can define the positioning methods

used with your device in the device settings. See

‘Positioning’, p. 121. For the most accurate location information, use either the internal GPS or the external GSP receiver.

When you use Maps for the first time, you may need to define an internet access point for downloading map information for your current location. To change the default access point later, select Options > Settings >

Network > Default access point.

Almost all digital cartography is inaccurate and incomplete to some extent. Never rely solely on the cartography that you download for use in this device.

Downloading maps may involve the transmission of large amounts of data through your service provider's network. Contact your service provider for information about data transmission charges.

Tip! You can also download maps by using a wireless

LAN connection.

To receive a note when your device registers to a network outside your home cellular network, select Options >

Settings > Network > Roaming warning > On.

Browse maps

The map coverage varies by country.

When you open Maps, you see an overview of the globe. When your device finds the satellite signal, Maps starts to

locate your device, and zooms in to your current location.

Draft

At the same time, Maps downloads the map of your current location. The maps are automatically saved in the device memory or on a compatible memory card (if inserted).

To view information about satellites when you are using

Maps, select Options > Map options > Satellite info.

When you browse the map on the display, for example, move to another country, a new map is downloaded automatically. All the maps downloaded by Maps are free of charge, but downloading may involve the transmission of large amounts of data through your service provider's network. For more information on data transmission charges, contact your service provider.

Your current location is indicated on the map. The compass rose shows the orientation of the map, which is towards north by default.

To move on the map, scroll up, down, left, or right. To view detailed information of a location on the map, scroll to it, press and select Show details. To return to your current location, select Back or Options > Current location.

To zoom in or out on the map, press or . To switch between the 2-D and 3-D views, press .

To define what kind of points of interest are shown on the map, select Options > Map options > Categories and the desired categories.

To save a location as a landmark, in the desired location, press , and select Save > As landmark, enter a name for the landmark, and select the categories you want to include it in. To take a screenshot of your location, select

Save > As image. The screenshot is saved in Gallery.

To view saved landmarks, select Options > Favorites.

To send a landmark to a compatible device, in Favorites, select Options > Landmark location > Send. If you send the landmark in a text message, the information is converted to plain text.

To adjust the network, routing, and general settings, select

Options > Settings.

To check whether the maps that are downloaded to your device have been updated on the map server, select

Options > Settings > Network > Options > Check for map updates.

To prevent the device from automatically downloading maps through the internet, for example, when you are outside your home cellular network, select Options >

Settings > Network > Use network > Off. Allowing the

device to download maps automatically may involve transmission of large amounts of data through your service provider's network. Contact your service provider for more information on data transmission charges.

To adjust the size of the cache that is used for saving maps, select Options > Settings > Max. memory card use (%).

Positioning

This option is available only when a compatible memory

Draft

card is inserted. When the memory is full, the oldest map data is deleted. The cache cannot be emptied.

Search for locations

Positioning

To view points of interest near your current location or other locations on the map, select Options > Search > By

category.

To search for a point of interest by name, select Options >

Search > By name or start entering the first letters of the

name, and select Search.

To search for a location, select Options > Search > By

address. You must enter the city and country. To use an

address you have saved for a contact in Contacts, select

Options > Search > By address > Options > Select from contacts.

To view a search result on a map, press . To switch between the search results, press or . To move on the map, select Options > Full screen, and use the scroll key.

Plan a route

To plan a route from one location to another (for example, from your home to your office), select Options > Plan

route. Select the start and end point for the route.

To adjust the routing settings, such as the mode of transportation, select Options > Settings > Routing.

To view the route itinerary, select Options > Show route. The route is calculated using the selected routing settings.

To view the itinerary waypoints on the map, select

Options > Show on map.

To run a simulation of the created route, select Options >

Start simulation.

To track the route and your current GPS position, select

Options > Start tracking.

Tip! You can also use a compatible GPS receiver with

Bluetooth connectivity with Maps. For example, in a car, an external GPS receiver can be positioned so that it has a clear view of the sky. To enable the use of an external GPS receiver, see ‘Positioning’, p. 121.

Extra services for Maps

To purchase and download city guides for different cities to your device, or purchase a navigation service with voice guidance to use it in Maps, select Options > Extra

services > Guides or Add navigation.

The downloaded guides are automatically saved in the device memory or on a compatible memory card (if inserted).

Navigation

Draft

After purchasing the navigation upgrade, the service is available through Maps.

After creating a route in Maps, to start navigation to the desired destination with GPS using voice guidance, select

Options > Start navigation.

When you use navigation for the first time, you are prompted to select the language of the voice guidance, and download the voice guidance files of the selected language online. To change the language later, in Maps main view, select Options > Settings > General > Voice

guidance, a language, and download the voice guidance

files for the selected language online.

To discard the created route, and use another route, select

Options > Alternative route.

To view only the next turns and hide the map, select

Options > Map options > Next turns.

To stop navigation, select Options > Stop navigation.

City guides

Guides provide information about attractions, restaurants,

hotels, and other points of interest. The guides must be downloaded and purchased before use.

To browse a downloaded guide, on the My guides tab in

Guides, select a guide and a subcategory (if available).

To download a new guide to your device, in Guides, scroll right to the Nearest guides or All guides tab, select the desired guide, and press OK. To purchase the guide, scroll left to the My guides tab, select the downloaded guide, and enter your payment details. You can pay for the guides through a credit card or have the amount charged to your phone bill.

To confirm the purchase, select OK twice. To receive a confirmation of the purchase through e-mail, enter your name and e-mail address, and select OK.

Landmarks

Press , and select Tools > Landmarks. With

Landmarks, you can save the position information of

specific locations in your device. You can sort the saved locations into different categories, such as business, and add other information, such as addresses, to them. You can use your saved landmarks in compatible applications, such as GPS data and Maps.

The coordinates in the GPS are expressed in degrees and decimal degrees format using the international WGS-84 coordinate system.

To create a new landmark, select Options > New

landmark. To make a positioning request for the

coordinates of your current location, select Current

Positioning

position. To enter the position information manually,

Draft

select Enter manually.

To edit or add information to a saved landmark (for example, a street address), scroll to a landmark, and press

. Scroll to the desired field and enter the information.

Positioning

To view the landmark on the map, select Options > Show

on map. To create a route to the location, select Options > Navigate using map.

You can sort your landmarks into the preset categories, and create new categories. To edit and create new landmark categories, press in Landmarks, and select

Options > Edit categories.

To add a landmark to a category, scroll to the landmark in

Landmarks, and select Options > Add to category. Scroll

to each category to which you want to add the landmark, and select it.

To send one or several landmarks to a compatible device, select Options > Send. Your received landmarks are placed in the Inbox folder in Messaging.

GPS data

Press , and select Tools > GPS data. GPS data is designed to provide route guidance information to a selected destination, position information about your current location, and traveling information, such as the

approximate distance to the destination and approximate duration of travel.

The coordinates in the GPS are expressed in degrees and decimal degrees format using the international WGS-84 coordinate system.

To use GPS data, the GPS receiver of your device must receive position information from at least three satellites to calculate the coordinates of your location.

Route guidance

To use route guidance, select Navigation. Start the route guidance outdoors. If started indoors, the GPS receiver may not receive the necessary information from the satellites.

Route guidance uses a rotating compass on the device display. A red ball shows the direction to the destination, and the approximate distance to it is shown inside the compass ring.

Route guidance is designed to show the straightest route and the shortest distance to the destination, measured in a straight line. Any obstacles on the route, such as buildings and natural obstacles, are ignored. Differences in altitude are not taken into account when calculating the distance. Route guidance is active only when you move.

To set your trip destination, select Options > Set

destination and a landmark as the destination, or enter

the latitude and longitude coordinates. Select Stop

Draft

navigation to clear the destination set for your trip.

Retrieve position information

To view the position information of your current location, select Position. An estimate of the accuracy of the location is shown on the display.

To save your current location as a landmark, select

Options > Save position. Landmarks are saved locations

with more information, and they can be used in other compatible applications and transferred between compatible devices.

Trip meter

Select Trip distance > Options > Start to activate trip distance calculation, and Stop to deactivate it. The calculated values remain on the display. Use this feature outdoors to receive a better GPS signal.

Select Reset to set the trip distance and time and average and maximum speeds to zero, and to start a new calculation. Select Restart to also set the odometer and total time to zero.

The trip meter has limited accuracy, and rounding errors may occur. Accuracy can also be affected by availability and quality of GPS signals.

Positioning

Personalize your device

Draft

To personalize your device, select from the following:

• To use the standby display for fast access to your most

frequently used applications, see ‘Active standby mode’, p. 80.

• To change the standby mode background image or

what is shown in the screen saver, see ‘Change the look of your device’, p. 80.

• To customize the ringing tones, see ‘Profiles—set tones’,

Personalize your device

p. 78 and ‘Add ringing tones for contacts’, p. 102.

• To change the shortcuts assigned for the different

presses of the scroll key and left and right selection keys in the standby mode, see ‘Standby mode’, p. 113.

• To change the clock shown in the standby mode, press

, and select Applications > Clock > Options >

Settings > Clock type > Analog or Digital.

• To change the welcome note to an image or animation,

press , and select Tools > Settings > General >

Personalization > Display > Welcome note / logo.

• To change the main menu view, in the main menu,

select Options > Change Menu view > Grid or List.

• To use animated icons in your device, in the main menu,

select Options > Icon animation > On.

• To rearrange the main menu, in the main menu, select

Options > Move, Move to folder, or New folder. You

can move less used applications into folders and place

applications that you use more often into the main menu.

Profiles—set tones

To set and customize the ringing tones, message alert tones, and other tones for different events, environments, or caller groups, press , and select Tools > Profiles.

To change the profile, select Tools > Profiles, a profile, and

Options > Activate. You can also change the profile by

pressing in the standby mode. Scroll to the profile you want to activate, and select OK.

Tip! To switch between the normal and silent profiles,

press and hold .

To modify a profile, press , and select Tools > Profiles. Scroll to the profile, and select Options > Customize. Scroll to the setting you want to change, and press to open the choices. Tones stored on a compatible memory card (if inserted) are indicated with .

In the tones list, the Download sounds link (network service) opens a list of bookmarks. You can select a bookmark and start connection to a web page to download more tones.

If you want the caller’s name to be spoken when your

Draft

device rings, select Options > Customize, and set Say

caller's name to On. The caller’s name must be saved in Contacts.

To create a new profile, select Options > Create new.

Offline profile

The Offline profile lets you use the device without connecting to the wireless network. When you activate the

Offline profile, the connection to the wireless network is

turned off, as indicated by in the signal strength indicator area. All wireless RF signals to and from the device are prevented. If you try to send messages, they are placed in the outbox to be sent later.

When the Offline profile is active, you can use your device without a (U)SIM card.

Important: In the offline profile you cannot make or

receive any calls, or use other features that require cellular network coverage. Calls may still be possible to the official emergency number programmed into your device. To make calls, you must first activate the phone function by changing profiles. If the device has been locked, enter the lock code.

When you have activated the Offline profile, you can still use the WLAN, for example, to read your e-mail or browse on the internet. Remember to comply with any applicable

safety requirements when establishing and using a WLAN connection. See ‘Wireless LAN’, p. 25. You can also use Bluetooth connectivity while in the Offline profile. See ‘Bluetooth connectivity’, p. 27.

To leave the Offline profile, press the power key, and select another profile. The device re-enables wireless transmissions (providing there is sufficient signal strength).

3-D tones

Press , and select Tools > 3-D tones. With 3-D tones you can enable three-dimensional sound effects for ringing tones. Not all ringing tones support 3-D effects.

To enable the 3-D effects, select 3-D ringing tone

effects > On. To change the ringing tone, select Ringing tone and the desired ringing tone.

To change the 3–D effect that is applied to the ringing tone, select Sound trajectory and the desired effect. To modify the effect, select from the following settings:

Trajectory speed—Scroll left or right to adjust the speed at

which sound moves from one direction to another. This setting is not available for all ringing tones.

Reverberation—Select the type of echo.

Personalize your device

Doppler effect—Select On to have the ringing tone sound

Draft

higher when you are closer to your device, and lower when you are farther away. When you get closer to the device, the ringing tone appears to become higher, and lower when you move away from it. This setting is not available for all ringing tones.

To listen to the ringing tone with the 3–D effect, select

Options > Play tone.

If you enable the 3-D tones but do not select any 3-D effect, stereo widening is applied to the ringing tone.

Personalize your device

To adjust the ringing tone volume, select Tools >

Profiles > Options > Customize > Ringing volume.

Change the look of your device

To change the look of the display, such as the wallpaper and icons, press , and select Tools > Themes.

To change the theme that is used for all the applications in your device, select Themes > General. To change the theme of a certain application, in the main view, select an application.

To preview a theme before activating it, select Options >

Preview. To activate the theme, select Options > Set. The

active theme is indicated by .

The themes on a compatible memory card (if inserted) are indicated by . The themes on the memory card are not available if the memory card is not inserted in the device. If you want to use the themes saved in the memory card without the memory card, save the themes in the device memory first.

To change the layout of the main menu, select Themes >

Menu view.

To open a browser connection and download more themes, in General or Menu view, select Download themes (network service).

Important: Use only services that you trust and that

offer adequate security and protection against harmful software.

To edit the wallpaper and power saver of the current theme, select Themes > Wallpaper to change the background image on the display for the active standby mode or Power saver to change the power saver that appears on the display for the active standby mode. See also ‘Display’, p. 112 for power saver time-out setting.

Active standby mode

The active standby display shows application shortcuts, and events from applications such as calendar and player.

To switch the active standby on or off, press , and select

Draft

Tools > Settings > General > Personalization > Standby mode > Active standby.

Scroll to an application or event, and press .

The standard scroll key shortcuts available in the standby mode cannot be used when the active standby mode is on.

To change the default applications’ shortcuts, press , and select

Tools > Settings > General > Personalization > Standby mode > Active standby apps..

Some shortcuts may be fixed, and you cannot change them.

Personalize your device

Time management

Draft

Clock

Press , and select Applications > Clock. To view your active and inactive alarms, press . To set a new alarm, select Options > Set non-repeated alarm. When an alarm is active, is shown.

Time management

To turn off the alarm, select Stop. To stop the alarm for 5 minutes, select Snooze.

If the alarm time is reached while the device is switched off, the device switches itself on and starts sounding the alarm tone. If you select Stop, the device asks whether you want to activate the device for calls. Select No to switch off the device or Yes to make and receive calls. Do not select Yes when wireless phone use may cause interference or danger.

To cancel an alarm, select Applications > Clock >

Options > Remove alarm.

To change clock settings, select Applications > Clock >

Options > Settings > Time or Date, Clock type, or Clock alarm tone.

To allow the mobile phone network to update the time, date, and time zone information to your device (network service), select Network operator time > Auto-update.

World clock

To open the world clock view, select Clock, and press twice. In the world clock view, you can view the time in different cities. To add cities to the list, select Options >

Add city. You can add a maximum of 15 cities to the list.

To set your current city, scroll to a city, and select

Options > Set as current city. The city is displayed in the

clock main view, and the time in your device is changed according to the city selected. Check that the time is correct and matches your time zone.

Calendar

Press , and select Calendar. To add a new calendar entry, scroll to the desired date, select Options > New

entry and one of the following:

1 Meeting—to remind you of an appointment that has a

specific date and time

Meeting request—to create and send a new meeting

request. You need to have a mailbox set up for sending requests. See ‘Mailbox’, p. 88.

Memo—to write a general entry for a day

Anniversary—to remind you of birthdays or special

Draft

dates (entries are repeated every year)

To-do—to remind you of a task that needs doing by a

specific date

2 Fill in the fields. To set

an alarm, select

Alarm > On, and enter

the Alarm time and

Alarm date.

To add a description for an entry, select

Options > Add description.

3 To save the entry,

select Done.

Shortcut: In the day, week, or month calendar view, press any key ( — ). An appointment entry opens, and the characters you enter are added to Subject. In the to-do view, a to-do note entry opens.

When the calendar alarms for a note, select Silence to turn off the calendar alarm tone. The reminder text stays on the screen. To end the calendar alarm, select Stop. To set the alarm to snooze, select Snooze.

You can synchronize your calendar with a compatible PC using Nokia PC Suite. When creating a calendar entry, set the desired Synchronization option.

Calendar views

Select Options > Settings to change the starting day of the week or the view that is shown when you open the calendar.

To go to a certain date, select Options > Go to date. To jump to today, press .

To switch between the month view, week view, day view, and to-do view, press .

To send a calendar note to a compatible device, select

Options > Send.

If the other device is not compatible with Coordinated Universal Time (UTC), the time information of received calendar entries may not be displayed correctly.

To modify the calendar, select Options > Settings >

Calendar alarm tone, Default view, Week starts on, and Week view title.

Manage your calendar entries

To delete more than one event at a time, go to the month view, and select Options > Delete entry > Before date or

All entries.

Time management

To mark a task as completed, scroll to it in the to-do view,

Draft

and select Options > Mark as done.

Time management

Messaging

Draft

Press , and select Messaging (network service).

Only devices that have compatible features can receive and display multimedia messages. The appearance of a message may vary depending on the receiving device.

To create a new message, select New message.

Messaging contains the following folders:

Inbox—Received messages, except e-mail and cell

broadcast messages, are stored here. E-mail messages are stored in the Mailbox.

My folders—Organize your messages into folders.

Tip! To avoid rewriting messages that you send often, use texts in the templates folder. You can also create and save your own templates.

Mailbox—Connect to your remote mailbox to retrieve

your new e-mail messages or view your previously retrieved e-mail messages offline. See ‘E-mail’, p. 92.

Drafts—Draft messages that have not been sent are

stored here.

Sent—The last messages that have been sent,

excluding messages sent using Bluetooth connectivity or

infrared, are stored here. To change the number of messages to be saved, see ‘Other settings’, p. 94.

Outbox—Messages waiting to be sent are temporarily

stored in the outbox, for example, when your device is outside network coverage.

Reports—You can request the network to send you a

delivery report of the text messages and multimedia messages you have sent (network service).

To enter and send service requests (also known as USSD commands), such as activation commands for network services, to your service provider, select Options > Service

command in the main view of Messaging.

Cell broadcast (network service) allows you to receive

messages on various topics, such as weather or traffic conditions, from your service provider. For available topics and relevant topic numbers, contact your service provider. In the main view of Messaging, select Options > Cell

broadcast.

Cell broadcast messages cannot be received in WCDMA networks. A packet data connection may prevent cell broadcast reception.

Messaging

Write text

Draft

ABC, abc, and Abc indicate the selected character mode. 123 indicates the number mode.

To switch between the letter and number mode, press and

Messaging

hold . To switch between the different character modes, press .

To insert a number in the letter mode, press and hold the desired number key.

is displayed when you write text using traditional

text input and when using predictive text input.

With predictive text, you can enter any letter with a single keypress. Predictive text input is based on a built-in dictionary to which you can add new words.

To activate predictive text input, press , and select

Predictive text on.

Tip! To turn predictive text input on or off, quickly

press twice.

Edit text and lists

• To mark an item in a list, scroll to it, and press and

at the same time.

• To mark multiple items in a list, press and hold

while you press or . To end the selection, release

, then release .

• To copy and paste text, while pressing and holding ,

press or to highlight text. To copy the text to clipboard, while still holding , select Copy. To insert the text into a document, press and hold , and select Paste.

Write and send messages

Before you can create a multimedia message or write an e-mail, you must have the correct connection settings in place. See ‘E-mail settings’, p. 88 and ‘E-mail’, p. 92.

The wireless network may limit the size of MMS messages. If the inserted picture exceeds this limit, the device may make it smaller so that it can be sent by MMS.

1 Select New message and from the following:

Text message—to send a text message Multimedia message—to send a multimedia message

(MMS)

Audio message—to send an audio message (a

multimedia message that includes one sound clip)

E-mail—to send an e-mail

2 In the To field, press to select recipients or groups

from contacts, or enter the recipient’s phone number or e-mail address. To add a semicolon (;) that separates the recipients, press . You can also copy and paste the number or address from the clipboard.

3 In the Subject field, enter the subject of a multimedia

Draft

message or e-mail. To change the fields that are visible, select Options > Address fields.

4 In the message field, write

the message. To insert a template, select

Options > Insert or Insert object > Template.

5 To add a media object to a

multimedia message, select Options > Insert

object > Image, Sound clip, or Video clip.

6 To take a new picture or

record sound or video for a multimedia message, select Insert new > Image, Sound clip, or Video clip. To insert a new slide to the message, select Slide. To see what the multimedia message looks like, select

Options > Preview.

7 To add an attachment to an e-mail, select Options >

Insert > Image, Sound clip, Video clip, Note, or Other

for other file types. E-mail attachments are indicated by .

8 To send the message, select Options > Send, or press

Note: Your device may indicate that your message

was sent to the message center number programmed

into your device. Your device may not indicate whether the message is received at the intended destination. For more details about messaging services, contact your service provider.

Your device supports the sending of text messages beyond the character limit for a single message. Longer messages are sent as a series of two or more messages. Your service provider may charge accordingly. Characters that use accents or other marks, and characters from some language options, take up more space, limiting the number of characters that can be sent in a single message.

You may not be able to send video clips that are saved in the .mp4 format or that exceed the size limit of the wireless network in a multimedia message. To edit such a video clip for sending, see ‘Edit video clips to send’, p. 60.

Tip! You can combine images, video, sound, and text

to a presentation and send it in a multimedia message. Start to create a multimedia message, and select

Options > Create presentation. The option is shown

only if MMS creation mode is set to Guided or Free. See ‘Multimedia messages’, p. 91.

Inbox—receive messages

In the Inbox folder, indicates an unread text message,

an unread multimedia message, an unread audio

Messaging

message, data received through infrared, and

Draft

data received through Bluetooth connectivity.

When you receive a message, and 1 new message are shown in the standby mode. To open the message, select Show. To open a message in Inbox, scroll to it, and

Messaging

press . To reply to a received message, select Options >

Multimedia messages

Important: Exercise caution when opening

messages. Multimedia message objects may contain malicious software or otherwise be harmful to your device or PC.

You may receive a notification that a multimedia message is waiting in the multimedia message center. To start a packet data connection to retrieve the message to your device, select Options > Retrieve.

When you open a multimedia message ( ), you may see an image and a message. is shown if sound is included, or if video is included. To play the sound or the video, select the indicator.

To see the media objects that have been included in the multimedia message, select Options > Objects.

If the message includes a multimedia presentation, is displayed. To play the presentation, select the indicator.

Data and settings

Your device can receive many kinds of messages that contain data, such as business cards, ringing tones, operator logos, calendar entries, and e-mail notifications. You may also receive settings from your service provider or company information management department in a configuration message.

To save the data from the message, select Options and the corresponding option.

Web service messages

Web service messages are notifications (for example, news headlines) and may contain a text message or a link. For availability and subscription, contact your service provider.

Mailbox

E-mail settings

Tip! Use Settings wizard to define your mailbox

settings. Press , and select Tools > Sett. wizard.

To use e-mail, you must have a valid internet access point (IAP) in the device and define your e-mail settings correctly. See ‘Access points’, p. 120.

If you select Mailbox in the Messaging main view and

Draft

have not set up your e-mail account, you are prompted to do so. To start creating the e-mail settings with the mailbox guide, select Start. See also ‘E-mail’, p. 92.

You must have a separate e-mail account. Follow the instructions given by your remote mailbox and internet service provider (ISP).

When you create a new mailbox, the name you give to the mailbox replaces Mailbox in the Messaging main view. You can have up to six mailboxes.

Open the mailbox

When you open the mailbox, the device asks if you want to connect to the mailbox (Connect to mailbox?).

To connect to your mailbox and retrieve new e-mail headings or messages, select Yes. When you view messages online, you are continuously connected to a remote mailbox using a data connection.

To view previously retrieved e-mail messages offline, select

No.

To create a new e-mail message, select New message > E-

mail in the messaging main view or Options > Create message > E-mail in your mailbox. See ‘Write and send

messages’, p. 86.

Retrieve e-mail messages

If you are offline, select Options > Connect to start a connection to the remote mailbox.

Important: Exercise caution when opening messages. E-mail messages may contain malicious software or otherwise be harmful to your device or PC.

1 When you have an open connection to a remote

mailbox, select Options > Retrieve e-mail and one of the following:

New—to retrieve all new messages Selected—to retrieve only the messages that have been

marked

All—to retrieve all messages from the mailbox

To stop retrieving messages, select Cancel.

2 If you want to close the connection and view the e-mail

messages offline, select Options > Disconnect.

3 To open an e-mail message, press . If the e-mail

message has not been retrieved and you are offline, you are asked if you want to retrieve this message from the mailbox.

To view e-mail attachments, open the message, and select the attachment field indicated by . If the attachment has a dimmed indicator, it has not been retrieved to the device; select Options > Retrieve.

Messaging

Retrieve e-mail messages automatically

Draft

To retrieve messages automatically, select Options > E-

mail settings > Automatic retrieval. For more

information, see ‘Automatic retrieval’, p. 93.

Messaging

Setting the device to retrieve e-mail automatically may involve the transmission of large amounts of data through your service provider's network. Contact your service provider for information about data transmission charges.

To cancel deleting an e-mail from the device and server, scroll to an e-mail that has been marked to be deleted during the next connection ( ), and select Options >

Restore.

Disconnect from the mailbox

When you are online, to end the data connection to the remote mailbox, select Options > Disconnect.

Delete e-mail messages

To delete the contents of an e-mail message from the device while still retaining it in the remote mailbox, select

Options > Delete. In Delete message from:, select Phone only.

The device mirrors the e-mail headings in the remote mailbox. Although you delete the message content, the e-mail heading stays in your device. If you want to remove the heading as well, you must first delete the e-mail message from your remote mailbox, and then make a connection from your device to the remote mailbox again to update the status.

To delete an e-mail from the device and the remote mailbox, select Options > Delete. In Delete message

from:, select Phone and server.

View messages on a SIM card

Before you can view SIM messages, you must copy them to a folder in your device.

1 In the Messaging main view, select Options > SIM

messages.

2 Select Options > Mark/Unmark > Mark or Mark all to

mark messages.

3 Select Options > Copy. A list of folders opens. 4 To start copying, select a folder and OK. To view the

messages, open the folder.

Messaging settings

Fill in all fields marked with Must be defined or with a red asterisk. Follow the instructions given by your service provider. You may also obtain settings from your service provider in a configuration message.

Some or all message centers or access points may be preset

Draft

for your device by your service provider, and you may not be able to change, create, edit, or remove them.

Reply via same center—Select whether you want the reply

message to be sent using the same text message center number (network service).

Text messages

Press , and select Messaging > Options > Settings >

Text message and from the following:

Message centers—View a list of all text message centers

that have been defined.

Character encoding— To use character conversion to

another encoding system when available, select Reduced

support.

Message center in use—Select which message center is

used to deliver text messages.

Receive report—Select whether the network sends

delivery reports on your messages (network service).

Message validity—Select how long the message center

resends your message if the first attempt fails (network service). If the message cannot be sent within the validity period, the message is deleted from the message center.

Message sent as—Contact your service provider to learn if

your message center is able to convert text messages into these other formats.

Preferred connection—Select the connection to be used.

Multimedia messages

Press , and select Messaging > Options > Settings >

Multimedia message and from the following:

Image size—Define the size of the image in a multimedia

message.

MMS creation mode —If you select Guided, the device

informs you if you try to send a message that may not be supported by the recipient. If you select Restricted, the device prevents you from sending messages that may not be supported. To include content in your messages without notifications, select Free.

Access point in use—Select which access point is used as

the preferred connection.

Multimedia retrieval—Select how you want to receive

messages. To receive messages automatically in your home cellular network, select Auto in home netw.. Outside your home cellular network, you receive a notification that there is a message to retrieve in the multimedia message center.

Outside your home cellular network, sending and receiving multimedia messages may cost you more.

Messaging

If you select Multimedia retrieval > Always automatic,

Draft

your device automatically makes an active packet data connection to retrieve the message both in and outside your home cellular network.

Allow anon. msgs.—Select whether you want to reject

Messaging

messages from an anonymous sender.

Receive ads—Define whether you want to receive

multimedia message advertisements.

Receive report—Select whether you want the status of the

sent message to be shown in the log (network service).

Deny report sending—Select whether you want to deny

your device sending delivery reports of received messages.

Message validity—Select how long the message center

resends your message if the first attempt fails (network service). If the message cannot be sent within the validity period, the message is deleted from the message center.

E-mail

Press , and select Messaging > Options > Settings >

E-mail.

To select which mailbox you want to use for sending e-mail, select Mailbox in use and a mailbox.

Select Mailboxes and a mailbox to change the following settings: Connection settings, User settings, Retrieval

settings, and Automatic retrieval.

To remove a mailbox and its messages from your device, scroll to it, and press .

To create a new mailbox, select Options > New mailbox.

Connection settings

To edit the settings for the e-mail you receive, select

Incoming e-mail and from the following:

User name—Enter your user name, given to you by your

service provider.

Password—Enter your password. If you leave this field

blank, you are prompted for the password when you try to connect to your remote mailbox.

Incoming mail server—Enter the IP address or host name

of the mail server that receives your e-mail.

Access point in use—Select an internet access point (IAP).

See ‘Access points’, p. 120.

Mailbox name—Enter a name for the mailbox.

Mailbox type—Defines the e-mail protocol that your

remote mailbox service provider recommends. The options are POP3 and IMAP4. This setting cannot be changed.

Security (ports)—Select the security option used to secure

Draft

the connection to the remote mailbox.

Port—Define a port for the connection.

APOP secure login (for POP3 only)—Use with the POP3

protocol to encrypt the sending of passwords to the remote e-mail server while connecting to the mailbox.

To edit the settings for the e-mail you send, select

Outgoing e-mail and from the following:

My e-mail address—Enter the e-mail address given to you

by your service provider.

Outgoing mail server—Enter the IP address or host name

of the mail server that sends your e-mail. You may only be able to use the outgoing server of your service provider. Contact your service provider for more information.

The settings for User name, Password, Access point in

use, Security (ports), and Port are similar to the ones in Incoming e-mail.

User settings

My name—Enter your own name. Your name replaces your

e-mail address in the recipient’s device when the recipient’s device supports this function.

Send message—Define how e-mail is sent from your

device. Select Immediately for the device to connect to the mailbox when you select Send message. If you select

During next conn., e-mail is sent when the connection to

the remote mailbox is available.

Send copy to self—Select whether you want to send a

copy of the e-mail to your own mailbox.

Include signature—Select whether you want to attach a

signature to your e-mail messages.

New e-mail alerts—Select whether you want to receive

the new e-mail indications (a tone, a note, and a mail indicator) when new mail is received.

Retrieval settings

E-mail to retrieve—Define which parts of the e-mail are

retrieved: Headers only, Partially (kB) (POP3), or Msgs. &

attachs. (POP3).

Retrieval amount—Define how many new e-mail

messages are retrieved to the mailbox.

IMAP4 folder path (for IMAP4 only)—Define the folder

path for folders to be subscribed.

Folder subscriptions (for IMAP4 only)—Subscribe to other

folders in the remote mailbox and retrieve content from those folders.

Automatic retrieval

E-mail notifications—To automatically retrieve the

headings to your device when you receive new e-mail in

Messaging

your remote mailbox, select Auto-update or Only in home

Draft

netw..

E-mail retrieval—To automatically retrieve the headings

of new e-mail messages from your remote mailbox at defined times, select Enabled or Only in home netw..

Messaging

Define when and how often the messages are retrieved.

E-mail notifications and E-mail retrieval cannot be

active at the same time.

Web service messages

Press , and select Messaging > Options > Settings >

Service message. Select whether you want to receive

service messages. If you want to set the device to automatically activate the browser and start a network connection to retrieve content when you receive a service message, select Download messages > Automatically.

Cell broadcast

Check the available topics and related topic numbers with your service provider. Press , and select Messaging >

Options > Settings > Cell broadcast and from the

following:

Reception—Select whether you want to receive cell

broadcast messages.

Language—Select the languages in which you want to

receive messages: All, Selected, or Other.

Topic detection—Select whether the device automatically

searches for new topic numbers, and saves the new numbers without a name to the topic list.

Other settings

Press , and select Messaging > Options > Settings >

Other and from the following:

Save sent messages—Select whether you want to save a

copy of the text messages, multimedia messages, or e-mail that you send to the Sent folder.

Number of saved msgs.—Define how many sent messages

are saved to the Sent folder at a time. When the limit is reached, the oldest message is deleted.

Memory in use—If a compatible memory card is inserted

in the device, select the memory where you want to save your messages: Phone memory or Memory card.

Make calls

Draft

Voice calls

1 In the standby mode, enter the phone number,

including the area code. To remove a number, press . For international calls, press twice for the + character (replaces the international access code), and enter the country code, area code (omit the leading zero if necessary), and phone number.

2 Press to call the number. 3 Press to end the call (or to cancel the call attempt).

Pressing always ends a call, even if another application is active. Closing the slide does not end an active voice call.

To adjust the volume during a call, use the volume key on the side of your device. You can also use the scroll key. If you have set the volume to Mute, select Unmute first.

To make a call from Contacts, press , and select

Contacts. Scroll to the desired name, or enter the first

letters of the name to the search field. Matching contacts are listed. To call, scroll to the desired contact, and press

You must copy the contacts from your SIM card to

Contacts before you can make a call this way. See ‘Copy

contacts’, p. 101.

To call a recently dialed number in the standby mode, press

. Scroll to the number, and press .

To send an image or a video clip in a multimedia message to the other participant of the call, select Options > Send

MMS (in WCDMA networks only). You can edit the

message and change the recipient before sending. Press

to send the file to a compatible device (network

service).

To put an active voice call on hold while answering another incoming call, select Options > Hold. To switch between the active and the held call, select Options > Swap. To connect the active and held calls and drop yourself from the line, select Options > Transfer.

To send touch tone strings (for example, a password), select Options > Send touch tones. Enter the touch tone string or search for it in Contacts. To enter a wait character (w) or a pause character (p), press repeatedly. Select OK to send the tone. You can add touch tones to the Phone number or Touch tones fields in a contact card.

Make calls

Tip! When you have only one active voice call, to put

Draft

the call on hold, press . To activate the call, press again.

During an active call, to route the sound from the handset to the loudspeaker, select Options > Activate

Make calls

loudspeaker. If you have attached a compatible headset

with Bluetooth connectivity, to route the sound to the headset, select Options > Activate handsfree. To switch back to the handset, select Options > Activate handset.

To end an active call and replace it by answering the waiting call, select Options > Replace.

If you have several calls active, to end them all, select

Options > End all calls.

Many of the options that you can use during a voice call are network services.

Voice mailbox

To call your voice or mailbox (network service), press and hold in the standby mode. See also ‘Call forwarding’, p. 118.

To change the phone number of your voice mailbox, press

, and select Tools > Call mailbox and Options >

Change number. Enter the number (obtained from your

wireless service provider), and select OK.

Make a conference call

1 Make a call to the first participant. 2 To make a call to another participant, select Options >

New call. The first call is automatically put on hold.

3 When the new call is answered, to join the first

participant in the conference call, select Options >

Conference.

To add a new person to the call, repeat step 2, and select Options > Conference > Add to conference. Your device supports conference calls between a maximum of six participants, including yourself. To have a private conversation with one of the participants, select Options > Conference > Private. Select a participant, and select Private. The conference call is put on hold on your device. The other participants can still continue the conference call. After you finish the private conversation, select

Options > Add to conference to return to the

conference call. To drop a participant, select Options > Conference >

Drop participant, scroll to the participant, and select Drop.

4 To end the active conference call, press .

1-touch dial a phone number

Draft

To activate 1-touch dialing, press , and select Tools >

Settings > Phone > Call > 1-touch dialing > On.

To assign a phone number to one of the 1-touch dialing keys ( — ), press , and select Tools > 1-touch. Scroll to the key to which you want to assign the phone number, and select Options > Assign. is reserved for the voice mailbox, and for starting the web browser.

To call in the standby mode, press the speed dial key and

Voice dialing

Your device supports enhanced voice commands. Enhanced voice commands are not dependent on the speaker’s voice, so the user does not record voice tags in advance. Instead, the device creates a voice tag for the entries in contacts, and compares the spoken voice tag to it. The voice recognition in the device adapts to the main user’s voice to recognize the voice commands better.

The voice tag for a contact is the name or nickname that is saved on the contact card. To listen to the synthesized voice tag, open a contact card, and select Options > Play

voice tag.

Make a call with a voice tag

Note: Using voice tags may be difficult in a noisy

environment or during an emergency, so you should not rely solely upon voice dialing in all circumstances.

When you use voice dialing, the loudspeaker is in use. Hold the device at a short distance away when you say the voice tag.

1 To start voice dialing, in the standby mode, press and

hold the right selection key. If a compatible headset with the headset key is attached, press and hold the headset key to start voice dialing.

2 A short tone is played, and Speak now is displayed. Say

clearly the name or nickname that is saved on the contact card.

3 The device plays a synthesized voice tag for the

recognized contact in the selected device language, and displays the name and number. After a timeout of

2.5 seconds, the device dials the number. If the recognized contact was not correct, select Next to view a list of other matches or Quit to cancel voice dialing.

If several numbers are saved under the name, the device selects the default number if it has been set. Otherwise the device selects the first available number of the following:

Mobile, Mobile (home), Mobile (work), Telephone, Tel. (home), and Tel. (work).

Make calls

Answer or decline a call

Draft

To answer the call, press , or open the slide.

To mute the ringing tone when a call comes in, select

Silence.

Make calls

If you do not want to answer a call, press . If you have activated the Tools > Settings > Phone > Call forward >

Voice calls > If busy function to forward calls, declining

an incoming call also forwards the call. See ‘Call forwarding’, p. 118.

When you select Silence to mute the ringing tone of the incoming call, you can send a text message without rejecting the call informing the caller that you cannot answer the call. Select Options > Send text message. To set up this option and write a standard text message, see ‘Call’, p. 117.

Call waiting

You can answer a call while you have another call in progress if you have activated Call waiting in Tools >

Settings > Phone > Call > Call waiting (network service).

To answer the waiting call, press . The first call is put on hold.

To switch between the two calls, select Options > Swap. To connect an incoming call or a call on hold with an active

call and to disconnect yourself from the calls, select

Options > Transfer. To end the active call, press . To

end both calls, select Options > End all calls.

Log

To monitor the phone numbers of missed, received, and dialed voice calls, press , and select Applications >

Log > Recent calls. The device registers missed and

received calls only if the network supports these functions, the device is switched on, and within the network service area.

To clear all recent call lists, select Options > Clear recent

calls in the recent calls main view. To clear one of the call

registers, open the register you want to erase, and select

Options > Clear list. To clear an individual event, open a

Call timers

To monitor the approximate duration of your incoming and outgoing calls, press , and select Applications >

Log > Call timers.

Note: The actual time invoiced for calls by your

service provider may vary, depending on network features, rounding off for billing, and so forth.

To clear call duration timers, select Options > Clear

Draft

timers. For this you need the lock code. See ‘Phone and

SIM card’, p. 114.

Packet data

To check the amount of data sent and received during packet data connections, press , and select

Applications > Log > Packet data. For example, you may

be charged for your packet data connections by the amount of data sent and received.

Monitor all communication events

Icons in Log are as follows:

Incoming Outgoing Missed communication events

To monitor all voice calls, text messages, or data and WLAN connections registered by the device, press , select

Applications > Log, and press to open the general log.

Subevents, such as a text message sent in more than one part and packet data connections, are logged as one communication event. Connections to your mailbox, multimedia messaging center, or web pages are shown as packet data connections.

To add an unknown phone number from Log to your contacts, select Options > Save to Contacts.

To filter the log, select Options > Filter and a filter.

To erase the contents of the log, recent calls register, and messaging delivery reports permanently, select Options >

Clear log. Select Yes to confirm. To remove a single event

from the log, press .

To set the log duration, select Options > Settings > Log

duration. If you select No log, all the log contents, recent

calls register, and messaging delivery reports are permanently deleted.

Tip! In the details view, you can copy a phone number

to the clipboard, and paste it to a text message, for example. Select Options > Copy number.

To view from the packet data counter how much data is transferred and how long a certain packet data connection lasts, scroll to an incoming or outgoing event indicated by

Pack., and select Options > View details.

Make calls

Contacts (Phonebook)

Draft

Press , and select Contacts. In Contacts you can save and update contact information, such as phone numbers, home addresses, or e-mail addresses of your contacts. You can add a personal ringing tone or a thumbnail image to a contact card. You can also create contact groups, which allow you to send text messages or e-mail to many recipients at the same time. You can add received contact information (business cards) to contacts. See ‘Data and

Contacts (Phonebook)

settings’, p. 88. Contact information can only be sent to or received from compatible devices.

To view the amount of contacts, groups, and the available memory in Contacts, select Options > Contacts info.

Save and edit names and numbers

1 Select Options > New contact. 2 Fill in the fields that you want, and select Done.

To edit contact cards in Contacts, scroll to the contact card you want to edit, and select Options > Edit. You can also search for the desired contact by entering the first letters of the name to the search field. A list of the contacts starting with the letters appear on the display.

100

Tip! To add and edit contact cards, you can also use

Nokia Contacts Editor available in Nokia PC Suite.

To attach a small thumbnail image to a contact card, open the contact card, and select Options > Edit > Options >

Add thumbnail. The thumbnail image is shown when the

contact calls.

To listen to the voice tag assigned to the contact, select a contact card and Options > Play voice tag. See ‘Voice dialing’, p. 97.

To send contact information, select the card you want to send and Options > Send > Via text message, Via

multimedia, Via Bluetooth, Via e-mail, or Via infrared.

See ‘Messaging’, p. 85 and ‘Send data using Bluetooth connectivity’, p. 29.

Tip! To print contact cards on a compatible Basic Print

Profile (BPP) equipped printer with Bluetooth connectivity (such as HP Deskjet 450 Mobile Printer or HP Photosmart 8150), select Options > Print.

To add a contact to a group, select Options > Add to

group: (shown only if you have created a group). See

‘Create contact groups’, p. 102.

To check to which groups a contact belongs, select the contact and Options > Belongs to groups.

Microsoft RM-160 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

For your safety

Support

Help

Nokia support and contact information

Get started

Additional applications

Your Nokia N95

Software updates

Settings

Welcome

Transfer content from another device

Essential indicators

Fast downloading

Volume and loudspeaker control

Multimedia menu

Keypad lock (keyguard)

Headset

Memory card

Insert the memory card

Eject the memory card

Memory card tool

File manager

Memory low—free memory

Download!

Web browser

Connection security

Bookmarks view

Browse the web

Text search

Browser toolbar

Download and purchase items

Mini map

Page overview

Web feeds and blogs

End connection

Empty the cache

Settings

Connections

Wireless LAN

Wireless LAN connections

WLAN wizard

WLAN internet access points

Operating modes

Connection manager

Data connections

Wireless LAN

Bluetooth connectivity

Settings

Security tips

Send data using Bluetooth connectivity

Pair devices

Receive data using Bluetooth connectivity

Remote SIM mode

Infrared connection

PC connections

Synchronization

Device manager

Modem

Media applications

Music player

Play a song

Music menu

Playlists

Music shop

Music shop settings

Transfer music

Transfer music from PC

Music transfer with Windows Media Player

Manual synchronization

Automatic synchronization

Radio

Listen to the radio

Saved stations

Video center

Find and view videos

Internet videos