Microsoft RH-66 User Manual

Nokia 2115 and Nokia 2115i User Guide

LEGAL INFORMATION The wireless device described in this guide is approved for use in CDMA 800 and 1900 networks.

Part No. 9237536, Issue No. 1 Copyright © 2004 Nokia. All rights reserved. Nokia, Nokia Connecting People, Nokia 2115, Nokia 2115i, Xpress-on, Pop-Port, and the Nokia Original Enhancements logos are trademarks or registered trademarks of Nokia Corporation. Other company and product names mentioned herein may be trademarks or trade names of their respective owners.

Includes RSA BSAFE cryptographic or security protocol software from RSA Security.

The information contained in this user guide was written for the Nokia 2115 and the Nokia 2115i products. Nokia operates a policy of ongoing development. Nokia reserves the right to make changes to any of the products described in this document without prior notice.

UNDER NO CIRCUMSTANCES SHALL NOKIA BE RESPONSIBLE FOR ANY LOSS OF DATA OR INCOME OR ANY SPECIAL, INCIDENTAL, AND CONSEQUENTIAL OR INDIRECT DAMAGES HOWSOEVER CAUSED. THE CONTENTS OF THIS DOCUMENT ARE PROVIDED “AS IS.” EXCEPT AS RE QUIR ED BY APPL ICABLE L AW, N O WAR RANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE MADE IN RELATION TO THE ACCURACY AND RELIABILITY OR CONTENTS OF THIS DOCUMENT. NOKIA RESERVES THE RIGHT TO REVISE THIS DOCUMENT OR WITHDRAW IT AT ANY TIME WITHOUT PRIOR NOTICE.

EXPORT CONTROLS

This device may contain commodities, technology, or software subject to export laws and regulations from the U.S. and other countries. Diversion contrary to law is prohibited.

FCC/INDUSTRY CANADA NOTICE

Your phone may cause TV or radio interference (for example, when using a telephone in close proximity to receiving equipment). The FCC or Industry Canada can require you to stop using your telephone if such interference cannot be eliminated. If you require assistance, contact your local service facility. This device complies with part 15 of the FCC rules. Operation is subject to the condition that this device does not cause harmful interference.

Contents

For your safety............................................................................................... 7

Welcome.......................................................................................................... 9

1. Device at a glance.................................................................................. 12

2. Set up your phone.................................................................................. 16

3. Text entry ................................................................................................. 24

4. Contacts .................................................................................................. 27

5. Messages ................................................................................................. 36

6. Call log...................................................................................................... 48

7. Settings .................................................................................................... 52

8. Organizer.................................................................................................. 68

9. Games ....................................................................................................... 76

10.Minibrowser .......................................................................................... 77

11.PC Connectivity..................................................................................... 79

12.Enhancements ....................................................................................... 80

13.Battery information ............................................................................. 82

Care and maintenance.............................................................................. 85

Additional safety information................................................................. 86

Nokia one-year limited warranty........................................................... 91

Index............................................................................................................ 107

Contents

For your safety

Read these simple guidelines. Not following them may be dangerous or illegal. Read the complete user guide for further information.

SWITCH ON SAFELY

Do not switch the device on when wireless phone use is prohibited or when it may cause interference or danger.

ROAD SAFETY COMES FIRST

Obey all local laws. Always keep your hands free to operate the vehicle while driving. Your first consideration while driving should be road safety.

INTERFERENCE

All wireless devices may be susceptible to interference, which could affect performance.

SWITCH OFF IN HOSPITALS

Follow any restrictions. Switch the device off near medical equipment.

SWITCH OFF IN AIRCRAFT

Follow any restrictions. Wireless devices can cause interference in aircraft.

SWITCH OFF WHEN REFUELING

Do not use the phone at a refueling point. Do not use near fuel or chemicals.

SWITCH OFF NEAR BLASTING

Follow any restrictions. Do not use the device where blasting is in progress.

USE SENSIBLY

Use only in the normal position as explained in the product documentation. Don't touch the antenna unnecessarily.

QUALIFIED SERVICE

Only qualified personnel may install or repair this product.

ENHANCEMENTS AND BATTERIES

Use only approved enhancements and batteries. Do not connect incompatible products.

For your safety

WATER-RESISTANCE

Your device is not water-resistant. Keep it dry.

BACKUP COPIES

Remember to make backup copies or keep a written record of all important information stored in your device.

CONNECTING TO OTHER DEVICES

When connecting to any other device, read its user guide for detailed safety instructions. Do not connect incompatible products.

EMERGENCY CALLS

Ensure the device is switched on and in service. Press End as many times as needed to clear the display and return to the main screen. Key in the emergency number, then press Call. Give your location. Do not end the call until given permission to do so.

Welcome

Congratulations on your purchase of the Nokia 2115 or Nokia 2115i mobile device. Your device provides many functions which are practical for daily use, such as a hands-free loudspeaker, alarm clock, calculator, calendar, and more. To personalize your device, you can set your favorite ring tones and select an Xpress-on

■ About your device

The wireless device described in this guide is approved for use on the CDMA 800 or 1900 networks. Contact your service provider for more information about networks.

When using the features in this device, obey all laws and respect privacy and legitimate rights of others.

■ Network Services

To use the device you must have service from a wireless service provider. Many of the features in this device depend on features in the wireless network to function. These Network Services may not be available on all networks or you may have to make specific arrangements with your service provider before you can utilize Network Services. Your service provider may need to give you additional instructions for their use and explain what charges will apply. Some networks may have limitations that affect how you can use network services. For instance, some networks may not support all language-dependent characters and services. See "Network services features," page 65.

Your service provider may have requested that certain features be disabled or not activated in your device. If so, they will not appear in your device menu. Contact your service provider for more information.

color cover.

Warning: To use any features in this device, other than the alarm clock, the phone must be switched on. Do not switch the device on when wireless phone use may cause interference or danger.

■ Shared memory

The following features in this device may share memory: contacts, text messages, ring tones, calendar, and games. Use of one or more of these features may reduce

Welcome

the memory available for the remaining features sharing memory. Your device may display a message that the memory is full when you try to use a shared memory feature. In this case, delete some of the information or entries stored in the shared memory features before continuing. Some of the features, such as messages and ring tones may have a certain amount of memory specially allotted to them in addition to the memory shared with other features.

■ Register your device

Make sure to register your device at www.warranty.nokiausa.com or call 1-888-NOKIA-2U (1-888-665-4228) so that we can serve your needs better if you should need to call a customer center or to have your phone repaired.

■ Get help

Find your device label

If you need help, Nokia Customer Care is available for assistance. Before calling, we recommend that you write down the electronic serial number (ESN) and have it available.

The ESN is found on the type label, which is located beneath the battery on the back of the device.

Contact Nokia

Please have your product with you when contacting either of the following numbers:

Please have your product with you when contacting either of the numbers below:

Nokia Customer Care Center, USA

Nokia Inc. 7725 Woodland Center Boulevard, Suite #150 Tampa, Florida 33614 Tel: 1-888-NOKIA-2U (1-888-665-4228) Fax: 1-813-249-9619 TTY/TDD users: 1-800-24-NOKIA (1-800-246-6542)

Welcome

Customer Care Center, Mexico

Nokia Mexico, S.A. de C.V. Paseo de los Tamarindos 400-A Piso 16 Col. Bosques de las Lomas C.P. 05120 Mexico D.F., Mexico Tel: (55) 261-7200 Fax: (55)261-7299

Customer Care Center, Argentina

Azopardo 1071 C1107ADQ Buenos Aires Argentina Tel: (11) 4307-1427 Fax: (11) 4362-8795

Customer Care Center, Canada

Nokia Products Ltd. 601 Westney Road South Ajax, Ontario L1S 4N7 Tel: 1-888-22-NOKIA (1-888-226-6542) Fax: 1-905-619-4360

Updates

From time to time, Nokia updates this guide to reflect changes. The latest version may be available at www.nokiausa.com. An interactive tutorial for this product may be available at the web site www.nokiahowto.com.

Accessibility solutions

Nokia is committed to making mobile devices easy to use for all individuals, including those with disabilities. For more information visit the web site at

www.nokiaaccessibility.com.

Device at a glance

1. Device at a glance

Power key (1) Microphone (7) Earpiece (2) Charger port (8) Right selection key (3) Scroll up and down key (9) End key (4) Call key (10) Keypad (5) Left selection key (11) Connection port (6) Screen (12)

Device at a glance

■ The start screen

The start screen is home base and indicates your device is in idle mode.

Signal strength (1)—A higher bar indicates a stronger network signal.

Battery level (2)—A higher bar indicates more power in the battery.

Menu (3)—Press the Left selection key to select this option.

Contacts (4)—Press the Right selection key to select this option.

■ Quick keys

At the start screen, scroll up to activate the flashlight, or scroll down to go to the contacts list.

■ Indicators and icons

Icon Indicates...

You have one or more text or picture messages. See "Read a message," page 39.

You have one or more voice messages. See "Voice messages," page 43.

You are making a call with the device. See "Make a call," page 20.

Your device keypad is locked. See "Keyguard," page 22.

Your device is set to the Silent profile. See "Profiles," page 52.

The alarm clock is set to On. See "Alarm clock," page 68.

Device at a glance

Icon Indicates...

The countdown timer is running. See "Countdown timer," page 73.

The stopwatch timing is running in the background. See "Stopwatch," page 74.

Integrated hands free is active.

The timed profile is selected. See "Profiles," page 52.

An enhancement is connected to the device.

Voice privacy encryption is active (or is not active) in the network.

Location info sharing is set to Emergency or On. See "Location info sharing," page 53.

Device is roaming outside of your home network.

Device is in an 1XRTT network. See "Network Services," page 9.

■ Get the most out of this guide

The following sections illustrate the various components of your device. Familiarize yourself with these sections to help you understand the instructions that follow.

This guide uses certain terms for the steps that you are asked to perform:

• Press means to press and release a key quickly. For example, press 7 means press the key on the keypad that is labeled with the number 7 and the letters pqrs.

• Press and hold means to press and hold a key for 2–3 seconds, then release the key.

• Selection keys are used to select menu options. To select an option, press the selection key below the menu item on the device screen.

• Scroll keys are used to move up and down in the menus.

• Press Call to place a call or to answer an incoming call.

• Press End to end a call or press and hold to return to idle mode at the start screen.

Device at a glance

■ Device menus

Device features are grouped according to function and are accessed through the main menus. Each main menu contains submenus and lists from which you can select or view items and customize your device features. You can access these menus and submenus by using the scroll method.

Scroll method

1. At the start screen, select Menu, and scroll through the main menu using the up and down scroll key.

2. When you arrive at a menu, press Select (the Left Selection key) to enter a submenu. Select Connect to enter submenus for minibrowser.

• Select Back from the submenu level to return to the previous menu.

• Select Exit from the main menu level or press End to return to the start

screen from any menu or submenu.

Shortcuts

You can go directly to almost any menu or submenu, as well as activate most features by using a shortcut.

At the start screen, select Menu; then within 3 seconds press the key or keys associated with the menu function you would like to view or activate.

For example, to select the Meeting profile, select Menu 4-1-3-1 from the start screen (Menu > 4 Settings>1 Profiles > 3 Meeting > 1 Activate). After a brief pause, the Meeting profile is activated.

In-phone help

Many features have brief descriptions (help text) that can be viewed on the display. To view these descriptions, scroll to a feature, and wait for about 10 seconds. If needed, select More to view all of the description or Back to exit.

In order to view the descriptions, you must first activate help text.

1. At the start screen, select Menu > Settings > Phone settings > Help text

activation.

2. Select On to display help text or Off to turn this feature off.

Set up your phone

2. Set up your phone

■ The antenna

Your device has an internal antenna located towards the top of the device. Hold the device as you would any other telephone with the antenna area pointed up and over your shoulder.

Note: As with any other radio transmitting device, do not touch the antenna unnecessarily when the device is switched on. Contact with the antenna affects call quality and may cause the device to operate at a higher power level than otherwise needed. Avoid contact with the antenna area when operating the device to optimize antenna performance and battery life.

■ The battery

Important: Always switch the device off and disconnect the charger before

removing the battery.

Before removing the cover, always switch off the power and disconnect the charger and any other device. Avoid touching electronic components while changing the covers. Always store and use the device with the covers attached.

Remove the back cover

1. With the back of the device facing you, push down on the button on the back of the device.

2. Slide the back cover toward the bottom of the device and remove.

Remove the battery

After you have removed the back cover, insert your finger into the finger grip and lift the battery from its compartment.

Set up your phone

Replace the battery

Always use original Nokia batteries. See "Battery information," page 82.

1. Position the battery so the gold-colored contacts match up with those on the device.

The battery label must face away from the device.

2. Insert the battery, gold-colored contact end first, into the battery slot.

3. Push down on the other end of the battery to snap the battery into place.

Replace the back cover

Slide the back cover toward the top of the device until you hear a click and see the back cover release button.

Charge the battery

1. Plug the charger transformer into a standard ac outlet.

2. Insert the charger output plug into the round jack at the bottom end of the device.

After a few seconds, the battery indicator in the display starts to scroll from bottom to top. If the battery is completely discharged, it may take a few minutes before the charging indicator appears on the display or any calls can be made.

Set up your phone

■ Turn on or off

To turn your device on or off, press and hold the power key on top of the device for at least 3 seconds.

■ Connect the headset

A compatible headset may be included with your device or purchased separately as an enhancement. (See "Enhancements," page 80.)

1. Plug the headset connector into the Pop-Port™ connector at the bottom end of your device.

2. Position the headset on your ear.

With the headset connected, you can make, answer, and end calls as usual.

• Use the keypad to enter numbers.

• Press Call to place a call.

• Press End to end a call.

■ Change Xpress-on™ covers

Remove the back cover and the battery

See "Remove the back cover," page 16 and "Remove the battery," page 16 for instructions on removing the back cover and the battery.

Remove the front cover

Gently pull the bottom of the front cover away from the rest of the device, and remove the front cover.

Install the key mat and front cover

1. Remove the key mat from the old front cover.

2. Place the key mat into the new front cover.

Set up your phone

3. Press the front cover and key mat against the device, and snap the front cover into place.

Set up your phone

Replace the battery and back cover

See "Replace the battery," page 17 and "Replace the back cover," page 17.

Insert a photo in the back cover

If your device has a picture frame, you can insert one of your favorite photos in the back cover to personalize it. The size of the photo should not be larger than 45 mm x 25 mm. Trim the sides and corners at the bottom of the photo. Please note, if the photo is smaller than the window size, it may not stay in its position. The photo should be inserted with its image side facing the transparent window of the cover.

■ Make a call

Use the keypad

1. Enter the phone number (including the area code), and press Call. To delete a character to the left of the cursor, select Clear.

2. Press End to end the call or to cancel the call attempt.

Use the contacts list

To enter a number into the contacts list, at the start screen, select Contacts >

Add new, and enter the name and phone number. See "Save an entry," page 28.

1. At the start screen, scroll down to display the contents of your contacts list.

2. Select a contact from the list.

3. Press Call to make the call, or select Details to view details of the entry.

Use the last dialed number

1. At the start screen, press Call to display the last 20 numbers dialed.

2. Scroll to the number (or name) you wish to redial, and press Call.

Set up your phone

Make a conference call

Conference calling is a network service that allows you to take part in a conference call with two other participants.

1. Make a call to the first participant.

2. With the first participant on the line, select Options > New call.

3. Enter the phone number of the second participant, or select Search to retrieve a number from the contacts list.

4. Select Flash.

The first participant is put on hold.

5. When the second participant picks up, press Call to connect the calls.

6. To end the conference call, select Options > End all calls, or press End.

■ Answer calls

Answer or silence/decline

Silence/Decline is a carrier-dependent feature.

1. Press Call, or select Answer to answer the call.

2. To mute the ringing tone, select Silence. If you do not answer the call, the call is eventually forwarded to voicemail.

3. To dismiss and forward the call to voicemail (a carrier-dependent feature), select Dismiss after you have muted the ringing tone, or press End at any time.

Answer a call with locked keypad

To answer a call with the keypad locked, press Call. During the call, all features function as normal. When you end or decline the call, the keypad automatically relocks. See "Keyguard," page 22.

When the device is locked, calls may be possible to the official emergency number programmed into your device.

Set up your phone

Adjust the volume during a call

To increase or decrease the volume during a call, scroll up or down during the call. When adjusting the volume, a bar chart indicates the volume level.

Loudspeaker

You can use the loudspeaker on your device during a call.

Warning: Do not hold the device near your ear when the loudspeaker is in use because the volume may be extremely loud.

• To activate the loudspeaker while in a call, select Loudsp.

• To deactivate the loudspeaker during a call, select Handset.

The loudspeaker is deactivated automatically when a call (or a call attempt) ends or when certain enhancements are connected.

Options during a call

Many of the options that you can use during a call, are network services. Check with your wireless service provider for more information.

Select Options during a call to display a list of options available during a call, then select an option.

■ Keyguard

With keyguard, you can lock the keypad to prevent keys from being pressed accidentally and to prevent accidental calls. If the keypad is locked, it unlocks when you receive a call. After the call, the lock automatically reactivates.

When keyguard is on, calls may be possible to the official emergency number programmed into your device.

To lock the keypad, select Menu and press * within 2 seconds.

To unlock the keypad, select Unlock and press * within 2 seconds.

Set up your phone

■ Flashlight

Your device has a built-in flashlight that you can activate when the device is in the standby mode or when there is a call in progress. To activate the flashlight, scroll up. The light stays on until you release the scroll key.

Scroll up twice in quick succession for the flashlight to stay on continually. Press scroll up again to turn the flashlight off.

You can also use the flashlight to alert you to an incoming call. For more information, see "Personalize a profile," page 52.

Text entry

3. Text entry

You can use two methods for entering text and numbers:

• Standard mode is the only way to enter text into the contacts list, and to rename caller groups.

• Predictive text is a quick and easy method for writing messages and creating a calendar note.

■ Standard mode

Text (Abc)

• Press a key once to insert the first letter on the key, twice for the second letter, etc. If you pause briefly, the last letter in the display is accepted and your device awaits the next entry.

• Press 0 to enter a space thereby accepting a completed word.

• Press 1 to enter a period (.).

• Press * to display special characters. See more about special characters on the following pages.

Numbers (123)

To switch to 123 mode from Abc mode, press and hold # at any message entry screen until the icon in the upper left corner of the display switches from Abc to 123 (or vice versa).

• Select Clear to backspace the cursor and delete a character.

• Select and hold Clear to backspace continuously and delete characters.

Punctuation and special characters

While at any text entry screen, press * to display special characters (press and hold * if predictive text is on). To navigate through the list of special characters, use the scroll key. Once a character is highlighted, select Insert to insert the character into your message.

Text entry

■ Predictive text input

Predictive text input allows you to write messages quickly using your keypad and the built-in dictionary. It is much faster than the standard mode method, because for each letter, you only press the corresponding key on your keypad once.

Activate or deactivate

1. At any text entry screen, select Options > Predictive text.

2. Select the language of your choice.

The language setting affects the time and date formats of the clock, alarm clock, and calendar.

Text entry

The following illustration simulates your display each time a key is pressed. For example, to write Nokia with predictive text on and with the English dictionary selected, press each of the following keys once:

6 6 5 4 2

•Press 0 to enter a space and begin writing the next word.

• If a displayed word is not correct, press * to see other matches. To return to the previous word in the list of matches, select Previous.

•If ? appears after a word, select Spell to add the word to the dictionary.

•Press 1 to insert a period into your message.

•Press and hold * to display special characters. Press * again to cycle through all available characters.

•Press # to switch predictive text on or off and to use predictive text in various modes. As you press #, the following icons (not the descriptions) appear in the upper left of the display screen:

Uppercase text: standard mode is on.

Lowercase text: standard mode is on.

Text entry

Sentence case text: standard mode is on.

Sentence case text: predictive text is on.

Lowercase text: predictive text is on.

Contacts

4. Contacts

The contacts list can hold up to 250 contacts, with multiple numbers and text notes for each contact. The amount of numbers and text entries that you can save may vary, depending on length and the total number of entries in the contacts list.

■ Contacts options

You can access contacts options in one of two ways:

• At the start screen, select Contacts.

• At the start screen, select Menu > Contacts.

In this chapter, to access contacts options, select Contacts.

■ Search

1. At the start screen, select Contacts > Search.

2. Type in the first character of the contact name and highlight the contact you wish to view.

3. Select Details > Options and the action you want to apply to the contact.

■ Add new contacts

Save a name and number

1. At the start screen, enter the phone number you wish to save.

2. Select Options > Save.

3. Enter the name, and select OK.

Save (only) a number

1. At the start screen, enter the phone number you wish to save.

2. Select and hold Options.

Contacts

Save an entry

1. At the start screen, select Contacts > Add new.

2. Enter the name, and select OK.

3. Enter the phone number, and select OK > Done.

Save numbers, text items, and details

You can save different types of phone numbers and short text items per name to the contacts list. The first number you save for any entry is automatically set as the default, but the default number can always be changed. You can save details such as addresses and notes as contact information.

1. At the start screen, scroll down to display a list of entries in your contacts list.

2. Scroll to the entry to which you wish to add a phone number, text item, or other details.

3. Select Details > Options > Add number or Add detail.

4. Select General, Mobile, Home, Work, or Fax type when adding a number; or select E-mail, Web address, Street addr., or Note when adding details.

5. Enter the number or text for the type you have selected, and select OK.

6. To change the type, select Change type in the options list.

To change the default number for the contact entry:

1. At the start screen, scroll down to the entry you wish to change, and select

Details.

2. Scroll to the number you wish to set as default, and select Options > As

primary no.

■ Edit contact name

1. Highlight the phone number of the contact and select Options.

2. Select Edit name and enter your changes; then select OK.

■ Delete contacts list entries

1. At the start screen, select Contacts > Delete.

2. To delete individual entries, select One by one.

Contacts

3. Scroll to the entry you wish to delete, and select Delete > OK to confirm.

4. To delete the entire contents of your contacts list, select D elete all > OK.

5. Enter the lock code, and select OK. See "Security settings," page 62.

■ Add number list entries

Add number allows you to tag each phone number entry with a phone type.

1. At the start screen, select Contacts > Add number.

2. Highlight a contact from the list and select Add.

3. Select the tag as General, Mobile, Home, Work, or Fax and enter the number.

■ Settings

Settings allows you to determine how your phone numbers will be viewed and how much memory remains in the contacts list.

At the start screen, select Contacts > Settings and one of the following:

Scrolling view—Specify how names and numbers are viewed in Contacts list.

Memory status—Determine the amount of space available in Contacts list.

■ 1-touch dialing

You can associate any entry in the contacts list with a key from 2–9. To dial those entries, press and hold the assigned key. 1-touch dialing must be turned on to use this method.

Press the assigned key and Call to 1-touch dial at any time.

Assign a key to 1-touch dialing

1. At the start screen, select Contacts > 1-touch dialing.

2. Select any empty slot and Assign.

3. Enter the number (including the area code), and select OK; or select Search to retrieve a number from the contacts list.

4. Enter the contact name for the number, and select OK.

If 1-touch dialing is off, the device displays a prompt asking if you would like to turn 1-touch dialing on.

Contacts

5. Select Yes to activate 1-touch dialing.

Change 1-touch dialing numbers

1. At the start screen, select Contacts > 1-touch dialing.

2. Select the 1-touch dialing entry you wish to change and Options > Change.

3. Enter the new number and select OK; or select Search to view the contacts list and select a new number.

4. Enter a name for the entry, and select OK.

Delete 1-touch dialing numbers

1. At the start screen, select Contacts > 1-touch dialing.

2. Select the 1-touch dialing location you wish to delete.

3. Select Options > Delete > OK to delete the key assignment.

■ Edit contacts list entries

1. At the start screen, scroll down to display the contents of your contacts list.

2. Select the entry you would like to edit and Details.

Edit phone number

1. Highlight the phone number you would like to edit, and select Options.

2. Select one of the following options and select OK.

Add voice tag—Add a voice tag to the contact.

Edit number—Edit an existing phone number of the contact.

Delete number—Delete a phone number from the contact.

Use number—Display the phone number on the start screen, ready to be

called.

View—View the details of the contact.

Change type—Change the number type to General, Mobile, Home, Work, or Fax.

As primary no.—Change the default number of the contact.

Contacts

Add number—Add a number to the contact.

Add de tail—Add an address or note to the contact.

Caller groups—Add the contact to an existing caller group.

Custom tone—Add a custom ring tone to the contact.

Send bus. card—Send the contact as a business card to another phone.

Send message—Create and send a message to the contact.

1-touch dialing—Add the contact to your 1-touch dialing list.

Edit name—Edit the name of the contact.

View name—View the name of the contact.

Delete—Delete the entire contact entry from your contacts list.

E-mail address entry

1. Highlight the e-mail address entry you would like to send or update, and select Options.

2. Select one of the following options and OK.

Send e-mail—Send an e-mail.

Edit detail—Edit existing details of e-mail.

Delete detail—Delete existing e-mail.

View—View the details of the e-mail contact.

Change type—Change the e-mail type to Web address, Street address:, or Note.

Add number—Add a number to the entry.

Add de tail—Add an address or note to the entry.

Caller groups—Add the e-mail to an existing caller group.

Custom tone—Add a custom ring tone to the contact.

Send bus. card—Send the contact a business card.

Edit name—Edit the name of the contact.

View name—View the name of the contact.

Delete—Delete the entire e-mail entry from your contacts list.

Contacts

Edit other text items

1. Highlight the address entry you would like to edit, and select Options.

2. Select the option you wish to perform and OK.

■ Voice tags

Voice tags allow you to dial a contact by speaking. You can also playback, change, or delete voice tags.

Voice dialing

You can dial up to 25 stored numbers using voice dialing.

Before using voice tags, note the following:

• Voice tags are not language dependent. They are dependent on the speaker’s voice.

• You must say the name exactly as you said it when you recorded it.

• Voice tags are sensitive to background noise. Record voice tags and use them in a quiet environment.

• Very short names are not accepted. Use long names, and avoid similar names for different numbers.

Using voice tags may be difficult in a noisy environment or during an emergency, so you shou ld not rely solely upon voice dialing in all circumstances.

Assign a voice tag to an entry

Before you can use voice dialing, you must first assign a voice tag to the number.

1. At the start screen, use scroll down to enter the contacts list.

2. Highlight the contact you want to assign a voice tag, and select Details >

Options > Add voice tag.

3. Select Start; then speak clearly into the microphone.

Do not select Quit unless you want to cancel the recording.

The device automatically stops recording, saves, and replays the voice tag.

appears next to the phone numbers that have voice tags assigned.

If recording is not successful, your device displays Voice system error. Select Options > Add voice tag, and repeat Step 3.

+ 78 hidden pages