ENGLISH
Introduction
About your headset
With the Nokia Bluetooth Mono Headset BH–
310, you can handle calls hands-free, even
when using two phones at the same time.
The surface of this product is nickel-free.
Read this user guide carefully before using the
product. Also, read the user guide for the device
that you connect to the product.
For more info, go to www.nokia.com/
support.
About Bluetooth connectivity
You can use Bluetooth to make a wireless
connection to other compatible devices, such
as mobile phones.
Devices do not need to be in direct line-ofsight, but they must be within 10 metres (33
feet) of each other. The connection may be
affected by obstructions such as walls or
other electronic devices.
This device is compliant with Bluetooth
Specification 3.0 + EDR supporting the following
profiles: headset profile (1.1) , handsfree profile
(1.5). Check with the manufacturers of other
devices to determine their compatibility with
this device.
Cyan
Magenta
Yellow
Black
ENGLISH
Get started
Keys and parts
1 Charger connector
2 Multifunction key
3 NFC area
4 Earloop
5 Earpiece
6 Carrying clip
7 Microphone
8 Car holder
9 Charger connector
10 Indicator light
Charge the battery
Warning: Use only chargers approved by
Nokia for use with this particular model. The use
of any other types may invalidate any approval
or warranty, and may be dangerous. Use of
unapproved chargers may present a risk of fire,
explosion, or other hazard.
1. Plug the charger into a wall outlet.
2. Plug the charger to the charger connector
on the headset or on the car holder. The
red indicator light turns green when the
battery is fully charged.
3. Unplug the charger from the heads et or car
holder, then from the wall outlet.
Cyan
Magenta
Yellow
Black
ENGLISH
When you unplug a charger, hold and pull the
plug, not the cord.
The fully charged battery has power for up to
5 hours of talk time and up to 114 hours of
standby time. If you keep the headset in the
clip, the standby time is up to 90 days.
When the battery charge is low, the red
indicator light flashes, and you hear a voice
prompt every 5 minutes. If you've switched
voice prompts off, the headset beeps every 5
minutes.
Check the battery charge — When the
headset is switched on and you're not in a
call, press
enough power. If the light is yellow, you may
need to recharge the battery soon. If the light
is red, recharge the battery.
Switch the headset on or off
Switch on — Remove the headset from the
clip or from the car holder. The headset
beeps, and a green indicator light flashes
once.
If you've never paired the headset with a
phone, or you've cleared the pairings, pairing
mode is switched on. Pair and connect the
headset with your phone within 3 minutes.
If you've paired the headset before, it
connects to the last phone it was used with.
If the headset can't find that phone, it tries
the next phone on its list of paired devices. If
. A green light means there is
Cyan
Magenta
Yellow
Black
ENGLISH
not connected to a phone within 30 minutes,
the headset switches off.
Switch off — Put the headset in the clip. The
headset beeps, and a red indicator light
flashes once. All calls are ended.
Tip: Don't have the clip with you? To
switch the headset off, press and hold
for 5 seconds. To switch the
headset on, press
Wear the headset
Slide the earloop behind your ear, then gently
push the earpiece against your ear. Point the
headset towards your mouth.
Change the earpad
1. The headset comes with different-sized
earpads. Select the earpad that fits the
best, and is the most comfortable for your
ear.
2. To change the earpad, pull the current
earpad from the earpiece, and push the
new earpad into place.
The headset is set up to be used on your right
ear.
Use the headset on your left ear — Remove
and attach the earloop so that it is to the left
.
of
When you're not using your headset, keep it
in the clip, or car holder.
.
Cyan
Magenta
Yellow
Black