Micro Sensys iID PENsolid UHF User Manual
iID®PENsolid UHF
User Manual
UserMan-iID PENsolid UHF-002E.DOCX © 2017 microsensys QuickStartGuide
RFID Read/Write Device for mobile scan applications
iID® PENsolid is a mobile RFID device suitable as Bluetooth™ enabled RFID read/write unit for UHF
(868/915 MHz) frequency applications.
Based on it’s PEN style form and the implemented touch tip it can be used as input device for tablets and
smartphones with touch and capacitive screens. iID® PENsolid can be configured in Bluetooth™ HID mode.
In this operation mode it emulates a Bluetooth™ keyboard.
Depending on operation mode, iID® PENsolid works together with Windows, Android and iOS devices.
Product Short Description & available Versions:
iID PENsolid UHFcc System: iID-4000 EU
RFID Pen Style Read/Write Unit v1.00 with RTC, MEM, BT, USB, Li accu
Display: LEDs for power, BT, status Buttons: SCAN, F1, F2
System: iID4000 EU, ISO 18000-6c, EPC G2, all customized
Antenna: P3U Operation Mode: DOC / SPC Bluetooth: SPP / HID
Dimensions: 120x26x20 mm³, Li Ion Battery 450mAh
Including: micro USB cable, hand strap
Product Code: 43.72.850.xx
iID PENsolid UHFcc System: iID-4000 US
RFID Pen Style Read/Write Unit v1.00 US frequency with RTC, MEM, BT, USB, Li accu
Display: LEDs for power, BT, status Buttons: SCAN, F1, F2
System: iID4000 US, ISO 18000-6c, EPC G2, all customized, FCC
Antenna: P3U Operation Mode: DOC / SPC Bluetooth: SPP / HID
Package: 120x26x20 mm³, Li Ion Battery 450mAh
Product Code: 43.72.851.xx
An additional product version of iID® PENsolid is available for HF (13.56 MHz) RFID applications. Please
contact microsensys for further information.
iID®PENsolid UHF
User Manual
UserMan-iID PENsolid UHF-002E.DOCX © 2017 microsensys QuickStartGuide
FCC compliance statement
IC compliance statement
These devices comply with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. These devices may not cause harmful interferences;
2. These devices must accept any interference received, including interference that may cause undesired
operation.
The following figures list the Grant by FCC ID Number for each of the following devices:
FCC ID: ZLCPENSOLIDUFX
Please refer to the FCC’s website ( http://www.fcc.gov/ ) to view the grant and related documentation.
CAUTION !
Exposure to Radio Frequency Radiation. The radiated output of this device is far below the FCC radio
frequency exposure limits. Nevertheless, the device shall be used in such a manner that the potential for
human contact during normal operation is minimized. In order to avoid the possibility of exceeding the FCC
radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8inches) during
normal operation. These devices may not be co-located with any other transmitter or transmitter antenna.
NOTE:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interferences when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Changes or modifications not expressly approved by Microsensys GmbH could void the user’s authority to
operate the equipment described in the manual. This device contains Bluetooth™ module FCC ID:
QOQWT12.
Industry Canada ID: 21228-PENSOLIDUFX, contains Bluetooth™ module IC ID: 5123A-BGTWT12A
This device complies with Industry Canada RSS-210. Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio RSS-210.
L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
iID®PENsolid UHF
User Manual
UserMan-iID PENsolid UHF-002E.DOCX © 2017 microsensys QuickStartGuide
Performance description
iID® PENsolid is suitable for mobile data capture and wireless RFID read / write applications, which can be
connected via its integrated USB interface to PCs. The BluetoothTM-Interface is suitable to connect to smart
phones, tablet computers or laptops.
Based on iID® SPC functionality, scripts can be used for definition of LED, buzzer and button support as well
as communication functionalities as RF, USB and Bluetooth™.
iID® PENsolid is a battery powered device, which can be recharged using the micro USB interface. Battery
cycles may vary from some hours to several days depending on the device configuration. When the device
is connected via it’s USB interface, the device is powered by USB power.
The device is available in several types supporting HF as well as UHF systems suitable for closed coupling
communication with very small sized up to large RFID transponders. Additionally all devices support TELID®
sensor transponder applications.
First commissioning
Before using your device the first time, please charge the internal rechargeable battery using included
micro USB cable.
(1) ON/OFF button
(3) rechargeable battery state
LED (orange)
(4) Bluetooth™ state LED (blue)
(2) SCANbutton
(5)(6) Green and red
operation state LED
Focused RFID
antenna, main RF
field direction
Micro-USB connector
Hole for hand strap, clip
Touch tip
Loading...