Microsens MS657033X User Manual

User Manual – Entry Line

Industrial Gigabit Ethernet

High Power 60/95 W PoE Injector

Gigabit Ethernet Switch with PoE+ for Industrial Use Page 2/11

Table of Contents

General ................................................................................................................................ 3

Benefits................................................................................................................................ 3

Front View ........................................................................................................................... 3

LED Display ......................................................................................................................... 4

Dimensional Drawings....................................................................................................... 4

Mounting ............................................................................................................................. 5

Power Supply / Alarm Contact ........................................................................................ 7

Twisted Pair Connections .................................................................................................. 7

Application .......................................................................................................................... 8

Technical Specifications .................................................................................................... 9

Standard Compliance .......................................................................................................10

Safety Notes ......................................................................................................................10

Order Information .............................................................................................................11

Accessories ........................................................................................................................11

Gigabit Ethernet Switch with PoE+ for Industrial Use Page 3/11

General

This 60/95 Watts, high power single port industrial PoE Injector is equipped with our high efficiency technology to provide up to 95 watts power to your security equipment. The technology will not only power up your PD device, also reduce the excessive heat problem to a minimum. It accepts the input voltage from 48 to 56 VDC to meet IEEE802.3af/at required voltage.

Applications for this PoE Injector are high power demanding end devices such as PTZ cameras with integrated heating and high power lights. It is being rigorously tested for your security, transportation and telco applications.

Benefits

System Interface/Performance

 1x10/100/1000Base-T PoE+ (PSE) port  Supports PSE based on IEEE 802.3af and IEEE 802.3at standards

up to 95 W

 1x10/100/1000Base-T data port

Power Supply

 48..56 VDC Redundant Dual Power Input  Overload current protection  Reverse polarity protection

Chassis/Installation

 IP-30 Protection  DIN-rail and Wall Mount Design

Front View

Gigabit Ethernet Switch with PoE+ for Industrial Use Page 4/11

LED Display

There are diagnostic LED indicators located on the front panel of the industrial switch. They provide real-time information of system and operational status. The following table provides description of the LED status and their meanings for the switch.

LED

Color

Status

Meaning

P1

Green

On

Power 1 is active

Off

Power 1 is inactive

P2

Green

On

Power 2 is active

Off

Power 2 is inactive

Mode A

Green

On

End span PD detected

Off

No PoE supplied

Dimensional Drawings

Dimensional Drawing

Gigabit Ethernet Switch with PoE+ for Industrial Use Page 5/11

Mounting

The industrial switch supports two mounting methods: Wall & DIN-rail.

DIN-Rail Mounting

You can also mount industrial switch on a standard DIN-rail by below steps.

The DIN-rail kit is screwed on the industrial switch at delivery. If the DIN-rail kit is not screwed on the industrial switch, please screw it on the switch first.

1. First, hang the industrial switch to the DIN-rail with angle of inclination.

Installation to DIN-rail (Step 1)

2. Then, lightly push the DIN-rail into the track.

Installation to DIN-rail (Step 2)

3. Check if the DIN-rail is tightened on the track or not.

4. To remove the industrial switch from the track, reverse steps above.

Gigabit Ethernet Switch with PoE+ for Industrial Use Page 6/11

Wall mounting

The industrial switch can be wall-mounted by using the included mounting kit.

1. First, use the screws included in the package to combine the industrial

switch and metal mounting kit and remove the DIN-rail adapter.

2. Then fix the switch with some screws to the wall.

Wall mounting brackets

Gigabit Ethernet Switch with PoE+ for Industrial Use Page 7/11

Power Supply / Alarm Contact

The power supply is done by an external power supply with an output voltage of

48..56 VDC. This power supply is not included at delivery, but can be ordered separately (e.g. MS700455). The connection is done by the pluggable screw terminals on the top of the device. The connection of a redundant power supply can be done by the second screw terminal. Connect positive wire to P+, negative wire to P-, also connect grounding/ earth wire to the grounding screw.

Pin out Power Connector and Alarm Contact

WARNING: Any exceeded input voltage will not make this unit function and may damage this unit!

Warning: Always ground the power source to maintain a clean power input.

Twisted Pair Connections

The integrated auto-crossing function of all twisted pair ports makes the use of crossed patch cables unnecessary. The switch automatically detects the pinout of the connected cable and adapts the port accordingly. For all connections standard 1:1 twisted pair cables can be used.

The Auto-negotiation mechanism detects automatically the speed and transmission mode (full or half duplex) between connected ports. A manual configuration is not required.

Note: Always make sure the total length of the TX cable DOES NOT exceed 100meter. Total length is defined as length A + length B.

PD

Remote Switch

A

B

Gigabit Ethernet Switch with PoE+ for Industrial Use Page 8/11

During 100 Mbps transmission, the maximum total cable length is 100 meter.

During 1000 Mbps speed transmission, recommend maximum cable length less than 90 meter is more desired.

Application

Gigabit Ethernet Switch with PoE+ for Industrial Use Page 9/11

Technical Specifications

Type Industrial Gigabit Ethernet 60/ 95 W PoE Injector,

1x 10/100/1000Base-T(X) data, 1x 10/1000/1000Base-T(X) data with PoE

Cable type Unshielded/shielded twisted pair cable, 100 Ohm,

min. category 5e

Data rate 10, 100 or 1000 Mbps

Power-over-Ethernet PoE+ up to 95 W per port according IEEE802.3af/at

LED displays Power 1/2 (green)

Mode A (PoE injected: green)

Mounting 35 mm top-hat rail, according DIN EN 50 022 optional

wall mounting set

Power supply 48..56 VDC, connections with screw terminals,

redundant ports

Power / relay wiring Wire range: 0.34 mm² to 2.5 mm²

Solid wire (AWG):12-24 / 14-22 Stranded wire (AWG): 12-24 / 14-22 Torque:5 lb-In / 0.5 Nm / 0.56 Nm Wire Strip length: 7-8 mm

Power consumption Typ. 1 W @ 48 VDC without PoE

PoE pin assignment Mode A (End Span), V+ (pin 1, 2), V- (pin 3,6),

V+ (pin 4, 5) and V- (pin 7, 8)

Dimensions 32 x 81.5 x 103.5 mm (w x d x h)

Operating temp. -40° C to 75° C

Storage temp. -40° C to 85° C

Rel. humidity 5% to 95% non-condensing

EMC EN 55022 class A, EN 55024

Shock EN 60068-2-27

Free fall EN 60068-2-32

Vibration EN 60068-2-6

Safety EN 60950-1

CE 2014/30/EU EMC Directive

2011/65/EU RoHS Directive

Gigabit Ethernet Switch with PoE+ for Industrial Use Page 10/11

Standard Compliance

IEEE Standards

 IEEE 802.3 10Base-T Ethernet  IEEE 802.3u 100Base-TX Fast Ethernet  IEEE 802.3ab 1000Base-T Gigabit Ethernet  IEEE 802.3z 1000Base-X Gigabit Ethernet  IEEE 802.3af for PoE (up to 15 Watts per port for PSE)  IEEE 802.3at for PoE+ (up to 30 Watts per port for PSE)

Safety Notes

DANGER: Conductive components of power and telecommunications networks

can carry dangerously high voltage.

To avoid electric shock:

 Do not carry out installation or maintenance work during lightning storms.  All electric installations must be carried out in accordance with local

regulations.

Gigabit Ethernet Switch with PoE+ for Industrial Use Page 11/11

Order Information

Art.-No.

Description

Connectors

MS657033X

Industrial GBE High Power PoE Injector up to 95W, IEEE802.3af/at, 2x Data In/PoE Out,

48..56V power input, 40..+75° C

1x RJ-45 1x RJ-45 PoE 2x Power

Accessories

Art.-No.

Description

Connectors

MS700455

DIN Rail mounting power supply 50 Watt 48VDC/1.05 A, input voltage 85–264 VAC, screw terminals, temp. range -10°C..70°C

In: 3-pin Out: 4-pin

MS700456

DIN Rail mounting power supply 120 Watt 48VDC/2.5 A, input voltage 93-132/180-264 VAC, screw terminals, temp. range 35°C..70°C

In: 3-pin Out: 6-pin

MS700457

DIN Rail mounting power supply 240 Watt 48VDC/5 A, input voltage 93-132/180-264 VAC, screw terminals, temp. range -35°C..70°C

In: 3-pin Out: 6-pin

MICROSENS reserves the right to make any changes wi thout further notice to any product to improve reliabil ity, function or design. MICROSENS does not assume any liability arising out of the application or use of an y product. 0317sh

Microsens MS657033X User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual