5 10/100/1000T Industrial Switch
User Manual
MS655200
Content
Overview ............................................................. 1
Introduction .............................................................. 1
Features ................................................................... 3
Packing List .............................................................. 4
Safety Precaution ..................................................... 4
Hardware Description ......................................... 5
Front Panel ............................................................... 5
Top View .................................................................. 6
Wiring the Power Inputs ........................................... 6
Wiring the Fault Alarm Contact ................................ 7
LED Indicators .......................................................... 7
Ports ......................................................................... 8
Cabling ..................................................................... 9
Mounting Installation ........................................ 10
DIN-Rail Mounting .................................................. 10
Wall Mount Plate Mounting .................................... 12
Hardware Installation ........................................ 13
Installation Steps .............................................. 13
Troubles shooting ............................................. 15
Technical Specification ..................................... 16
Overview
Introduction
The unmanaged industrial switch is a cost-effective solution and meets
the high reliability requirements demanded by industrial applications.
High-Speed Transmissions
The Industrial switch includes a switch controller that can automatically
sense transmission speeds (10/100/1000 Mbps). The RJ-45 interface
can also be auto-detected, so MDI or MDI-X is automatically selected
and a crossover cable is not required. All Ethernet ports have memory
buffers that support the store-and-forward mechanism. This assures
that data is properly transmitted.
Dual Power Input
To reduce the risk of power failure, the Industrial switch provides +12 ~
48 VDC dual power inputs. If there is power failure, Industrial switch will
automatically switch to the secondary power input.
Flexible Mounting
The industrial switch is extremely compact and can be mounted on a
DIN-rail or a panel, so it is suitable for any space-constrained
environment.
Advanced Protection
The power line of Industrial switch supports up to 3,000 VDC EFT
protection, which secure equipment against unregulated voltage and
make systems safer and more reliable. Meanwhile, 6,000 VDC ESD
protections for Ethernet ports make Industrial switch more suitable for
harsh environments.
1
Wide Operating Temperature
The operating temperature of the Industrial switch is between -40 ~
75oC (wide operating temperature model) or -10 ~ 60oC (standard
model). With such a wide range, you can use the Industrial switch in
some of the harshest industrial environments that exist.
Easy Troubleshooting
LED indicators make troubleshooting quick and easy. Each
10/100/1000T port has 2 LEDs that display the link status and
transmission speed. Also the three power indicators P1, P2 and Fault
help you diagnose immediately.
2
Features
Provides 5 x 10/100/1000Base-T Mbps Ethernet ports.
Supports full/half duplex flow control
Supports auto-negotiation
Supports MDI/MDI-X auto-crossover
Supports Jumbo Frame of 9Kbytes
Supports surge (EFT) protection 3,000 VDC for power line
Supports 6,000 VDC Ethernet ESD protection
Supports redundant +12 ~ 48 VDC power input
Provides flexible mounting: DIN-rail, Panel Mounting
Supports operating temperatures from -40 ~ 75oC (wide operating
temperature model) or -10 ~ 60oC (standard model)
3
Attention
IF DC voltage is supplied by an external circuit, please use a
protection device on the power supply input.
Packing List
1 x 5-port 10/100/1000Base-T Industrial Ethernet Switch
1 x User Manual
2 x Wall Mounting Bracket and Screws
Safety Precaution
4
Hardware Description
In this paragraph, we will introduce the Industrial switch’s hardware
spec, port, cabling information, and wiring installation.
Front Panel
The Front Panel of the 5-port 10/100/1000Base-T Industrial Switch is
shown as below.
Front Panel of the 5-port 10/100/1000Base-T Industrial Switch
5
Top View
The top panel of the 5-port 10/100/1000Base-T Industrial Switch is
equipped one terminal block connector of two DC power inputs.
Top panel of the 5-port 10/100/1000BaseTX Industrial Switch
Wiring the Power Inputs
Please follow the steps below to insert the power wire.
1. Insert the positive and negative wires into the V+ and V- contacts on the
terminal block connector.
2. To tighten the wire-clamp screws for preventing the DC wires to loose.
6
Note
The wire gauge for the terminal block should be in the range
between 12~ 24 AWG.
LED
Color
Description
P1
Green
On
Power input 1 is active
Off
Power input 1 is inactive
P2
Green
On
Power input 2 is active
Off
Power input 2 is inactive
Fault
Red
On
Power input 1 or 2 is inactive
Off
Power input 1 and 2 are both functional, or no power
Insert the wires into the fault alarm contact (No. 3 & 4)
Wiring the Fault Alarm Contact
The fault alarm contact is in the middle of terminal block connector as the
picture shows below. Inserting the wires, it will detect the fault status
which the power is failure or port link failure (for managed model) and form
an open circuit.
LED Indicators
There are few LEDs display the power status and network status
located on the front panel of the Industrial switch, each of them has its
own specific meaning as below table.
7
inputs
1 ~ 5
(Upper LED)
Green
On
Connected to network
Flashing
Networking is active at speed of 100Mbps
Off
Not connected to network
1 ~ 5
(Lower LED)
Green
On
Connected to network at speed of 1000Mbps
Off
Not connected to network
Pin Number
Assignment
1
Tx+
2
Tx-
3
Rx+
6
Rx-
Note
“+” and “-” signs represent the polarity of the wires that make up
each wire pair.
Ports
RJ-45 ports (Auto MDI/MDIX): The RJ-45 ports are auto-sensing for
10Base-T, 100Base-TX or 100Base-T devices connections. Auto
MDI/MDIX means that you can connect to another switch or workstation
without changing straight through or crossover cabling. See figures as
below for straight through and crossover cable schematic.
RJ-45 Pin Assignments
All ports on this industrial switch support automatic MDI/MDI-X
operation, you can use straight-through cables (See Figure below) for
all network connections to PCs or servers, or to other switches or hubs.
In straight-through cable, pins 1, 2, 3, and 6, at one end of the cable, are
connected straight through to pins 1, 2, 3 and 6 at the other end of the
cable. The table below shows the 10BASE-T/ 100BASE-TX MDI and
MDI-X port pin outs.
8
Pin MDI-X
Signal Name
MDI Signal Name
1
Receive Data plus (RD+)
Transmit Data plus (TD+)
2
Receive Data minus (RD-)
Transmit Data minus (TD-)
3
Transmit Data plus (TD+)
Receive Data plus (RD+)
6
Transmit Data minus (TD-)
Receive Data minus (RD-)
Straight Through Cable Schematic
Cabling
Use unshielded twisted-pair (UTP) or shielded twisted-pair (STP) cable
for RJ-45 connections: 100Ω Category 3, 4 or 5 cable for 10Mbps
connections, 100Ω Category 5 cable for 100Mbps, or 100Ω Category
5e/above cable for 1000Mbps connections.
The cable between the switch and the link partner (switch, hub,
workstation, etc.) must be less than 100 meters (328 ft.) long.
Cross Over Cable Schematic
9
Rear Panel of
the switch
DIN-Rail
Mounting Installation
DIN-Rail Mounting
The DIN-Rail is screwed on the industrial switch when out of factory. If
the DIN-Rail is not screwed on the industrial switch, please see the
following figure to screw the DIN-Rail on the switch. Follow the steps
below to hang the industrial switch.
1. Use the screws to screw on the DIN-Rail on the industrial switch
2. To remove the DIN-Rail, reverse step 1.
10
3. First, insert the top of DIN-Rail into the track.
4. Then, lightly push the button of DIN-Rail into the track.
5. Check the DIN-Rail is tightly on the track.
6. To remove the industrial switch from the track, reverse the steps above.
11
Wall Mount Plate Mounting
Follow the steps below to mount the industrial switch with wall mount plate.
1. Remove the DIN-Rail from the industrial switch; loose the screws to
remove the DIN-Rail.
2. Place the wall mount plate on the rear panel of the industrial switch.
3. Use the screws to screw the wall mount plate on the industrial switch.
4. Use the hook holes at the corners of the wall mount plate to hang the
industrial switch on the wall.
5. To remove the wall mount plate, reverse steps above.
12
Hardware Installation
In this paragraph, we will describe how to install the 5-port
10/100/1000Base-TX Industrial Switch and the installation points for the
attention.
Installation Steps
1. Unpacked the Industrial switch.
2. Check the DIN-Rail is screwed on the Industrial switch. If the DIN-Rail is
not screwed on the Industrial switch. Please refer to DIN-Rail Mounting
section for DIN-Rail installation. If you want to wall mount the Industrial
switch, then please refer to Wall Mount Plate Mounting section for wall
mount plate installation.
13
3. To hang the Industrial switch on the DIN-Rail track or wall, please refer to
the Mounting Installation section.
4. Power on the Industrial switch. How to wire the power; please refer to the
Wiring the Power Inputs section. The power LED on the Industrial switch
will light up. Please refer to the LED Indicators section for meaning of
LED lights.
5. Prepare the twisted-pair, straight through Category 5 cable for Ethernet
connection.
6. Insert one side of Category 5e or above cables into the Industrial switch
Ethernet port (RJ-45 port) and another side of category 5e or above
cables to the network devices’ Ethernet port (RJ-45 port), ex: switch, Pc or
Server. The UTP port (RJ-45) LED on the Industrial switch will light up
when the cable connected with the network device. Please refer to the
LED Indicators section for LED light meaning.
7. When all connections are all set and LED lights all show in normal, the
installation is complete.
14
Troubles shooting
Verify that you are using the right power cord/adapter (DC 12-48V),
please don’t use the power adapter with DC output higher than 48V, or it
will burn this switch down.
Select the proper UTP cable to construct your network. Please check that
you are using the right cable. Use unshielded twisted-pair (UTP) or shield
twisted-pair (STP) cable for RJ-45 connections: 100Ω Category 3, 4 or 5
cable for 10Mbps connections, 100Ω Category 5 cable for 100Mbps, or
100Ω Category 5e/above cable for 1000Mbps connections. Also be sure
that the length of any twisted-pair connection does not exceed 100 meters
(328 feet).
Diagnosing LED Indicators: the Switch can be easily monitored through
panel indicators, which describes common problems you may encounter
and where you can find possible solutions, to assist in identifying
problems.
IF the power indicator does not light on when the power cord is plugged in,
you may have a problem with power cord. Then check for loose power
connections, power losses or surges at power outlet. IF you still cannot
resolve the problem, contact your local dealer for assistance.
If the Industrial switch LED indicators are normal and the connected
cables are correct and the packets still cannot transmit. Please check your
system’s Ethernet devices’ configuration or status.
15
Communications
Compatibility
IEEE 802.3, 802.3u, 802.3ab
IEEE 802.3x
LAN
10/100/1000Base-T
Transmission Distance
Up to 100 m
Transmission Speed
Up to 1000 Mbps
Interface
Connectors
5 x RJ-45 (5-port 10/100/1000TX)
6-pin removable screw terminal
(power & relay)
LED Indicators
Unit: P1, P2, Fault
Ethernet port: Link/Active (100Mbps)
Link (1000Mbps)
Power
Power Consumption
4.6 W
Power Input
2 x Unregulated +12 ~ 48 VDC
Fault Output
1 Relay Output
Mechanism
Technical Specification
The technical specifications of the Industrial Switch are listed as follows.
16
Dimensions (WxDxH)
30 x 95 x 140 mm
Enclosure
IP-30, Metal shell with solid
mounting kits
Protection
ESD (Ethernet)
6,000 VDC
Surge (EFT for power)
3,000 VDC
Power Reverse
Yes
Environment
Operating Temperature
-40 ~ 75oC
(wide operating temp. model)
-10 ~ 60oC (standard model)
Operating Humidity
5% ~ 95% (non-condensing)
Storage Temperature
-40 ~ 85oC
Certifications
Safety
CE EN60950-1
EMC
CE EN61000-4-2 (ESD)
CE EN61000-4-3 (RS)
CE EN61000-4-4 (EFT)
CE EN61000-4-5 (Surge)
CE EN61000-4-6 (CS)
CE EN61000-4-8
CE EN61000-4-11
CE EN61000-4-12
CE EN61000-6-2
CE EN61000-6-4
17
Free Fall
IEC60068-2-32
Shock
IEC60068-2-27
Vibration
IEC60068-2-6
18
Loading...