Microsens Entry Line Ethernet VDSL2 Extender User Manual

MICROSENS GmbH & Co. KG - Kueferstraße 16 - 59067 Hamm / Germany - Tel. [phone] - FAX -100 - www.microsens.com

Introduce

The Industrial Ethernet to VDSL2 extender is long reach Ethernet module with one
Ethernet port (RJ-45 connector) and one VDSL port (RJ-45 connector). It provides
Ethernet and VDSL technologies to extend Ethernet over single-pair phone line by
using a VDSL signal. Up to 88/49 Mbps transition bandwidth within 200m and 22/5.3
Mbps for 1km long range connections provides ultra-high performance to the pervasive
telephone line network. It has the advantage of minimum installation time and
minimum expense by allowing video streaming and data to share the same telephone
pair without interference.

Features

Standard

IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX

ITU-T

ITU-T

-G.993.1(VDSL)

-G.997.1 compatible

LED Indicators

Per unit: Power1, Power2, P-Fail
LAN port: LNK/ACT, SPD
VDSL port: LNK/ACT, CO

Connector

10/100TX: 1 x RJ-45 with auto MDI/MDI-X function.
VDSL: 1 x RJ-45 with female Phone Jack

DIP Switch

DIP1: Master, Slave switch
DIP2: Impulse noise protection
DIP3: Rate limit control
DIP4: General protection

Cabling

10Base-T: 2-pair UTP/STP Cat. 3, 4, 5 cable EIA/TIA-568
100-ohm (100m)
100Base-TX: 2-pair UTP/STP Cat. 5 cable EIA/TIA-568 100­ohm (100m)
VDSL: Twisted-pair telephone

MICROSENS

Entry Line
Ethernet VDSL2 Extender –
Manual

Ethernet VDSL2 Extender - manual Page 2/9

MICROSENS GmbH & Co. KG - Kueferstraße 16 - 59067 Hamm / Germany - Tel. [phone] - FAX -100 - www.microsens.com

Performance(Based
on AWG26 wires)

Full VDSL2 bandwidth up to: (Down Stream / Up Stream)

- 200m -> 88 / 49Mbps

- 400m -> 63 / 29Mbps

- 600m -> 46 / 18Mbps

- 800m -> 30 / 5.7Mbps

- 1000m -> 22 / 5.3Mbps

- 1500m -> 18 / 0.8Mbps

- 2000m -> 9 / 0.5Mbps

Power

12~48VDC , 24VAC

Power Consumption

4.8 Watts( 48VDC)/ 7.7 Watts( 24VAC)

Operating Temp

-40°C to 75°C

Operating Humidity

5% to 95% (non-condensing)

Storage Temperature

-40°C ~85°C

MBTF

260895 hrs

Dimensions

36.6 x 140 x 95 mm

Enclosure

IP-30, metal shell

Safety

Class 1/ Division 2

EMC

CE, FCC Class A
EN61000-6-4
EN61000-6-2
EN61000-4-2 (ESD)
EN61000-4-3 (Radiated RFI)
EN61000-4-4 (Burst)
EN61000-4-5 (Surge)
EN61000-4-6 (Induced RFI)
EN61000-4-8 (Magnetic Field)
EN61000-4-11 (Voltage Dip)
EN61000-3-2 (Harmonics Current)
EN61000-3-3 (Voltage Fluctuation & Flickers)

Shock / Vibration

IEC60068-2-27 / IEC60068-2-6

Freefall

IEC60068-2-32

Ethernet VDSL2 Extender - manual Page 3/9

MICROSENS GmbH & Co. KG - Kueferstraße 16 - 59067 Hamm / Germany - Tel. [phone] - FAX -100 - www.microsens.com

Package Contents

Beware of which type of extender that you have purchased. And, please refer to the
package content list below to verify them against the checklist.

Industrial Ethernet to VDSL2 extender package contains following items.

• The Industrial Ethernet to VDSL2 extender

• User manual

• Block connector

• 2 wall mount plates and 6 screws

• One DIN-Rail (attached on the switch)

Compare the contents of your standalone extender with the standard checklist above.
If any item is damaged or missing, please contact your local dealer for service.

Hardware Description

The Industrial Ethernet to VDSL2 extender dimension: 36.6 x 140 x 95 mm

The Front Panel of the Industrial Ethernet to VDSL2 extender consists of one Ethernet
port, one VDSL Port, and 3 LED Indicators (Power1, Power2, P-Fail, SPD for LAN port,
LNK/ACT for LAN port, CO, LNK/ACT for VDSL).

Ethernet VDSL2 Extender - manual Page 4/9

MICROSENS GmbH & Co. KG - Kueferstraße 16 - 59067 Hamm / Germany - Tel. [phone] - FAX -100 - www.microsens.com

(1) LAN Port (3) LED

(2) VDSL (4) DIP-Switch

LED Indicators

There are 7 diagnostic LEDs located on the Front panel of converter module. They
provide real-time information of system and optional status. The following table
provides description of the LED status and their meanings for Industrial Ethernet to
VDSL2 extender.

LED Status Meaning

ON Power 1 on

OFF Power 1 off

Power1 (Green)

BLK ---

ON Power 2 on

OFF Power 2 off

Power2 (Green)

BLK ---

ON Power1/Power2 is inactive

OFF

Power1 and Power2 are both
active, or no power input

P-Fail (Red)

BLK ---

1

2

3

4

Ethernet VDSL2 Extender - manual Page 5/9

MICROSENS GmbH & Co. KG - Kueferstraße 16 - 59067 Hamm / Germany - Tel. [phone] - FAX -100 - www.microsens.com

ON Link up

OFF Link down

LNK/ACT for LAN
(Green)

BLK Transmitting

ON 100Mbps

OFF 10Mbps

Speed for LAN
(Amber)

BLK ---

ON

Acting as Customer Premise
Equipment (CPE) side

OFF Acting as Central Office (CO) side

CO (Green)

BLK ---

ON Link up

OFF Link down

LNK/ACT for VDSL
(Green)

BLK Negotiating, Transmitting

DIP-switch

The DIP-switch is used to configure operation mode in below. The default value of
Dipswitch is OFF.

S/W

No

Feature Status Description

ON

Acting as Customer Premise Equipment (CPE)
side 1

Master, Slave

switch

OFF Acting as Central Office (CO) side

ON

Fast mode: Direct data transmission with
latency less than 1ms.

2

Impulse noise

protection

OFF

Interleave mode: Provides communication
protection for up to 250ms impulse noise
latency less than 6ms.

ON

Limit line-rate Disable: Provides up to
100Mbps/60Mbps line rate in short line.

3

Rate limit

control

OFF

Limit line-rate Enable: Line rate limited to 50/20
Mbps.

ON

SNR 6dB: Original and Normal channel noise
protection with 6dB SNR.

4

General

protection

OFF

SNR 9dB: Higher SNR margin (9dB) will result in
less error with more stable VDSL link.

Note:
Please set DIP4 OFF when operating in harden environment. That mean will keep better
performance.

Ethernet VDSL2 Extender - manual Page 6/9

MICROSENS GmbH & Co. KG - Kueferstraße 16 - 59067 Hamm / Germany - Tel. [phone] - FAX -100 - www.microsens.com

Data Rates and Distances

Performance in AWG26 Line at 6db with full rate.

Performance in AWG26

(Fast mode, SNR 6dB, Symetric for ISDN)

Data Rate

Distance(Feet)

Downstream(Mbps) Upstream(Mbps)

0 80.5 88.5
250 83.8 90.6
500 81.4 86.8

1000 63.7 64.4
1500 47.9 40.0
2000 32.3 25.7
2500 23.2 14.3
3000 17.9 16.7
3500 15.4 13.1
4000 12.5 8.1
4500 19.4 0.8
5000 15.8 0.8
5500 12.9 0.7
6000 10.3 0.6
6500 7.6 0.5

Performance in AWG26

(Fast mode, SNR 6dB, 998 for ISDN)

Data Rate

Distance(Feet)

Downstream(Mbps) Upstream(Mbps)

0 93.1 54.6
250 97.1 56
500 95.3 54.1

1000 81 44.1
1500 62.9 28.9
2000 45.8 18.3
2500 34.3 7.1
3000 25.8 7.9
3500 21.8 5.3
4000 16.4 6.2
4500 18.5 0.8
5000 18.4 0.8
5500 14.8 0.7
6000 11.7 0.6
6500 9.5 0.5

Ethernet VDSL2 Extender - manual Page 7/9

MICROSENS GmbH & Co. KG - Kueferstraße 16 - 59067 Hamm / Germany - Tel. [phone] - FAX -100 - www.microsens.com

Mounting Installation

DIN-Rail Mounting

The DIN-Rail is screwed on the unit when out of factory. If the DIN-Rail is not screwed
on the unit, please see the pictures and follow the steps below to screw the DIN-Rail on
the unit.

1. Use the screws to screw the DIN-Rail on the rear side of the unit.

2. To remove the DIN-Rail, reverse the step 1.

3. After the DIN-Rail is screwed on the rear side of the unit, insert the top of DIN-

Rail into the track.

4. Then, lightly push the DIN-Rail into the track.

Ethernet VDSL2 Extender - manual Page 8/9

MICROSENS GmbH & Co. KG - Kueferstraße 16 - 59067 Hamm / Germany - Tel. [phone] - FAX -100 - www.microsens.com

5. Check if the DIN-Rail is tightened on the track or not.

6. To remove the unit from the track, reverse steps above.

Wall Mount Plate Mounting

Follow the steps below to mount the unit with wall mount plate.

1. Remove the DIN-Rail from the unit; loose the screws to remove the DIN-

Rail.

2. Place the wall mount plate on the top & bottom side of the unit.

3. Use the screws to screw the wall mount plate on the unit.

4. Use the hook holes at the corners of the wall mount plate to hang the

unit on the wall.

5. To remove the wall mount plate, reverse steps above.

Ethernet VDSL2 Extender - manual Page 9/9

MICROSENS GmbH & Co. KG - Kueferstraße 16 - 59067 Hamm / Germany - Tel. [phone] - FAX -100 - www.microsens.com

Troubles shooting

Check the configuration DIP-switch. It must be setting in the same operation
mode with the link partner.

Select the proper Copper/Phone-line cable to construct your network. Please
check that you are using the right cable.

Warnings

FCC Warning

This Equipment has been tested and found to comply with the limits for a Class-A
digital device. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy. It may cause harmful interference to radio
communications if the equipment is not installed and used in accordance with the
instructions. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CE Mark Warning

This is a Class-A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

MICROSENS reserves the right to make any changes without further notice to any product to improve reliability, function or design.
MICROSENS does not assume any liability arising out of the application or use of any product. 4909/pp