Microsemi USB0824C, USB0815C, USB0812C, USB0805C, USB0803C Datasheet

8700 E. Thomas Road Scottsdale, AZ 85252 Tel: (480) 941-6300 Fax: (480) 947-1503

USB0803C

thru

DESCRIPTION (500 watt)

USB0824C

This TRANSIENT VOLTAGE SUPPRESSOR (TVS) array is packaged in an SO-8 configuration giving protection to 2 Bidirectional data or

TVSarray Series

interface lines. It is designed for use in applications where protection is required at the board level from voltage transients caused by electrostatic discharge (ESD) as defined in IEC 1000-4-2, electrical fast transients (EFT) per IEC 1000-4-4 and effects of secondary lighting.

These TVS arrays have a peak power rating of 500 watts for an 8/20µsec pulse. This array is suitable for protection of sensitive circuitry consisting of TTL, CMOS DRAM’s, SRAM’s, HCMOS, HSIC microprocessors, UNIVERSAL SERIAL BUS (USB) and I/O transceivers. The USB08XXC product provides board level protection from static electricity and other induced voltage surges that can damage or upset sensitive circuitry.

FEATURES MECHANICAL

• Protects up to 2 Bidirectional lines • Molded SO-8 Surface Mount

• Surge protection Per IEC 1000-4-2, IEC 1000-4-4 • Weight: 0.066 grams (approximate)

• Provides electrically isolated protection • Marking: Logo, device number, date code

• SO-8 Packaging • Pin #1 defined by DOT on top of package

• ULTRA LOW CAPACITANCE 5 pF per line pair

• ULTRA LOW LEAKAGE

MAXIMUM RATINGS PACKAGING

• Operating Temperatures: -550C to +1500C • Tape & Reel EIA Standard 481-1-A

• Storage Temperature: -550C to +1500C • 13 inch reel 2,500, pieces (OPTIONAL)

• Peak Pulse Power: 500 Watts (8/20 µsec, Figure 1) • Carrier tubes 95 pcs per (STANDARD)

• Pulse Repetition Rate: <.01%

ELECTRICAL CHARACTERISTICS PER LINE @ 250C Unless otherwise specified

STAND

OFF

PART

NUMBER

USB0803C U3C 3.3 4 7 11 200 5 -5 USB0805C U5C 5.0 6.0 9.8 13 40 5 1 USB0812C U12C 12.0 13.3 19 26 1 5 8 USB0815C U15C 15.0 16.7 24 32 1 5 11 USB0824C U24C 24.0 26.7 43 57 1 5 28

DEVICE

MARKING

VOLTAGE

VOLTS

MAX MIN MAX MAX MAX MAX MAX

NOTE: TVS product is normally selected based on its stand off Voltage VWM. Product selected voltage should be equal to or greater than the continuous peak operating voltage of the circuit to be protected. Application: The USB08XXC product is designed for transient voltage suppression protection of ESD sensitive components at the board level. It is an ideal product to be used for protection of I/O Transceivers.

BREAKDOWN

VOLTAGE

@1 mA VOLTS

CLAMPING

VOLTAGE

@ 1 Amp

(FIGURE 2)

VOLTS

CLAMPING

VOLTAGE

@ 5 Amp

(FIGURE 2)

VOLTS

LEAKAGE CURRENT

@ V

µA

CAPACITANCE

(f=1 MHz)

@0V

TEMPERATURE

COEFFICIENT

OF V

VBR

mV/°C

MSC0323A.PDF ISO 9001 CERTIFIED REV N 7/07/2000

USB0803C thru USB0824C

INCHES

MILLIMETERS

MAX

MIN

DIM

MAX

MIN

0.197 A0.188

4.77

5.00

0.158

0.150

3.81

4.01

0.069

0.053

1.35

1.75

0.021

0.011

0.28

0.53

0.050

0.016

0.41

1.27

0.050 BSC

1.27 BSC

0.010

0.006

0.15

0.25

0.008

0.004

0.10

0.20

0.206

0.189

4.80

5.23 B C D F

G J K

0.244P0.228

5.79

6.19

WAVE FORMS

100

Peak Value -- Ipp

8 X 20 Waveform

Ipp

Half-Value --

Ipp -- Peak Pulse Current -- % Ipp

20 30

t -- Time in microsec

FIGURE 1 FIGURE 2

Peak Pulse Power Vs Pulse Time Pulse Wave Form

MOUNTING PAD SO-8 CIRCUIT DIAGRAM

0.045±.005

0.245 MIN

.030±.005

.160±.005

.050 TYP

SO-8 PACKAGE

MSC0323A.PDF ISO 9001 CERTIFIED REV N 7/07/2000