Microsemi Corporation SMP6LC12, SMP6LC6.5 Datasheet
8700 E. Thomas Road
Scottsdale, AZ 85252
Tel: (480) 941-6300
Fax: (480) 947-1503
SMP6LC5.0
Thru
DESCRIPTION (600 watt)
This 16 pin 2 line Bidirectional LOW CAPACITANCE array is designed for use
in applications where protection is required at the board level. Providing
protection from voltage transients caused by electrostatic discharge (ESD) as
defined in IEC 1000-4-2, electrical fast transients (EFT) per IEC 1000-4-4, and
effects of secondary lighting as stated by IEC 1000-4-5.
These TRANSIENT VOLTAGE SUPPRESSOR (TVS) Diode Arrays have a
peak power of 600 watts for an 10x1000 µsec pulse and are designed to be
used for secondary surge protection on telephone lines. This device can be
used in either common or differential mode applications. For example in the
circuit diagram on the following page use: TIP to (A) and (C) to ground, RING
to (B) and (D) to ground for common mode, or TIP to (A) and RING to (C), or
TIP to (B) and RING to (D) for differential mode.
FEATURES
• 600 watts Peak Pulse Power 10x1000
• Protects up through 12 Volt Components
• Protects 4 Unidirectional lines or 2 Bidirectional
Lines
• Provides electrically isolated protection
• SO-16 Packaging
• UL 94V-0 Flammability Classification
MECHANICAL
• Molded SO-16 Surface Mount
• Weight: 0.128 grams (approximate)
• Body Marked with Logo, and device number
• Pin #1 defined by DOT on top of package
PACKAGING
MAXIMUM RATINGS
• Operating Temperatures: -550C to +1500C
• Storage Temperature: -55
• Peak Pulse Power: 600 Watts (10/1000 µsec, Figure 1 and 2)
• Pulse Repetition Rate: <.01%
0
C to +1500C
• Tape & Reel EIA Standard 481-1-A
• 13 inch reel 2,500 pieces (OPTIONAL
• Carrier tubes 50 pcs per (STANDARD)
SMP6LC12
TVSarray Series
ELECTRICAL CHARACTERISTICS PER LINE @ 25°C Unless otherwise specified
STAND-OFF
VOLTAGE
V
PART
NUMBER
SMP6LC05 SMP6LC5.0 5.0 6.0 9.6 300 10 30
SMP6LC6.5 SMP6LC6.5 6.5 7.22 12.4 300 10 30
SMP6LC12 SMP6LC12 12.0 13.3 19.9 2.0 10 30
DEVICE
MARKING
WM
VOLTS
MAX MIN MAX TYP TYP TYP
BREAKDOWN
VOLTAGE
V
BR
@10 mA
VOLTS
NOTE: Transient Voltage Suppression (TVS) product is normally selected based on its stand off voltage VWM. Product
selected voltage should be equal to or greater than the continuous or peak operating voltage of the circuit to be
protected.
Application: The SMP6LCXX product is designed for transient voltage suppression protection of components at the
board level. It is an ideal product to be used for protection of HIGH SPEED I/O TRANSCEIVERS.
CLAMPING
VOLTAGE
V
C
@ I
PP
VOLTS
MAXIMUM
LEAKAGE
CURRENT
@V
WM
I
D
µA
PEAK
PULSE
CURRENT
@ 10/1000 µS
I
PP
AMPS
CAPACITANCE
(f=1 MHz)
@0V
C
PER LINE PAIR
pF
MSC1379.PDF ISO 9001 CERTIFIED REV C 10/15/99
SMP6LC6.5 thru SMP6LC12
P
PP
Peak Pulse Power - kW
WAVE FORMS
100
10
1
0.1 1 10 100 1000 10000 100000
T
Pulse Duration µS
d
FIGURE 1
Peak Pulse Power Vs Pulse Time
FIGURE 2
Pulse Wave Form
MOUNTING PAD SO-16 CIRCUIT DIAGRAM
SO-16 PACKAGE
A
INCHES MILLIMETERS
B P
B
C
D
G
D
C
K
L
J
F
F
G
J
K
L
MAXMINDIM MAXMIN
0.398 A 0.358 9.09 10.10
0.1580.150 3.81 4.01
0.0690.053 1.35 1.75
0.0210.011 0.28 0.53
0.0500.016 0.41 1.27
0.050 BSC 1.27 BSC
0.0100.006 0.15 0.25
0.0080.004 0.10 0.20
0.2060.189 4.80 5.23
0.244P 0.228 5.79 6.19
MSC1379.PDF ISO 9001 CERTIFIED REV C 10/15/99
Loading...