Microsemi Corporation SMDA03C-8, SMDA05C-8, SMDA12C-8, SMDA24C-8, SMDA15C-8 Datasheet
8700 E. Thomas Road
SMDA03C-8
Scottsdale, AZ 85251
Tel: (480) 941-6300
thru
Fax: (480) 947-1503
SMDA24C-8
TVSarray Series
DESCRIPTION (300 watt)
This 14 pin 8 line Bi-directional array is designed for use in
applications where protection is required at the board level from
voltage transients caused by electrostatic discharge (ESD) as defined
in IEC 1000-4-2, electrical fast transients (EFT) per IEC 1000-4-4 and
effects of secondary lighting.
These TRANSIENT VOLTAGE SUPPRESSOR (TVS) Diode Arrays
have a peak power of 300 watts for an 8/20 µsec pulse and are designed to protect 3.0/3.3 volt
components such as DRAM’s, SRAM’s, CMOS, HCMOS, HSIC, and low voltage interfaces up to 24 volts.
FEATURES MECHANICAL
• Protects 3.0/3.3 up through 24V Components • Molded SO-14 Surface Mount
• Protects 8 lines Bi-directional • Weight: 0.127 grams (approximate)
• Provides electrically isolated protection • Body Marked with Logo, and device number
• SO-14 Packaging • Pin #1 defined by DOT on top of package
• Encapsulation meets UL 94V-0
MAXIMUM RATINGS PACKAGING
• Operating Temperatures: -550C to +1500C • Tape & Reel EIA Standard 481-1-A
• Storage Temperature: -550C to +1500C • 13 inch reel 2,500 (OPTIONAL)
• Peak Pulse Power: 300 Watts (8/20 µsec, Figure 1) • Carrier tubes 55 pcs per (STANDARD)
• Pulse Repetition Rate: <.01%
ELECTRICAL CHARACTERISTICS@ 250C Unless otherwise specified
STAND
OFF
PART
NUMBER
SMDA03C-8 SDL8 3.3 4 7.0 9.0 200 300 -5
SMDA05C-8 SDB8 5.0 6.0 9.8 11 40 200 1
SMDA12C-8 SDD8 12.0 13.3 19.0 24 1 75 8
SMDA15C-8 SDF8 15.0 16.7 24.0 30 1 50 11
SMDA24C-8 SDH8 24.0 26.7 43.0 55 1 35 28
DEVICE
MARKING
VOLTAG
V
VOLTS
MAX MIN MAX MAX MAX TYP MAX
NOTE: Transient Voltage Suppression (TVS) product is normally selected based on its stand off voltage
VWM. Product selected voltage should be equal to or greater than the continuous peak operating voltage of
the circuit to be protected.
Application: The SMDAXXC-8 product is designed for transient voltage suppression protection of
components at the board level. It is an ideal product to be used for protection of I/O Transceivers.
E
WM
BREAKDOWN
VOLTAGE
V
BR
@1 mA
VOLTS
CLAMPING
VOLTAGE
V
C
@ 1 Amp
(FIGURE 2)
VOLTS
CLAMPING
VOLTAGE
V
C
@ 5 Amp
(FIGURE 2)
VOLTS
LEAKAGE
CURRENT
I
D
@ V
WM
µA
CAPACITANCE
(f=1 MHz)
@0V
C
pF
TEMPERATURE
COEFFICIENT
OF V
BR
á
VBR
mV/°C
MSC0976.PDF ISO 9001 CERTIFIED REV F 7/06/2000
SMDA03C-8 thru SMDA24C-8
WAVE FORMS
100
Peak Value -- Ipp
8 X 20 Waveform
50
Ipp
Half-Value --
0
0
Ipp -- Peak Pulse Current -- % Ipp
t
2
20 30
10
t
d
t -- Time in microsec
FIGURE 1 FIGURE 2
Peak Pulse Power Vs Pulse Time Pulse Wave Form
MOUNTING PAD SO-14 CIRCUIT DIAGRAM
SO-14 PACKAGE
MSC0976.PDF ISO 9001 CERTIFIED REV F 7/06/2000
Loading...