Microsemi SmartFusion2 MSS User Manual

SmartFusion2 MSS

CAN Configuration

SmartFusion2 MSS CAN Configuration

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1 Configuration Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2 Peripheral Signals Assignment Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3 Connectivity Preview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4 Resource Conflicts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Error Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Warning Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Information Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

5 Port Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

A Product Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Customer Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Customer Technical Support Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Website . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Contacting the Customer Technical Support Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

ITAR Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2

Introduction

The SmartFusion2 Microcontroller Subsystem (MSS) provides one CAN hard peripheral (APB_1 sub
bus).

On the MSS Canvas, you must enable (default) or disable the CAN instance based on whether it is being
used in your current application. When disabled, the CAN instance is held in reset (lowest power state).
By default, when enabled, the CAN ports are configured to connect to the device Multi Standard I/Os
(MSIOs). Note that MSIOs allocated to the CAN instance are shared with other MSS peripherals. These
shared I/Os are available to connect to MSS GPIOs and other peripherals when the CAN instance is
disabled or if the CAN instance ports are connected to the FPGA fabric.

The functional behavior of the CAN instance must be defined at the application level using the
SmartFusion2 MSS CAN Driver provided by Microsemi.

In this document, we describe how you can configure the MSS CAN instance and define how the
peripheral signals are connected.

For more details about the MSS CAN hard peripheral, please refer to the SmartFusion2 User Guide.

3

1 – Configuration Options

There are no hardware configuration options for the CAN peripheral.

Note: If the CAN instance is enabled, M3_CLK must be a multiple of 8MHz. This restricti on will be

enforced in the MSS CCC Configurator.

4