Microsemi Corporation SM1603, SM1603C, SM1605, SM1605C, SM1612 Datasheet
...
8700 E. Thomas Road
Scottsdale, AZ 85252
Tel: (480) 941-6300
Fax: (480) 947-1503
SM1603-03C
thru
SM1624-24C
DESCRIPTION (300 watt)
This 16 pin 8 line Unidirectional or Bidirectional array is designed for use in
TVSarray Series
applications where protection is required at the board level from voltage
transients caused by electrostatic discharge (ESD) as defined in IEC 1000-42, electrical fast transients (EFT) per IEC 1000-4-4 and effects of secondary
lighting.
These TRANSIENT VOLTAGE SUPPRESSOR (TVS) Diode Arrays have a
peak power of 300 watts for an 8/20 µsec pulse and are designed to protect
3.0/3.3 volt components such as DRAM’s, SRAM’s, CMOS, HCMOS, HSIC,
and low voltage interfaces up to 24 volts.
FEATURES MECHANICAL
• Protects 3.0/3.3 up through 24V Components • Molded SO-16 Surface Mount
• Protects 8 lines Unidirectional or Bidirectional • Weight: 0.128 grams (approximate)
• Provides electrically isolated protection • Body Marked with Logo, and device number
• SO-16 Packaging • Pin #1 defined by DOT on top of package
• Encapsulation meets UL 94V-0
MAXIMUM RATINGS PACKAGING
• Operating Temperatures: -550C to +1500C • Tape & Reel EIA Standard 481-1-A
• Storage Temperature: -550C to +1500C • 13 inch reel 2,500 pieces (OPTIONAL)
• Peak Pulse Power: 300 Watts (8/20 µsec, Figure 1) • Carrier tubes 48 pcs per (STANDARD)
• Pulse Repetition Rate: <.01%
ELECTRICAL CHARACTERISTICS PER LINE @ 25°C Unless otherwise specified
STAND
OFF
PART
NUMBER
SM1603 MBA 3.3 4 7 9 125 850 -3
SM1603C MBB 3.3 4 7 9 200 425 -5
SM1605 MBC 5.0 6 9.8 11 20 880 3
SM1605C MBD 5.0 6 9.8 11 40 440 1
SM1612 MBE 12 13.3 19 24 1 440 10
SM1612C MBF 12 13.3 19 24 1 220 8
SM1615 MBG 15 16.7 24 30 1 400 13
SM1615C MBH 15 16.7 24 30 1 200 11
SM1624 MBK 24 26.7 43 55 1 275 30
SM1624C MBL 24 26.7 43 55 1 137 28
DEVICE
MARKING
VOLTAGE
V
WM
VOLTS
MAX MIN MAX MAX MAX TYP MAX
BREAKDOWN
VOLTAGE
V
BR
@1 mA
VOLTS
CLAMPING
VOLTAGE
V
C
@ 1 Amp
(FIGURE 2)
VOLTS
CLAMPING
VOLTAGE
V
C
@ 5 Amp
(FIGURE2)
VOLTS
Part numbers with a “C” suffix are bidirectional devices
LEAKAGE
CURREN
T
I
D
@ V
WM
µA
CAPACITANCE
(f=1 MHz)
@0V
C
pF
TEMPERATURE
COEFFICIENT
OF V
BR
áV
BR
mV/°C
NOTE: Transient Voltage Suppression (TVS) product is normally selected based on its stand off voltage VWM. Product
selected voltage should be equal to or greater than the continuous peak operating voltage of the circuit to be protected.
Application: The SM16XX/XXC product is designed for transient voltage suppression protection of components at the
board level. It is an ideal product to be used for protection of I/O Transceivers.
MSC0885.PDF ISO 9001 CERTIFIED REV N 7/07/2000
SM1603-03C thru SM1624-24C
•
1514132418711910
WAVE FORMS
100
Peak Value -- Ipp
8 X 20 Waveform
50
Ipp
Half-Value --
0
0 10 20 30
Ipp -- Peak Pulse Current -- % Ipp
t
2
t
d
t -- Time in microsec
FIGURE 1 FIGURE 2
Peak Pulse Power Vs Pulse Time Pulse Wave Form
MOUNTING PAD SO-16 CIRCUIT DIAGRAM
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
SO-16 PACKAGE
A
INCHES MILLIMETERS
B P
B
C
D
G
D
J
C
K
L
F
F
G
J
K
L
0.050 BSC 1.27 BSC
MAXMINDIM MAXMIN
0.398 A 0.358 9.09 10.10
0.1580.150 3.81 4.01
0.0690.053 1.35 1.75
0.0210.011 0.28 0.53
0.0500.016 0.41 1.27
0.0100.006 0.15 0.25
0.0080.004 0.10 0.20
0.2060.189 4.80 5.23
0.244P 0.228 5.79 6.19
MSC0885.PDF ISO 9001 CERTIFIED REV N 7/07/2000
Loading...