Microsemi PD-9001GC User Manual
English
Deutsch
C6626M 03/19
POE130-AT
Microsemi PD-9001GC
User Guide
1-Port 802.3at Gigabit Midspan
Microsemi PD-9001GC
Benutzeranleitung
1-Port 802.3at Gigabit Midspan
1
Functions and Features
The PD-9001GC is a Power over Ethernet (PoE) Single Port Midspan/Injector that offers a super compact
and cost effective power solution for WLAN access points, network cameras and other IP terminal installations.
The PD-9001GC Power over Ethernet (PoE) Midspan/Injector is IEEE802.3at compliant, it adds 55V DC to wires
4,5,7,8 of a standard Ethernet cable in category 5 and above, and enables delivery of both data and power to the
IP terminal.
The PD-9001GC can be powered via universal AC input and can provide up to 30 Watts.
Main Features:
1-port PoE output
Guaranteed 30W
IEEE802.3at compliant
Super small dimensions
Universal AC input 100-240VAC
10/100/1000mbps pass-through data rates
Notice
It is Microsemi’s policy to improve its products as new technology, components, software, and firmware become
available. Microsemi, therefore, reserves the right to change specifications without prior notice.
Technical Support
If you encounter problems when installing or using this product, please consult the Microsemi website at:
http://www.Microsemi.com.
USA/Canada: +1-949-380-6245 POEsupport@microsemi.com
© 2017 Microsemi Corporation
2
English
Safety Information
Important Safety Information
This injector should be connected to PoE networks only, without routing to outside plant.
The PD-9001GC Ethernet and Terminal ports are shielded RJ45 data sockets. They can’t be used as Plain
Old Telephone Service (POTS) sockets. Only RJ45 data connectors can be connected to these sockets.
The PD-9001GC Ethernet and Terminal interfaces are qualified as Safety Extra-Low Voltage (SELV)
circuits according to IEC 60950-1. These interfaces can only be connected to SELV interfaces on other
equipment.
The power cord must be a three-conductor type (two current carrying conductors; one ground conductor)
terminated on one end by an IEC 60320 appliance coupler (for connection to the PoE Media Converter),
and on the other end by a plug containing a ground (earth) contact.
The power cord must be rated for a minimum of 250Vac RMS operation, with a minimum rated current
capacity of 5 amps (or a minimum wire gauge of 18 AWG (0.823mm2).
WARNINGS!
This Midspan should only be connected to an IP device with which it was bought. Using PD-9001GC with
other IP devices can cause damage to IP device.
Follow basic electricity safety measures whenever connecting PD-9001GC to its power source.
A voltage mismatch can cause equipment damage and may pose a fire hazard. If voltage indicated on the
label is different from the power outlet voltage, do not connect PD-9001GC to this power outlet.
Do not use cross-over cable between the PD-9001GC output port and the load device.
Preliminary Steps
Read installation instructions before connecting the PD-9001GC to its power source.
There is no “on/off” switch; simply plug the PD-9001GC into an AC power source.
Verify that a PoE Ready Ethernet-compatible device is connected.
Do not cover PD-9001GC or block airflow to the unit with any foreign objects. Keep PD-9001GC away from
excessive heat and humidity and free from vibration and dust.
Ensure cable length from Ethernet network source to terminal does not exceed 100 meters (330 feet). This
Midspan is not a repeater and does not amplify Ethernet data signal.
Use a splitter if desired; ensure splitter is connected close to the terminal and not on the PD-9001GC!
PD-9001GC EMC Compliance:
FCC Part 15 class B and EN55032 class B
EN55024
VCCI
PD-9001GC Safety Compliance:
UL/cUL per 60950-1
GS Mark
3
Terminal
Ethernet
Cat 5/5e cable
Input (Ethernet): Ethernet 10/100/1000Base-T
RJ45 female socket
Output (Terminal): Ethernet 10/100/1000BaseT, Plus 55VDC
RJ45 female socket, with DC voltage on wire
pairs, 4, 5 (+) & 7, 8 (-).
Port LED
Indicated Behavior
Yellow On
Power is on (power is active)
Green On
A remote terminal is connected
Green Blinking
Overload state or short-circuit
Installing the Unit
1. Connect the PD-9001GC to an AC outlet (100-240VAC).
2. Connect the “DATA IN” jack (input) to the remote Ethernet network switch's Patch panel.
3. Connect the “PWR OUT” jack (output) to Terminal.
Ethernet Interface
Indicators
4
English
Specifications
Mode
Temperature
Humidity
Operating
-10 to 40°C
14 to 104°F
5 to 95% (non-condensing)
Storage
-20 to 70°C
-4 to 158°F
5 to 95% (non-condensing)
Input Voltage
100-240 VAC (50/60Hz)
Maximal Input Current
1 Ampere
Available Output Power
30 Watts
Nominal Output Voltage
55 VDC
Unit weight
170 gr
Dimensions (W x H x L)
46 x 32 x 141 mm
Environmental Specifications
Electrical Specifications
Physical Specifications
Loading...