Microsemi 1N5333B, 1N5388B User Manual

SCOTTSDALE DIVISION

The 1N5333-5388B JEDEC registered series of axial-leaded 5.0 watt

DESCRIPTION

Zeners provides voltage regulation in a selection from 3.3 to 200 volts with different tolerances as identified by specific suffix letter on the part number. These plastic encapsulated Zeners have moisture classification of Level 1 with no dry pack required and are also available in various military equivalent screening levels by adding a prefix identifier as also described in the Features section. They may be operated at high maximum dc currents with adequate heat sinking with their comparatively low thermal resistance design. Microsemi also offers numerous other Zener products to meet higher and lower power applications.

IMPORTANT: For the most current data, consult

• JEDEC registered 1N5333 to 1N5388B

• Zener voltage available 3.3V to 200V

• Standard voltage tolerances are plus/minus 5%

with B suffix and 10 % with A suffix identification

• Tight tolerances available in plus or minus 2% or 1% with C or D suffix respectively

• Options for screening in accordance with MILPRF-19500 for JAN, JANTX, JANTXV, and JANS are available by adding MQ, MX, MV, or MSP prefixes respectively to part numbers.

• Surface mount equivalents available as SMBJ5333 to SMBJ5388B, or SMBG5333B to SMBG5388B

• Power dissipation at 25 derating in Figure 1).

• Operating and Storage temperature: -65

• Thermal Resistance: 25

• Steady-State Power: 5 watts at T

• Forward voltage @1.0 A: 1.2 volts (maximum)

• Solder Temperatures: 260

+150

3/8 (10 mm) lead length from body, or 85 junction to ambient when mounted on FR4 PC board (1oz Cu) with 4 mm2 copper pads and track width 1 mm, length 25 mm

inch (10 mm) from body, or 1.47 watts at T

C when mounted on FR4 PC described for

25 thermal resistance (also see Figure 1)

FEATURES

MAXIMUM RATINGS

C: 5.0 watts (also see

C/W junction to lead at

C for 10 s (max)

MICROSEMI’s

C to

C/W

< 25oC 3/8

Silicon 5 Watt Zener Diodes

website: http://www.microsemi.com

• Regulates voltage over a broad operating current and

• Wide selection from 3.3 to 200 V

• Flexible axial-lead mounting terminals

• Nonsensitive to ESD per MIL-STD-750 Method 1020

• Withstands high surge stresses

• Minimal changes of voltage versus current as

• High specified maximum current (I

• Moisture classification is Level 1 per IPC/JEDEC J-

• CASE: Void-free transfer molded thermosetting

• TERMINALS: Leads, tin-lead plated solderable per

• POLARITY: Cathode indicated by band. Diode to

• MARKING: Part number

• TAPE & REEL option: Standard per EIA-296 (add

• WEIGHT: 0.7 grams

• See package dimensions on last page

APPLICATIONS / BENEFITS

temperature range

specified by voltage regulation (∆V

adequately heat sunk

STD-020B with no dry pack required

MECHANICAL AND PACKAGING

epoxy body meeting UL94V-0

MIL-STD-750, method 2026

be operated with the banded end positive with respect to the opposite end.

“TR” suffix to part number)

1N5333B thru 1N5388B

APPEARANCE

T-18

)

) when

WWW.

Microsemi

. COM

1N5333B thru 1N5388B

Microsemi

Scottsdale Division

8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503

Page 1

1N5333B thru 1N5388B

Silicon 5 Watt Zener Diodes

SCOTTSDALE DIVISION

*ELECTRICAL CHARACTERISTICS @ 25oC

TYPE

NUMBER

REGULATOR

VOLTAGE

(VZ)

TEST

CURRENT

(IZT)

V mA dc OHMS

1N5333B 1N5334B 1N5335B 1N5336B 1N5337B 1N5338B 1N5339B 1N5340B 1N5341B 1N5342B 1N5343B 1N5344B 1N5345B 1N5346B 1N5347B 1N5348B 1N5349B 1N5350B 1N5351B 1N5352B 1N5353B 1N5354B 1N5355B 1N5356B 1N5357B 1N5358B 1N5359B 1N5360B 1N5361B 1N5362B 1N5363B 1N5364B 1N5365B 1N5366B 1N5367B 1N5368B 1N5369B 1N5370B 1N5371B 1N5372B 1N5373B 1N5374B 1N5375B 1N5376B 1N5377B 1N5378B 1N5379B 1N5380B 1N5381B 1N5382B 1N5383B 1N5384B 1N5385B 1N5386B 1N5387B 1N5388B

3.3

3.6

3.9

4.3

4.7

5.1

5.6

6.0

6.2

6.8

7.5

8.2

8.7

9.1 10 11 12 13 14 15 16 17 18 19 20 22 24 25 27 28 30 33 36 39 43 47 51 56 60 62 68 75 82 87

91 100 110 120 130 140 150 160 170 180 190 200

380 350 320 290 260 240 220 200 200 175 175 150 150 150 125 125 100 100 100

75 75 70 65 65 65 50 50 50 50 50 40 40 30 30 30 25 25 20 20 20 20 20 15 15 15 12 12 10 10

8.0

5.0

*JEDEC Registered Data.

NOTE 1: Devices listed above with B suffix have ±5% tolerance, A suffix designates ±10% tolerance, C suffix designates ±2%

tolerance, and D suffix designates ±1% tolerance. No suffix designates ±20%. NOTE 2: Zener voltage (Vz) is measured at T after application of dc current. NOTE 3: The zener impedance is derived from 1 kHz ac voltage resulting from an ac current modulation having an rms value equal to 10% of the dc zener current (I

variation with different operating currents.

NOTE 4: The maximum current (I the formula: I

for the method of mounting.

NOTE 5: The surge current (I NOTE 6: Voltage regulation (∆V

= P/V

ZSM

MAXIMUM DYNAMIC

IMPEDANCE

(ZZ)

(A&B Suffix)

MAXIMUM REVERSE CURRENT

(IR)

µA

3.0

2.5

2.0

1.5

1.0

1.5

2.0

2.5

3.0

3.5

4.0

5.0

6.0

8.0 10 11 14 20 25 27 35 40 42 44 45 65 75 75 90

125 170 190 230 330 350 380 430 450 480

) shown is for a ±5% tolerance devices. The IZM for other tolerances can be calculated using

where VZM is the VZ at the high end of the voltage tolerance specified and P is the rated power

300 150

50 10

5.0

1.0

1.0 10 10 10 10

7.5

5.0

2.0

1.0

0.5

= 25oC (+8, -2oC). Voltage measurement performed at 40 ±10 milliseconds

or IZK) superimposed on IZT or IZK. See Micro Note 202 for zener impedance

IR TEST

VOLTAGE

(VR)

(Non-Suffix &

A Suffix)

TEST

VOLTAGE

(VR)

(B,C,D Suffix)

MAXIMUM

REGULATOR

CURRENT

(IZM)

(B,C,D Suffix)

MAXIMUM

DYNAMIC KNEE

IMPEDANCE

@ 1.0 mA

ZZK

(A,B,C,D Suffix)

MAXIMUM

SURGE

CURRENT

ZSM

V V mA OHMS AMPS VOLTS

1.0

2.0

3.0

4.9

5.4

5.9

6.25

6.6

7.2

8.0

8.6

9.4

10.1

10.8

11.5

12.2 13

13.7

14.4

15.8

17.3 18

19.4

20.1

21.6

23.8

25.9

28.1 31

33.8

36.7

40.3 43

44.6 49 54 59 63

65.5 72

79.2

86.4

93.6

101 108 115 122 130 137 144

1.0

2.0

3.0

5.2

5.7

6.2

6.6

6.9

7.6

8.4

9.1

9.9

10.6

11.5

12.2

12.9

13.7

14.4

15.2

16.7

18.2 19

20.6

21.2

22.8

25.1

27.4

29.7

32.7

35.8

38.8

42.6

45.5

47.1

51.7 56

62.2 66

69.2 76

83.6

91.2

98.8

106 114 122 129 137 144 152

1440 1320 1220 1100 1010

930 865 790 765 700 630 580 545 520 475 430 395 365 340 315 295 280 264 250 237 216 198 190 176 170 158 144 132 122 110 100

93 86 79 76 70 63 58

54.5

52.5

47.5 43

39.5

36.6 34

31.6

29.4 28

26.4 25

23.6

400 500 500 500 450 400 400 300 200 200 200 200 200 150 125 125 125 100

75 75 75 75 75 75 75

75 100 110 120 130 140 150 160 170 190 210 230 280 350 400 500 620 720 760 760 800

1000 1150 1250 1500 1500 1650 1750 1750 1850 1850

18.7

17.6

16.4

15.3

14.4

13.4

12.7

12.4

11.5

10.7 10

9.5

9.2

8.6

8.0

7.5

7.0

6.7

6.3

6.0

5.8

5.5

5.3

5.1

4.7

4.4

4.3

4.1

3.9

3.7

3.5

3.3

3.1

2.8

2.7

2.5

2.3

2.2

2.1

2.0

1.9

1.8

1.7

1.6

1.5

1.4

1.3

1.2

1.1

1.0

0.9

) is specified as the maximum peak of a non-recurrent half-sine wave of 8.3 ms duration.

) is the difference between the voltage measured at 10% and 50% of IZM.

)

MAXIMUM VOLTAGE

REGULATION

(∆VZ)

(A,B,C,D

Suffix)

0.85

0.80

0.54

0.49

0.44

0.39

0.25

0.19

0.10

0.15

0.20

0.22

0.25

0.30

0.35

0.40

0.45

0.55

0.60

0.65

0.70

0.80

0.90

1.00

1.20

1.35

1.50

1.60

1.80

2.00

2.20

2.30

2.50

3.00

4.00

5.00

WWW.

Microsemi

. COM

1N5333B thru 1N5388B

Microsemi

Scottsdale Division

8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503

Page 2

+ 2 hidden pages