Microplex SOLID 50 A3 - 3 Operator's Manual

________________________________________________________________________________

SOLID 50 A3 - 3

Operator’s Manual

Edition 2.1

2

_______________________________________________________________________________________________

Table of Contents 3

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Table of Contents

Chapter Page

1. Introduction 7

1.1. General Description 7

1.2. Conventions 9

1.3. CE - Conformity 10

1.4. General Safety Instructions 10

2. Installation 13

2.1. Check List 13

2.2. Printer Unpacking 14

2.3. Preparing the Printer 17

2.4. Printer Installation 26

2.5. Printer Components 30

3. Handling of Consumables 32

3.1. Print Media Handling (Paper, e.g.) 32

3.1.1. Loading Cassettes 1 and 2 32

3.1.2. Loading the Multipurpose Feeder 38

3.1.3. Using the Output Bins 41

3.1.4. Changing the Paper Size Setting 42

3.2. Toner Cartridge Replacing 44

3.3. Drum Cartridge Replacing 51

4. Operation and Menu Structure 59

4.1. Attaching the Printer to a Computer 59

4.2. Turning on the Printer 59

4.3. Control Panel View 61

4.4. Function of the Control Panel Elements 62

4.5. Configuration via the Control Panel 64

4.6. Menu Structure 65

4.7. Syntax of Diagrams 70

4 Table of Contents

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Chapter Page

5. Panel Functions 71

5.1. Printing the Status Sheet 71

5.2. Printing the Font List 73

5.3. Choosing Print Resolution 74

5.4. Hexdump-Mode Activation 76

5.5. Normal Print Mode Activation (incl. FORM FEED) 77

5.6. Clearing the Input Buffer (Cancel Job) 78

5.7. Printing the Menu Page 79

5.8. Generating Testsheets (Sliding Pattern) 80

5.9. Feeder (Cassette) Selection 81

5.10. Stacker Selection 83

5.11. Print Mode Selection (Simplex/Duplex) 85

5.12. Paper Size Selection 87

5.13. Enabling Format Check 88

5.14. Print Direction Selection 89

5.15. Data - Interface Configuration 90

5.16. Emulation Selection 91

5.17. Display Language Selection 93

5.18. Transparent Code Adjustment 94

5.19. Selection of Memory Distribution (Input Buffer) 95

5.20. Setting to Factory Default 96

5.21. Font Selection 97

5.22. Text Orientation Selection 100

5.23. Symbol Code Selection 101

5.24. Configuration of Text Margins 102

5.25. Image Shifting to the X-Direction 103

5.26. Image Shifting to the Y-Direction 105

5.27. Lines per Inch Setting (Line Spacing) 107

5.28. Number of Characters per Inch Setting (Character Spacing) 108

5.29. Print Density Setting 109

5.30. Configuration of Network Parameters (IP Address, e.g.) 110

Table of Contents 5

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Chapter Page

6. Operator Maintenance 113

6.1. Printer Cleaning 113

6.1.1. Printer Cabinet Cleaning 113

6.2. Replacing the Transfer Roller and Fuser 114

7. Troubleshooting 125

7.1. Error in the Print Process 126

7.2. Reduced Print Quality 127

7.3. Error Messages 128

7.3.1. Consumables Missing 128

7.3.2. Error in Paper Transport 129

7.3.3. Service Call 129

7.4. Print Media Jam 130

7.4.1. Avoiding Jams 130

7.4.2. Clearing Jams from the Printer 132

7.4.3. Clearing Jam inside Cassette 1 and the Toner Cartridge Area 135

7.4.4. Clearing Jam inside Cassette 2 138

7.4.5. Clearing Jam inside Cassette 3 and Cassette 4 140

7.4.6. Clearing Jam inside the Multipurpose feeder 142

7.4.7. Clearing Jam inside the Duplex Unit 143

7.4.8. Solving Paper Feed Problems 145

7.5. Print Repeat after an Error 147

8. Measures for Transport and Shipping (Repacking) 149

9. Specifications 151

10. Index 155

6 Table of Contents

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Introduction 7

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

1. Introduction

1.1. General Description

The print system SOLID 50 A3 - 3 works on an electrophotographical

base employing a laser as exposure unit. The resolution of 600 dots per inch is corresponding to about 24 pixels per mm (see section 5.3: Choosing Print Resolution).

The maximum print speed is 50 pages per minute (Letter or A4).

This SOLID printer is able to process different paper qualities with a

weight from 64 to 163 g/m. Paper sizes like A3, A4 and A5 are

fed from adjustable cassettes.

The SOLID 50 A3 - 3 ships with two adjustable 500 sheets

cassettes, a multipurpose feeder and a duplex unit for automatic

front and back side printing as a standard.

A multitude of options are available:

 two additional 500 sheets cassettes

 a 3,500-sheets finisher/stacker

 a 2,000-sheets high capacity feeder

This listing of options isn’t complete – please ask your supplier for

more information. All options promote the excellent paperhandling

functionality of the SOLID 50 A3 - 3 printers.

The special advantage for SOLID-system users is based on the

integrated MICROPLEX high performance controller. The controller

prints different information, such as text, bar code, vector graphics

and TIFF images in rated speed.

The controller understands most of the current emulations and is

compatible with different types of networks.

More importantly, the MICROPLEX controller offers its own

language, known as IDOL. The IDOL emulation offers a multitude of

convenient forms management and copying functions.

The MICROPLEX printer controller has its integrated website, this

allows a printer configuration via Ethernet. See Networking

Features of MICROPLEX Printers for more information.

8 Introduction

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Fundamentals of Digital Printing

Digital information (like a form with text, a company logo and vector graphics) is transfered from the EDP - system to the

laserprinter’s input buffer in a coded manner called an “emulation“ or “page description language“. The controller

decodes information and defines letters, numbers, graphics, etc.

into bit patterns and posts them into the controller’s frame store.

This way, a copy of the future print which is generated by dots is produced. The electronically controlled laserbeam now plots this dot pattern in rows onto a rotating, light-sensitive negatively charged drum. At those drum spots impacted by the light the electronic charge is extinguished. The negatively charged toner will stick to these spots. Because similar charges repulse each other the remaining drum surface stays blank. The paper is guided past the drum, while the electrostatically charged toner particles are attracted by the paper. This process is supported by a positively charged field that is below the paper (transfer charger). When transported further, the toner particles, which are affected by heat and pressure, are combined resistantly with the paper inside the fusing unit. The drum is discharged and cleaned.

Introduction 9

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

1.2. Conventions

blue colored text

[Menu Level 1 ]

To find the requested information more quickly and to understand instructions more easily, the following symbols are used:

This symbol refers to a possible source of danger. If you do not pay attention to this information, injuries may result, the functioning of the printer could be reduced, or the device could be damaged.

This symbol refers to important hints and suggestions on using the printer. Disregarding these hints might cause problems with the printer or within the environments.

This symbol represents a key of the control panel. Such symbols will be used in this manual whenever control panel buttons must be pushed in order to activate certain functions.

Link to another chapter or a different document. By clicking the blue colored text you'll enter the concerning chapter or document.

This symbol represents messages shown in the display.

This symbol shows a shining LED (light emitting diode). The SOLID printer panel is provided with one LED.

This symbol shows a flashing LED.

This symbol will be used in this manual to show an LED that is not shining.

10 Introduction

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

1.3. CE - Conformity

The manufacturer hereby declares that the device complies with the following guidelines. 2004/108/EG (EMC directive) 2006/95/EG (Low-voltage directive)

Applied harmonized standards: EN 55022:2006 Class A (Information technology equipment - Radio disturbance characteristics – Limits and methods of measurement) EN 61000-6-2:2005 (EMC: Immunity for industrial environments)

1.4. General Safety Instructions

This device produces, employs and possibly radiates high frequency energy. Because of this, incorrect installation can disturb radio communications.

Laser Notice

This printer is certified as a Class 1 laser product (DHHS Department of Health and Human Services). The laser system and printer are designed so there is never any human access to laser radiation above a Class 1 level during normal operation, user maintenance, or prescribed service condition. All handling or procedures that differ from the ones being described in this manual are to be omitted. Disregarding might release dangerous laser radiation.

Introduction 11

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

This MICROPLEX product and its consumables are designed and tested according to strict safety standards.

By heeding the following instructions, the user is ensured safe operations:

- Please make sure your electricity source is properly grounded.

- Install the device on solid and level ground.

- Only trained staff are authorized to transport the equipment.

- Only use consumables which are specially developed for this device.

- Using improper consumables may cause a reduction of output quality or damage to the device.

- Ensure no liquids get on or into the device.

- Do not remove any cover or safety device fastened by screws.

- Do not bridge a safety device.

- Do not push anything into the ventilation apertures.

- Never carry out installations, cleanings, or maintenance operations which are not described in this manual. These operations should only be done by MICROPLEX authorized service personnel.

12 Introduction

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

In order to disconnect the printer quickly from the main power in the event of an emergency, please note the following:

- For printers connected by a plug, the power-outlet should be installed near the printer and easily within reach.

- For permanently connected printers, an easily accessible emergency power-off switch should be installed close to the printer.

- Please do not conceal the disconnect devices with the printer or other objects.

- Please follow all the instructions and hints directly attached to the device and/or described in this manual.

- To ensure optimum printer performance, only use MICROPLEX consumables.

Installation 13

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

2. Installation

2.1. Check List

First, place the printer and the accessories onto a level surface until the final location of the printer is chosen.

Please make sure that there are no transport damages and that everything is included. Damages should be reported to the supplier immediately. Carefully open the box to make sure the following contents are included:

1. SOLID 50 A3 - 3 printer

2. Drum cartridge

3. Toner cartridge

4. Power cord

5. CD containing:

 SOLID 50 A3 - 3 Operator‘s Manual  Print drivers  IDOL Manual

Please retain the original packing materials in case the printer has to be transported in the future. Use the original packing materials and adhesive fasteners to avoid damage to the internal components. (See chapter 8 Measures for Transport and Shipping (Repacking)).

14 Installation

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

2.2. Printer Unpacking

1. Open the cardboard box as shown in the following figure

and remove the top element.

Fig. 2.2.a Opening the cardboard box

CAUTION! The printer weighs approximately 48 kg (106 lbs) and requires at least two people to lift it safely.

2. Carefully take out the SOLID printer.

Fig. 2.2.b Lifting and transporting the printer safely

Installation 15

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

3. Place the printer in an acceptable atmosphere (see section 2.4:

Printer Installation).

4. Remove all the packing materials and the adhesive fasteners

(compare the following figure).

Fig. 2.2.c Removing the packing materials and adhesive fasteners

16 Installation

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Fig. 2.2.d View of a SOLID 50 A3 - 3 printer

Please retain the original packing materials in case the printer has to be transported in the future.

Multipurpose feeder

Installation 17

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

2.3. Preparing the Printer

You have unpacked your printer and chosen a location for it. Now you are ready to set up printer supplies.

Installing the Drum Cartridge

1. Pull up on the handle to open the printer side door (Door A).

2. Gently lower the door to the open position.

Fig. 2.3.a Opening the side door (door A)

18 Installation

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

3. Using the handholds located on each side, pull open the printer front door (Door F).

Note: You must open the printer side door since some of the

following working steps cannot be performed with just the printer front door opened.

Fig. 2.3.b Opening the printer’s front door (door F)

Please store the drum cartridge in its original packing until it is installed.

Extreme fluctuations of atmospheric humidity and/or temperature are not allowed. The values listed in section 2.4 need to be met.

Handholds

Door F

Installation 19

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

4. Take the new drum cartridge out of its packing. Save the plastic bag.

Do not remove the yellow tape from the drum cartridge at this point. This has to be done in step 10.

Fig. 2.3.c Unpacking the new drum cartridge

5. Turn the drum cartridge so that the handle is on top.

6. Remove the tape (on the top of the cartridge; see figure 2.3.d) and then gently pull the protective paper straight up and out of the cartridge.

20 Installation

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Fig. 2.3.d Removing the protective paper of the new drum cartridge

Do not leave the drum cartridge exposed to light for extended periods of time.

Fig. 2.3.e Hints about the drum cartridge

Protective paper

Tape

Installation 21

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

7. Holding the new drum cartridge by the handle and one end, align the cartridge with the slots inside the printer and slide the drum cartridge halfway in.

Fig. 2.3.f Inserting the guides of the new drum cartridge

8. Drop the handle back into place.

9. Push the drum cartridge into the printer until the cartridge clicks into place.

New drum cartridge

22 Installation

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Fig. 2.3.g Inserting the new drum cartridge

10. Carefully pull the yellow tape completely out of the cartridge.

Discard the tape.

Fig. 2.3.h Removing the yellow tape

Installation 23

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Installing the Toner Cartridge

1. Take the new toner cartridge out of its packing.

Fig. 2.3.i Taking the new toner cartridge out of its packing

2. Turn the cartridge so that the handle is on top.

3. Shake the cartridge vigorously in all directions (as shown in figure 2.3.j) to distribute the toner .

If toner spills on the floor, do not clean it up using a vacuum or a wet cloth. Wipe up the spill with a dry cloth. If toner gets on clothing, be sure to wash the clothing in cold water.

Fig. 2.3.j Shaking the toner cartridge

4. Holding the new toner cartridge by the handle and one end, align the cartridge with the slots inside the printer and slide the toner cartridge halfway in.

24 Installation

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Fig. 2.3.k Inserting the guides of the new toner cartridge

5. Push the toner cartridge into the printer until the cartridge clicks into place.

Fig. 2.3.l Inserting the new toner cartridge

New toner cartridge

Installation 25

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

6. Close the printer side door (Door A).

Fig. 2.3.m Closing the printers side door (door A)

7. Hold both sides of the printer front door (Door F) and close it.

Fig. 2.3.n Closing the printers front door (door F)

Handholds

Door F

26 Installation

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

2.4. Printer Installation

- The chosen location should be clean, dry and well-ventilated.

- Damaging environmental factors such as metal vapors, oil mist,

corrosive leaches or the like must not affect the printer.

- Place the printer on a horizontal, firm and solid surface.

- The printer environment has to be free of shocks or

vibrations.

- The printer and socket have to be easily accessible.

- The printer should not be located near volatile or combustible

materials (e.g. a curtain).

- To avoid damage, the devices must be switched off (e.g. cut off

from the power supply) before the user begins connecting the interface lines.

- The printer must be connected to an appropriate AC power

source 120V AC/60 Hz (North America) or 230V/50 Hz (Europe, United Kingdom e.g.). The power source must be properly grounded. The socket and power cords must not be damaged.

- Use the printer only within the allowed fluctuation range of

± 10%.

- The power source must be free of noise, and not subjected to

surges or noise (e.g. generated by big machines).

Installation 27

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

If you’re going to move or transport the printer, keep the

following in mind:

- Because the printer is heavy (approximately 48 kg [106 lbs]),

two people are required to lift it safely.

- Remove the toner cartridge and the drum cartridge before you

move or transport the printer! If the printer is moved with the two cartridges installed, toner may spill out and damage the printer.

- Be sure to plug the printer into a properly grounded outlet in

the new location.

28 Installation

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

- Please note the following environment conditions are needed

to operate the printer at full capacity:

Temperature: +5°C (41°F) to +32°C (90°F) Relative atmospheric humidity: 15% to 85%

- Do not expose the printer to abrupt temperature changes

(heating, window or air conditioning).

- The printer should not be exposed to direct sunlight.

- Required space:

Fig. 2.4.a Required space for the SOLID 50 A3 - 3 (printer with optional cassette 3+4)

Installation 29

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

- Required space (continuation):

Fig. 2.4.b Required space for a printer SOLID 50 A3 - 3 with options

- in this example: Printer equipped with a high capacity feeder and a finisher /stacker

30 Installation

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

2.5. Printer Components

Fig. 2.5.a Printer Components

Cassette 2

Cassette 1

Control panel

Power switch

Front cover (Door F)

Jam access door (Door A)

Multipurpose feeder

Standard output bin

Duplex unit

Cassette 3 (option)

Cassette 4 (option)

Installation 31

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Fig. 2.5.b View on the interfaces

Ethernet interface

USB interface

Serial interface

Centronics interface

Flap Control panel

Power switch

32 Handling of Consumables

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

3. Handling of Consumables

3.1. Print Media Handling (Paper, e.g.)

The printer processes the sizes A3, A4, A4R, A5, A5R, Ledger, Letter, LetterR and Legal (see table in section 3.1.4) with paper weights from 64 to 163 g/m².

Paper jams can be avoided by accurately and carefully filling the paper cassettes. Please do not open or remove a paper cassette while the printer is running.

Please notice the specifications about the paper’s print-side (see the information on the paper packing).

If an empty paper cassette has to be refilled (without changing the paper size, compare section 3.1.4) do the following:

3.1.1. Loading Cassettes 1 and 2

Your SOLID 50 A3 - 3 has two standard cassettes (cassettes 1 and 2). They can each hold 500 sheets of plain paper.

1. Pull the cassette open until it stops.

Handling of Consumables 33

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Fig. 3.1.1.a Opening the cassette

2. Press the levers of the side guide (compare the small “picture” in the

upper part of the following figure) and move the side guide to the right.

Fig. 3.1.1.b Moving the paper guides

3. Press the levers of the front guide (compare the small “picture” in

34 Handling of Consumables

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

the right part of the figure above) and slide this guide to the front side of the cassette.

Note: You’ll find labels with print media size information in the

cassettes.

4. Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the print media.

Fig. 3.1.1.c Fanning and aligning the paper pile

5. Straighten the edges of the stack on a level surface.

6. Now put your stack of print media into the cassette as shown in the

following figure.

Fig. 3.1.1.d Inserting print media

Handling of Consumables 35

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Do not exceed the maximum stack height indicated on the back guide. Overfilling the cassette may cause paper jams.

Fig. 3.1.1.e Filling level for the cassette

Do not load bent or wrinkled print media.

7. Press the levers of the front guide (see next figure) and slide the guide until it lightly touches the stack of print media.

Maximum stack height indicator

36 Handling of Consumables

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Fig. 3.1.1.f Sliding the front guide to the print media stack

8. Press the levers of the side guide and slide it to the left until it lightly touches the stack of print media. Make sure the guide locks into place.

Fig. 3.1.1.g Sliding the side guide to the print media stack

Handling of Consumables 37

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

9. Slide the cassette all the way into the printer. If the cassette is not pushed completely into the printer, text and images may print in the wrong position on the page, and the margins may appear incorrect, or you may receive an error message.

Fig. 3.1.1.h Sliding the cassette into the printer

38 Handling of Consumables

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

3.1.2. Loading the Multipurpose Feeder

The multipurpose feeder comes standard with the printer and holds approximately 100 sheets of 20 lb paper.

1. Open the multipurpose feeder.

Fig. 3.1.2.a Opening the multipurpose feeder

2. “Open” the paper guides for the print media to be used. (Slide the paper guides to the edges of the multipurpose feeder.)

3. Adjust the extension guide to the length of the print media to be used.

4. Flex the sheets back and forth to loosen them, and then fan them.

Fig. 3.1.2.b Fanning and aligning the paper pile

Handling of Consumables 39

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

5. Straighten the edges of the stack on a level surface.

Do not load bent or wrinkled print media.

6. Orient the stack of print media correctly for the size, type, and print method you are using. Refer to the icons on the feeder.

Do not exceed the maximum stack height indicated on the paper guide. Overfilling the feeder may cause paper jams.

Fig. 3.1.2.c Mark for the maximum stack height

7. Place the print media along the front side of the multipurpose feeder and push it in as far as it will go.

Do not force the print media.

8. Slide the guides towards the stack (see the following figure) until they lightly touch the stack of print media.

40 Handling of Consumables

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Fig. 3.1.2.d Sliding the guides to the print media stack

9. When finished printing from the multipurpose feeder, remove any print media, push the extension guide back in, and push the feeder to the closed position.

Handling of Consumables 41

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

3.1.3. Using the Output Bins

The printer has one standard bin, which holds up to 500 sheets of print media that exit face down.

Fig. 3.1.3.a Standard output bin of the printer

As an option a 3,500 sheets finisher/stacker and a face-up stacker (100 sheets) are available for your SOLID 50 A3 – 2 printer.

Standard output bin

42 Handling of Consumables

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

3.1.4. Changing the Paper Size Setting

Depending on the print material you use, you may need to change the Paper Size setting.

The following table shows the paper sizes supported by the paper cassettes:

Cassette / Feeder

Paper sizes supported

Print media supported

Capacity

A3

A4

A4R

A5

*1)

A5R

*2)

Ledger

Letter

LetterR

Legal

Multipurpose feeder

Yes

Paper, transparencies, labels, card stock

appr. 100 sheets of 20 lb paper

1

2

3 and 4

(2 TT)

3 and 4

(Tandem TT)

Yes

No

Yes

No

Yes

No

Yes

No

Yes

No

Yes

No

Yes

No

Paper, transparencies

500 Sheets

of 20 lb paper

500+500 Sheets

1200+800 Sheets

*1)

A5 = Long Edge Feed

*2)

A5R = Short Edge Feed

To change the size of the print page (print image) use the panel function Paper Size Selection (see section 5.12).

Feed

Handling of Consumables 43

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

The printer is able recognize the paper size of the print media in the paper feeders (cassettes). The printer automatically detects the positions of the paper guides for this.

Please set the paper guides of the feeders (cassettes) to the exact size of your paper (notice the markings).

Further information can be found in section 3.1.1 Loading Paper to the Printer Cassettes.

You can use the panel function Enabling Format Check (see section 5.13) to enable or disable automatic format check of the printer.

If there is no paper with appropriate size in any paper cassette, an error message like the following example is displayed on the panel:

[Format Error ] [DIN A5 missing ]

Non Standard paper sizes (user defined formats) have to be set using the panel functions Page Length and Paper Width (compare section 4.6 Menu structure).

44 Handling of Consumables

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

3.2. Toner Cartridge Replacing

Replace the toner cartridge as soon as the message [Toner empty! ] is displayed. On average 30,000 letter-size pages can be printed with one toner cartridge. (This depends on the print density. In this example, a print density of 5% was considered).

Warning: We do not recommend refilling used toner cartridges or purchasing refilled cartridges from a third party. Print quality and printer reliability cannot be guaranteed if you do. The printer warranty does not cover damage caused by using refilled cartridges.

Please store the toner cartridge in its original packing until it is installed.

Extreme fluctuations of atmospheric humidity and/or temperature are not allowed. The values listed in section 2.4 need to be met.

In order to replace the toner cartridge, follow these instructions:

Notice the information used with the toner cartridge also.

Handling of Consumables 45

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

1. Switch off the printer.

2. Pull up on the handle to open the printer side door (Door A). Gently lower the door to the open position.

Fig. 3.2.a Opening the side door (door A)

3. Using the handholds located on each side, pull open the printer front door (Door F).

Note: You must open the printer side door since the toner

cartridge cannot be removed with just the printer front door opened.

46 Handling of Consumables

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Fig. 3.2.b Opening printer’s front door (door F)

4. Pull up on the latch to release and slide the toner cartridge out until you see the handle.

Fig. 3.2.c Taking out the toner cartridge

Toner cartridge

Handholds

Door F

Handle

Handling of Consumables 47

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

5. Use the handle to pull the old toner cartridge straight out, and place it on a suitable site.

6. Clean the printer (see chapter 6).

7. Take the new toner cartridge out of its packing.

Fig. 3.2.d Taking the new toner cartridge out of its packing

8. Turn the cartridge so that the handle is on top.

9. Shake the cartridge vigorously in all directions (as shown in figure 3.2.e) to distribute the toner.

If toner spills on the floor, do not clean it up using a vacuum or a wet cloth. Wipe up the spill with a dry cloth. If toner gets on clothing, be sure to wash the clothing in cold water.

48 Handling of Consumables

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Fig. 3.2.e Shaking the toner cartridge

10. Holding the new toner cartridge by the handle and one end,

align the cartridge with the slots inside the printer and slide the toner cartridge halfway in.

Fig. 3.2.f Inserting the guides of the new toner cartridge

11. Push the toner cartridge into the printer until the cartridge clicks

into place.

New toner cartridge

Handling of Consumables 49

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Fig. 3.2.g Inserting the new toner cartridge

12. Close the printer side door (Door A).

13. Hold both sides of the printer front door (Door F) and close it.

14. Place the used toner cartridge in the plastic bag you saved in

step 7.

Fig. 3.2.h Use the plastic bag for the old toner cartridge

50 Handling of Consumables

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

15. Please pay attention to the information about the disposal of the

old toner cartridge (current information can be found on the new toner cartridge).

By returning the used toner cartridge to MICROPLEX, you help support world-wide recycling efforts. Until disposal, keep the old toner cartridge inside a closed cardboard box.

Handling of Consumables 51

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

3.3. Drum Cartridge Replacing

On average 60,000 letter-size pages can be printed with one drum cartridge.

Please store the drum cartridge in its original packing until it is installed.

Extreme fluctuations of atmospheric humidity and/or temperature are not allowed. The values listed in section 2.4 need to be met.

In order to replace the drum cartridge, follow these instructions:

Notice the information used with the drum cartridge also.

52 Handling of Consumables

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

1. Switch off the printer.

2. Pull up on the handle to open the printer side door (Door A).

3. Gently lower the door to the open position.

Fig. 3.3.a Opening the side door (door A)

4. Using the handholds located on each side, pull open the printer front door (Door F).

Note: You must open the printer side door since the drum

cartridge cannot be removed with just the printer front door opened.

Handling of Consumables 53

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Fig. 3.3.b Opening the printer’s front door (door F)

5. Pull up on the latch to release and slide the drum cartridge out until you see the handle.

Fig. 3.3.c Taking out the drum cartridge

Drum cartridge

Handholds

Door F

Handle

54 Handling of Consumables

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

6. Use the handle to pull the drum cartridge straight out, and place it on a suitable site.

7. Clean the printer (see chapter 6).

8. Take the new drum cartridge out of its packing and place it in an acceptable atmosphere. Save the plastic bag.

Do not remove the yellow tape from the drum cartridge at this point. This has to be done in step 14.

Fig. 3.3.d Unpacking the new drum cartridge

Handling of Consumables 55

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

9. Turn the cartridge so that the handle is on top.

10. Remove the tape (on the top of the cartridge; see the following figure) and then gently pull the protective paper straight up and out of the cartridge.

Fig. 3.3.e Removing the protective paper of the new drum cartridge

Do not leave the drum cartridge exposed to light for extended periods of time.

Fig. 3.3.f Hints about the drum cartridge

Protective paper

Tape

56 Handling of Consumables

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

11. Holding the new drum cartridge by the handle and one end, align the cartridge with the slots inside the printer and slide the drum cartridge halfway in.

Fig. 3.3.g Inserting the guides of the new drum cartridge

12. Drop the handle back into place.

13. Push the drum cartridge into the printer until the cartridge clicks into place.

New drum cartridge

Handling of Consumables 57

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Fig. 3.3.h Inserting the new drum cartridge

14. Carefully pull the yellow tape completely out of the cartridge. Discard the tape.

Fig. 3.3.i Removing the yellow tape

15. Close the printer side door (Door A).

58 Handling of Consumables

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

16. Hold both sides of the printer front door (Door F) and close it.

17. Place the used drum cartridge in the plastic bag you saved in step 9.

Fig. 3.3.j Use the plastic bag for the old drum cartridge

18. Please pay attention to the information about the disposal of the

old drum cartridge (current information can be found on the new drum cartridge).

By returning the used drum cartridge to MICROPLEX, you help support world-wide recycling efforts. Until disposal, keep the old drum cartridge inside a closed cardboard box.

Operation and Menu Structure 59

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

4. Operation and Menu Structure

4.1. Attaching the Printer to a Computer

1. Make sure the printer, computer, and any other attached devices

are turned off and unplugged.

2. Use a proper interface line to connect the printer to the computer or to attach the printer to the network. The printer SOLID 50 A3 - 3 is provided with several interfaces; see figure 2.5.b and chapter 9 Specifications for more information.

4.2. Turning on the Printer

1. Plug one end of the printer power cord into the socket at the back of the

printer and the other end into a properly grounded outlet.

Fig. 4.2.a Connect Power

Power socket

60 Operation and Menu Structure

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Fig. 4.2.b Turning on the printer

2. Turn on the printer.

The printer requires time to warm up after you turn it on. During this period, the message [Please Wait ] appears on the control panel display. After the printer completes its internal tests, the [SOLID 50 A3 - 3 ] message indicates the printer is ready to receive jobs. If you see other messages on the display, refer to chapter Troubleshooting for instructions on clearing the message.

Note: You can change the language that appears on the control panel

display. Use the Display Language Selection panel function (see section 5.17).

Power switch

Operation and Menu Structure 61

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

4.3. Control Panel View

Display (two-lined)

ONLINE SOLID 50 A3 - 3

LEDs 9 Keys

LED integrated

62 Operation and Menu Structure

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

4.4. Function of the Control Panel Elements

Display

The display (panel) serves to show the printer’s status messages.

ON LINE - LED (integrated in the START/STOP key)

The printer is ready to receive data from the host (the printer is ON LINE).

The printer is not ready to receive data from the host (OFF LINE). The control panel keys are active.

DATA - LED

ACTIVE

The printer receives printable data.

The printer’s input buffer contains printable data and the controller waits

for further data.

There are no printable data in the input buffer.

ERROR - LED

FAULT

An error occurred in the printer. The printer is OFF LINE.

No error occurring.

Operation and Menu Structure 63

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Panel keys

This key is used to start the printing of a status sheet. (As an alternative the panel function Printing the Status Sheet can be used).

The MENU key is used to get into the next (higher) level of the menu structure. As an alternative the RETURN key can be used as well.

Using this key confirms inputs and releases functions. As an alternative the SELECT key can be used as well.

The START/STOP key turns the printer ON- / OFF LINE.

These keys are used for working within the different levels of the menu structure. This structure and the panel functions are described in the following.

Using this key a RESET is released in the OFF LINE mode. You can back out e.g. error messages by a RESET.

64 Operation and Menu Structure

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

4.5. Configuration via the Control Panel

You can use the control panel to change the printer configuration and customize your printer to meet your specific needs.

In addition printer configuration via Ethernet is possible. The MICROPLEX printer controller offers an integrated website, for more information see Networking Features of MICROPLEX Printers.

Chapter 5 (Panel Functions) describes how to reach the particular printer functions via the control panel.

T e m p o r a r y changes in printer configuration are effective only as long as the printer stays turned on. To select such changes temporarily, the user must terminate the change of function by pressing the SELECT* key one single time.

P e r m a n e n t changes in printer configuration are active each time the printer is turned on again. To select such changes permanently, the user must terminate the change of function by pressing the SELECT* key two times.

An output of the current printer values can be generated using the panel function Printing the Status Sheet  (see section 5.1).

Please note:

 User default settings remain in effect until you save new settings

or restore the factory defaults.

 Settings you choose from your software application or printer

driver can also change or override the user default settings you select from the operator panel.

* As an alternative the key INFO can be used as well.

Operation and Menu Structure 65

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

4.6. Menu Structure

Access to the menu structure is possible as soon as the printer is turned OFF LINE. The menu structure of the SOLID 50 A3 - 3 is arranged in different levels:

Menu Level 1

Status Sheet

Hexdump

Normal Print/FF

Cancel Job

Menu Page

Sliding Pattern

Buffer-Dump

Paper Menu

Paper Size

Feeder Select

Manual Feed

Auto.Sel. 1+2

Auto.Sel.Mode

Simpl. / Dupl.

Simplex

Two-Up Mode

Configuration

Interface

SIA Timeout

RS 232

RS 232 Protocol

RTS/CTS

XON/XOFF

Baudrate

RS 232 Fm.

Emulation

Language

Input Buffer

Transparent Code

Config. Word

User Config.

Select

Define

Factory Default

Page Menu

Font Number

Orientation

Margin

Left

from Right

Top

from Bottom

Engine

Image Y-Pos.

Resolution

Feeder

Y-Direction

Print Direct.

X-Direction

Line Termination

ON LINE - Mode

OFF LINE



Duplex Mode

Line Spacing

Symbol Code

Key lock

Time Setting

Date Setting

Char. Spacing

Image X-Pos.

Stacker Select

Network

Font List

Extended Menu

Pow.Sav.Time

Paper Type

Paper Width *

Page Length

in mm

in Inch

in mm

in Inch

in 1/300 Inch

None

RFM

Service Mode

File-Management

Acoustic Signals

Key Tone

Error Tone

Fmt.Chk.Man.Feed

Format Check

Density

Print-Files

Directory

PCL Y-Offset

NumberOfCopies

Pattern Test

Standard Size

Last Error

Dot-Test

. . .

DHCP

Manual

Off

IP Address

Subnet Mask

Gateway

IP Assign

10MB HalfDuplex

10MB FullDuplex

Autonegotiation

Duplex/Speed

100MB HalfDuplex

100MB FullDuplex

Timeout

Persistent DHCP

SNMP

Ethernet

This panel function allows the user to choose a reduced menu instead of the extended menu shown above.

66 Operation and Menu Structure

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Selecting positions in the menu structure:

["Menu Level"]

["Function"]

This symbol shows the START/STOP key. You get automatically into menu level 1, if the printer is turned OFF LINE with this key.

By pressing the NEXT key or the PREVIOUS key you can move within the menu levels.

Each menu item/subitem within a menu level is shown in the display.

The SELECT key has two main functions. It gives the user access to a particular menu and, once in the menu, it allows the user to select a particular function.

As an alternative the INFO key can be used as well.

Operation and Menu Structure 67

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Functions / Changing of function values:

Within one function the value can be changed by pressing the NEXT key or the PREVIOUS key. In case of a multi-digit function value the value of the currently chosen digit will be changed.

In case of a multi-digit function value pressing the SELECT key switches to the next position of the function value. Pressing the RETURN key switches to the previous digit of the function value.

Please note: If you press the RETURN key although the absolute left

digit of the function value is still arrived, the changing procedure will be cancelled and this moves you to the next menu level above.

If you press the SELECT key although the absolute right

digit (digit 1) of the function value is still arrived, the currently displayed function value is stored.

68 Operation and Menu Structure

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

[Save as Setup?]

Pressing the INFO key the displayed function value is confirmed respectively the displayed function is activated. (As an alternative the SELECT key can be used as well; compare description above.) The changes are saved temporay. (This means, the changes are saved only until the next printer power off).

After this you have to decide, if you want to save the changes permanent (Save as setup).

To select such changes permanently, the user must press the INFO key or the SELECT key one more time. These permanent changes in printer configuration are active each time the printer is turned on again.

If the MENU key is pressed instead, the changes are only stored temporary (not saved as setup). (This key takes the user to the respective previous menu level).

Operation and Menu Structure 69

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Return to the menu level above:

Pressing the RETURN key or the MENU key takes the user back to the respective menu level above.

Return to the ON LINE - mode:

Pressing the START/STOP key switches the user directly to ON LINE from any menu position.

70 Operation and Menu Structure

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

4.7. Syntax of Diagrams

["Message"]

The control panel functions will be described using diagrams. These diagrams show the course necessary in order to activate a certain function.

First the elements of the diagrams are explained:

The sequence on the left describes which keys have to be pressed briefly in succession.

In this example the START/STOP key has to be pressed first. Then the START/STOP key has to be released and the NEXT key has to be pressed. Then the NEXT key has to be released and the SELECT key has to be pressed.

The Panel display column shows the display messages corresponding to the sequences listed on the left.

In the column Notes explanations to particular operational steps are given.

Panel Functions 71

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

5. Panel Functions

For the panel functions described in the following text, the printer is presumed to be switched on and in the ON LINE-mode.

5.1. Printing the Status Sheet

This function generates a status sheet. The status sheet contains information about the current printer configuration, the available fonts and options.

Panel display

[SOLID 50 A3 - 3 ]

[Menu Level 1 ]

[Status Sheet ]

Notes

Turn the printer OFF LINE with this key.

Press the SELECT key. Menu Level 1 is selected.

Press the SELECT key again.

A status sheet is printed.

The printer is turned ON LINE again.

72 Panel Functions

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Status sheet contents:

-

The first lines, entitled SERVICE INFORMATION, contain hexadecimal coded configuration parameters.

Printed in plain text:

Controller version / memory / serial number Firmware release Interface parameters of Parallel, Serial, USB, Network (Ethernet) Network parameters and addresses Printer emulation User-RAM / free User-RAM Input data buffer Transparent code Paper size Default margins top / left bottom / right Default character code Options Fonts installed (Font banks)

Note: Use the panel function Printing the Font List to show the fonts installed

(see the following section).

Panel Functions 73

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

5.2. Printing the Font List

This function generates a list of all fonts installed to the printer. The font list shows demo prints of all fonts and, in addition, the concerning PCL selection commands. These commands contain information on font width and font hight (see section 5.21 Font Selection, too).

Panel display

[SOLID 50 A3 - 3 ]

[Menu Level 1 ]

[Status Sheet ]

  

[Font List ]

Notes

Turn the printer OFF LINE with this key.

Menu Level 1 is selected.

Press the NEXT or PREVIOUS key until [Font List ] is displayed.

The font list is printed.

The printer is turned ON LINE again.

74 Panel Functions

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

5.3. Choosing Print Resolution

This function allows the user to choose the current print resolution. If, after a particular resolution is chosen, the print data stream indicates a different resolution (e.g. via a WINDOWS print driver), the second print resolution will be used only for that job.

Panel display

[SOLID 50 A3 - 3 ]

[Menu Level 1 ]

  

[Engine]

[Resolution]

[300 dpi ]

  

[600 dpi ]

[Save as Setup? ]

Notes

Turn the printer OFF LINE with this key.

Press the NEXT or PREVIOUS key until [Engine ] is displayed.

Menu item Engine is selected.

Menu item Resolution is selected.

Press the NEXT or PREVIOUS key until the desired resolution (e.g. 600 dots per inch) is displayed.

600 dpi resolution is selected.

In addition this new value can be saved as setup value (using the SELECT key), before the printer is turned ON LINE again.

Panel Functions 75

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Remarks on choosing print resolution (Fonts):

By selecting 300 dpi resolution the printing system will be compatible for all applications (300 dpi data stream), also the 300 dpi font banks (bitmap writing) are available.

If 600 dpi resolution is chosen, the corresponding fonts must be loaded into the printer server (e.g. True Type fonts, scalable download fonts).

76 Panel Functions

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

5.4. Hexdump-Mode Activation

In the Hexdump-Mode the printer prints all characters received via interface without any interpretation (hexadecimal coded). This mode helps with error diagnosis. The Hexdump-Mode can be activated only temporarily.

Panel display

[SOLID 50 A3 - 3 ]

[Menu Level 1 ]

[Status Sheet ]

  

[Hexdump ]

Notes

Turn the printer OFF LINE with this key.

Menu Level 1 is selected.

Press the NEXT or PREVIOUS key until [Hexdump] is displayed.

The Hexdump-Mode is activated.

The printer is turned ON LINE again.

Note:

By activating the normal print mode (see next page) or by turning the printer off and on again the printer can be taken out of Hexdump-Mode. Time between turning the printer off and on again should be at least 15 seconds.

Panel Functions 77

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

5.5. Normal Print Mode Activation (incl. FORM FEED)

The normal print mode suspends the Hexdump-Mode. This function is activated, when a print job must be continued without turning the printer off and on again. In addition to that the function “Normal Print Mode Activation“ is used to produce a FORM FEED.

Panel display

[SOLID 50 A3 - 3 ]

[Menu Level 1 ]

[Status Sheet ]

  

[Normal Print /FF]

[Normal Print/FF ]

Notes

Turn the printer OFF LINE with this key.

Menu Level 1 is selected.

Press the NEXT or PREVIOUS key until [Normal Print/FF ] is displayed.

The normal print mode is activated.

The printer is turned ON LINE again.

Note:

After activating the normal print mode a FORM FEED is released automatically and one sheet is put out. This is necessary because after a test in the Hexdump-Mode it is possible that data can remain in the input buffer unintentionally (cause: in the HexdumpMode no control characters are evaluated and no FORM FEED is effected).

78 Panel Functions

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

5.6. Clearing the Input Buffer (Cancel Job)

This function permits the resumption of a print job at a particular page after a print interruption (e.g. paper jam). The data contained in the input buffer before the interruption are cleared.

Panel display

[SOLID 50 A3 - 3 ]

[Menu Level 1 ]

[Status Sheet ]

  

[Cancel Job ]

Notes

Turn the printer OFF LINE with this key.

Menu Level 1 is selected.

Press the NEXT or PREVIOUS key until [Cancel Job ] is displayed.

All data contained in the input buffer will be cleared.

The printer is turned ON LINE again.

Panel Functions 79

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

5.7. Printing the Menu Page

This function prints a survey of the available panel functions. Note: When printing the menu page please use a large paper.

Panel display

[SOLID 50 A3 - 3 ]

[Menu Level 1 ]

[Status Sheet ]

  

[Menu Page ]

Notes

Turn the printer OFF LINE with this key.

Menu Level 1 is selected.

Press the NEXT or PREVIOUS key until [Menu Page] is displayed.

A menu structure presentation of the SOLID 50 A3 - 3 (see section 4.6) is printed.

The printer is turned ON LINE again.

80 Panel Functions

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

5.8. Generating Testsheets (Sliding Pattern)

This function generates a series of test prints without sending data to the printer. These test prints facilitate error analysis.

Panel display

[SOLID 50 A3 - 3 ]

[Menu Level 1 ]

[Status Sheet ]

  

[Sliding Pattern ]

Notes

Turn the printer OFF LINE with this key.

Menu Level 1 is selected.

Press the NEXT or PREVIOUS key until [Sliding Pattern] is displayed.

A series of test prints is generated.

The printer is turned ON LINE again.

The printing out of test prints can be stopped by pressing the START/STOP key.

Panel Functions 81

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

5.9. Feeder (Cassette) Selection

This function enables the user to choose a particular feeder (cassette).

Note: If automatic format check is enabled (see section 5.13), the current

paper size has priority. The paper size selection overrides the feeder selection (compare section 5.12: Paper Size Selection). In addition this feeder selection is suspended by feeder selections via the data stream (feeder selections via the application software or printer driver override the settings made at the panel of the printer).

Panel display

[SOLID 50 A3 - 3 ]

[Menu Level 1 ]

  

[Paper Menu ]

[Feeder Select]

[Feeder 1 ]

  

[Feeder 2 ]

[Save as Setup? ]

Notes

Turn the printer OFF LINE with this key.

Press the NEXT or PREVIOUS key until [Paper Menu] is displayed.

Menu item Feeder Select is chosen.

Feeder 1 = currently adjusted default.

Press the NEXT or PREVIOUS key until the desired feeder is displayed.

Feeder 2 (Cassette 2) is selected.

In addition this new value can be saved as setup value (using the SELECT key), before the printer is turned ON LINE again.

82 Panel Functions

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Feeder assignment:

Manual Feed Multipurpose Feeder

Feeder 1 Upper Feeder (Cassette 1)

Feeder 2 Lower Feeder (Cassette 2)

(The SOLID 50 A3-3 comes with cassette 1 and 2 (extent of supply). The third and fourth cassettes are optional. Compare section 2.5 Printer Components.)

. . .

Auto. 2+1 Automatic selection between feeders (the subset of feeders is settable, tray 1+2 = default)

Auto.Sel. Mode Automatic selection between all feeders that are installed (Feeder Linking)

Panel Functions 83

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

5.10. Stacker Selection

This function enables the user to choose a particular stacker.

Panel display

[SOLID 50 A3 - 3 ]

[Menu Level 1 ]

  

[Paper Menu ]

[Feeder Select]

  

[Stacker Select]

[Paper Tray 1 ]

  

[Paper Tray 2 ]

[Save as Setup? ]

Notes

Turn the printer OFF LINE with this key.

Press the NEXT or PREVIOUS key until [Paper Menu] is displayed.

Press the NEXT or PREVIOUS key until [Stacker Select ] is displayed.

Paper Tray 1 = Current default.

Press the NEXT or PREVIOUS key until the selected Paper Tray (e.g. Paper Tray 2) is displayed.

Paper Tray 2 is selected.

In addition this new value can be saved as setup value (using the SELECT key), before the printer is turned ON LINE again.

84 Panel Functions

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Stacker assignment:

Paper Tray 1 Standard output bin (face down tray)

Paper Tray 2 Second output bin (optional finisher/stacker)

Paper Tray 3 Third output bin (optional finisher/stacker)

Panel Functions 85

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

5.11. Print Mode Selection (Simplex/Duplex)

This function allows the user to choose between simplex and duplex printing (via the duplex unit). (Simplex = one-sided printing, Duplex = double-sided printing).

Panel display

[SOLID 50 A3 - 3 ]

[Menu Level 1 ]

  

[Paper Menu ]

[Feeder Select ]

  

[Simpl. / Dupl. ]

[Simplex ]

  

[Duplex Mode 1 ]

[Save as Setup? ]

Notes

Turn the printer OFF LINE with this key.

Press the NEXT or PREVIOUS key until [Paper Menu ] is displayed.

Press the NEXT or PREVIOUS key until [Simpl. / Dupl. ] is displayed.

Press the NEXT or PREVIOUS key until the desired print mode is displayed.

The duplex mode 1 is selected.

In addition this new value can be saved as setup value (using the SELECT key), before the printer is turned ON LINE again.

86 Panel Functions

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Information about the Print Mode command:

This command switches „intelligent“ printing on the front and rear

side of a page on and off.

Duplex Mode Description

0 Switches duplex print mode off

1 Duplex print mode

long format-side, with rear side displacement

2 Duplex print mode short format-side, without rear side displacement

3 Duplex print mode

long format-side, without rear side displacement for preprinted paper

4 Duplex print mode

short format-side, without rear side displacement for preprinted paper

5 Duplex print mode long format-side, without rear side displacement

Panel Functions 87

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

5.12. Paper Size Selection

This function selects the size of the print page (print image). Note: In addition this feeder selection is suspended by feeder selections via

the data stream (feeder selections via the application software or printer driver override the settings made at the panel of the printer).

Panel display

[SOLID 50 A3 - 3 ]

[Menu Level 1 ]

  

[Paper Menu ]

[Feeder Select ]

  

[Paper Size ]

[Standard Size ]

[Letter ]

  

[Legal ]

[Save as Setup? ]

Notes

Turn the printer OFF LINE with this key.

Press the NEXT or PREVIOUS key until [Paper Menu] is displayed.

Press the NEXT or PREVIOUS key until [Paper Size ] is displayed.

Press the SELECT key. After this you can choose from a selection of Standard Sizes. (Use the menu items Page Length and Paper Width to set a non-standard size (Special Size)).

Letter = currently adjusted default.

Press the NEXT or PREVIOUS key until the selected paper size (e.g. Legal) is displayed.

The paper size Legal is selected.

In addition this new value can be saved as setup value (using the SELECT key), before the printer is turned ON LINE again.

88 Panel Functions

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

5.13. Enabling Format Check

This function is used to enable or disable automatic format check of the printer. If format check is active, the MPC identifies format commands in the data stream and prevents for example printing on undersized paper.

Hint: If format check is disabled, every feeder selection / cassette selection is carried

out (even if the paper in the selected feeder is too small for the print image).

Note: For the multipurpose feeder the separate panel function [Fmt.Chk.Man.Feed ] has to be used in the same manner.

Panel display

[SOLID 50 A3 - 3 ]

[Menu Level 1 ]

  

[Engine ]

[Resolution ]

  

[Format Check ]

[Off ]

  

[On ]

[Save as Setup? ]

Notes

Turn the printer OFF LINE with this key.

Press the NEXT or PREVIOUS key until [Engine ] is displayed.

Press the NEXT or PREVIOUS key until [Format Check ] is displayed.

Press the NEXT or PREVIOUS key until [On ] is displayed.

The format check is enabled.

In addition this new value can be saved as setup value (using the SELECT key), before the printer is turned ON LINE again.

Panel Functions 89

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

5.14. Print Direction Selection

This function selects the active print orientation (orientation of the whole printout including graphics, etc. on the paper).

Panel display

[SOLID 50 A3 - 3 ]

[Menu Level 1 ]

   [Paper Menu ]

[Feeder Select ]

  

[Print Direct. ]

[Print Direct. 0 ]

  

[Print Direct. 1 ]

[Save as Setup? ]

Notes

Turn the printer OFF LINE with this key.

Press the NEXT or PREVIOUS key until [Paper Menu ] is displayed.

Press the NEXT or PREVIOUS key until [Print Direct. ] is displayed.

Press the NEXT or PREVIOUS key until the desired print direction is displayed.

The print direction 1 = landscape is selected.

In addition this new value can be saved as setup value (using the SELECT key), before the printer is turned ON LINE again.

Print direction assignment:

Print direction 0 = Portrait (upright format) Print direction 1 = Landscape (horizontal format) Print direction 2 = Portrait upside down Print direction 3 = Landscape upside down

90 Panel Functions

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

5.15. Data - Interface Configuration

This function is used to set the interface parameters.

Panel display

[SOLID 50 A3 - 3 ]

[Menu Level 1 ]

   [Configuration ]

[Interface ]

[SIA Timeout ]

[ 30 s ]

   [ 40 s ]

[Save as Setup? ]

Notes

Turn the printer OFF LINE with this key.

Press the NEXT or PREVIOUS key until [Configuration ] is displayed.

Press the SELECT key to change the timeout.

The currently set value for he timeout is displayed (here: 30 seconds).

Pressing the NEXT or PREVIOUS key changes the timeout

The timeout (the waiting period for SIA to switch to the next interface) is increased to 40 seconds.

In addition this new value can be saved as setup value (using the SELECT key), before the printer is turned ON LINE again.

Note:

The printer uses SIA (Simultaneous Interface Administration) to check, which interface is currently used for the transfer of print data.

Panel Functions 91

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

5.16. Emulation Selection

This function helps to determine which printer emulation will be activated.

Panel display

[SOLID 50 A3 - 3 ]

[Menu Level 1 ]

  

[Configuration ]

[Interface ]

  

[Emulation ]

[SOLID Standard ]

  

[HP PCL 5 ]

[Save as Setup? ]

Notes

Turn the printer OFF LINE with this key.

Press the NEXT or PREVIOUS key until [Configuration ] is displayed.

Press the NEXT or PREVIOUS key until [Emulation ] is displayed.

Press the NEXT or PREVIOUS key until the desired emulation (e.g. HP PCL 5) is displayed.

The emulation HP PCL 5 is selected.

In addition this new value can be saved as setup value (using the SELECT key), before the printer is turned ON LINE again.

92 Panel Functions

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Available emulations:

Standard:

MICROPLEX IDOL, HP LaserJet (PCL 5), IBM Proprinter, Diablo 630, Epson FX, TIFF (CCITT group 4),

µPostscript

Optional:

Kyocera Prescribe, Printronix IGP/PGL,

QMS (Magnum) Code V, ZPL II (Zebra Programming Language), Datamax (FGL), Eltron EPL2, Express

(More emulations on request)

Notice:

The brand names mentioned are registered trademarks of the enterprises named above.

Panel Functions 93

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

5.17. Display Language Selection

This function enables the user to determine the language for the display messages, the status sheet and the font list.

Panel display

[SOLID 50 A3 - 3 ]

[Menu Level 1 ]

  

[Configuration ]

[Interface ]

  

[Language ]

[German ]

  

[English ]

[Save as Setup? ]

Notes

Turn the printer OFF LINE with this key.

Press the NEXT or PREVIOUS key until [Configuration] is displayed.

Press the NEXT or PREVIOUS key until [Language ] is displayed.

Press the NEXT or PREVIOUS key until the desired language (e.g. English) is displayed.

The display language English is selected.

In addition this new value can be saved as setup value (using the SELECT key), before the printer is turned ON LINE again.

94 Panel Functions

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

5.18. Transparent Code Adjustment

This function configures the transparent code. Using the transparent code enables you to initiate the commands of the page description language IDOL by printable characters. The transparent code pre-setting is 2625. These are the ASCII character

codes (hexadecimal) for the characters   (ref. IDOL Programming Manual).

Panel display

[SOLID 50 A3 - 3 ]

[Menu Level 1 ]

   [Configuration ]

[Interface]

   [Transparent Code ]

[Digit4 2625]

  

[Digit1 2626]

[Save as Setup? ]

Notes

Turn the printer OFF LINE with this key.

Press the NEXT or PREVIOUS key until [Configuration ] is displayed.

Press the NEXT or PREVIOUS key until [Transparent Code ] is displayed.

The hexadecimal number for   is preset. Activating the NEXT or PREVIOUS key changes the value of the current position (Digit4 = left position, in this example: 2). Pressing the SELECT key moves you to the next position (the RETURN key moves you back).

2626 is selected as transparent code. From now on use the characters   before

programming the IDOL commands.

In addition this new value can be saved as setup value (using the SELECT key), before the printer is turned ON LINE again.

Panel Functions 95

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

5.19. Selection of Memory Distribution (Input Buffer)

This function enables the user to choose the distribution of the available RAM memory between input buffer and macro/download memory.

Panel display

[SOLID 50 A3 - 3 ]

[Menu Level 1 ]

  

[Configuration ]

[Interface ]

  

[Input Buffer ]

[32 kB ]

  

[100 kB ]

[Save as Setup? ]

Notes

Turn the printer OFF LINE with this key.

Press the NEXT or PREVIOUS key until [Configuration ] is displayed.

Press the NEXT or PREVIOUS key until [Input Buffer ] is displayed.

Press the NEXT or PREVIOUS key until the desired memory distribution is displayed. The input buffer size is specified in kilobyte (kB) or in percent of the installed memory.

100 kB is selected as input buffer.

In addition this new value can be saved as setup value (using the SELECT key), before the printer is turned ON LINE again.

96 Panel Functions

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

5.20. Setting to Factory Default

This function back-outs all configurations to factory defaults.

Panel display

[SOLID 50 A3 - 3 ]

[Menu Level 1 ]

  

[Configuration ]

[Interface ]

  

[Factory Default ]

[Save as Setup? ]

Notes

Turn the printer OFF LINE with this key.

Press the NEXT or PREVIOUS key until [Configuration ] is displayed.

Press the NEXT or PREVIOUS key until [Factory Default ] is displayed.

Only if you press the SELECT key a second time the configuration will be back-outed to factory defaults.

The printer is turned ON LINE again.

Panel Functions 97

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

5.21. Font Selection

This function selects the active font. Select a font number out of the list of available fonts.

Panel display

[SOLID 50 A3 - 3 ]

[Menu Level 1 ]

  

[Page Menu ]

[Font Number ]

[Font 0600 ]

  

[Font 5507 ]

[Save as Setup? ]

Notes

Turn the printer OFF LINE with this key.

Press the NEXT or PREVIOUS key until [Page Menu ] is displayed.

Press the NEXT or PREVIOUS key until the desired font number (5507 Langeoog e.g.) is displayed.

The font number 5507 Langeoog is selected.

In addition this new value can be saved as setup value (using the SELECT key), before the printer is turned ON LINE again.

98 Panel Functions

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

Explanations:

The SOLID 50 A3 - 3 standard equipment contains the following fonts:

Font no. Font width Font height Font name

0600 10 12 Kurilen 0602 10 12 Kurilen Italic 0610 12 10.1 Kurilen 1710 12 10.1 Kurilen Italic 4508 P 8.1 Helgoland 4510 P 10 Helgoland 4714 P 14.4 Helgoland Bold 5507 20 7 Langeoog 5508 16.6 7.9 Langeoog 5509 15 9.1 Langeoog 6610 10 10.1 Juist Monosp. 9210 P 10.1 Tasmanien 9310 P 10.1 Tasmanien Italic 2000 P SC Tasmanien 9900 P SC Neuwerk

Resumption of this standard font list see next page.

Font width: Character distance in CPI (Characters Per Inch). P = proportional, (meaning that each character has an individual width).

Font height:

Font height from the lowest descender to the upper edge of the highest

character, measured in graphical points (1/72 inch).

SC = scalable.

Panel Functions 99

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

PCL 5 compatible

Notes:

Font no. Font width Font height Font name

0050 SC Plakatschrift 0590 SC OCR /B 0591 SC OCR /A 6600 SC Juist Monospaced 0699 SC Kurilen 1700 SC Kurilen Italic 1800 SC Kurilen Bold 1900 SC Kurilen Bold Italic 5500 SC Langeoog 5600 SC Langeoog Bold 5700 SC Langeoog Italic 5800 SC Langeoog Bold Italic 2100 P SC Texel Bold 2200 P SC Texel Italic 2300 P SC Texel Bold Italic 9800 P SC Neuwerk Italic 9500 P SC Neuwerk Bold Italic 9600 P SC Neuwerk Bold 0060 SC Plakatschrift 9501 P SC Neuwerk-II Condensed Italic 9601 P SC Neuwerk-II Condensed Bold Ital. 9801 P SC Neuwerk-II Condensed BoId 9901 P SC Neuwerk-II Condensed 0530 P SC PiktoWin 5100 P SC Amrum 5200 P SC Amrum Bold 5300 P SC Amrum Italic 7500 P SC Antigua 7700 P SC Antigua Bold 7800 P SC Antigua Italic 7900 P SC Antigua Bold Italic 9199 P SC Tasmanien-II Bold Italic 9299 P SC Tasmanien-II 9399 P SC Tasmanien-II Italic 9499 P SC Tasmanien-II Bold

Additional fonts can be selected from the font catalogue depending upon the memory capacity.

You can use the panel function Printing the Font List (see section

5.2) to generate a list of all fonts installed to the printer.

100 Panel Functions

_______________________________________________________________________________________________

MICROPLEX Operator’s Manual SOLID 50 A3 - 3 Edition 2.1

5.22. Text Orientation Selection

This function selects the active text orientation.

Panel display

[SOLID 50 A3 - 3 ]

[Menu Level 1 ]

   [Page Menu ]

[Font Number ]

  

[Orientation ]

[Orientation 0 ]

   [Orientation 1 ]

[Save as Setup? ]

Notes

Turn the printer OFF LINE with this key.

Press the NEXT or PREVIOUS key until [Page Menu ] is displayed.

Press the NEXT or PREVIOUS key until [Orientation ] is displayed.

Press the NEXT or PREVIOUS key until the desired orientation is displayed.

The orientation 1 = landscape is selected.

In addition this new value can be saved as setup value (using the SELECT key), before the printer is turned ON LINE again.

Text orientation assignment:

Orientation 0 = Portrait (upright format) Orientation 1 = Landscape (horizontal format) Orientation 2 = Portrait upside down Orientation 3 = Landscape upside down

Microplex SOLID 50 A3 - 3 Operator's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual