Micron PC F1700 User Manual

F1700 LCD Monitor

User’s Guide

2

TABLE OF CONTENTS

Monitor User’s Guide .................................................................3

Packing List ................................................................................3

Safety Information......................................................................3

LCD Monitor Features................................................................5

Monitor Features ...................................................................................5

Setup Instructions......................................................................6

Monitor Base .........................................................................................6

Power Cord and Power Adapter............................................................6

Video Cable...........................................................................................8

Adjusting the Viewing Angle .....................................................8

Operating Instructions...............................................................9

General Instructions ..............................................................................9

Cleaning the Monitor..............................................................................9

Front Panel Controls..............................................................................9

Accessing the Adjustment Controls.....................................................11

Adjusting the Picture............................................................................12

Monitor Drivers.........................................................................13

Warranty Information ...............................................................13

Features ....................................................................................14

Energy Star Standards ........................................................................14

Plug & Play DDC1/2B Feature.............................................................14

Appendix A — Troubleshooting ..............................................15

Appendix B — VESA Mounting................................................17

Attaching an Optional Wall-Mounting Arm ..........................................17

Appendix C — On-Screen Messages ......................................18

Appendix D — Factory Preset Timing.....................................19

Appendix E — Connector Pin Assignment.............................20

Appendix F — Acceptable LCD Defects..................................21

Appendix G — Monitor Specifications....................................21

Appendix H — FCC Notice.......................................................23

3

MONITOR USER’S GUIDE

This user’s guide provides important information about operating your
monitor. Before using the monitor, please read the guide thoroughly, and
then save it for future reference.

PACKING LIST

Before setting up and using your monitor, examine the items in the monitor
package. If anything is missing or damaged, please contact MicronPC
immediately. Look for the following items:

• 17” LCD Monitor

• F1700 LCD Monitor User’s Guide

• 100/120 VAC rated Power Cord

• External Power Adapter Brick (12 VDC)

• Monitor Base

Note: Save the original shipping carton and packing materials in case you
ever need to transport or ship your monitor. If you transport the monitor
over long distances, completely repackage the monitor in its original
packing material.

SAFETY INFORMATION

• Do not use the monitor near standing bodies of water or in humid

envirionments.

• Set the monitor on a flat, stable surface. Do not place it on an unstable

cart, stand, or table. If the monitor falls, it might injure a person and/or
cause serious damage to the monitor.

• When placing the monitor on a cart or stand, use only a cart or stand

recommended by the manufacturer or sold with the monitor. If you
mount the monitor on a wall or shelf, use a mounting kit approved by the
manufacturer and follow the kit instructions.

• Slots and openings in the back and bottom of the monitor are provided

for ventilation. To ensure reliable operation of the monitor, and to protect
it from overheating, these openings must not be blocked or covered. Do
not place the monitor on a bed, sofa, rug, or similar surface. This
monitor must never be placed near or over a radiator or heat register.
This monitor must not be placed in a built-in enclosure of any kind
unless proper ventilation is provided.

4

• The monitor must only be connected to the AC power source as

indicated on the label. If you are unsure of the type of AC power
available, ask your local power company. Only connect this monitor to a
power outlet that matches the power requirements of this monitor.

• The monitor is equipped with a three-prong, grounded plug (a plug with a

third pin for grounding). For safety purposes, this plug will only fit into a
grounded power outlet. If your outlet does not accommodate the three­wire plug, have an electrician install the correct type of outlet, or use an
adapter to ground the appliance safely.

• During a lightning storm, unplug the monitor. Also unplug the monitor

when it will not be used for a long time. This will protect the monitor from
damage due to power surges.

• Do not overload power strips and extension cords. Overloading power

strips and extension cords can result in a fire or electric shock.

• Never push objects of any kind into the monitor through openings. The

objects could touch dangerous voltage points or short out parts, possibly
resulting in an electric shock or a fire hazard.

• Never spill liquid of any kind on the monitor. If this occurs, disconnect

from the power source immediately.

• Do not attempt to service the monitor yourself. Opening or removing the

monitor’s cover can expose you to dangerous voltages and other
hazards. Please refer all servicing to qualified service personnel.

• To ensure satisfactory operation, only use the monitor with UL listed

computers that have the appropriate configured receptacles marked
between 100–240 VAC, Min. 3.5A.

• Do not allow anything to rest on the power cord. Do not place the

monitor where people might walk on the cord.

• Do not place the monitor in direct sunlight, or where it is near excessive

dust or mechanical vibration or shock.

• This monitor is for use only with the included power adaptor (output

12Vdc) that has a UL, CSA listed license.

Warning: To prevent a fire or shock hazard, do not expose the
monitor to rain or moisture. Dangerously high voltages are present
inside the monitor. Do not open the monitor cabinet. Refer servicing
to qualified personnel only.

Warning: Keep all packing materials away from children.

5

LCD MONITOR FEATURES

Monitor Features

• 17-inch (43.2 cm) TFT Color LCD Monitor

• 75 mm x 75 mm VESA Mounting Pad

• EPA ENERGY STAR

®

• Ergonomic Design (complies with MPRII)

• Space Saving, Compact Case Design

The following occurrences are normal with an LCD monitor and do not
indicate a problem.

• Due to the nature of the internal fluorescent backlights, the screen may

flicker during initial use. If this occurs, turn off the monitor and then turn
it on again, making sure the flicker disappears.

• You may find slightly uneven brightness on the screen depending on the

desktop pattern you use.

• The LCD screen has an effective pixel count of 99.99% or more. It may

include blemishes of 0.01% or less, such as a missing pixel or a pixel lit
all of the time. Refer to “Appendix F — Acceptable LCD Defects” for
additional details.

• Due to the nature of the LCD screen, an after-image or ghost of the

previous image may remain after switching the image when the same
image is displayed for a long time. In this case, you can recover the
screen slowly by changing the image or turning off the monitor for a few
hours.

• The life of the internal fluorescent backlights used in the LCD monitor is

approximately 10,000 hours. Contact MicronPC technical support or an
authorized dealer for a replacement when the screen is dark, flickering,
or not lighting up. Never attempt to replace the light yourself. Refer
servicing to qualified personnel only.

6

SETUP INSTRUCTIONS

The following sections provide information about attaching the swivel base to
your monitor and using the power cord and video cable.

Monitor Base

To install the monitor base, put the monitor in the base until it snaps into
place. To remove the monitor base, gently turn monitor upside down and
press the four retention clips together to release the base. Pull the base
straight away from the monitor. See Figure 1 below.

Install Remove

Figure 1: Installing and Removing the Monitor Base

Power Cord and Power Adapter

Before connecting your monitor’s power cord and adapter, read the
guidelines below:

• Only use the Power Adapter included with your monitor. You should find

the following markings on the Power Adapter included with your monitor:

Manufacturer: Polaris Electronics (Dong guan) Co; Ltd. (CHI SAM)
Model: CH -1205
Output: 12 VDC 5 A

• This monitor has a universal power supply, so it can operate in either a

100/120 VAC or 220/240 VAC voltage area (no user adjustment is
required).

• Make sure the power cord meets the specifications and requirements for

your area. The power cord included with your monitor is rated for
100/120 VAC.

7

To connect the power cord to your monitor and a power source, follow the
steps below:

Caution: If the AC outlet is not grounded (with three holes), install the
proper grounding adapter (not supplied).

1 Plug the power cord into the supplied external power adapter brick. Plug

the small end of the power adapter cord (DC Plug) into your monitor’s
power input socket (CD Jack). See Figure 2.

Video Cable

DC Plug

DC Jack

AC Power
Cord

External Power
Adapter Brick

DC IN

Figure 2: Connecting Cables

2 Plug the other end of the power cord into a three-pin AC power outlet or

a UL-approved power strip.

Note: A certified power supply cord must be used with this equipment. The
relevant national installation and/or equipment regulations need to be
considered. Use a cord that meets the following criteria:

• Monitor side must have IEC320-type female, straight plug

• Main side must have IEC320-type male, straight plug

• Wire type must be UL/CSA certified, 18 AWG X 3C

8

Video Cable

The monitor comes with the video cable connection built into the monitor. To
connect the video cable to your computer’s video port, complete the
following steps:

Caution: Do not bend the signal cable excessively, or you might
break the wires inside the cable.

1 Plug the video cable's 15-pin connector (see Figure 2 on page 7) into the

computer's video port, taking care not to bend any pins on the
connector.

2 Tighten the two screws on the video connector with your fingers to

secure the connection.

Note: Over-tightening this connection can damage the monitor cable or
your computer’s video card.

ADJUSTING THE VIEWING ANGLE

• For optimal viewing, look at the full face of the monitor, and then adjust

the monitor’s angle to your own preference.

• Hold the base so the monitor does not fall when you change the

monitor’s angle.

•

You are able to adjust the monitor’s angle from -5° to 25°.

-5

25

Figure 3: Adjusting the Monitor’s Angle

Caution: Do not touch the LCD screen when you change the angle, or
the screen may become damaged or broken.

9

Warning: Be careful not to pinch your fingers when adjusting the
monitor’s angle.

OPERATING INSTRUCTIONS

The following sections provide information about operating and adjusting
your monitor.

General Instructions

To turn on the monitor, do the following:
1 Check that the power supply is connected to the monitor and a power

outlet or socket.

2 Check that the video cable is connected to your computer’s video port.
3 Locate the power button (see Figure 4 and Table 1 on page 10).
4 Press the power button. The power indicator will light up. The monitor

features a unique quick-switch system, so a picture should appear within
seconds after the monitor is turned on.

Cleaning the Monitor

To keep the monitor looking new, periodically clean the monitor’s case with a
soft cloth. As a safety precaution, always unplug the monitor before cleaning
it. Stubborn stains on the monitor’s case can be removed using a damp,
dust-free cloth and a mild detergent solution.

Caution: Never use strong solvents, such as thinner, benzene, or
abrasive cleaners, because these will damage the monitor.

To clean the LCD screen, use a damp cloth; however, make sure the
monitor has been turned off first. Never apply water directly to the LCD
screen. Always apply the water to the cloth first, and then wipe down the
screen. You can also purchase and use monitor wipes to clean the LCD
screen.

Front Panel Controls

The power button is located on the front panel of the monitor. The buttons to
the left of the power button are for adjusting the monitor’s picture. See
Figure 4 and Table 1 on page 10 for the layout and names of the control
buttons.

10

Figure 4: Control Buttons

Table 1: Control Buttons Descriptions

Feature Description

1 Auto Config/Exit

The Auto Config button is used to automatically
set the H-Pos, V-Pos, Clock, and Focus. Press
and hold this button for 2 seconds to begin the
auto config cycle. This also acts as the Exit
button. Press it to close the OSD menu. This will
also back out of a menu selection.

2

Brightness /

Press this button to adjust your monitor’s
brightness. If the OSD is open, this button will
move through the selections in a counter­clockwise direction.

3 Contrast /

Press this button to adjust your monitor’s
contrast. If the OSD is open, this button will move
through the selections in a clockwise direction.

4 Menu/Enter Press this button to open the (OSD) menu or to

select an adjustment icon within the OSD.

5 Power Indicator Power Indicator:

Green = power on mode (normal operation)
Orange = low power mode (low power
consumption; no picture)

6 Power Button Press this button to turn the monitor on and off.

11

Accessing the Adjustment Controls

The following list explains how to access and use the adjustment controls
appearing in the On Screen Display (OSD) Main Menu:

1 Press the Menu button to make the OSD window appear. The menu will

look like Figure 5.

2 Press the or buttons to select the desired function.
3 Press the Menu button to select the function that you want to adjust.
4 Press the or buttons to change the settings of the current function.

• When the OSD window is active, it shows the input signal timing.

The H stands for the horizontal frequency and V for the vertical
frequency.

• To exit and save, select the exit functions, or leave the monitor

alone for 10 seconds. If you want to adjust any other function, repeat
steps 2-4.

78

65

R

EXIT

B

G

R

H:60KHz

V:75KHz

Contrast

70

Figure 5: On Screen Display (OSD) Menu

Note: If you do not make any OSD menu adjustments or selections for
more than 10 seconds, the current setup will be saved, and the OSD will
disappear automatically.

12

Adjusting the Picture

The table below describes the functional control icons that appear on the
OSD menu.

Table 2: Functional Control Icons

Function Icon Description

Contrast

Use this function to adjust the picture’s contrast.

Brightness

Use this function to adjust the picture’s brightness.

Focus

Use this function to adjust the picture’s focus.
The Focus adjusts the phase of the pixel clock

signal. With a wrong phase adjustment the picture
has horizontal disturbances or lines in a bright
picture.

Clock

Use this function to adjust the picture’s clock.
The Clock (pixel frequency) controls the number

of pixels scanned by one horizontal sweep. If the
frequency is not correct, the screen shows vertical
stripes and the picture will not be the correct
width.

H-Position

Use this function to adjust the picture’s horizontal
position.

V-Position

Use this function to adjust the picture’s vertical
position.

Auto Center

Use this function to automatically center the
picture in the display area. This will not adjust the
Clock and Focus controls.

Language

Use this function to select which language the
monitor will use to display the instructions.

DOS Mode
Select

Use this function to switch the default DOS mode
between 640 x 400 @ 70 Hz and 720 x 400 @ 70
Hz.

(7800K) Color

78

The color temperature of 7800°K can be selected
here.

13

Table 2: Functional Control Icons (Continued)

Function Icon Description

(6500K) Color

65

The color temperature of 6500°K can be selected
here.

Reset

Use this function to clear each old status of auto­configuration and to redo auto-configuration.

Exit

Use this feature to save your selections and
adjustments and to exit the OSD menu.

Blue

Use this function to adjust the picture’s blue
intensity.

Green

Use this function to adjust the picture’s green
intensity.

Red

Use this function to adjust the picture’s red
intensity.

MONITOR DRIVERS

During normal operation, your system will automatically detect your monitor,
and Plug and Play drivers will automatically be installed.

If your application requires a specific monitor driver and color matching
profile, these can be downloaded from the MicronPC Technical Support Site
at http://www.micronpc.com/support/index.html.

If you do not have Internet access, you may also call MicronPC Technical
Support at [phone] to request the files be sent to you.

WARRANTY INFORMATION

In the unlikely event that you have a failure with your MicronPC monitor, you
can contact MicronPC Technical Support at
http://www.micronpc.com/support/index.html.

If you do not have Internet access, you may also call MicronPC Technical
Support at [phone].

Technical Support will provide you with instructions for returning the failed
monitor.

14

FEATURES

Energy Star Standards

This monitor may appear to be non-functional if there is no video input
signal. For this monitor to operate properly, there must be a video input
signal.

This monitor meets power management standards as set by the Video
Electronics Standards Association (VESA) and/or the United States
Environmental Protection Agency (EPA) and the Swedish Confederation
Employees ( NUTEK ). This feature is designed to conserve electrical energy
by reducing power consumption when there is no video input signal present.
When there is no video input signal, this monitor, following a time-out period,
will automatically switch to a low power consumption mode. This reduces the
monitor's internal power supply consumption. After the video input signal is
restored, full power is restored, and the display is automatically redrawn. The
appearance is similar to a "Screen Saver" feature, except the display is
completely off. The display is restored by pressing a key on the keyboard or
clicking the mouse.

Plug & Play DDC1/2B Feature

This monitor is equipped with VESA DDC1/2B capabilities according to the
VESA DDC STANDARD. These capabilities allow the monitor to inform the
host system of its identity and, depending on the level of DDC used,
communicate additional information about its display capabilities. The
communication channel is defined in two levels: DDC1 and DDC2B.

The DDC1 is a uni-directional data channel from the display to the host that
continuously transmits EDID information. The DDC2B is a bi-directional data
channel based on the I²C protocol. The host can request EDID information
over the DDC2B channel.

See “Appendix E — Connector Pin Assignment” on page 20 for connector
pin assignments.

15

APPENDIX A — TROUBLESHOOTING

If the following information does not successfully solve your issue, please
visit the MicronPC Technical Support Site at
http://www.micronpc.com/support/index.html.

If you do not have Internet access, you may also call MicronPC Technical
Support at [phone].

Table 3: Troubleshooting Monitor Issues

Issue Solution

The power indicator
LED is not lit.

• Press the monitor power button once to see

if the LED comes on.

• Verify that the power cord is plugged in firmly

and correctly.

The monitor is not
detected by the
system when it is
connected.

• Verify the PC system is Plug & Play

compatible.

• Verify the Video Card is Plug & Play

compatible.

• Check the DB-15 plug on the Video Cable for

bent pins.

The picture is fuzzy.

• Adjust the contrast and brightness controls.

• Initiate the automatic calibration function by

pressing the ‘Auto’ button.

The picture bounces
or a wave pattern is
present in the picture.

• Initiate the automatic calibration function by

pressing the ‘Auto’ button.

• Manually adjust the Clock and Focus

controls for better picture.

The monitor’s picture
is missing one of the
primary colors (red,
green, or blue).

• Inspect the monitor’s video cable and make

sure that none of the pins are bent.

The picture has color
defects (white does
not look white).

• Adjust the RGB color or select a color

temperature.

16

Table 3: Troubleshooting Monitor Issues (Continued)

Issue Solution

The power LED is on
(orange), but there is
no video or picture.

• Maker sure the computer’s video card is

completely seated in the slot.

• Make sure the monitor’s video cable is

properly connected to the computer.

• Inspect the monitor’s video cable and make

sure that none of the pins are bent.

• Make sure the computer is operational by

pressing the [Caps Lock] key on the
keyboard while observing the Caps Lock
LED. The LED should either turn on or off
after you press the [Caps Lock] key.

• Your computer may be in a low power state.

Move the system’s mouse and press several
keys on the keyboard to wake the system.

The screen image is
not centered or sized
properly.

• Adjust pixel frequency (Clock) and Focus, or

press the Auto Config button.

• Select the Auto Center function in the OSD

to center the display.

The picture has poor
brightness or
contrast.

• The lifetime of the back-light is limited. After

10,000 hours of use, the luminance of the
light may be reduced to half of its original
value. Please send the monitor to an
authorized service agent for service.

There are horizontal
or vertical
disturbances on the
screen.

• Use a pattern with a repetitive dot pattern to

manually adjust the Clock and Focus, or
press the Auto Config button.

17

APPENDIX B — VESA MOUNTING

Attaching an Optional Wall-Mounting Arm

This monitor can be attached to a wall-mounting arm, which you purchase
separately. This monitor has a 75 mm x 75 mm VESA compliant mounting
pad. Use a wall-mounting arm with this configuration only.

Caution: Be careful when installing the wall-mounting arm. Make sure
you properly support the monitor, so the LCD panel is not damaged.

Preparing to Install a Wall-Mounting Arm

To prepare to install a wall-mounting arm, complete the following steps:
1 If the monitor is currently in use, turn it off and disconnect the power

adapter.

2 Pull the screw covers off the back of the monitor. See Figure 6.)
3 Support the base and remove the screws.
4 Remove the base. (See Figure 6.)

Figure 6: Preparing to Install an Optional Wall-Mounting Arm

5 Follow the manufacturer's instructions to assemble the wall mounting

arm.

18

Installing a Wall-Mounting Arm

To install the wall-mounting arm, complete the following steps:
1 Place the wall mounting arm onto the back of the monitor. Line up the

holes of the arm with the holes in the back of the monitor.
(See Figure 7.)

Figure 7: Installing a Wall-Mounting Arm

2 Insert the four screws into the holes and tighten (see Figure 7). Be

careful to not over tighten the screws.

3 Insert the power cable into the slot on the back of the monitor.

APPENDIX C — ON-SCREEN MESSAGES

Table 4: On-Screen Messages

Message Action

“Cable Not
Connected”

• Check that the signal cable is properly

connected. If the connector is loose, tighten
the connector screws.

• Check the DB-15 plug on the video cable for

bent pins or other damage.

“Input Not Supported”

• Your system may be set outside the display

mode range of the monitor. Verify you are
using a compatable display mode. See Table
5: Factory Preset Timing.

19

APPENDIX D — FACTORY PRESET TIMING

Table 5: Factory Preset Timing

Standard Resolution Horizontal

Frequency

Vertical
Frequency

640 x 350 31.469 kHz 70 Hz
640 x 400 31.469 kHz 70 Hz

DOS

720 x 400 31.469 kHz 70 Hz
640 x 480 31.470 kHz 60 Hz
640 x 480 37.861 kHz 72 Hz

VGA

640 x 480 37.500 kHz 75 Hz
800 x 600 37.879 kHz 60 Hz
800 x 600 48.077 kHz 72 Hz

SVGA

800 x 600 46.875 kHz 75 Hz
1024 x 768 48.363 kHz 60 Hz
1024 x 768 56.476 kHz 70 Hz

XGA

1024 x 768 60.023 kHz 75 Hz
1280 x 1024 63.981 kHz 60 Hz

SXGA

1280 x 1024 79.976 kHz 75 Hz

20

APPENDIX E — CONNECTOR PIN
ASSIGNMENT

1 5
6

10

11 15

Figure 8: 15-pin Color Display Signal Cable

Table 6: Video Cable Pin Assignments

Pin # Description Pin # Description

1 Red 9 +5V
2 Green 10 Detect Cable
3 Blue 11 NC
4 Ground 12 DDC-Serial Data
5 Ground 13 H-sync
6 R-Ground 14 V-sync
7 G-Ground 15 DDC-Serial Clock
8 B-Ground

21

APPENDIX F — ACCEPTABLE LCD DEFECTS

Table 7: Acceptable LCD Panel Defects

Bright Dot Failures

(Always On)
Bright dots are tested

with full screen black
pattern (R,G,B=0,0,0)

• Maximum five red, green or blue bright

dots (sub-pixels)

• Maximum three green dots

• Maximum one joined bright dots

• Minimum distance between two bright

dots: 10 mm

Black Dot Failures

(Always Off)
Black dots are tested with

full screen white pattern
(R,G,B=255,255,255)

• Maximum five black dots

• Maximum two joined (two adjacent)

black dots

• Minimum distance between two black

dots: 10mm

• No defects allowed with three adjacent

black dots

Total Dot Failures

• Maximum of eight dots (including bright

and dark dot defects)

APPENDIX G — MONITOR SPECIFICATIONS

Table 9: Monitor Specifications

LCD Panel

• Type: TFT Active Matrix Color LCD

• Size: 17.0 in (43.2 cm)

• Viewable Size: 17.0 in (43.2 cm)

• Pixel pitch: 0.264 mm(H) x 0.264 mm(V)

• Viewing angles: 140°(H) 110°(V) (Typical)

• Response time: 30 ms (Typical)

• Native Panel Resolution: 1280 x 1024

• Contrast Ratio: 300:1 (Typical)

• Brightness: 250 nits (Typical)

22

Table 9: Monitor Specifications (Continued)

Scan Range

• H-Frequency: 30 kHz to 80 kHz

• V-Frequency: 55 Hz to 75 Hz

Dot Clock

• 135 MHz

Recommended
Viewing Resolutions

• Minimum: 640 x 480 @ 60 Hz

• Nominal: 1280 x 1024 @ 60 Hz

• Maximum: 1280 x 1024 @ 75 Hz

Maximum Resolution

• 1280 x 1024 @ 75 Hz

Display Colors

• 16.7 million Colors

Plug & Play

• VESA DDC1/2B

TM

EPA ENERGY STAR®

• On Mode: <45 W

• Off Mode: <3 W

Input Connector

• 15-pin D-Sub

Input Video Signal

• Analog: 0.7 Vp-p (standard)

• 75 OHM

• Positive

Power Source

• AC Source: 100 to 240 VAC 50/60 Hz

• DC Adapter: 12 VDC 5 A

Environmental
Considerations

• Operating Temp: 41°F to 95°F

(5°C to 35°C)

• Storage Temp: -4°F to 140°F

(-20°C to 60°C)

• Operating Humidity: 10% to 85%

Weight

• Shipping: 15.4 lb (7.0 kg)

• Display Only: 12.6 lb (5.7 kg)

Dimensions

• 407(W) x 436(H) x 173(D) mm

Regulatory
Compliance

• UL, CSA, FCC, GS/TÜV, CE

23

APPENDIX H — FCC NOTICE

FCC Class B Radio Frequency Interference Statement
WARNING: (FOR FCC CERTIFIED MODELS) This equipment has been

tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio
frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

1 Reorient or relocate the receiving antenna.
2 Increase the separation between the equipment and receiver.
3 Plug the equipment into an outlet on a different circuit than the receiver

is connected.

4 Consult the dealer or an experienced radio/TV technician for help.

Notice:

Any changes or modifications to the monitor not expressly approved by the
party responsible for compliance could void the user's authority to operate
the equipment.

Shielded interface cables and AC power cord, if any, must be used to
comply with the emission limits.

The manufacturer is not responsible for any radio or TV interference caused
by unauthorized modification to this equipment. It is the responsibility of the
user to correct such interference.

This product meets the ENERGY STAR guidelines for energy efficiency.