How to change SP912 from Bridge to Access Point mode
1. Since this device has changed to Bridge mode, the default
IP address is 192.168.1.1. 1.
2. Enter the default IP address (192.168.1.1) into the address
bar of web-browser.1.
Status
Click on the System link on the navigation bar. The information
page is the first page that is displayed once you have logged in.
You can know what mode you are using and realize system
information.
3. By default, a user name and password is "admin".
4. Once you have logged in, click on the Admin link on the
4.
navigation bar.
5. Look for Commands function and then click on the Switch
button to switch the operation mode to Access Point.
4.
6. Wait for about 1 minute and the device will automatically
restart into Access Point mode.
4.
5
Access Point Mode
Bridge Mode
6
Specifications
Model
Standard
LAN Port
Radio Modulation
Frequency Band
Data Rate
Output Power (Max)
Security
Operation Channel
Operation Mode
Antenna Type
Management
Power
Weight (g)
Dimension (mm)
Operating
Temperature (°C)
Operating Humidity
Emission
SP912
IEEE 802.11b compliant
One 10Base-T RJ-45 LAN Port
DSSS
2.4 GHz
11, 5.5, 2 and 1 Mbps, Auto Fall-Back
23 dBm
MAC address filtering (AP Mode),
WEP Encryption (64/128 bit),
Hide SSID in beacons, and
Wireless Isolation in AP Mode
11/N. America( FCC), 13/Europe (ETSI)
Point-to-Point, Point-to-Multipoint,
Infrastructure
TNC Female-Reverse
Web-Based
DC 12V, 1A
350
125 x 105 x 31
0°C - 55°C
5% - 95%, Typical
FCC Part 15/UL, ETSI 300/328/CE
Quick Installation Guide
Wireless LAN Bridge
Model No.: SP912
P/N: 2300-0470
Web: www.micronet.com.tw
Introduction
Installation
Thank you for purchasing Micronet Wireless LAN Bridge SP912.
It operates seamlessly in the 2.4 GHz frequency spectrum
supporting the 802.11b (2.4GHz, 11Mbps) wireless standards.
It's the best way to add wireless stable to your existing wired
network. SP912 has high transmitted output power and high
receivable sensitivity. High output power and high sensitivity
can extend range and coverage to reduce the roaming between
APs to get more stability wireless connection. It also can reduce
the expense of equipment in the same environment.
To protect your wireless connectivity, SP912 can encrypt all
wireless transmissions through 64/128-bit WEP data encryption.
The MAC address filter lets you select exactly which stations
should have access to your network. This user guide is aimed
at helping you easily set up this device. Before your installation,
please read the following procedures carefully.
Package Contents
• One SP912 Unit
• One Power Adapter (12V, 1A)
• One Omni directional Antenna
• One CD-ROM with User's Manual
• One Quick Installation Guide
1. Wired LAN connection: Connect an Ethernet cable
1.
(i.e. UTP/STP Straight RJ45) from your computer's Ethernet
1.
(RJ45) port to LAN port of this Client Bridge.
2. Wireless LAN connection: Locate this Client Bridge at open
1.
environment to gain best Signal Strength.
3. Power on: Plug the power cord into the outlet and this
1.
Client Bridge.
IP Address Configuration
This device can be configured in Bridge mode or Access Point
mode. The default IP address of the device is 192.168.1.1. In
order to log into SP912, you must first configure the TCP/IP
settings of your PC/Notebook.
Step1. In the control panel,
Step1.
double click Network
Step1.
Connections and
Step1.
then double click on
Step1.
the connection of
Step1.
your Network
Step1.
Interface Card (NIC).
Step1.
You will then see the
Step1.
following screen.
1 2
Step2. Select Internet
Step1.
Protocol
Step1.
(TCP/IP), and
Step1.
then click on the
Step1.
Properties
Step1.
button.
Step1.
This will allow
Step1.
you to configure
Step1.
the TCP/IP
Step1.
settings of your
Step1.
PC/Notebook.
Step3. Select Use the following IP Address radio button and
then enter the IP address and subnet mask. Ensure that
Step3.
the IP address and subnet mask are on the same
Step3.
subnet as the device.
Step3.
For Example
: Device IP address: 192.168.1.1
Configure SP912 in AP / Bridge Mode
How to change SP912 from Access Point to Bridge
1. SP912's default setting is Access Point mode, and this
1.
device's management IP address is 192.168.1.1.
2. Enter the default IP address (192.168.1.1) of the bridge into
1.
the address bar of the web-browser.
3. By default, a user name and password is "admin".
4. Once you have logged in, click on the Admin link.
5. Look for Commands function and then click on the
1.
Switch button to switch the operating mode to Bridge mode.
6. Wait for about 1 minute and the device will automatically
1.
restart into Bridge mode.
PC IP address
PC Subnet Mask
Step4. Click on the OK button to close this window, and then
you can once again to close LAN properties windows.
Step4.
: 192.168.1.10
: 255.255.255.0
3
4
Loading...