User’s Manual
SP659A
10/100/1000 Mbps Gigabit Smart Switch
Website: http://www.micronet.com.tw
1
2
FCC Warning
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limitations are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate rad io
frequency energy and, if no installed and used in accordance with the
instructions, may cause harmful interference to radio commun icatio ns. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into a different outlet from that the receiver is
connected.
Consult your local distributors or an experienced radio/TV technician for
help.
Shielded interface cables must be used in order to comply with emission
limits.
Changes or modifications to the equipment, that are not approved by the party
responsible for compliance could affect the user’s authority to operate the
equipment.
Copyright © 2001 All Rights Reserved.
Company has an on-going policy of upgrading its products and it may be
possible that information in this document is not up-to-date. Please check with
your local distributors for the latest information. No part of this document can
be copied or reproduced in any form without wr itten consent from the
company.
Trademarks:
All trade names and trademarks are the properties of their respective
companies.
3
Table of Contents
1. Unpacking Information
2. Introduction To SP659A 10/100/1000M Smart Switch
2.1 General Description
2.2 Key Features
2.3 The Front Panel
2.3.1 System LEDs
2.3.1.1 Power LED
2.3.2 Port LEDs
2.3.2.1 Speed/Link/Act LED
2.3.2.2 FDX/COL LED
2.3.3 Gigabit Port LEDs
2.4 The Rear Panel
2.4.1 Power Connecting
2.4.2 Console Port
3. Installing And Using SP659A 10/100/1000M Smart Switch
3.1 Installing The SP659A 10/100/1000M Smart Switch
3.1.1 Desktop Installation
3.1.2 Rack-Mount Installation
3.1.3 Installing Network Cables
3.1.3.1 Station Connection with Twisted-Pair Cable
3.1.3.2 Switch to Switch Connections with Twisted-Pair Cable
3.1.3.3 Network Application
4. Switching Operation
4.1 MAC Address Table & Learning
4.2 Filtering and Forwarding
4.3 Store and Forward
5. Console Program
6. Product Specifications
4
1. Unpacking Information
Thank you for purchasing the SP659A 10/100/1000 Mbps Smart Switch.
Before you start, please check all the contents of this package.
The product package should include the following:
1. SP659A 10/100/1000Mbps Gigabit Smart Switch
2. Console Cable
2. Power Cord
3. Screws and Rubber foot
4. Rack-mount Brackets
5. Quick Installation Guide
6. User’s Manual Disk
5
2. Introduction To SP659A 10/100/1000M Smart Switch
2.1 General Description
Micronet SP659A is a powerful, high-performance 10/100/1000 Mbps Fast
Ethernet and Gigabit switch, with all 24 ports capable of 10 or 100Mbps
auto-negotiation operation (NWay) , which means the switch could
automatically negotiate with the connected pa rtners on the network speed and
duplex mode. Moreover, the 10/100Mbps auto-sensing ability provides an easy
way to migrate 10Mbps to 100Mbps networks with no pain. Compared to the
shared 10Mbps or 100Mbps networks, the switch delivers a dedicated
10/100Mbps connection to every attached client with no bandwidth congestion
issue.
Another two are Gigabit copper ports, which also support auto-negotiation
operation, auto MDI crossover func tion and full-duplex mode. They are idea l for
micro-segmenting large networks into smaller , connected subnets for improved
performance, enabling the bandwidth demanding multimedia and imaging
applications. The Gigabit ports also provide the fat pipe to the servers or
backbone connection for boosting the total system performance.
The switch also supports more value-added function include port trunk
and virtual LAN. Port trunk function could be used to build up a fat pipe up to
800Mbps between switches that will solve the bandwidth bottleneck on
backbone connection. Port- based virtual LA N provides system security f unction,
which keeps the resources only could be shared in the same virtual group and
all the other nodes do not belong to the group can not a ccess the resources.
Store-and-forward switching mode promises the low latency plus
eliminates all the network errors, including runt and CRC error packets. To
work under full-duplex mode, tr ansmission and reception of the frames can
occur simultaneously without causing collisions as well as double the network
bandwidth.
The switch is plug-n-play without any software to configure and also fully
compliant with all kinds of network protocols. More ove r, the rich diagnostic
LEDs on the front-panel for providing the ope rating status of individual port
and whole system.
6
The switch can use the following types of cabling:
10BASE-T: Category 3, 4 or 5 UTP/STP
100BASE-TX: Category 5 UTP/STP
1000BASE-T: Category 5 or Category 5E UTP/STP
Category 5E cable is preferred to be using with this product in structured
wiring environments. This will ensure correct operation of all ports at
10Mbps ,100Mbps or 1000Mbps.
2.2 Key Features
The switch provides the following key features:
Complies with 10BASE-T specifications of the IEEE802.3 standard
Complies with 100BASE-TX specifications of IEEE802.3u standard
Complies with 1000BASE-T specifications of IEEE802.3ab standard
Twenty-four RJ-45 ports for 100Base-TX and 10Base-T connectivity
Two RJ-45 ports for 10Base-T, 100Base-TX and 1000Base-T connectivity
Supports NWay protocol for speed (10/100Mbps) and duplex mode
(Half/Full) auto-detection on twenty-four 10/100Mbps ports
The Gigabit ports support NWay protocol for speed (10/100/1000Mbps)
and full-duplex mode only
Supports auto MDI-X function on all ports
Supports one RS232 port for basic management
Wire-speed packet filtering and forwarding rate
Supports port trunk and VLAN function
Store-and-forward architecture filters fragment & CRC error packets
Supports 16K MAC address entries in whole system
12MBytes buffer memory
Supports extensive LED indicators f or network diagnostics
Internal universal switching power supply (100 ~ 240VAC)
FCC Class A, CE
2.3 The Front Panel
The front panel of the switching hub is shown below.
7
The auto-negotiation feature of the switch allows each port of the device
running at one of the following four opera t ion modes:
Port Speed Duplex Mode
Full-duplex 100 Mbps
Half-duplex
Full-duplex
10/100M
10 Mbps
Half-duplex
1000 Mbps Full-duplex
100 Mbps Full-duplex
Gigabit
10 Mbps Full-duplex
Each port supports auto MDI-X capability that is the port could connect
either the PC or hub without any cable adjustment.
The rich diagnostic LEDs on the front-p anel can provide the operating
status of individual port and whole system. The following table is a summary
for LEDs definition.
Type LED Status Operation
Steady Green Power is on System Power
Off Power is off
Steady Green Connected as 100Mbps
Blinking Green There is traffic transverses the port at
100Mbps
Steady Amber Connected as 10Mbps
Blinking Amber There is traffic transverses the port at
10Mbps
Speed/Link/
Act
Off No connection
Steady Amber Full-duplex mode
Blinking Amber There is a collision
10/100M
Ports
FDX/COL
Off Half-duplex mode
Steady Green Connected as 1000Mbps 1000M
Off Not connected as 1000Mbps
Steady Green Connected as 100Mbps 100M
Off Not connected as 100Mbps
Steady Green Connected as 10Mbps 10M
Off Not connected as 10Mbps
Steady Green The port is connected
Blinking Green There is traffic transverses the port
Link/Act
Off No connection
Steady Green Full-duplex mode
1000M
Ports
FDX
Off No connection or link error
8
2.3.1 System LEDs
System LED indicators are located on the front panel for showing the
operating status of the whole device.
2.3.1.1 Power LED
This indicator lights green when the hub is receiving power; otherwise, it is
off.
2.3.2 10/100 Port LEDs
10/100 Port LED indicators are located on the front panel for showing the
operating status of each 10/100 Mbps port.
2.3.2.1 Speed/Link/Act LED
Every port has a Speed/Link/Activity LED. Steady light (link state)
indicated that the port has good linkage to its associated device. Flashing
indicates there is traffic transverses the port. The following is table for LED
definition.
If the port is connected but the Speed/Link/Activity LED is dark, check the
following items:
1. The switching hub and the connected device’s power are on or not
2. The port’s cable is firmly seate d in its connectors in the switching hub and in
the associated device.
3. The connecting cable is good and with c or rect type
4. The connecting device, including any network adapter is functioning.
2.3.2.2 FDX/COL LED
A collision occurs when two stations within a collision domain attempt to
transmit data at the same time. Intermittent flashing amber of the collision LED
is normal; the contending adapters resolve each collision by means of a
wait-then-retransmit algorithm. Frequency of collisions is an indicator of heavy
traffic on the network.
If the FDX/COL light amber which means the port is under full-duplex
operation or dark for half -duplex mode.
9
2.3.2.3 Gigabit LED
The Gigabit ports support 1000BASE-T media connection and diagnostic
LEDs. There are five LEDs for gigabit switching port including 10M, 100M,
1000M, FDX, Link/ACT.
2.4 The Rear Panel
The rear panel of the hub is shown below
2.4.1 Power Connecting
For compatibility with electric service in most areas of the world, the
switching hub’s power supply automatically adjusts to line power in the range
100~240 VAC and 50~60 Hz.
Plug the female end of the power cord firmly into the receptacle on the rear
panel of the switching hub. Plug the other end of the power cord into an electric
service outlet then the power will be ready.
2.4.2 Console Port
Through the console port, it provides rich diagnostic information includes
network statistics, link status and system setting. The operating mode of the
console port is:
DCE (terminal mode)
9600 (baud rate)
N (non-stop bit)
8 (8 data bits)
1 (1 parity bit)
You could use a normal RS-232 cable connect to the console port on the
device. After the connection, you could run any terminal emulation program
(Winterm, Telix, … and so on) to enter the startup screen of the device. All the
detail software operation, please refer to “Console Program” session.
10
3. Installing &Using SP659A 10/100/1000M Smart Switch
3.1 Installing The SP659A 10/100/1000M Smart Switch
The switch does not require software c onfiguration. Users can immediately
use most of the features of this product simply by attaching the cables and
turning the power on.
3.1.1 Desktop Installation
For desktop installation, the switch needs to put on a c lean, flat desk or
table close to a power outlet. Plug in all networ k c onnections and the power
cord, then the system is ready.
When deciding where to put the switch then you must ensure:
It is accessible and cables can be connected easily
Cabling is away from - Sources of electrical noise such as radio, transmitters,
broadband amplifiers, and fluorescent lighting fixtures.
Water or moisture can not enter the unit
Air flow around the unit and through the vents in the side of the case is not
restricted (company recommend that you provide a minimum of 25mm
inch clearance)
To prolong the operational life of your units:
Never stack units more than eight sets high if freestanding.
Do not place objects on top of any unit or stack
Do not obstruct any vents at the sides of the case
3.1.2 Rack-Mount Installation
The switch may standalone, or may be mounted in a standard 19-inch
equipment rack. Rack mounting produces an orderly installation when you have
a number of related network de vic es. The switch is supplied with two mounting
brackets and screws. These are used for rack mounting the unit.
Rack Mounting the Switch
The switch should be able to fit in the 19 inches rack.
1. Disconnect all cables from the switch before continuing.
2. Place the unit on a hard, flat surface with the front facing toward you.
3. Locate a mounting bracket ove r the mounting holes on one side of the unit.
4. Insert the screws and fully tighten with a suitable screwdriver.
5. Repeat the two previous steps for the other side of the unit.
11
6. Insert the unit into the 19" rack and secure with screws (not provided).
7. Reconnect all cables.
3.1.3 Installing Network Cables
After placing the switch on the desktop, then we need to know how to
connect the device to network.
3.1.3.1 Station C onnections with Twisted-Pair Cable
Connect each station to the switch by a Ca te gory 5 or Category 5E
twisted-pair cable (straight-through or cross-over cable). Plug one RJ-45
connector into a front-panel por t of the switch, and plug the other RJ-45
connector into the station’s network ada p ter.
3.1.3.2 Switch to Switch Connections with Twisted-Pair Cable
In making a switch to switch connection, you could use any port to c onnect
another switch with straight-through or cross-over cable. As the 10/100Mbps
ports support auto MDI-X function, so the connec tion is independent of cable
type. allow using a straight cable to make a switch to switch connection.
In order to increase the bandwidth between switch and switch, you could
enable the port trunk function or Gigabit ports to c onnect each other.
12
4. Switch Operation
4.1 MAC Address Table and Learning
The switch is implemented with a MAC address table which is composed
of many entries. Each entry is used to store the address information of network
nodes on the network, including MAC a ddress, port ID, etc. The information is
the most important base to do packet filtering and forwarding.
When one packet comes in from any port, the switch will learn the source
address, port ID, and the other related information in address table. Therefore,
the content of the MAC table will update dynamically.
4.2 Filtering and Forwarding
When one packet comes in from any port of the switch, it will check the
destination address besides the source address learning. The switch will look up
the address table for the destination address. If not found, this pa cket will be
forwarded to all the other ports except the port in which this packet comes. If
found, and the destination address is located at different port from this packet
comes in, the packet will be forwarded to the port where this destination
address is located according to the information of address ta ble. But, if the
destination address is located at the same port as this packet comes in then this
packet will be filtered.
4.3 Store and Forward
Store-and-forwar d is one kind of packet-forwarding methodology. As a
store-and-forward switching hub, it will store the complete packet in the
internal buffer and do the complete error checking before transmitting to the
network. Therefore, no error packets will disturb the network. It is the best
choice when a network needs efficiency and stability.
13
5. Console Program
The switch has an RS-232 console port for direct console management
Pin Description
1 DCD (Data Carrier Detect)
2 RX (Receive)
3 TX (Transmit)
4 DTR (Data Terminal Ready)
5 GND (Ground)
6 DSR (Data Set Ready)
7 RTS (Request To Send)
8 CTS (Clear To Send)
9 N/A
(RS-232 DB-9, DCE/female connector)
When connecting a terminal directly to the switch, use a serial RS232
(straight through) cable.
Main Menu:
After power on, the Switch will run the Power-On-Self-Test (POST) with the
screen as following. There are five main functions listed in the [Main Menu]
screen. Each function could be activated by key-in the number (1-5) of item
without pressing [Enter] key.
5 1
9 6
14
1. Port Status/Configuration
This function is used to check operating status of all ports and setup the port
configuration, like half/full duplex mode and auto-negotiation.
2. VLAN Status/Configuration
The device supports six port-based VLAN groups (1, 2, 3, 4, 5 and 6) and the
group overlap is allowed. From this item, you could view current VLAN setting
and make modification.
3. Trunk Status/Configuration
This item is used to review and setup the port trunk function. There are total
seven trunk groups could be configured as the following table:
Trunk Group Trunk Ports
Trunk Port_1 1, 2, 13, 14
Trunk Port_2 3, 4, 15, 16
Trunk Port_3 5, 6, 17, 18
Trunk Port_4 7, 8, 19, 20
Trunk Port_5 9, 10, 21, 22
Trunk Port_6 11, 12, 23, 24
Trunk Port_7 25, 26
15
4. Factory Reset
If you face some problem on current setting and want to make the system go
back to the initial state, you can use factory reset.
5. Warm Start
System will reboot after selecting this item.
The following is the function keys to navigate the console program screens.
To do this … Control Key
Return to previous page or
Abort current setting
Do not key-in any numeric key
but [Enter]
Select an item Numeric key + Enter
The following sections are detail content of each sub-screen of [Main Menu]
console page.
Port Status/Configuration Screen
This screen indicates each 10/100Mbps port’s status, including
auto-negotiation, 100M full-duplex, 100 half-duplex, 10M full-duplex, 10
half-duplex. Symbol “V” means the status of each port. You could change the
setting of each port by entering the port number (1-24) then press [Enter] key.
Gigabit ports (25-26) support auto-negotiation mode and have capabilities of
10/100/1000Mbps full duplex mode.
16
Note :
If you press [Enter] key without selecting any number of function in a dvance, the system
will return to the previous screen.
Port Selection Screen
You could select 1-5 to setup duplex mode for each port or select [6] key to
return to the previous screen.
The AUTO option means the NWAY function is enabled and the switching
port will auto-negotiate the speed and d uplex mode with the connected partner.
Note :
If you press [Enter] key without selecting any number of function in a dvance, the system
will return to the previous screen.
VLAN Status/Configuration Screen
This switch provides six VLAN groups. Symbol “V” indicates that the port
belongs to this VLAN group. Select port number (1-26) to change the setting of
VLAN function of each port.
Note :
If you press [Enter] key without selecting any number of function in advance, the system
will return to the previous screen.
17
VLAN Group Setting Screen
You can select [1] key to add this port to VLAN or select [2] key to remove
this port form the VLAN. If you want to return the previous screen or abort the
setting, please press [3] key.
Trunk Status/Configuration Screen
This screen indicates the trunk status of all ports. You could select 1-7 to
enable/disable port trunk function of each port. If you want to return to the
previous screen, please select [8] key.
18
Trunk Group Setting Screen
After selecting port number, you can set trunk group function enable/disable
of each port. Select [1] key to disable port trunk function or select [2] key to
enable the function. If you want to return to the previous screen or abort the
setting, please press [3] key.
19
Factory Default Scree n
Warm Start Screen
20
6. Product Specifications
Standard
IEEE802.3, 10BASE-T
IEEE802.3u, 100BASE-TX
IEEE802.3ab, 1000BASE-T
Interface
RJ-45 x 24 10/100 auto MDI-X switching ports
RJ-45 x 2 10/100/1000 auto MDI-X switching ports
One RS-232 console port
Cable Connections
RJ-45 (10BASE-T) : UTP Cat. 3,4,5
RJ-45 (100BASE-TX) : UTP Cat. 5
RJ-45 (1000BASE-T): UTP Cat. 5 or Cat. 5E (preferred)
Network Data Rate
Auto-negotiation (10Mbps, 100Mbps)
Gigabit Ethernet (10/100/1000Mbps)
Transmission Mode
Auto-negotiation (Full-duplex, Half-duplex)
LED indications
System
Power
10/100Mbps Port
Speed/Link/Activity
FDX/COL
1000Mbps Port
10M
100M
1000M
FDX
ACT
System Buffer Memory
12MByte
MAC Address Table
16K entries
Filtering/Forwarding
Rate
10Mbps: 14,880pps/14,880pps
100Mbps: 148,800pps/148,800pps
1000Mbps 1,488,100pps
Emission
FCC Class A, CE
Operating Temperature
0
0
~ 500C (320 ~ 1220F)
Operating Humidity
10% - 90%
Power Supply
100~240 VAC, 50/60 Hz
Loading...