Micronet SP3366 Quick Install Guide
Step 3. In DOS command, type 'ipconfig' to view information on
LAN connection. Ensure the IP address and subnet mask
are on the same range as the modem router.
Default Values
IP Address
Subnet Mask
Username
Password
Web-based User Interface
The SP3366 Modem Router provides web-based configuration
allowing users to configure from a wired workstation.
Step 1. Enter SP3366's default IP into the web browser to access
web-based settings.
192.168.1.254
255.255.255.0
'admin'
'admin'
Step 2. Login page will appear to prompt users to enter the
username and password.
Step 3. Click <Quick Start> to initiate quick setup for configuring
general network system information. Select to automatically
detect or manually set WAN connection type.
Step 4. If user selects 'Auto', the system will scan for possible WAN
connection type with ISP devices.
5
Step 5. Enter the Internet account details supplied by the ISP.
Step 6. The device will save configuration to Flash and initiate
Internet access. For detail explanation of each WAN
Step 6.
connection types, please consult the user manual in the
Step 6.
product CD.
Step 6.
Parameter
PPPoE
PPPoA
MPoA
IPoA
Pure Bridge
Description
ISP requires user to use Point-to-Point Protocol
over Ethernet (PPPoE) connection
ISP requires user to use Point-to-Point Protocol
over ATM (PPPoA) connection
ISP requires user to use Multi-Protocol
Encapsulation over AAL5 (MPoA) connection
ISP requires user to use Classic IP and ARP
over ATM (IPoA) connection
Device will act as modem only equipment to
prevent conflict with other routers
6
Quick Installation Guide
ADSL2+ VPN Modem Router
Model No.: SP3366
P/N: 2300-0536
7
Web: www.micronet.com.tw
Introduction
Micronet SP3366, ADSL2+ VPN Modem Router, delivers highly
reliable and scalable network environment. The model has
incorporated both modem and router functions into a single unit with
VPN support. The modem router allows multiple network devices to
share the single Internet connection via ADSL. Sustain network
security via router's in-built firewall and DMZ functions. In addition,
the scope of the network can be easily expanded by connecting the
router to a hub or switch.
Package Contents
Please verify the following items are in the package:
• ADSL2+ VPN Modem Router
• Quick Installation Guide
• Manual CD
• RJ-45/RJ-11 Cables
• RJ-45/RS232 Console Kit
• Power Adapter
Note: Contact your dealer immediately if any of the above items are
missing, damaged, or if the unit does not work.
Tour of the Product
Front Panel
LED Status
Power
Green
Red
Off
LAN
Green
(1-4)
Amber
Flashing
Mail
Flashing
Line
Green
ADSL
Green
Red
1. Power (DC 12V, 1A): Power connector for connecting to
1. Power (DC 12V, 1A):
2. On/Off: For powering device on and off.
3. Reset: Press and hold this button for more than 6 seconds to reset
Reset:
4. LAN 1~4: Local Area Network (LAN) ports for 1 to 4 ports.
5. ADSL: Connection to RJ-11 telephone line for Internet.
settings back to factory default.
Description
Device is switched on
System failure. Restart device
No Power
LAN port is connected and operating at 100Mbps
LAN port is connected and operating at 10Mbps
Data is being sent or received
Received emails in the inbox
Device successfully connected to
DSLAM (line sync)
WAN IP successfully assigned
Unable to obtain WAN IP from ISP
Rear Panel
power source.
Hardware Installation
To install the SP3366 Modem Router, please perform the following
steps:
Step 1. Connect the ADSL port of modem router by telephone
Step 1.
cable (RJ-11) to an outlet or splitter.
Step 2. Connect the LAN port to an active PC, switch, or hub using
Step 1.
an Ethernet cable (RJ-45).
Step 3. Connect the 12V DC power adapter to a power outlet.
Step 4. Connect the adaptor to the power port on the back of the
Step 1.
router. Switch device on using On/Off button.
Step 5. Check the LED indicators to verify that the device is
Step 1.
detecting connection on Line and LAN.
Warning: Using an alternate power supply, other than the one
Warning:
supplied, may cause the router to malfunction.
3 4
21
Configuration
Follow the steps below to configure and set up modem router. A
computer with wired Ethernet connection to the router is required.
IP Address Configuration
PC/Notebook must belong in the same IP range and subnet. Follow
the steps below to configure IP settings for LAN PC.
Step 1. In the control panel,
double click on
'Network Connections'.
Double click on the local
area connection (e.g.
LAN). The following
screen will appear.
Highlight 'Internet
Protocol (TCP/IP)' and
click on 'Properties'.
Step 2. Select 'Obtain an IP
address
automatically' and
'Obtain DNS server
address
automatically', then
click <OK>.
Loading...