Micronet SP3361 Quick Install Guide

Hardware Installation

1. Plug the provided RJ-11 cable into ADSL port on the router and

1.

insert the other end into Modem jack on splitter or phone jack on

1.

the wall.

2. Take the RJ-45 Cable, plug one end into LAN port on the router

1.

and other end into the PC's Ethernet port.

3. Plug power adapter to POWER jack on the router and the other

end to a power outlet. Press On/Off to power on this router.

1.

Access Management Web UI

1. Check the computer's network has been configured to get IP

1.

automatically or has IP in the same network of 192.168.1.0.

2. Verify IP status by DOS command (ipconfig for Windows

1.

2000/XP or winipcfg for Windows 95/98).

3. Open Internet browser, enter the default IP address in the URL

1.

line, Press Enter to browse the router.

4.

The authentication page pops up. Key in the password then click

1.

OK to access the web UI.

Default IP Address : 192.168.1.1

User name : admin

Password : admin

PS.: For more inforamtion please refer the manual on the CD.

Configuring Connection Mode

Here describes the settings of PPPoE/PPPoA. Please refer the

manual on the CD if other connection modes adapted.

1. Prepare the ADSL account information provided from your ISP.

1.

It should include the items list below:

a. Encapsulation: PPPoE, PPPoA

b. Multiplex: VC or LLC

c. Virtual Circuit ID: VPI/VCI

d. User name and password

2. Once login the web UI, open Quick Start and click RUN

1.

WIZARD. Quick Setup page will pop up on the screen.

3. Click Next then enter the new password and confirm the entry.

4. Click Next. Select time zone of your location then click Next.

5. Select PPPoE/PPPoA then click Next.

6. Type in your user name, password, VPI/VCI values and select

1.

the correct Encapsulation mode. Click Next twice to save the

1.

setting in this router. Wait the window turns to next page, click

1.

Close to close the page.

7. Under Maintenance, find Time Zone page, click Save to enable

1.

SNTP service thus this router can get the current time from

1.

Internet time server.

8. Go to Status. Scroll down the page, the ADSL line has been set

1.

up while WAN table showing CONNECTED and getting IP from

1.

ISP.

9. Now, client can surf Internet via this router.

5

FCC Certifications

This device complies with Part 15 of the FCC rules. Operation is

subject to the following two conditions:

(1) This device may not cause harmful interference, and

9.

(2) This device must accept any interference received,

9.

including interference that may cause undesired operation.

9.

CE Mark Warning

This is a Class B product. In a domestic environment, this product

may cause radio interference, in which case the user may be

required to take adequate measures.

6

Quick Installation Guide

ADSL2+ Modem Router

Model No.: SP3361/SP3364F

P/N: 2300-0444

7

Web: www.micronet.com.tw

Introduction

This device is compatible with the new ADSL2+ standards and

delivers on high performance and easy to use. It lets users

experience faster communication speed than ever and enjoy in new

Triple Play services (Voice, Data and Video) more smoothly.

• Support IP routing to share a single account with multiple

workstations

•

• The USB supports Windows 98/Me/2000/XP/Vista32 and MAC

OS 10.1/10.2 and above

•

Front Panel

Package Contents

• ADSL2+ Modem Router • Quick Installation Guide

• Manual CD • Power Adapter

• RJ-45 Cable • RJ-11 Cable

• USB Cable

SP3361

LED

ADSL

Features

• Compliant with ADSL and ADSL2/2+ standards

• Support up to 8 VCs (virtual circuits)

• Provide 1 RJ-11 port for ADSL connection, 1 RJ-45 Ethernet

•

LAN port and 1 USB port (SP3361)

• Provide 1 RJ-11 port for ADSL connection, 4 RJ-45 Ethernet

•

LAN ports of 10/100M and 1 USB port (SP3364F)

• Support NAT, DHCP protocol, DMZ host and UPnP

• Support port forwarding, virtual server and DDNS

• Support management from local and remote site by web UI and

•

Telnet configuration

• Support MIB-II for SNMP standard management

• Support SNTP to obtain current time from specified time server

DATA

LAN

USB

PWR

Description

When connection with Internet (ADSL Connected)
is established, this LED will light up.
When this LED is flashing: NO ADSL physical
connection

When router is transferring data between Internet
and router, this LED will be flashing.

When connection 10/100MB with end user is
established, this LED will light up. When router is
transferring data between router and end user,
this LED will be flashing.

When an active USB cable is connected with router,
this LED will light up.

When an active power adapter is connected with router,
this LED will light up.

1 2

SP3364F

LED

PWR

USB

LAN

(1~4)

ADSL When connection with Internet (ADSL Connected)

Description

When an active power adapter is connected with
router, this LED will light up.

When an active USB cable is connected with router,
this LED will light up.

When LAN port connection with PC or Switch / Hub
is established, this LED will light up.

is established, this LED will light up.
When this LED is flashing: NO ADSL physical connection.

Real Ports

SP3361

Connector

LINE

USB
Reset
LAN
POWER
ON/OFF

SP3364F

Description

Connect with telephone line.

Connect with USB cable.
Reset button.
Connect with Ethernet Cable to Switch Hub or PC.
Connect with power adapter.

Power switch button.

Port

ON/OFF
PWR Connect with power adapter
LAN(1~4)
RESET
USB
ADSL

3

Description

Power switch button

Connect with Ethernet cable to switch/hub or PC
Reset to default value
Connect with USB cable to PC
Connect with phone cable

4