User Manual
ADSL2+ Modem Router
Model No. SP3361
Web: www.micronet.com.tw ; www/micronet.info
FCC Certifications
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
CE Mark Warning
This is a Class B product. In a domestic environment, this product
may cause radio interference, in which case the user may be required
to take adequate measures.
Copyright
Copyright © 2005 by this company. All rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a
Contents
Chapter 1. Introduction ............................................................5
retrieval system, or translated into any language or computer
language, in any form or by any means, electronic, mechanical,
magnetic, optical, chemical, manual or otherwise, without the prior
written permission of this company.
Disclaimer
This company makes no representations or warranties, either
expressed or implied, with respect to the contents hereof and
specifically disclaims any warranties, merchantability or fitness for
any particular purpose. Any software described in this manual is sold
or licensed "as is". Should the programs prove defective following
their purchase, the buyer (and not this company, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and
any incidental or consequential damages resulting from any defect in
the software. Further, this company reserves the right to revise this
publication and to make changes from time to time in the contents
hereof without obligation to notify any person of such revision or
changes.
All brand and product names mentioned in this manual are
trademarks and/or registered trademarks of their respective
holders.
1.1 System Requirement.................................................................5
1.2 Package Contents..................................................................... 5
Chapter 2. Features ...................................................... 7
2.1 ADSL Compliant ........................................................................ 7
2.2 ATM Protocols and Encapsulations ..........................................7
2.3 PPP Support .............................................................................8
2.4 Bridging / Routing Support........................................................8
2.5 IP Management......................................................................... 8
2.6 Security .....................................................................................9
2.7 Device Management ................................................................. 9
2.8 Interface ....................................................................................9
Chapter 3. Hardware................................................... 10
3.1 Front Panel Indicators and Description...................................10
3.2 Back Panel .............................................................................. 11
3.3 Connect Related Devices ....................................................... 11
Chapter 4. Connection................................................ 13
4.1 Setup ADSL Router via Ethernet Cable ..................................13
4.2 Setup ADSL Router via USB Cable ........................................13
4.3 Configure TCP/IP .................................................................... 23
4.4 USB Device Driver Installation on MAC OS............................39
2
3
Chapter 5. Configuration............................................ 48
5.1 Login .......................................................................................48
5.2 Quick Start...............................................................................50
5.3 Interface Setup........................................................................51
5.3.1 Interface .............................................................................51
5.3. 2 LAN ....................................................................................53
5.4 Advanced Setup......................................................................55
5.4.1 Routing...............................................................................55
5.4. 2 NAT..................................................................................... 55
5.5 Access Management...............................................................57
5.5. 1 ACL..................................................................................... 57
5.5.2 IP Filter ...............................................................................58
5.5. 3 SNMP ................................................................................. 59
5.5. 4 UPnP .................................................................................. 60
5.5. 5 DDNS .................................................................................61
5.6 Maintenance............................................................................ 62
5.6.1 Administration.....................................................................62
5.6.2 Time Zone ..........................................................................62
5.6.3 Firmware ............................................................................63
5.6.4 System Restart...................................................................65
5.6.5 Diagnostic...........................................................................65
5.7 Status ......................................................................................66
5.7.1 Device Info. ........................................................................66
5.7.2 System Log ........................................................................68
5.7.3 Statistics .............................................................................70
Chapter 1. Introduction
This device is a full-featured ADSL2+ modem router that provides
Ethernet direct connections to individual PCs or local area network
with 10/100 Base-T Ethernet. This product uses advanced ADSL
chipset solution with complete set of industry standard features and
high-speed ADSL, ADSL2 and ADSL2+ Internet access solution for
SOHO and residential users. User can enjoy higher quality
multi-media and real-time applications such as Video-on-Demand,
online gaming and other bandwidth consuming services. Also the
feature-rich routing functions are integrated to ADSL/ADSL2+ service
for existing corporate or home users seamlessly.
1.1 System Requirements
z Pentium III 266 MHz processor or higher
z 128 MB RAM minimum
z 20 MB of free disk space minimum
z Ethernet Network Interface Controller (NIC) RJ45 Port
z USB Port
z CD drive
1.2 Packag e Contents
z ADSL2+ Modem Router
z RJ-45 Ethernet cable
z RJ-11 Phone cable
4
5
z USB Cable (for dual mode router only)
z Powe r Adapter
Chapter 2. Features
z Driver and Manual CD
z Quick Installation Guide
If any of above items is missing or d amaged, please conta ct
your local dealer immediately.
2.1 ADSL Compliant
z ANSI T1.413 issue 2
z ITU-T G.992.1 (G.dmt)
z ITU-T G.992.2 (G.lite)
z G.994.1 (G.hs, Multimode)
z ITU-T G.992.3 (ADSL2 G.dmt.bis)
z ITU-T G.992.4 (ADSL2 G.lite.bis)
z ITU-T G.992.5 (ADSL2+, Annex A, B, I, J, L & M)
2.2 ATM Protocols and Encapsulations
z Support up to 8PVCs
z ATM Forum UNI 3.1/4.0 PVC
z Traffic Shaping UBR, CBR, VBR-nrt
z Multi Protocol over AAL5 (RFC1483 / 2684)
z Classical IP over ATM (RFC 1577)
z OAM F4 an d F5 se gment end-to-end lo opback, AIS, and
RDI OAM cells
z VC and LLC Multiplexing
z VPI is 0~255 and VCI is 32~65535
6
7
2.3 PPP Support
2.6 Securit y
z PPP over Ethernet (RFC 2516)
z PPP over ATM (RFC 2364)
z PPP over PAP (Password Authentication Protocol;
RFC1334)
z PPP over CHAP (Challenge Authentication Protocol;
RFC1994)
2.4 Bridging / Routing Support
z Ethernet to ADSL self-learning Transparent Bridging
(IEEE 802.1D)
z IP routing-RIPv2 (backward compatible with RIPv1)
z Static IP routing
z IGMP Proxy
z IP Multicast IGMP v1/v2
z ICMP support
z MIB II support (RFC 1213)
2.5 IP Management
z NAT (Network Address Translation)
z PAT (Port Address Translation)
z DHCP Server / Relay / Client
z Virtual Server and DMZ
z DNS Proxy / Relay
z PAP (Password Authentication Protocol; RFC1334)
z CHAP (Challenge Authentication Protocol; RFC1994)
z Password Protected System Management
z VPN (IPSec, PPTP, L2TP) Pass-Through
z Built in NAT Natural Firewall
z Web page Content Filtering
2.7 Device Management
z Web-based GUI Configuration / Management
z Command-line Interpreter (CLI)
z Telnet Remote Management
z Firmware upgrade via FTP / TFTP
z SNMP Support
z Built-in Diagnostic tool
2.8 Interface
z One USB port compliant with USB v1.1, full speed
(12Mbps)
z One RJ45 port compatible with IEEE 802.3/802.3u,
10/100Mbps auto selection
z One RJ11 port for ADSL connection
z One power switch button for turn ON/OFF
z One reset button for restoration of factory default setting
z DD NS
z UPnP
8
9
Chapter 3. Hardware
3.2 Back Panel
3.1 Front Panel
Front panel has LED indicators to display the operating status.
Descriptions of LED status
When connection with Internet (ADSL Connected) is
ADSL
DATA
LAN
USB
PWR
established, this LED will light up.
When this LED is flashing: NO ADSL physical
connection
When router is transferring data between Internet and
router, this LED will be flashing.
When connection 10/100MB with end user is
established, this LED will light up. When router is
transferring data between router and end user, this LED
will be flashing.
When an active USB cable is connected with router, this
LED will light up.
When an active power adapter is connected with router,
this LED will light up.
Descriptions of All Connectors
LINE Connect with telephone line.
USB Connect with USB cable.
RESET Reset button.
LAN Connect with Ethernet Cable to Switch Hub or PC
POWER Connect with power adapter
ON/OFF Power switch button
3.3 Connect Related Devices
1) Connect Router to LINE
Plug the provided RJ-11 phone cable into LINE port on the
back panel of the router and insert the other end into splitter
or wall phone jack.
2) Connect Router to LAN
Plug RJ-45 Ethernet Cable into LAN port on the back
panel of the router and insert the other end of the Ethernet
cable on your PC’s Ethernet port or switch / hub.
3) Connect Router to Power Adapter
Plug Power Adapter to POWER port on the back panel of
10
11
the router and the other end to a power outlet.
4) Press ON/OFF button to start the router
Chapter 4. Connection
5) If connect the router via USB cable, plug the provided USB
cable into USB port on the back panel of the router and
insert the other end of the USB cable on your PC.
Warning! Only use the power adapter provided in the pac kage,
otherwise it may cause hardware damage.
This ADSL modem router can be connected with PC through either
Ethernet cable or USB cable. After connection is established,
configure the host PC to be a DHCP client. Repeat the same steps for
every host PC on the network which uses DHCP function on this
router. It also accepts host PC using fixed virtual IP which is resided
in the same sub network of this router.
4.1 Setup ADSL router via Ethernet Cable
If there is an available LAN card present on PC, simply connect ADSL
router and PC through the Ethernet cable. Once Internet connection
is established, you could browse the Web through the Ethernet cable.
4.2 Setup ADSL router via USB Cable
PC can be connected ADSL router via USB cable while no LAN card
12
present on it. USB cable acts as another LAN connection in this
scenario. Once Internet connection is established, you could browse
the Web through the USB cable.
13
USB Device Driver Installation
For windows 98SE and ME:
Step 1: Connect ADSL Router and PC with USB cable.
Step 2: Once “Add New Hardware Wizard” window pops out, click
“Cancel”.
Step 3: Browse your installation CD and direct the device drive path
Step 4: Choose Setup Language and click “Next” to continue.
Step 5: Click “Next” to continue.
which depends on your operating system. Then, double-click
“Setup.exe” to execute the installation process.
14
15
Step 6: Select the setup type to install and click “Next” to continue.
Step 8: Select “Yes, I want to restart my computer now” to restart your
computer and click “OK”.
Step 7: Click “Next” to continue.
16
Step 9: Click “Finish” to exit the wizard.
17
Step 10: After complete the installation process, the system will ask to
For Windows 2000 and XP:
restart your computer. Please click “Yes” to reboot it.
After OS boots up, go through “Start Æ Settings Æ Control Panel
Æ System Æ Device Manger” to check if USB device is installed
properly,
Step 1: Connect ADSL Router and PC with USB cable.
Step 2: Once “Found New Hardware Wizard” window pops out,
chooses “Install from a list or specific location
(advanced)” and click “Cancel”:
Step 3: Browse your installation CD and direct the CD drive path.
Then, double-click “Setup.exe” to execute the installation
process.
18
19
Step 4: Choose Setup Language and click “Next” to continue.
Step 6: Select the setup type to install and click “Next” to continue.
Step 5: Click “Next” to continue.
Step 7: Click “Next” to continue.
20
21
Step 8: Click “Finish” to exit the wizard.
For Windows XP:
Go through “Start Æ Control Panel Æ System Æ Hardware Æ
Device Manager” to check if USB device is installed properly.
FOR Windows 2000:
Go through “Start Æ Settings Æ Control Panel Æ System Æ
Hardware Æ Device Manager” to check if USB device is installed
properly.
4.3 Configure TCP/IP
For Windows 98SE and ME
Step 1: Click Start then Settings and choose Control Panel
Step 2: Double click Network icon.
Step 3: Select Configuration tab, then choose TCP/IP from the list of
installed network components and click Properties button.
22
23
Step 4: You can setup the following configurations in two methods:
1) Select Gateway tab and click OK.
‘
Option1
: Get an IP from router automatically.
Choose Obtain an IP address automatically option in the
next window.
24
25
2) Select DNS Configuration tab and select Disable DNS then
Option2
: Configure IP manually.
click OK.
1) Select Specify an IP address, set default IP address for
the router is 192.168.1.1, so use 192.168.1.x (x is a
number between 2 to 254) for IP Address field and
255.255.255.0 for Subnet Mask field.
26
27
2) Select Gateway tab and add default router IP address
3) Under DNS Configuration tab, select Enable DNS and add
(192.168.1.1) in the New gateway field and click Add.
DNS values which provides by your local ISP in DNS
Server Search Order field then click Add.
28
29
For Windows 2000
Step 1: Right click My Network Places and select Properties in the
main window screen.
Step 2: Right click Local Area Connection (the local network hooked
up with ADSL router) and select Properties:
Step 3: Select Internet Protocol (TCP/IP) then click Properties.
Setup the following configurations in two methods:
30
31
Option1
: Configure IP automatically
Option2
: Configure IP Manually
Select Obtain an IP address automatically and Obtain DNS server
address automatically then click OK to complete IP configuring
process.
Select Use the following IP address and Use the following DNS
server addresses.
IP address: Fill in IP address 192.168.1.x (x is a number between 2
to 254).
Subnet mask: Default value is 255.255.255.0.
Default gateway: Default value is 192.168.1.1.
Preferred DNS server: Fill in preferred DNS server IP address.
Alternate DNS server: Fill in alternate DNS server IP address.
32
33
For Windows XP
Step 3: Right click Local Area Connection (local network your ADSL
Step 1: Click Start then select Control Panel in the main window
screen.
Step 2: Double click Network Connections icon.
hooked up with) then select Properties:
Step 4: Sele ct Internet Protocol (T CP/IP) then cli ck Properties to
configure IP with either option below.
34
35
Option1
: Configure IP address automatically
Option2
: Configure IP address manually
Select Obtain an IP address automatically and Obtain DNS server
address automatically:
Step 1: Select Use the following IP address and Use the following
DNS server addresses.
IP address: Fill in IP address 192.168.1.x (x is a number between 2
to 254).
Subnet mask: Default value is 255.255.255.0.
Default gateway: Default value is 192.168.1.1.
Preferred DNS server: Fill in preferred DNS server IP address.
Alternate DNS server: Fill in alternate DNS server IP address.
36
37
You can use ping command under DOS prompt to check if you have
4.4 USB Device Driver Installation on MAC OS
setup TCP/IP protocol correctly and if your computer has successfully
connected to this router.
Type ping 192.168.1.1 under DOS prompt and the following
messages will appear:
Pinging 192.168.1.1 with 32 bytes of data:
Reply from 192.168.1.1: bytes=32 times<2ms TTL=64
Reply from 192.168.1.1: bytes=32 times<1ms TTL=64
Reply from 192.168.1.1: bytes=32 times<10ms TTL=64
If the communication link between your computer and router is not
setup correctly, after you type ping 192.168.1.1 under DOS prompt
following messages will appear:
Pinging 192.168.1.1 with 32 bytes of data:
Reques t timed out.
Reques t timed out.
Reques t timed out.
Step 1: Once you insert the device driver CD disk, direct the path of
your MAC OS. Double-click the compressed “.zip” file to
unzip the file. Then, you will get a “.pkg” file.
Step 2: Double-click the “.pkg” file, the Trendchip ADSL modem
installer windows will appear. Click “Continue” to go next
process.
This failure might be caused by cable issue or something wrong in
configuration procedure.
38
39
Step3: Select a Destination to install the Trendchip ADSL Modem
software and click “Continue”.
Step 5: Click “Install” to begin the installation process.
Step 6: Enter your Name and Password for the system. Then, click
Step 4. Click “Continue” to go next process.
“OK” to continue.
40
41
Step7: Click “Continue Installation” to start installation.
Step 8: Click “Restart” to finish installing the software.
Step 9: After restart the PC, click “System Preferences” on the
bottom of the desktop.
Step 10: Click “Network” icon on the System Preferences windows.
42
43
Step 11: Once your Ethernet Adapter’ s button is “ Green”, it means
Step 12: Fill in TCP/IP IP address.
your ADSL Router is successful installed.
IP address: Fill in IP address 192.168.1.x
(x is a number between 2 to 254).
Subnet mask: Default value is 255.255.255.0.
Router: Default value is 192.168.1.1
44
45
Step 13: Go to “Applications” Æ double-click “Internet Explorer”
Step15: Entry of the username and password will be displayed.
icon.
Step14: Enter the default IP address http://192.168.1.1
Enter the default User ID and Password. The default login User ID of
the administrator is admin, and the default admin login password
is trendchip. Then, click “OK” to enter.
After you enter User ID and Password, the main webpage will show
as below.
46
47
Chapter 5. Configuration
ADSL Router supports a web-based (HTML) GUI to allow users to
configure router setting via Web browser.
5.1 Login
1) Launch the Web browser.
The main webpage will be displayed as below:
2) Enter the default IP address http://192.168.1.1
3) Entry of the username and password will be displayed. Enter
the default login
User Name and Password:
The default login User Name of the administrator is admin, and the
default login password is trendchip.
48
49
5.2 Quick Start
The Quick Start setup wizard includes four quick steps:
Click Quick Start to guide you to configure the device to connect your
ISP and have Internet access within minutes. This Quick Start helps
you connect to the Internet as easily as possible.
NOTE: It is a strong recommendation that using Quick Start to set
your ADSL settings.
1) Set your new password.
2) Choose your time zone.
3) Set your Internet connection.
4) Re-start your ADSL router.
Please follow the quick start step by step to configure the device. If
ISP provides DNS, after complete Quick Start configuration, please
go to Interface Setup Æ Internet to configure the DNS settings.
5.3 Interface Setup
Click Interface Setup
configure PPPoE/PPPoA connection settings and LAN configuration.
5.3.1 Interne t
Virtual Circuit: VPI (Virtual Path Identifier) and VCI (Virtual Channel
Identifier).
VPI – The valid range for the VPI is 0 to 255.
to set ATM VC values, setup Encapsulation,
VCI – The valid range for the VCI is 32 to 65635.
Encapsulation: Select the method of encapsulation used by your ISP
from the list. Choices vary depending on the mode selected in the
Mode field.
PPPoE/PPPoA: Enter your username, password and Encapsulation.
Then check the proper Connection Setting and IP Address which
are used to define how the router to control the Internet status.
.
50
51
5.3.2 LAN
[Router Local IP]
IP Address: Enter the IP address of your router in dotted decimal
Note: Every time you change one setting, you must click APPLY
button once, then go to next setting’s change.
52
notation, for example, 192.168.1.1 (default setting).
IP Subnet Mask: Your ADSL router will automatically calculate the
subnet mask based on the IP address that you assign. Unless subnet
mask is assigned, use the subnet mask computed by the router.
Dynamic Route: Select the Dynamic Route from RIP-1, RIP-2B and
RIP-2M.
Direction: Select the RIP direction from None, Both, In Only and
Out Only.
Multicast: IGMP (Internet Group Multicast Protocol) is a
53
session-layer protocol used to establish membership in a multicast
5.4 Advanc ed Setup
group. The router supports both IGMP-v1 and IGMP-v2. Select None
to disable it.
[DHCP
DHCP: The LAN port DHCP role – Disabled, Enabled or Relay.
IP Pool Count: This field specifies the size or count of the IP address
pool.
Size of Client IP Pool: This field specifies the size or count of the IP
address pool.
Primary DNS Ser ver: Enter the IP addresses of the DNS se rvers.
The DNS servers are passed DHCP clients along with the IP address
and the subnet mask.
Note: Every time you change one setting, you must click APPLY
]
button once, then go to next setting’s change.
5.4.1 Rou ting
This table displays the IP address of Internet destinations commonly
accessed by your network. When a computer requests to send data
to a listed destination, the device uses the Gateway IP to identify the
first Internet router it should contact to route the data most efficiently.
5.4.2 NAT
Network Address Translation (NAT) is a method for disguising the
private IP addresses used on the LAN as the public IP address used
on the Internet. It rules that specify exactly how and when to translate
between public and private IP addresses.
Virtual Circuit (VC): The virtual circuit (VC) properties of the ATM VC
interface identify a unique path that the ADSL modem router uses to
communicate via the ATM-based network with the telephone
company central office equipment.
54
55
DMZ: DeMilitarized Zone (DMZ) is cited from military phraseology.
5.5 Access Management
5.5.1 ACL
Used in network technology, saying a computer or small sub-network
that sits between a trusted internal network, such as a corporate
private LAN, and an untrusted external network, such as the public
Internet. When there is a suspected packet coming from WAN, the
router will forward this packet to the DMZ host.
Virtual Server: This feature allows Internet users to access standard
Servers on your LAN, via the router. Normally, Internet users would
not be able to access a server on your LAN because your Server
does not have a valid external IP Address.
Attempts to connect to devices on your LAN are blocked by firewall in
this device. The "Virtual Server" feature solves these problems and
allows Internet users to access to your servers.
Note: Every time you change one setting, you must click APPLY
button once, then go to next setting’s change.
Access Control Setup: This page allows you to manage the router
remotely through Web UI and Telnet Access.
IP Address: The default 0.0.0.0 allows any client to use this service
to remotely manage the router. Type an IP address to restrict access
to the client with a matching IP address.
Note: Every time you change one setting, you must click APPLY
button once, then go to next setting’s change.
56
57
5.5.2 IP Filter
5.5.3 SNMP
The IP Filter feature enables you to control the forwarding of
incoming and outgoing data between your LAN and the Internet and
within your LAN.
Telnet/FTP/TFTP/Web/SNMP: Select Telnet, FTP, TFTP, Web and
SNMP to block incoming WAN requests for the corresponding
service.
Apply: Click this button to save these settings back to the router.
The Simple Network Management Protocol (SNMP) enables a
host computer to access configuration, performance and other
system data that resides in a database on the modem. The host
computer is called a management station and the modem is called an
SNMP agent. The data that can be accessed via SNMP is stored in a
Management Information Database (MIB) on the modem.
Note: Every time you change one setting, you must click APPLY
button once, then go to next setting’s change.
Note: Every time you change one setting, you must click APPLY
button once, then go to next setting’s change.
58
59
5.5.4 UPnP
Universal Plug and Play (UPnP): You can choose “Activated” or
“Deactivated” option from this session.
Auto-Configured (by UPnP Application): Choose “Activated”
option to allow UPnP-enabled applications to automatically configure
5.5.5 DDNS
The Dynamic Domain Name System lets you use a static host name
with a dynamic IP address.
the router so that they can communicate through the router, for
example by using NAT traversal, UPnP applications automatically
reserve a NAT forwarding port in order to communicate with another
UPnP enabled device; this eliminates the need to manually configure
port forwarding for the UPnP enabled application. If you don’t want to
make configuration changes through UPnP, just choose
“Deactivated”.
Apply: Click Apply to save the setting to the router.
Note: Every time you change one setting, you must click APPLY
button once, then go to next setting’s change.
60
Dynamic DNS: Choose the option for Activated or Deactivated
DDNS.
Service Provider: The default Dynamic DNS service provider is
www.dyndns.org.
My Host Name: Type the domain name assigned to the router by
your Dynamic DNS provider.
E-mail Address: Type your e-mail address.
Username: Type your user name.
Password: Type your password of the DDNS account.
Wildcard support: Select Yes or No to turn on DYNDNS Wildcard.
Apply: Click Apply to save your changes.
61
Note: Every time you change one setting, you must click APPLY
“PC’s Clock”, or “Manually” to coordinate the time.
button once, then go to next setting’s change.
5.6 Maintenance
5.6.1 Administr ation
This field allows user to change new password.
Note: Every time you change one setting, you must click APPLY
button once, then go to next setting’s change.
Time Zone: Choose the Time Zone of your location. This will set the
time difference between your time zone and Greenwich Mean Time
(GMT).
Daylight Saving: Choose “Enabled” or “Disabled” to use daylight
savings time.
NTP Server Address: Type the IP address or domain name of your
time server. Check with your ISP/network administrator if you are
unsure of this information.
5.6.2 Time Zone
[Time Zone]
Current Date/Time: This field displays an updated Date and Time
when you reenter this menu.
[Time Synchronization]
Synchronization with: You can choose “NTP Server automatically”,
62
Note: Every time you change one setting, you must click APPLY
button once, then go to next setting’s change.
5.6.3 Firm ware
Download the firmware, save it and then extract it. The upload
process uses TFTP (Trivial File Transfer Protocol).
63
It takes a few minutes, don’t power off it during upgrading. Device will
5.6.4 Sy stem Restart
restart after the upgrade!
After a success upload, the system automatically restarts. Please wait
for the device to finish restarting (the SYS LED is on steady). This
should take about 2 minutes. You need to log in again if you want to
access the device.
Current Firmware Ver.: This filed displays the current firmware
version.
New Firmware Location: Type in the location of the file you want to
Click RESTART at the bottom of the web page if you want to make
the default setting.
Note: Every time you change one setting, you must click APPLY
button once, then go to next setting’s change.
5.6.5 Diagno stic
The Diagnostic page allows you to run a series of diagnostic tests of
your system software and hardware connections. From the Virtual
Circuit drop-down list, select the name of the Virtual Circuit on which
upload in this field or click Browse… to find it.
Upload: Click Upload to begin the upload process. This process may
take up to 2 minutes.
Note: Every time you change one setting, you must click APPLY
button once, then go to next setting’s change.
64
the diagnostics are to be shown.
65
Note: 1) User ONLY can view PVC0’s Diagnostic Test connection.
2) “Testing ADSL Synchronization” might take 30 sec to
pass the Diagnostic Test.
5.7 Status
5.7.1 Dev ice Info
The Device Info screen is a tool that you use to monitor your modem.
Note that these fields are read-only and are not meant for diagnostic
purposes. Except the Virtual Circuit, click the drop-down list and
select the name of the Virtual Circuit on which the system status is to
be shown.
66
[Device Information]
Firmware Version: This filed displays current firmware version.
MAC Address: The MAC (Media Access Control) or Ethernet
address unique to your modem.
67
[LAN]
unexpected or improper functioning and is not captured by the
IP Address: The LAN port IP address
Subnet Mask: The LAN port IP subnet mask.
DHCP Server: The status of DHCP Server (Enabled or Disabled)
[WAN]
Virtual Circuit: Click the drop-down list and select the name of the
Virtual Circuit on which the system status is to be shown.
Status: Connected or Not Connected
Connection Type: The WAN Connection Type.
IP Address: The WAN port IP address
Subnet Address: The WAN port IP subnet mask.
Default Gateway: The IP address of the default gateway, if
applicable.
DNS Server: The IP address of the DNS Server
[ADSL]
ADSL Firmware Version: This field displays current ADSL firmware
version.
Line States: This is the status of tour WAN Line.
system traps that create alarm.
You can click Save Log to display a Windows File Download dialog
box that enables opening or saving the contents of the log to your PC.
To remove all entries from the list, click Clear Log. New entries will
begin accumulating.
Modulation: The type of the modulation.
Annex Mode: The type of Annex mode.
5.7.2 Sy stem Log
The System Log displays data generated or acquired by routine
system communication with other devices, such as the results of
negotiations with the ISP's computers for DNS and gateway IP
addresses. This information does not necessarily represent
68
69
5.7.3 Statis tics
You can view performance statistics for Ethernet/ADSL router’s
number of packets transmit/receive.
If you have any trouble to configure or setup this router, please
contact us.
Before contacting us, make sure collect following information.
Submit complete detailed information of your problem will help us to
provide you accurate answer.
Model Name:
Serial Number:
PC Settings:
Other:
70
Loading...