Single Mount
Installation Instructions
www.microndisplaysolutions.com
Table of Contents
Important Safety Instructions.................................................................................................................................... 3
Configuration ............................................................................................................................................................ 4
Package Contents ...................................................................................................................................................... 5
Step 1 – Building Frame Structure ............................................................................................................................. 6
Step 2 – Determining Reference Height and Fastening ............................................................................................ 7
Step 3 – Ensuring Frame Structure is Straight and Plumb ......................................................................................... 8
Step 4 – Attaching VESA Mounting Brackets ............................................................................................................. 9
Step 5 – Mounting Monitor to Frame ..................................................................................................................... 10
Step 6 – Installing Monitor Security Lock (Optional) ............................................................................................... 11
Step 7 – Accessing behind Monitor and Servicing Monitor .................................................................................... 11
Warranty .................................................................................................................................................................. 12
Video Wall Installation Manual V155, V170, V180 Page 2
Rev. 04/2019
Important Safety Instructions
CAUTION: Before you begin any of the installation procedures read and follow the
WARNING! FAILURE TO FOLLOW INSTRUCTIONS ON ACCESSING BEHIND
WARNING! BEFORE INSTALLING THE MOUNT, ENSURE THE WALL IS
WEIGHT OF MOUNT AND MONITORS!
warnings and important safety instructions within the manual.
MONITORS AND SERVICING MONITORS MAY RESULT IN POSSIBLE PERSONAL
STRUCTUALLY SOUND AND ABLE TO PROPERLY SUPPORT THE COMBINED
Use the following safety guidelines to help protect you during the installation, especially with installing
the monitors to mount and when access to monitors is required to ensure your own personal safety.
• Read all the installation instructions before installing the mounting solution.
• Read and follow all important safety instructions.
• Depending on size of video mount solutions, two (2) or more persons may be required for
installation.
INJURY AND DAMAGE TO MONITORS DUE FROM FALLING!
• Please ensure all safety precautions are followed when working with heights.
Video Wall Installation Manual V155, V170, V180 Page 3
Rev. 04/2019
Model and Specifications
Product V155 V170 V180
Orientation
Screen Sizes
Dimensions
(WXHXD) mm
TV Weight Max
Panel VESA Mounts
Wall Mount Brackets
VESA
Security Lock
Wall Stiffer Required?
Kick Stand
Landscape or Portrait
55” to 69”
1134 x 508 x 69 1261 x 610 x 69 1541 x 762 x 69
80kg
Included (Device Used to Tilt Panels For Servicing or Access at Back)
70” to 79”
120kg
Included
Included
All VESA configurations
Included
No
80” to 100”
180kg
Colour
Listing
Aluminum with Black Side Rails
Tested and Evaluated to CSA Model Code SPE-1000, Clause 6.2.8
Video Wall Installation Manual V155, V170, V180 Page 4
Rev. 04/2019
Package Contents - Included
Model
Part KS
Description
Horizontal Rail
Side Rails
Panel VESA Bracket
(includes micro
adjustment screw)
Wall Brackets
(May already be
installed on rails)
Qty Picture
V155
V170
V180 3
V155
V170
V180
V155
V170
V180
V155 4
V170 4
V180 6
2
Part A
2
Part S
2
Part D
Part E
V155
Monitor Mounting
Hardware Kit
Kick Stand
Monitor Security
Lock
V170
V180
V155
V170
V180
V155
V170
V180
1
Part H
1
1
Part SL
Video Wall Installation Manual V155, V170, V180 Page 5
Rev. 04/2019
Step 1 – Building Frame Structure
The Side Rails have gussets already
preassembled to speed assembly.
• Loosen the square nut preinstalled on
each gusset as shown in figure 1A.
• Position the Top Rail (Part A), Bottom
Rail (Part B), Middle Rail (if supplied)
and Side Rails (Part S) as shown in
figure 1B.
• Slide the Top Rail (Part A), Bottom Rail
(Part B), and Middle Rail (if supplied) so
the square nuts are inside the top tslots of rails and they are flush with
surface of Side Rails as shown in figure
1C.
• Tighten the screws on all gussets using
6mm Hex Allen Wrench.
NOTE:
For V180 model there is a middle rail.
Fig. 1A
Fig. 1B
Fig. 1C
Video Wall Installation Manual V155, V170, V180 Page 6
Rev. 04/2019
Step 2 –Determining Reference Height and Fastening
Instructions
Diagrams
•
Determining center point for video wall.
Measure the total length of video wall
mounting frame in order to determine
center point for wall installation.
Take total length _____ / 2 to
determine center point.
• Mark wall with centre point.
• Mark wall with outside measurements
of video wall as shown in figure 2A.
• Level and fasten mount to wall.
(Fastening hardware not included)
For wood or metal studded walls only
Determine location of all wall studs that are
behind video wall and mark each stud
accordingly using stud finder.
For concrete or concrete block walls only
Depending on number of Wall Brackets
(Part E) supplied, determine placement by
evenly spacing them out
Fig. 2A
Video Wall Installation Manual V155, V170, V180 Page 7
Rev. 04/2019
Step 3 –Ensuring Frame Structure is straight and plumb
Instructions
Diagrams
IMPORTANT:
Tighten the loose
Do not push the frame structure
against the wall. The frame
structure is designed to act as the
support structure for the monitor
and not the wall itself.
a) Use a level to ensure the frame
structure is straight along the entire
length of structure. See figure 3A.
b) Loosen the preinstalled Wall Brackets
and position at stud locations.
c) In the event a portion of horizontal
section needs to be adjusted slightly
inwards or outwards the Wall Brackets
do have a slot to allow for these
adjustments. See figure 3B.
d) Once the frame structure is straight,
plum and level tighten each Bolt to
secure and lock frame the frame in
position.
Fig. 3A
Bolts at Wall
Bracket once
frame is straight
horizontally and
vertically
Fig. 3B
Video Wall Installation Manual V155, V170, V180 Page 8
Rev. 04/2019
Step 4 – Attaching VESA Mounting Brackets
Instructions
Diagrams
a) Remove monitor to be installed from
carton and attach the Panel VESA
Brackets (Part D) to back of panels at
the VESA mounts as shown in figure 4A.
Mounting hardware is provided (Part
F).
Note: If monitor orientation is portrait
mode attach Panel VESA Brackets to
back of video panels with that
orientation.
b) The mounting hardware consists of
various lengths of M6 and M8 screws to
accommodate different manufacturer
specifications.
c) If M6 screws are required, you will
need to use the white M8 sleeves by
inserting an M6 screw into the white
sleeve and then attaching Panel VESA
Bracket to back of video panel. See
figure 4B.
Fig. 4A
Fig. 4B
Video Wall Installation Manual V155, V170, V180 Page 9
Rev. 04/2019
Step 5 –Mounting Monitor
Instructions
Diagrams
IMPORTANT:
Fig. 5A
• To mount monitor, lift and slightly tilt
Before mounting any monitor
recheck to ensure all hardware has
been tighten with hex Allen keys to
prevent any physical damage to
monitor falling or personal injury.
• In previous Step 4, the Panel VESA
Brackets (Part D) should have been
attached to back of monitor at the
VESA mount locations.
monitor then insert the downward
pointing tab at top of each Panel VESA
Bracket into the top t-slot of rail. See
figures 5B and 5C.
• Make sure both Panel VESA Brackets
are inserted properly otherwise
monitor may fall. See figure 5D.
• Once monitor is mounted to rail it can
be moved sideways to centre on mount
by simply along the rail.
Fig. 5B Fig. 5C
Fig. 5D
Video Wall Installation Manual V155, V170, V180 Page 10
Rev. 04/2019
Step 6 – Installing Monitor Security Lock (Optional)
Instructions
Diagrams
The Monitor Security Locks (optional item)
Instructions
Diagrams
a) To gain access behind monitor you will
Fig. 7A
are only fastened to top of Panel VESA
Brackets.
• Place a Monitor Security Lock on either
the left and right Panel VESA Bracket as
shown in figure 6A.
• Once the Monitor Security Lock has
been positioned directly on top of
Panel VESA Bracket, secure the lock by
tightening the two (2) screws. See
Figure 6B.
Fig. 6A
Fig. 6B
Step 7 – Accessing behind Monitor and Servicing Monitor
require the use of Kick Stand (Part KS)
provided. To insert Kick Stand simply
tilt bottom of monitor and ensure
locking tab is inserted into top slot of
bottom rail as shown in figure 7A.
Video Wall Installation Manual V155, V170, V180 Page 11
Rev. 04/2019
Warranty
Micron Display Solutions (“MICRON”) warrants to the first purchaser for this product (“Product”),
when shipped in its original container and sold or distributed in Canada by Micron or by an authorized
Micron dealer, and Product was not sold “as is” or “sales final” that the Product will be free from
defects in material and workmanship for a period of three (3) years and will within the warranty
period, either repair the defective Product or provide the purchaser a replacement of the defective
Product.
This warranty does not apply to any appearance items of the product nor to the exterior of which has
been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal
service or handling, which has been altered or modified in design or construction, or if the serial
number or model number affixed to Product has been removed, defaced, changed, altered or
tampered with.
Micron Display Solutions
2679 Bristol Circle, Unit 6
Oakville, Ontario
L6H 6Z8
(905)-828-1662
www.microndisplaysolutions.com
Video Wall Installation Manual V155, V170, V180 Page 12
Rev. 04/2019
Loading...