This Micro Motion product complies with all applicable European directives when properly installed in accordance with the
instructions in this manual. Refer to the EU declaration of conformity for directives that apply to this product. The EU declaration
of conformity, with all applicable European directives, and the complete ATEX Installation Drawings and Instructions are available
on the internet at www.emerson.com or through your local Micro Motion support center.
Information affixed to equipment that complies with the Pressure Equipment Directive, can be found on the internet at
www.emerson.com.
For hazardous installations in Europe, refer to standard EN 60079-14 if national standards do not apply.
Other information
Full product specifications can be found in the product data sheet. Troubleshooting information can be found in the configuration
manual. Product data sheets and manuals are available from the Micro Motion web site at www.emerson.com.
Return policy
Follow Micro Motion procedures when returning equipment. These procedures ensure legal compliance with government
transportation agencies and help provide a safe working environment for Micro Motion employees. Micro Motion will not accept
your returned equipment if you fail to follow Micro Motion procedures.
Return procedures and forms are available on our web support site at www.emerson.com, or by phoning the Micro Motion
Customer Service department.
Emerson Flow customer service
Email:
• Worldwide: flow.support@emerson.com
• Asia-Pacific: APflow.support@emerson.com
Telephone:
North and South America
United States800-522-6277U.K.0870 240 1978Australia800 158 727
Chapter 1Smart Meter Verification................................................................................................5
Chapter 2Execute an SMV test from the Modbus host....................................................................7
Chapter 3Configure and view scheduled test executions............................................................... 9
Chapter 4Read stored test results................................................................................................11
Operation and Use Guideiii
ContentsOperation and Use Guide
October 2019MMI-20017073
ivMicro Motion Modbus Interface Tool for SMV
Operation and Use GuideSmart Meter Verification
MMI-20017073October 2019
1Smart Meter Verification
Smart Meter Verification (SMV) is a Micro Motion diagnostic tool that allows you to
compare the sensor’s current performance to benchmark data established at the factory.
Using the Modbus interface, you can:
• Execute an SMV test from the Modbus host
• Set up a scheduled test execution
• Read result data for the twenty test results stored on the transmitter
Note
You can view more than twenty previous test results and see detailed test reports only
if SMV is licensed.
For more information on requirements and features, see your transmitter configuration
and use manual.
Operation and Use Guide5
Smart Meter VerificationOperation and Use Guide
October 2019MMI-20017073
6Micro Motion Modbus Interface Tool for SMV
Operation and Use GuideExecute an SMV test from the Modbus host
MMI-20017073October 2019
2Execute an SMV test from the
Modbus host
Prerequisites
The Modbus host must be connected to the transmitter.
Procedure
1. If you are fixing outputs during the test, set the output state from Register 3093.
OptionDescription
0Last Measured Value
1Fault Action
2. From Register 3000, start or abort the test.
0 = Abort
1 = Start with outputs fixed (apply Register 3093)
6 = Start in Continue Measurement Mode
3. Read Register 3001. Is the test running?
Option
> 0 = YesRead the percent complete from Register 3020.
0 = NoContinue to the next step.
4. Read Register 3003. Did the test run to completion?
Option
16 = YesContinue to the next step.
< 16 = NoRead the abort code on Register 3002.
Description
Range: 0 to 100
Description
1 = User Initiated Abort
3 = Frequency Drift
5 = High Drive Gain
8 = Unstable Flow
12 = Fault Condition
13 = No Air Reference
14 = No Water Reference
15 = Missing Configuration Data
Operation and Use Guide7
Execute an SMV test from the Modbus hostOperation and Use Guide
October 2019MMI-20017073
5. Read Register 3004. Is the test passed?
0 = YesThe test passed.
> 0 = NoThe test result is caution. Continue to the next step.
6. For Model 5700 transmitters, read Register 6348. For all other transmitters, read
Register 6364.
128Possible coating or corrosion/erosion; coating detection is available only on
the Model 5700
256Possible extreme temperature or corrosion
512Possible extreme temperature or damage
1024Possible coating or damage; coating detection is available only on the Model
5700
2048Possible corrosion/erosion
4096Possible coating; coating detection is available only on the Model 5700
8Micro Motion Modbus Interface Tool for SMV
Operation and Use GuideConfigure and view scheduled test executions
MMI-20017073October 2019
3Configure and view scheduled test
executions
Use the Modbus host to set up the schedule.
Prerequisites
To configure a test execution and view a scheduled test execution, the Modbus host must
be connected to the transmitter. Once the schedule is loaded into the transmitter, the
Modbus host no longer has to be connected to the transmitter.
Procedure
1. Choose any of the following options:
OptionDescription
Specify the hours until test
execution for a single
execution
Specify the hours for a
recurring execution
View the number of hours
until the next execution
Cancel a scheduled
execution
2. Disconnect as desired.
Write a floating-point value to Register 2993.
• To specify the number of hours until the first
test is executed, write a floating-point value to
Register 2993.
• To specify the number of hours between test
executions, write a floating-point value to
Register 2995.
Read Register 2997.
• Write 0 to Register 2993.
• Write 0 to Register 2995.
Operation and Use Guide9
Configure and view scheduled test executionsOperation and Use Guide
October 2019MMI-20017073
10Micro Motion Modbus Interface Tool for SMV
Operation and Use GuideRead stored test results
MMI-20017073October 2019
4Read stored test results
The results of the twenty most recent tests are stored on the transmitter.
Note
You can view more than twenty previous test results and see detailed test reports only if
SMV is licensed.
Prerequisites
To read test results, the Modbus host must be connected to the transmitter.
Procedure
1. Specify the test record you want to read by writing a value between 0 and 19 to the
appropriate register.
Register for Model
5700 transmitters
57792984For Model 5700 transmitters:
Register for all other
transmitters
Description
Register 5825 = the most recent test
For all other meters:
0 = the most recent test
2. Read the Modbus register values using the descriptions in the following table.
Registers for Model
5700 transmitters
56972985Test number
5820 and 58212986 Bit #7Test result
58192986 Bits #6–4State
58182986 Bits #3–0Abort code (compressed)
57802987Time initiated
5782 and 57832989Inlet normalized data
5784 and 57852991Outlet normalized data
Registers for all other
transmitters
Description
0 = Pass
1 = Caution
3. Disconnect as desired.
Operation and Use Guide11
*MMI-20017073*
MMI-20017073
Rev. AD
2019
Micro Motion Inc. USA
Worldwide Headquarters
7070 Winchester Circle
Boulder, Colorado USA 80301
T +1 303-527-5200
T +1 800-522-6277
F +1 303-530-8459
www.emerson.com
Micro Motion Asia
Emerson Automation Solutions
1 Pandan Crescent
Singapore 128461
Republic of Singapore
T +65 6363-7766
F +65 6770-8003
The Emerson logo is a trademark and service mark of Emerson Electric Co. Micro Motion, ELITE,
ProLink, MVD and MVD Direct Connect marks are marks of one of the Emerson Automation
Solutions family of companies. All other marks are property of their respective owners.
Micro Motion Europe
Emerson Automation Solutions
Neonstraat 1
6718 WX Ede
The Netherlands
T +31 (0) 318 495 555
T +31 (0) 70 413 6666
F +31 (0) 318 495 556
www.emerson.com/nl-nl
Micro Motion United Kingdom
Emerson Automation Solutions
Emerson Process Management Limited
Horsfield Way
Bredbury Industrial Estate
Stockport SK6 2SU U.K.
T +44 0870 240 1978
F +44 0800 966 181
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.