Micrometl FLRK-I235-TD, FLRK-I213-TD Installation Manual

MicroMetl

1” - 2” Filter Rack

Model:

FLRK-I213-TD..............

FLRK-I235-TD..............

WARNING: HAZARDOUS VOLTAGE - DISCONNECT POWER BEFORE SERVICING

!

ALL phases of this installation must comply with NATIONAL, STATE, AND LOCAL CODES

IMPORTANT - This document is customer property and is to remain with this unit. Please return to service information pack upon

completion of work.

NOTE: This lter rack is required when installing an
economizer or any outside air damper and recommends the
use of the ACDR-I213-TD/ACDR-I235-TD Filter Access Door.

NOTE: To change lter rack from 1” to 2” lters:

• Remove 2 screws that secure the 1” lter angle to the
Upper Filter Channel and discard angle.

• Remove 2 screws that secure the 1” lter angle to the
Lower Filter Channel and discard angle.

Used with:

2/4 YC*,WC*,TC*,DC** 018-036A
2/4 YC*,WC*,TC*,DC** 042-060A

Right Blank-Off
Plate Screw

Filter Rack Installation

1. Open or remove the Filter Access Door. See Figure 1.

2. UPPER FILTER CHANNEL:

a. Remove the screw from the top of the right coil blank-
off plate just inside the Coil Access opening, see Figure 1.

b. Hook the left side of the upper lter bracket into the tab
projecting from the rear/left end of the indoor coil ashing.
c. Install the right side of the upper lter bracket, aligning
the slots of the lter frame to the right coil tube sheet

engagement holes (where the screw was removed in Step
a.). See Figure 3.

Figure 1. Filter Access Door

3. LOWER FILTER CHANNEL:

Slide the lower lter channel across the drain pan and

place the channel bracket lip over the drain pan.

4. Install the appropriate lter(s) and ll plate. Close the
Filter Access Door or panel. See Table 1 for appropriate

lter sizes.

NOTE: For unit horizontal applications, Return Air Panel is to
remain attached to the unit base pan return opening. Bottom
lter rack channel will sit on top of Return Air Panel perimeter
ange.

WARNING

! !

HAZARDOUS PRESSURES!

Coils contain refrigerant under pressure. When attaching lter
channel assemblies and lter retainer angle to coil blank-off

plate use ONLY the holes from which you removed the screws.
Failure to follow these safety precautions could result in coil
bursting, which could result in death or serious injury.

Form No. 4455-2P

Filter
Location

A Fill Plate is Furnished in

the FLRK-I213-TD Kit.

Figure 2. Right Side Fill Plate

CAUTION

SHAPE EDGE HAZARD!

Be careful of sharp edges on equipment or any cuts made on
sheetmetal while installing or servicing. Personal injury may
result.

Upper Filter Channel

Rear Slot Insert Over
Tab on Unit Barrier

Lower Filter Channel

Figure 3. Filter Rack Components

Fill Plate
(Used on 018-036 Models Only)

042-060 models shown

AIRFLOW AIRFLOW

Two-Inch

One-Inch

VIEW A

Blank-off Removed

Figure 4. View of Upper Filter Rack Left Side Mounting

Unit Size Filter Size

018-036 Models Use one 18” x 25” lter (one or two inch)

042-060 Models Use two 18” x 20” lters (one or two inch)*

Indoor Coil

Installed
Filter Rack

A

Table 1 - Filter Rack Filter Sizes

*Note: If not using ACDR-I213-TD/ACDR-I235-TD Filter Access
Door, use one 18” x 20” and one 18” x 18” lter. (One or two inch)

Form No. 4455-2P