Micromega CD, CD-SE, CD132-SE User Manual

CD – CD-SE – CD132-SE

USER’S MANUAL

* non contractual pictures

- 2 -

Dear Customer,
Thank you for purchasing one of the 3 Micromega CD players: CD, CD-SE, CD132-SE. These players are mainly different by their audio characteristics. This manual is then
common for the 3 models.
This unit provides ease of use and sonics of the highest quality. Please pay close attention to this instruction manual, and read it fully before attempting to operate. It is designed
to ensure you maximise your pleasure of CD player and familiarise you with its many unique functions.

CHECKING

Check that the carton has no damage. Should you have any doubt about its condition,
please do not hesitate to contact your dealer.

UNPACKING

Very carefully remove the unit from the box, taking care to preserve all the packing
material. It is good practice to put the carton and its contents into an outer plastic bag
and deposit it somewhere safe and dry. In the unlikely event that your unit needs to be
sent back to either your dealer or distributor, it must be sent in the original packing
material. Failure to observe this will invalidate your warranty.

ACCESSORIES

Upon opening the carton you should find the following:

• Mains Lead.

• Stereo Cinch cable

MAINS VOLTAGE

Check that the mains voltage indicated on both the carton and the bottom of the unit
correspond to the local power supply.
If you are in any doubt, consult your dealer.

INSTALLATION

In order to obtain the maximum performance of CD player, it is important to follow the
installation instructions.
Wherever possible, we recommend that the CD player is installed in an audio rack or
other suitable furniture that provides sufficient ventilation.

CONNECTIONS

Having verified that the ON/OFF switch is on OFF position, connect the mains leads
provided to the rear of the unit and to the wall socket.
Connect the interconnect cable from the rear of your player to your amplifier input.
Connect the Digital out if required.

POWER UP

You may now turn on your CD player by switching the ON/OFF switch located at the
back of the unit. A message “CD” is written for a second.

At first start-up, or when both keys NEXT and PREV are pressed simultaneously and
when power is switched on, you can choose the displaying language of your player:

Press PLAY to select French or DOBM to select English. There is 5 seconds to do so, if
not English language is selected by default. Then a welcoming message appears.

The standby LED lightens up indicating that the unit is in standby mode.
Press once the CD key of the remote control or the STANDBY key of the unit.

If there is a disc, reading starts and its content is displayed.
Otherwise it indicates:

FRONT PANEL

STANDBY: To switch the unit in and out of Standby mode. A red LED located in the

middle of the panel illuminates when in Standby mode.

DOBM: Digital output on/off.
NEXT: Selection of the next track and forward search during play.
PREV: Selection of the previous track and reverse search during play .To replay the

current track during play.
PLAY/PAUSE: To start play and to pause during play, absolute phase inversion (long

pressure).

STOP/OPEN: To stop play, to clear a program in stop. Display on/off (long pressure).

DISPLAY

The display indicates:

• On the left side track indication.

• In the middle the status of the unit

• On the right side the time in minutes and seconds.

PLAY

Open the tray and place a disc. Be careful to place correctly the puck at the centre.
When the cover is closed, the player reads the disc:

And it displays its contents:

If no disc is detected, the display indicates "NO DISC".
Press PLAY to begin reading the disc. The display indicates:

:

The display indicates on the left hand the current track, play mode and elapsed time on
the right hand.
If you wish to stop playing a disc, press STOP on the unit or with the remote or open the
cover.

STANDBY MODE

To put the player in standby mode again, press STANDBY on the unit or the remote.
If the tray is open, it s closed then the LED illuminates showing the device is in standby
mode.