Micro Matic BC-1206-2 Installation Manual

Page 1
2 Faucet Kegerator Kit
Assembly Instructions
For Models:
BC-1206-2 • BC-1206S-2 • SBC490BI-2 • SBC490BIFR-2 • SBC490BISSTB-2
www.micromatic.com 1-866-291-5756
2 Faucet Kegerator Kit - Assembly Instructions
1
Page 2
Kit Includes:
2 – 4' Length
5/16" I.D. Gas Hose
1 – 1' Length
5/16" I.D. Gas Hose
6 – Plastic
Snap Clamp
1 – Plastic T for
5/16" I.D. Gas Hose
1 – Single Gauge
CO2 Regulator
1 – 2 Faucet
Beer Tower
1 – Tower
Gasket
1 – Worm
Gear Clamp
2 – American
D System Keg Coupler
Please follow the included manufacturer instructions with the following modications:
1
From Top of Kegerator: Slide tower
gasket over the hex nuts and beer hose up to the base of tower. Drop one (1) beer hose through hole in top of kegerator.
Take second beer hose, cut approximately ½" above hex nut. Remove and discard clamp. Save the hex nut and tailpiece they will be re-used in the next step. Drop second beer hose through hole in kegerator top, alongside rst beer hose.
2
From Inside Kegerator: Insert the tailpiece
into the hex nut, slip the black washer into the base of threaded hex nut. Screw the hex nut onto one of the couplers.
Grab the cut beer hose end, slide on screw clamp and the tailpiece into the beer hose. With the beer hose over the tailpiece, secure screw clamp.
2
3
Mounting Tower: The provided 3"
diameter tower does not line up with the factory provided pilot holes on top of kegerator. Center tower and gasket over hole in kegerator and mark mounting
2 Faucet Kegerator Kit - Assembly Instructions
holes. Drill four (4) 1/8" diameter pilot holes approximately 3/4" deep. Using the 1” wood screws provided, secure tower to kegerator top.
www.micromatic.com
Page 3
4
clamp on the end of the one (1) foot length of 5/16" I.D. CO2 gas hose, slide end of hose onto regulator outlet/shut-o valve. Take plastic T-tting and insert into the other end of gas hose with T-tting facing down.
Ready to tap kegs.
5
Slide a clamp on each end of the two four (4) foot lengths CO2 hose. Insert one end of each four (4) foot hose on to the T-tting and then insert the free end on to the gas inlet side of the couplers.
BC-1206-2 (Model Shown)
Tighten all clamps.CO2 (Gas) Line Assembly Place one (1)
www.micromatic.com 1-866-291-5756
2 Faucet Kegerator Kit - Assembly Instructions
3
Page 4
Visit www.micromatic.com
Information & Resources For All Your Draft Dispensing Needs
FAQ’s
Answers to many commonly asked questions and troubleshooting solutions are presented.
Beer Forum
Discuss a wide range of beer dispensing topics in a vibrant online “beer community” where members commercial and private, technical and non-technical nd a relaxed platform.
Participation in the Forum is free! Reading the Forum does not require registration. The Forum is moderated by many of Micro Matic’s Dispense Institute instructors and knowledgeable sta. Our expert moderators have years of draft system installation experience and look forward to sharing their experience and responding to posted questions. Share an experience, ask a question, and then check back often!
Complete Line Of Draft Beer Equipment!
5047 5050
7509E
Tap Handles
Rock On with a guitar! Surf’s Up with a beach babe or a surfboard. Frogs, dolphins, and bears Oh My! Enjoy a cold one with man’s best friend.
Party Pump
The Micro Matic party pump will out perform and outlast any similar party pump that is on the market!
CFP-1
Line Cleaner
Always clean the beer
line and equipment before
connecting a fresh keg.
00866-D0710 Copyright © 2010 by Micro Matic USA, Inc. All Rights Reserved.
4
2 Faucet Kegerator Kit - Assembly Instructions
www.micromatic.com
Loading...