Page 1
MX86 QR Code Scanner User Manual
July 5, 2017
Beijing Microlight Internet Technology Co., Ltd.
Page 2
Disclaimer
Before using the product, please read carefully all the contents of
Do not disassemble the product or tear off the seal on the product.
Otherwise, Beijing Microlight Internet Technology Co. Ltd. will not be
responsible for the warranty or replacement of the product.
The pictures in this manual are for reference only. If there is a
discrepancy between an individual picture and the actual product, the
actual product shall prevail. For the upgrade of this product, Beijing
Microlight Internet Technology Co., Ltd. reserves the right to modify
the document at any time without notice.
The use of this product is at your own risk. To the fullest extent
permitted by applicable law, damages and risks resulting from the use or
inability to use the software, including but not limited to direct or
indirect personal damages, loss of commercial profits, trade interruption,
loss of business information or any other economic loss, Beijing
Microlight Internet Technology Co. Ltd. does not assume any
responsibility.
All rights of interpretation and modification of this manual belong
to Beijing Microlight Internet Technology Co, Ltd.
www.vguang.cn
2
this MX86 Product User Manual (hereinafter referred to as “Manual”)
to ensure the safe and effective use of the product.
Page 3
Table of Contents
Disclaimer
..................................................................................................................................
2
Copyright Notice........................................................................................................................6
Preface....................................................................................................................................... 7
Product Introduction
.............................................................................................................
7
Product Features
...................................................................................................................
7
Strong reading ability
...............................................................................................
7
Paper code reading ability
........................................................................................
7
High speed reading
...................................................................................................
8
Easy to use
................................................................................................................
8
Precautions............................................................................................................................8
Chapter Ⅰ Product Parameters
...............................................................................................
9
Appearance parameters
........................................................................................................9
Reading parameters
............................................................................................................ 10
Electrical parameters...........................................................................................................11
Interface parameters
...........................................................................................................
12
USB interface
..........................................................................................................
12
RS232 interface
.......................................................................................................
13
www.vguang.cn
3
Page 4
RS485interface........................................................................................................13
TTL interface........................................................................................................... 14
Wiegand Interface
..................................................................................................
14
WIFI Interface
......................................................................................................... 14
Ethernet Interface
...................................................................................................
15
Chapter Ⅱ Wiring instructions
...............................................................................................
16
Pin definitions
......................................................................................................................
16
USB/WIFI/Ethernet Wiring
..................................................................................................18
RS232 WiringRS232 connection
..........................................................................................
19
Wiegand/TTL/RS485/WIFI Wiring.......................................................................................21
Chapter III Product Configuration
..........................................................................................
22
Run Configuration Tool
....................................................................................................... 22
Configure Corresponding Functions....................................................................................22
Chapter Ⅳ Common Faults and Troubleshooting Methods...............................................27
Contact Information
................................................................................................................28
Version Information
................................................................................................................29
www.vguang.cn
4
Page 5
Copyright Notice
All information contained in this manual is protected by copyright, and Beijing
Microlight Internet Technology Co., Ltd. reserves all rights. Without the written
permission of our company, any unit or individual shall bear legal liability for
taking any form of excerpt, coping any or all of the contents of this document or
selling or using the product bundled with other products in any way or for any
reason.
www.vguang.cn
6
Page 6
Preface
Product Introduction
Thanks for using the MX86 series of scanners provided by Microlight Internet Ltd. This product can
realize QR code identification and RF card reading. Please read the user manual carefully before use, you will
appreciate its perfect function and simple operation method.
This product is mainly used for QR code identification and RF card reading. The company does not
assume responsibility for the property loss or personal injury caused by the user’s abnormal operation. Please
design and develop the corresponding product according to the technical specifications and reference in the
manual. Also please pay attention to the general safety matters that should be taken into account when using
mobile products.
Before the statement, the company has the right to modify the contents of this manual according to the
needs of technological development.
Product Features
S t r o n g r e a d i n g a b i l i t y
It can recognize the QR code and one-dimensional code on the screen of the mobile phone, support the
enhanced engine mode, and can scan and read the code when the screen of the mobile phone is dark.
P a p e r c o d e r e a d i n g a b i l i t y
The main QR codes and various one-dimensional codes printed on the paper can also be read.
www.vguang.cn
7
Page 7
H i g h s p e e d r e a d i n g
Different mobile phone LCD screens generally have different contrast, color, and degree of reflection,
which can be read as long as the code system is within the reading window.
E a s y t o u s e
Scanners can be configured using configuration tools to achieve optimal operation.
Precautions
Dismantling and modification: Please do not disassemble or modify the hardware of the product. If the
equipment is damaged thereof, the company will not be responsible for the warranty.
Abnormal condition: Keep away from fire. If you find unusual odor, overheat or smoke, please immediately
turn off the power switch and unplug the plug from the AC outlet, and contact the dealer where you
purchased the product or our customer service center.
Drop damage: If the product is damaged due to falling on the ground, please immediately turn off the power
and contact the dealer where you purchased the product or our customer service center.
Placement location: Please do not place the product in an unstable or uneven place, so as to avoid the device
falling down and causing damage; please do not put the device in a place with large amount of moisture or
dust, so as to avoid causing electric leakage or fire.
Please keep the illuminating glass lens clean. When wiping, use soft cotton or lens paper. Do not wipe the
window glass with detergent or dissolved liquid.
Do not touch the window glass with abrasive substances, so as to avoid wearing the window glass and
affecting the reading effect.
www.vguang.cn
8
Page 8
Chapter Ⅰ Product Parameters
Apparent parameters
Figure 1-1 Vertical Vie
www.vguang.cn
9
Page 9
Figure 1-2 Side View
Reading Parameters
Reading Parameters of MX86 series QR
code
QR code: QR Code, Data Matrix, PDF417, etc.
Identification code
One-dimensional code：EAN-8,EAN-13,ISBN-10,ISBN-13
,
UPC-E,UPCA,CODE39,CODE93.CODE128 etc;
Decoding support
All prints such as mobile phones, screens, and paper
Reading depth of field
0mm-100mm
Reading accuracy
≥5mil
Reading rate
15 /s
Reading speed
100ms each time (average), supports continuous reading
Reading direction
360 degrees
Table 1-1 QR code reading parameters
www.vguang.cn
10
Page 10
Reading parameters of MX86 series NFC
Identification card
type
Mifare_UltraLight、Mifare_One(S50)
、
Mifare_One(S70)、Mifare_Pro(X)、Mifare_DESFire
RF operating
frequency
13.56MHZ
Effective operating
distance
<5cm
Reading rate
15 /s
Table 1-2 NFC reading parameters
Note: The RF antenna is related to the environment. If there is metal around the product, the quality of
swiping card will be affected.
Electrical parameters
MX86 Series Device Parameters
USB (HID Analog Keyboard, Custom HID), RS485, RS232,
Support interface
TTL,WIFI, Wiegand, Ethernet
LED diffuse illumination: white light (adjustable brightness), red
Light source
light green light status light (configurable on), blue indicator light
Image sensor
300,000 pixel CMOS sensor
Maximum
resolution
640*480
Indicator
Buzzer, LED indicator
Operating
temperature
-20~70 ℃
Storage
temperature
-40 to 80
℃
Table 1-3 Device parameters
www.vguang.cn
11
Page 11
MX86 Series Device Parameters
Humidity
Relative humidity 5%~95% (non-condensing, non-waterproof)
Ambient light
0〜100000LUX
Data cable
6pin cable, USB cable, DB9 cable
Power supply
VCC=4.7V~15V or VUSB=4.8~5.5V
5V input voltage, USB output
5V input voltage, WIFI
mode
output mode
Working current
150mA (average) 190mA
230mA (average) 330mA
(instantaneous maximum)
(maximum instantaneous)
Materials
Top cover bottom cover: imported PC Body: imported PC
Recognition Window: tempered glass
OS
Windows (xp.7.8.10), Linux, Android, Mac, etc.
Tab le 1 -3 Dev ic e P ara me te rs Con ti nu ed
I n t e r f a c e p a r a m e t e r s
USB Parameters
MX86 series USB interface parameters
Wiring type
USB Type-A to 5PIN 2.0mm terminal
Support interface
USB2.0 backward compatible, slave device
Theoretical
bandwidth
480Mbit/s high-speed interface
Interface voltage
5V
Protection
standard
IEC 61000−4−2 Level 4 ESD Protection
Table 1-4 USB Interface Parameters
www.vguang.cn
12
Page 12
RS232 in terface
MX86 series RS232 interface parameters
Wiring type
DB9 to 6PIN 2.0mm terminal
Support interface
point-to-point
Baud rate
300 bps to 460800bps, default 115200bps
Interface voltage
±6V
±15kV Human Body Mode
Protection standard
±15kV IEC61000-4-2 Air Discharge Mode
±8kV IEC61000-4-2 Contact Discharge Mode
Table 1-5 RS232 Interface Parameters
RS485 in terface
MX86 series RS485 interface parameters
Wiring type
6PIN 2.0mm to 6PIN 2.0mm terminal
Support
interface
Point-to-point or multi-machine communication
Baud rate
300 bps to 460800bps, default 115200bps
Interface
voltage
0-3.3V
±18 kV HBM protection
Protection
standard
±13 kV IEC61000-4-2 Contact Discharge
+4 kV IEC61000-4-4 Fast Transient Burst
Table 1-6 RS485 interface parameters
www.vguang.cn
13
Page 13
TTL interface
MX86 series TTL interface
parameters
Wiring type
6PIN 2.0mm to 6PIN 2.0mm terminal
Support interface
TTL COMS
Baud rate
300 bps to 460800bps, default 115200bps
Interface voltage
3.3V
Table 1-7 TTL interface parameters
Wiegand Interface
MX86 series Wiegand interface
parameters
Wiring type
6PIN 2.0mm to 6PIN 2.0mm terminal
Support interface
Wiegand 26, Wiegand 34
Interface voltage
4.3V
Protection
standard
±15 kV HBM protection
Tab le 1 -8 Wie ga nd int er fa ce par am et er s
WIFI Int erface
MX86 series WIFI interface parameters
Wiring type
6PIN 2.0mm to 6PIN 2.0mm terminal USB
Type-A to 5PIN 2.0mm terminal
Support interface
TCP/HTTP
Theoretical
bandwidth
40Mbps
OPEN interface
3.3V (default high level at startup)
Table 1-9 WIFI interface parameters
www.vguang.cn
14
Page 14
Ethernet Interf ac e
MX86 series Ethernet interface
parameters
Wiring type
USB Type-A to 5PIN 2.0mm terminal
Support interface
RJ45
Theoretical
bandwidth
10/100Mbps adaptive Ethernet interface
Protection standard
1.5KV electromagnetic isolation
Network protocol
TCP
Cache
Send: 6K bytes, Receive: 4K bytes
Connection
characteristics
Cross direct connection automatic conversion
Table 1-10 Ethernet interface parameters
www.vguang.cn
15
Page 15
Chapter
Ⅱ
Wiring instructions
Pin definition
MX86 outputs 5pin interfaces:
Figure 2-1 5pin socket
PIN#
Signal Name
I/O
Description
1
GND_EARTH
-
Shield ground, connect to USB shield
2
GND
-
Power ground
3
DATA+
-
Data+
4
DATA-
-
Data-
5
VUSB
Output
USB power supply
Table 2-1 5pin socket wire sequence
www.vguang.cn
16
Page 16
MX86 external output 6Pin interfaces:
Figure 2-2 6pin socket
PIN#
Signal Name
I/O
Description
RX
INPUT
Serial logic level input
1
DATA0
OUTPUT
Wiegand data 0
OPEN
OUTPUT
Access control output
TX
OUTPUT
Serial logic level output
2
DATA1
OUTPUT
Wiegand data 1
3
GND
-
Power ground
4
VCC
-
Power input
5
RS485-A
IO
RS485 Level Driver IO
6
RS485-B
IO
RS485 Level Driver IO
Table 2-2 6pin socket wire sequence
www.vguang.cn
17
Page 17
USB/WIFI/Ethernet Wiring
Fig ur e 2- 3 US B i nt er fac e c abl e
Figure 2-4 2.0mm 5Pin plug
USB-A
123
Shielded
wire
5Pin plug
4
1
GND
2
GND
3
DATA+
4
DATA-
5
VUSB
Table 2-3 USB interface cables sequence
www.vguang.cn
18
Page 18
RS232 wiring
Figure 2-5 RS232 interface cable
Figure 2-6 2.0mm 6Pin plug
www.vguang.cn
19
Page 19
DB9
12345
678
9
2.0mm
interface
1
Empty pin
2
Empty pin
3
GND
4
VCC
5
232-TX
6
232-TX
Table 2-4 RS232 interface cables sequence
www.vguang.cn
20
Page 20
Wiegand/TTL/RS485/WIFI Wiring
Figure 2-7 Wiegand/TTL/RS485/WIFI cable
Figure 2-8 2.0mm 6Pin plug
Pin No.
Color
Signal description
Pin No.
Color
Signal description
1
Purple
RX/ DATA0/OPEN
4
Red
VCC
2
Yellow
TX/ DATA1
5
Brown
RS485-A
3
Black
GND
6
Blue
RS485-B
www.vguang.cn
21
Table 2-5 Wiegand/TTL/RS485/WIFI interface cables sequence
Page 21
Chapter III Product Configuration
Run Configuration Tool
（1） Run configuration tool: Double-click the MX86 configuration tool application.
Figure 3-1 Configuration tool icon
Figure 3-2 Configuration tool interface
Configure Corresponding Functions
www.vguang.cn
22
（2）
successful＂appears.
(1)Working Mode: Can be configured as normal mode or development mode, under normal mode, Adjustable to
USB, TTL, Serial port, WiFi four output methods.
Device Connection: Click the [Connect Device] button and the message＂Device connection
Page 22
Figure 3-3 Normal mode
(2) General configuration:
www.vguang.cn
23
Under development mode, can be configured as USB, serial protocol, communication protocols methods etc.
choose according to your needs.
Figure 3-4 Development mode
Figure 3-5 General configuration options
Page 23
Code selection: Changing the code system is available, the QR code (QR code) is checked by default. The
rest of the code system can be selected according to your needs.
Output settings: Scan code prefix and suffix can be set;
Decoding Engine: Choosing to QR strengthens or bar code strengthens , choose according to your needs.
Control settings: You can set the end of the scan code information with a line break or carriage return, you
Scan code mode: It can be adjusted to single mode or interval mode. The same two-dimensional code will not
Scanning behavior: the scanning feedback can be configured as buzzer, turn off the light, and flash red light.
Device number and brightness adjustment: You can configure the device number and adjust the brightness of
(3) NFC Options:
NFC switch: Control whether to turn on the NFC function, check it and turn it on;
Output start bit and output length: You can set the length of the output start bit and output data when reading
NFC prefix-suffix settings: You can set the card prefix and suffix to char or hex, you can also set the content
Post-swipe card reaction: Can set the post-swipe card feedback as buzzer, lights off, flashing red or green
Swipe card output format settings: Can be configured for direct output, data transfer to hexadecimal output or
Swipe card output forward and reverse settings: You can set the normal and reverse order of regular card and
www.vguang.cn
24
can also control the lighting switch;
be recognized continuously under single mode. The scan interval time can be set under interval mode. The
default is 300 milliseconds.
You can also configure the buzzer delay and the flash delay time;
the light;
the card.
of the prefix and suffix;
light;
data to decimal output;
ID card.
Figure 3-6 NFC configuration
Page 24
(4) WIFI Options:
Figure 3-7 WIFI configuration
Wi-Fi output mode: Can be configured into four output methods, namely TCP, HTTP, TCP protocol and
Network transmission behavior: You can configure the feedback of transmission success and failure after
Wifi connection setting: You can configure the connected wifi name and wifi password;
Heartbeat settings: Heartbeat packet function can be set, heartbeat packets only work in TCP environment;
Network Configuration: Configure the server's address, port number, and timeout period.
(5) Ethernet Options:
www.vguang.cn
25
HTTP protocol, in the protocol mode, the data transmission format will be in accordance with the Microlight
wifi transmission protocol;
scanning the code;
Page 25
Figure 3-8 Ethernet configuration
Wired output mode: Can be configured into four output methods, namely TCP, HTTP, TCP protocol and
Network transmission behavior: You can configure the feedback of transmission success and failure after
IP mode setting: Static IP or dynamic IP mode can be configured. Static IP only takes effect on versions
Heartbeat settings: heartbeat packets can be set, heartbeat packets only work in the TCP environment;
Network Configuration: Configure the server's address, port number, and timeout period.
www.vguang.cn
26
HTTP protocol, in the protocol mode, the data transmission format will be in accordance with the Microlight
wifi transmission protocol;
scanning the code;
earlier than 1.3.4.
Page 26
Chapter Ⅳ Common Faults and Troubleshooting Methods
After the Wiegand output is configured, the scan code has no output.
When at Wiegand 34 output, the scanner’s QR code output only supports 6-10 characters output, so if the QR
After adjusting to the secondary development mode, the product cannot connect to
the configuration tool.
Failed to output when scanning IDs
www.vguang.cn
27
code information is less than 6 bits, complement 0 to the front bit to get 6 bits to generate output.
In addition, the Wiegand output only supports pure digital output. Please check whether the scanned QR code/ID
card content conforms to the specification.
If you adjust the work mode from normal mode to secondary development mode that the secondary development
output mode does not match the output mode in the normal configuration, the configuration tool cannot be
connected after the configuration is saved. After adjusting the configuration in the configuration tool, configure it
by scanning the configuration QR code.
If you need to scan the ID card, you need to configure the output length to 4 in the NFC configuration column of
the configuration tool. Otherwise, it will not be output correctly.
Page 27
Contact Information
Company Name: Beijing Microlight Internet Technology Co., Ltd.
Company Address:
Room 4509~4522, China Meteorological Science and Technology Park, No.2,
Zhenxing Road, Changping District, Beijing
After-sales service: 010-56215600
Business Contact: South China+ Hong Kong, Macau, Taiwan+ Overseas Area: 18910502626
East China + Central China + Southwest China: 18911587949
North China + Northeast China+ Northwest China: 13301399166
www.vguang.cn
28
Page 28
Version Info.
Date
Version
Change description
2017.07.05
1.00
First version
2017.07.06
1.01
Some changes were made on the basis of the first
version
2017.07.06
1.02
The position of some content were adjusted and
part of the data was changed
2017.07.27
1.03
Improvement and modifications
2017.08.15
1.04
Adding the content of default configuration
2017.08.15
1.05
Adding the interface wiring diagram
2017.08.21
1.06
Updating Ethernet related functions
2017.08.30
1.07
Updating several common
configuration codes and FAQs
2017.09.22
1.08
Updating typesetting and a few contents
www.vguang.cn
29
Loading...