High Power N MiniPCI 5.8GHz
2 x 2 802.11N MIMO mini-PCI Modules
XN58-26
5GHz Single-Band 802.11n MIMO 2 x 2 miniPCI
Features
Atheros XSPAN family chipset
•
IEEE 802.11n compliant and backward compatible with 802.11a
•
Enhanced sensitivity
•
Optimized isolation path
•
Superior thermal performance
•
Maximum output power 26dBm@802.11a / 28dBm MIMO aggregate
•
•
Built-in ESD Protection with ESD/EMP Immunity Threshold: 15KeV
•
Multi-Country Roaming Supported (IEEE802.11d Global Harmonization Standard)
•
2 x MMCX connectors allowing for improved mechanical stability and low loss
①
Technical Specifications
Chipset Atheros AR9220
Host Interface 32-bit mini-PCI Type IIIA+ (6.55mm longer than IIIA type)
Operating
Voltage
Power
Consumption
Antenna
Connector
Data Rate
Frequency
Range
Modulation
Techniques
RoHS
Compliance
Temperature
Range
Humidity
Dimension 59.6mm x 57.5mm x 7.5mm
802.11a
3.3 VDC
11a Cont. Tx @6M 4.9W
11na Cont. Tx@HT20 MCS0 4.3W
11na Cont. Tx@HT40 MCS0 4.8W
11a Cont. Rx 2.5W
Standby 0.8W
2 x MMCX connector
IEEE 802.11a : 54Mbps 48Mbps 36Mbps 24Mbps 18Mbps 12Mbps 9Mbps 6Mbps
1Nss: 65Mbps @ 800GI, 72.2Mbps @ 400GI (Max.)
20MHz
IEEE 802.11n :
IEEE 802.11a/n:
OFDM: BPSK, QPSK, 16-QAM, 64-QAM
Yes
Operating: -20ºC to 70ºC
Storage: -40ºC to 90ºC
Operating:5% to 95% (non-condensing)
Storage: Max.90% (non-condensing)
2Nss: 130Mbps @ 800GI, 144.4Mbps @ 400GI (Max.)
1Nss: 135Mbps @ 800GI, 150Mbps @ 400GI (Max.)
40MHz
2Nss: 270Mbps @ 800GI, 300Mbps @ 400GI (Max.)
5.725 ~ 5.850 GHz (US & Canada)
5.725 ~ 5.875 GHz (Europe)
XN58-26 MIMO MINIPCI CARD RADIO
TX SPECIFICATIONS
DataRate TX Power
6-24Mbps 26dBm 28dBm ±2dB
36Mbps 25dBm 28dBm ±2dB
48Mbps 24dBm 27dBm ±2dB
54Mbps 23dBm 26dBm ±2dB
TX Power
Tolerance
5GHz
11n
HT 20
802.11a
5GHz
11n
HT 20
DataRate
MCS 0/8 25dBm 28dBm ±2dB MCS 0/8 24dBm 27dBm ±2dB
MCS 1/9 25dBm 28dBm ±2dB MCS 1/9 24dBm 27dBm ±2dB
MCS 2/10 23.5dBm 26.5dBm ±2dB MCS 2/10 22.5dBm 25.5dBm ±2dB
MCS 3/11 23.5dBm 26.5dBm ±2dB MCS 3/11 22.5dBm 25.5dBm ±2dB
MCS 4/12 22.5dBm 25.5dBm ±2dB MCS 4/12 22dBm 25dBm ±2dB
MCS 5/13 22dBm 25dBm ±2dB MCS 5/13 20.5dBm 23.5dBm ±2dB
MCS 6/14 21dBm 24dBm ±2dB MCS 6/14 20.5dBm 23.5dBm ±2dB
MCS 7/15 20dBm 23dBm ±2dB
DataRate
6M -96dBm ±2dB 24M -89dBm ±2dB
9M -96dBm ±2dB 36M -86dBm ±2dB
12M -95dBm ±2dB 48M -82dBm ±2dB
18M -93dBm ±2dB
MCS0 -95dBm ±2dB MCS0 -92dBm ±2dB
MCS1 -93dBm ±2dB MCS1 -90dBm ±2dB
MCS2 -90dBm ±2dB MCS2 -87dBm ±2dB
MCS3 -89dBm ±2dB MCS3 -84dBm ±2dB
MCS4 -85dBm ±2dB MCS4 -81dBm ±2dB
MCS5 -81dBm ±2dB MCS5 -77dBm ±2dB
MCS6 -79dBm ±2dB MCS6 -76dBm ±2dB
MCS7
TX Power
(per chain)
TX Power
(2 chains)
Sensitivity
(2 chains)
-75dBm ±2dB
Tolerance DataRate
RX SPECIFICATIONS
Tolerance DataRate
5GHz
11n
HT 40
MCS 7/15 17dBm 20dBm ±2dB
802.11a
54M -79dBm ±2dB
5GHz
11n
HT 40
MCS7
TX Power
(per chain)
TX Power
(2 chains)
Sensitivity
(2 chains)
-74dBm ±2dB
Tolerance
Tolerance
ESD CABLE SPECIFICATION
Cable Dimensions 26cm length
Terminal Material Copper
Attachment Procedure End of ESD Cable tied to Earth Ground
②
Ordering Information
CODES Connectors type Carton Dimension
XN58-26
c
Module grounding cable included
Configurations are subject to change without notice
d
Please contact Compex sales representatives for other available configura tions
MMCX
For 50pcs (pcs/ctn), 0.40m * 0.22m * 0.085m / 0.006 = 1.5KG
For 250pc (pcs/ctn), 0.45m * 0.45m * 0.24m / 0.006 = 8.1KG
COMPLIANCE INFORMATION
This device complies with the following radio frequency and safety standards.
Important to OEM Manufacturer:
This following FCC Warning must be included in the HOST User Manual.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF
exposure compliance.
Note 1: This module certified that complies with RF exposure requirment under mobile or fixed condition,
this module is to be installed only in mobile or fixed applications.
A mobile device is defined as a transmitting device designed to be used in other than fixed
locations and to generally be used in such a way that a separation distance of at least 20
centimeters is normally maintained between the transmitter's radiating structure(s) and the
body of the user or nearby persons. Transmitting devices designed to be used by consumers or
workers that can be easily re-located, such as wireless devices associated with a personal
computer, are considered to be mobile devices if they meet the 20 centimeter separation
requirement.
A fixed device is defined as a device is physically secured at one location and is not able to be
easily moved to another location.
Note 2: Any modifications made to the module will void the Grant of Certification, this
module is limited to OEM installation only and must not be sold to end-users, end-user has no
manual instructions to remove or install the device, only software or operating procedure shall
be placed in the end-user operating manual of final products.
Note 3: The device must not transmit simultaneously with any other antenna or transmitter.
Note 4: To ensure compliance with all non-transmitter functions the host manufacturer is
responsible for ensuring compliance with the module(s) installed and fully operational. For
example, if a host was previously authorized as an unintentional radiator under the
Declaration of Conformity procedure without a transmitter certified module and a module is
added, the host manufacturer is responsible for ensuring that the after the module is installed
and operational the host continues to be compliant with the Part 15B unintentional radiator
requirements. Since this may depend on the details of how the module is integrated with the
host, Microhard System Inc. shall provide guidance to the host manufacturer for compliance
with the Part 15B requirements.
Note 5: FCC ID label on the final system must be labeled with “Contains FCC ID:
NS912XN58-26” or “Contains transmitter module FCC ID: NS912XN58-26”.
The transmitter module must be installed and used in strict accordance with the manufacturer's
instructions as described in the user documentation that comes with the host product.
Microhard Systems Inc. is responsible for the compliance of the module in all final hosts.
IMPORTANT NOTE REGARDING ANTENNA USE
Antenna Use (Point to Multipoint)
2x2 Operation
Chain1 Chain2
Dimensions Drawing
Microhard Systems Inc
Address: 150 Country Hills Landing NW Calgary Alberta Canada
Contact Name: Hany Shenouda
Tel. No: 403-248-0028
Fax No: 403-248-2762
Email: shenouda@microhardcorp.com
For more information, visit www.compex.com.sg
Loading...