Microhard Systems 15NM2458 Users manual

Operating Manual

nMIMO2458

2.4/5.8 GHz High Speed 1W Module

Revision 0.8, November 26, 2015

Phone: [phone]
Fax: [phone]

www.microhardcorp.com

Microhard Systems Inc.

Warranty

Microhard Systems Inc. warrants that each product will be free of defects in material and workmanship for a period of one (1)
year for its products. The warranty commences on the date the product is shipped by Microhard Systems Inc. Microhard Systems
Inc.’s sole liability and responsibility under this warranty is to repair or replace any product which is returned to it by the Buyer
and which Microhard Systems Inc. determines does not conform to the warranty. Product returned to Microhard Systems Inc. for
warranty service will be shipped to Microhard Systems Inc. at Buyer’s expense and will be returned to Buyer at Microhard

Systems Inc.’s expense. In no event shall Microhard Systems Inc. be responsible under this warranty for any defect which is

caused by negligence, misuse or mistreatment of a product or for any unit which has been altered or modified in any way. The
warranty of replacement shall terminate with the warranty of the product.

Warranty Disclaims

Microhard Systems Inc. makes no warranties of any nature of kind, expressed or implied, with respect to the hardware, software,
and/or products and hereby disclaims any and all such warranties, including but not limited to warranty of non-infringement,
implied warranties of merchantability for a particular purpose, any interruption or loss of the hardware, software, and/or product,
any delay in providing the hardware, software, and/or product or correcting any defect in the hardware, software, and/or product,
or any other warranty. The Purchaser represents and warrants that Microhard Systems Inc. has not made any such warranties to
the Purchaser or its agents MICROHARD SYSTEMS INC. EXPRESS WARRANTY TO BUYER CONSTITUTES

MICROHARD SYSTEMS INC. SOLE LIABILITY AND THE BUYER’S SOLE REMEDIES. EXCEPT AS THUS

PROVIDED, MICROHARD SYSTEMS INC. DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PROMISE.

MICROHARD SYSTEMS INC. PRODUCTS ARE NOT DESIGNED OR INTENDED TO BE USED IN
ANY LIFE SUPPORT RELATED DEVICE OR SYSTEM RELATED FUNCTIONS NOR AS PART OF

ANY OTHER CRITICAL SYSTEM AND ARE GRANTED NO FUNCTIONAL WARRANTY.

Indemnification

The Purchaser shall indemnify Microhard Systems Inc. and its respective directors, officers, employees, successors
and assigns including any subsidiaries, related corporations, or affiliates, shall be released and discharged from any
and all manner of action, causes of action, liability, losses, damages, suits, dues, sums of money, expenses
(including legal fees), general damages, special damages, including without limitation, claims for personal injuries,
death or property damage related to the products sold hereunder, costs and demands of every and any kind and
nature whatsoever at law.

IN NO EVENT WILL MICROHARD SYSTEMS INC. BE LIABLE FOR ANY INDIRECT, SPECIAL,
CONSEQUENTIAL, INCIDENTAL, BUSINESS INTERRUPTION, CATASTROPHIC, PUNITIVE OR OTHER
DAMAGES WHICH MAY BE CLAIMED TO ARISE IN CONNECTION WITH THE HARDWARE,
REGARDLESS OF THE LEGAL THEORY BEHIND SUCH CLAIMS, WHETHER IN TORT, CONTRACT OR
UNDER ANY APPLICABLE STATUTORY OR REGULATORY LAWS, RULES, REGULATIONS,
EXECUTIVE OR ADMINISTRATIVE ORDERS OR DECLARATIONS OR OTHERWISE, EVEN IF
MICROHARD SYSTEMS INC. HAS BEEN ADVISED OR OTHERWISE HAS KNOWLEDGE OF THE
POSSIBILITY OF SUCH DAMAGES AND TAKES NO ACTION TO PREVENT OR MINIMIZE SUCH
DAMAGES. IN THE EVENT THAT REGARDLESS OF THE WARRANTY DISCLAIMERS AND HOLD
HARMLESS PROVISIONS INCLUDED ABOVE MICROHARD SYSTEMS INC. IS SOMEHOW HELD
LIABLE OR RESPONSIBLE FOR ANY DAMAGE OR INJURY, MICROHARD SYSTEMS INC.'S LIABILITY
FOR ANYDAMAGES SHALL NOT EXCEED THE PROFIT REALIZED BY MICROHARD SYSTEMS INC.
ON THE SALE OR PROVISION OF THE HARDWARE TO THE CUSTOMER.

Proprietary Rights

The Buyer hereby acknowledges that Microhard Systems Inc. has a proprietary interest and intellectual property rights in the
Hardware, Software and/or Products. The Purchaser shall not (i) remove any copyright, trade secret, trademark or other evidence
of Microhard Systems Inc.’s ownership or proprietary interest or confidentiality other proprietary notices contained on, or in, the
Hardware, Software or Products, (ii) reproduce or modify any Hardware, Software or Products or make any copies thereof, (iii)
reverse assemble, reverse engineer or decompile any Software or copy thereof in whole or in part, (iv) sell, transfer or otherwise
make available to others the Hardware, Software, or Products or documentation thereof or any copy thereof, except in accordance
with this Agreement.

ii nMIMO2458 Operating Manual

nMIMO2458 Regulatory Requirements

Contains:
FCC ID: NS915NM2458 IC : 3143A-15NM2458

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this
device must accept any interference received including
interference that may cause undesired operation.

WARNING:

To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of 23 cm (33cm IC) or more should be
maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance
is not recommended. The antenna used for this transmitter must not be co-located in conjunction with any other antenna or transmitter.

WARNING:

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received including interference that may cause undesired operation.

WARNING:

Changes or modifications not expressly approved by Microhard Systems Inc. could void the user’s authority to operate the equi pment. This device
has been tested with UFL to Reverse Polarity SMA connectors with the antennas listed in Appendix A When integrated in OEM products, fixed
antennas require installation preventing end-users from replacing them with non-approved antennas. Antennas not listed in the tables must be
tested to comply with FCC Section 15.203 (unique antenna connectors) and Section 15.247 (emissions).

WARNING:

MAXIMUM EIRP: Cannot exceed 31.51 dBm EIRP in 2.4 GHz band. Therefore, the sum of the transmitted power (in dBm), the cabling loss
and the antenna gain cannot exceed 31.51 dBm.

WARNING:

MAXIMUM EIRP: For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz
shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation.

WARNING:

Be advised that high-power radars are allocated as primary users (i.e.prioirty users) of the bands 5250-535 0 MHz and 5650-5850 MHz and
that these radars could cause interference and/or damage to LE-LAN devices.

WARNING:

EQUIPMENT LABELING: The FCC and IC numbers depend on the model of the radio module. Do NOT use the Marketing Name of the
product but the Model to distinguish the Certifications Numbers. This device has been modularly approved. The manufacturer, product
name, and FCC and Industry Canada identifiers of this product must appear on the outside label of the end-user equipment.

WARNING:

This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired
operation of the device.

WARNING:

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:

SAMPLE LABEL REQUIREMENT for Model: nMIMO2458:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

iii

nMIMO2458 Exigences Réglementaires

Contains:
FCC ID: NS915NM2458 IC : 3143A-15NM2458

Cet appareil est conforme à la partie 15 des règles de
la FCC . Son fonctionnement est soumis aux deux
conditions suivantes : ( 1 ) ce dispositif ne doit pas
causer d'interférences nuisibles et ( 2) cet appareil
doit accepter toute interférence reçue, incluant les
interférences qui peuvent provoquer un
fonctionnement indésirable .

WARNING:

Pour satisfaire aux exigences de la FCC d'exposition RF pour la base et mobiles sur une distance de séparation de 23 cm (33cm IC) ou plus
doit être maintenue entre l'antenne de cet appareil et des personnes lors de fonctionnement du dispositif. Pour assurer la conformité des
opérations au plus près que cette distance n'est pas recommandée. L'antenne utilisée pour ce transmetteur ne doit pas être co-localisés en
conjonction avec toute autre antenne ou transmetteur.

WARNING:

Son fonctionnement est soumis aux deux conditions suivantes : ( 1 ) ce dispositif ne doit pas causer d'interférences nuisibles et ( 2) cet appareil doit
accepter toute interférence reçue, incluant les interférences qui peuvent provoquer un fonctionnement indésirable .

WARNING:

Les changements ou modifications non expressément approuvés par Microhard Systems Inc. pourraient annuler l'autorité de l'utilisateur à
utiliser l'équipement . Ce dispositif a été testé avec UFL et connecteurs SMA à polarité inverse sur les antennes répertoriées à l'annexe A Lorsqu'il
est intégré dans les produits OEM , antennes fixes nécessitent une installation empêchant les utilisateurs finaux de les remplacer par des antennes
non approuvées . Antennes ne figurant pas dans les tableaux doivent être testés pour se conformer à la Section 15.203 (connecteurs d'antenne
uniques ) et à la Section 15.247 ( émissions ) .

WARNING:

MAXIMUM EIRP: Vous ne pouvez pas dépasser 31.51 dBm EIRP dans la bande de 2,4 GHz. Par conséquent, la somme de la puissance émise ( en
dBm ), la perte de câblage et le gain d'antenne ne peut pas dépasser 31.51 dBm.

WARNING:

MAXIMUM EIRP: Pour les appareils avec antenne ( s) détachable , le gain d'antenne maximal autorisé pour les appareils dans la bande 5725-5850
MHz doit être telle que l'équipement satisfait encore la pire limites spécifiées pour un fonctionnement point à point et non point -à-point.

WARNING:

Soyez avisé que les radars à haute puissance sont désignés comme utilisateurs principaux ( ieprioirty utilisateurs) des bandes 5250-535 0 MHz et
de 5650 à 5850 MHz et que ces radars pourraient provoquer des interférences et / ou endommager les appareils LE- LAN .

WARNING:

ÉQUIPEMENT DE MARQUAGE: Les numéros FCC et IC dépendent du modèle du module radio . Ne pas utiliser le nom marketing du produit,
mais le modèle de distinguer les numéros Certifications . Ce dispositif a été approuvé de façon modulaire . Le fabricant , nom du produit, et les
identificateurs de la FCC et d'Industrie Canada de ce produit doivent figurer sur l'étiquette à l'extérieur de l'équipement de l'utilisateur final .

WARNING:

Cet appareil est conforme aux CNR exempts de licence d'Industrie Canada . Son fonctionnement est soumis aux deux conditions suivantes : ( 1 )
Ce dispositif ne peut causer des interférences ; et ( 2 ) Ce dispositif doit accepter toute interférence , y compris les interférences qui peuvent causer
un mauvais fonctionnement de l'appareil.

WARNING:

NOTE : Cet équipement a été testé et jugé conforme aux limites d' un dispositif numérique de classe B, conformément à la partie 15 des règles de
la FCC . Ces limites sont conçues pour fournir une protection raisonnable contre les interférences nuisibles dans une installation résidentielle . Cet
équipement génère , utilise et peut émettre de l'énergie radiofréquence et, si non installé et utilisé conformément aux instructions , peut provoquer
des interférences dans les communications radio . Cependant , il n'y a aucune garantie que des interférences ne se produiront pas dans une
installation particulière . Si cet équipement provoque des interférences nuisibles à la réception radio ou de télévision , ce qui peut être déterminé
en allumant et éteignant l'équipement , l'utilisateur est encouragé à essayer de corriger l'interférence par une ou plusieurs des mesures suivantes :

SAMPLE LABEL REQUIREMENT for Model: nMIMO2458:

iv nMIMO2458 Operating Manual

- Réorienter ou déplacer l'antenne de réception .

- Augmentez la distance entre l' équipement et le récepteur.

- Connecter l'équipement à une sortie sur un circuit différent de celui sur lequel est branché le récepteur.

- Consulter le revendeur ou un technicien radio / TV expérimenté.