Microh Profile Spot PZM User Manual

1) Open the box and checking Page 1

2) Safety instructions Page 1

3) Operating determinations Page 2

4) Description of the device Page 3

5) Installation Page 4

6) Control Board Operation Page 8

7) DMX512 Channel Function Page 9

8) Technical specifications Page 18

9) Beampath Page 19

10)Maintenance and cleaning Page 20

11) Structure of the fixture Page 21

12) Electrical diagram Page 22

13) Common faulty maintain Page 23

14) Component antitheses Page 24

15) Main PCB Page 26

16) Display PCB Page 27

17) Driver(L) PCB Page 28

18) Driver(S) PCB Page 29

1.Open the box and checking

Congratulations on choosing our products! Please carefully read this instruction manual in its
entirety and keep it well for using reference. This manual contained about the installation and the
relative using information of this products. Please according to this manual's relative speaking when
using this equipment.

This equipment was made of new style, high intensity plastic . It fully shows the modem times
light characteristic with beauty structure. And it was made according to CE standard. Fully up the
international standard of DMX512 agreement. Master or slave in phase control. Can be use in large
entertainment, theater, performing and playing hall, etc.

This product uses MSD 250 or MSD 250/2 electrical arc lamp. When receiving this product
please carefully bring and put; and check that whether this equipment has been damaged or not
during transportation. And please also check the following thing was enclosed:

Signal line ----------------------- one piece Safety string -----------------------one piece

User Manual-----------------------one set Omega -holder----------------------two pieces

2. Safety instructions

Every person involved with installation and maintenance of this device have to:

- be qualilfied

- follow the instructions of this manual

CAUTION:

Ø Keep this device away from rain and moisture!
Ø Unplug mains lead before opening the housing!
Ø FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
Ø BEFORE YOU INITIAL START - UP!
Ø Be careful with your operations.
Ø With a high voltage you can suffer a dangerous electric shock when touching the

wires!

Ø This device has left our premises in absolutely perfect condition. In order to maintain

this condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this manual.

Important:

Ø The manufacturer will not accept liability for any resulting damages caused by the non-

observance of this manual or any unauthorized modification to the device.

Ø Please consider that damages caused by manual modifications to the device are not

subject to warranty.

Ø Never let the power-cord come into contact with other cables! Handle the power-cord

and all connections with the mains with particular caution!

Ø Make sure that the available voltage is not higher than stated on the rear panel.
Ø Always plug in the power plug least. Make sure that the power-switch is set to OFF-

position before you connect the device to the mains. The power-plug has to be access
able after installing the device.

Ø Make sure that the power-cord is never crimped or damaged by sharp edges. Check the

device and the power cord from time to time.

1

Ø by the plug. Never pull out the plug by tugging the power-cord.
Ø This device falls under protection class I. Therefore it is essential to connect the

yellow/green conductor to earth.

Ø The electric connection, repairs and servicing must be carried out by a qualified

employee.

Ø Do not connect this device to a dimmer pack.
Ø Do not switch the fixture on and off in short intervals as this would reduce the lamp' s

life.

Ø During the initial start-up some smoke or smell may arise. This is a normal process and

does not necessarily mean that the device is defective.

Ø Do not touch the device's housing bare hands during its operation (housing becomes hot)!
Ø For replacement use lamps and fuses of same type and rating only.

CAUTION :

EYE DAMAGES !
Avoid looking directly into the light source(meant especially for epileptics) !

Ø

Ø

Ø
Ø
Ø

Ø

Ø

Ø

Ø

Ø

Ø

3. Operating determinations

This device is a moving-head spot for creating decorative effects and was designed for
indoor use only.
If the device has been exposed to drastic temperature fluctuation (e.g. After transport­ation), do not switch it on immediately. The arising condensation water might damage
your device. Leave the device switched off until it has reached room temperature.
Never run the device without lamp!
Do not shake the device. Avoid brute force when installing or operating the device.
Never lift the fixture by holding it at the projector-head, as the mechanics may be
damaged. Always hold the fixture at the transport handles.
When choosing the installation-spot, please make sure that the device is not exposed to
extreme heat, moistureor dust. There should not be any cables lying around. You
endanger your own and the safety of others!
The minimum distance between light-output and the illuminated surface must be more
than 2 meters.
Make sure that the area below the installation place is blocked when rigging, derigging
or servicing the fixture. Always fix the fixture with an appropriate safety-rope. Fix the
safety-rope at the correct holes only.
Only operate the fixture after having checked that the housing is firmly closed and all
screws are tightly fastened.
The lamp must never be ignited if the objective-lens or any housing-cover is open, as
discharge lamps may explose and emit a high ultraviolet radiation, which may cause
burns.
The maximum ambient temperature ta = 45 must never be exceeded. Otherwise, the
lamp is switched off and the fixture is out of operation for 5 minutes..

2

4.Description of the device

Front panel:

10 -

Mode-button
11 - Enter-button
12 - Up-button

13 - Down-button
14

- Display

Rear panel:
5 - Power switch
6 - DMX output

7 - DMX input
8 - Power cord
9 - Fuse holder

1 - Moving head
2 - Yoke
3 - Carry handles
4 - Base

POWER SWITCH

POWER SUPPLY

T 3.15A@230V
T 6.3A@120V

LAMP:MSD 250/2

MSD 250

FUSE

1=GND
2=SIG.­3=SIG.+

SERIAL DATA LINK

LIGHTING CONTROL PROTOCOL:DMX512

OUT DMX INOUT DMX IN

Serial number:

3

5.2 Lamp adjust

The lamp holder is aligned at the factory. Due to differences between lamps , fine

adjustment may improve light performance. Strike the lamp, open the shutter and the iris,

set the dimmer intensity onto 100% and focus the light on a flat surface (wall). As the
optimum distance of the lamp from lens was adjusted during the installing or changing the
lamp (by turning the screw "A"), it is necessary to adjust only the second position by
turning the screw "B", in order to center the hot-spot (the brightest part of the beam). If
the hot spot seems to be too bright, you can lower its intensity by moving the lamp closer to
the reflector. Do so by turning the screw "A" until the light is evenly distributed. If the
light on the edge seems to be brighter as in the center, the lamp is too close at the reflector.
In this case, you need to move the lamp away from the reflector until the light is evenly
distributed and the beam appears bright enough.

1-1,5 mm

Optimum distance

Screw¡°B¡±

Screw A

Correct

WARNING!

Lamp is hot! Risk of fire! Protect hands and eyes.

Wait at least 15min. Before opening the covers

and removing lamp from the fixture.

Minimum distance to lighted object:
Maximum room temperature ta=45

Minimum distance from flammable material d=0.5m.

Exterior surface temperature T=80 .

Not for domestic use.

Be sure that the lamp

bulb never touch the lens

Disconnect the fixture from AC power

before re-lamping.

1.3m

A

B

Adjust lamp position by turning screws and

Incorrect

Turn off the lamp and allow it to cool for at least 10 minutes. Disconnect the fixture from
power. To insert the gobos open the top cover of the moving-head by loosening the 3 screws
on the top cover and follow the instructions below:

Rotating gobo-wheel:

Press the ends of the fixation-ring together with an appropriate tool and remove it.
Remove the gobo and insert the new gobo. Press the ends of the fixation-ring together and
insert it in the front of the gobo.

5.3Inserting/Exchanging gobos

5

5.4 Rigging the fixture

DANGER TO LIFE:Please consider the respective national norms during the
installation!The installation must only be carried out by an authorized dealer!

Ø The installation of the projector has to be built and constructed in a way that it can hold 10

times the weight for 1 hour without any harming deformation.

Ø The installation must always be secured with a secondary safety attachment, e.g. an

appropriate catch net. This secondary safety attachment must be constructed in a way that
no part of the installation can fall down if the main attachment fails.

Ø When rigging, derigging or servicing the fixture staying in the area below the installation

place, on bridges, under high working places and other endangered areas is forbidden.

Ø The operator has to make sure that safety-relating and machine-technical installations are

approved by an expert before taking into operation for the first time and after changes
before taking into operation another time.

Ø The operator has to make sure that safety-relating and machine-technical installations are

approved by an expert after every four year in the course of an acceptance test.

Ø The operator has to make sure that safety-relating and machine-technical installations are

approved by a skilled person once a year.

Ø The projector should be installed outside areas where persons may walk by or be seated.
Ø IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE,

including (but not limited to)calculating working load limits, installation material being
used, and periodic safety inspection of all installationmaterial and the projector. If you
lack these qualifications, do not attempt the installation yourself, but instead use a
professional structural rigger. Improper installation can result in bodily injury and or
damage to property.

Ø The projector has to be installed out of the reach of people.
Ø If the projector shall be lowered from the ceiling or high joists, professional trussing

systems have to be used. The projector must never be fixed swinging freely in the room.

Ø Caution: Projectors may cause severe injuries when crashing down! If you have doubts

concerning the safety of a possible installation, do NOT install the projector!

Ø Before rigging make sure that the installation area can hold a minimum point load of 10

times the projector s weight.

Colour/Static gobo-wheel:

Gently bend out the gobo holder to release it from the fixative holes and eject it from the
pressing snap. Press the ends of the fixation-ring together with an appropriate tool and
remove it. Remove the gobo and insert the new gobo. Press the ends of the fixation-ring
together and insert it in the front of the gobo. Put the gobo holder back under the pressing
snap and push it to the 3 fixative notches.

gobo

holder

pressing snap

6

5.5 Connection to the mains

Verify the power supply settings before applying power!

If you wish to change the power supply settings,see the chapter Appendix.
Connect the fixture to the mains with the enclosed power cable and plug.
The earth has to be connected!

The occupation of the connection-cables is as follows:

Pin

Cable (EU)

International

Brown
Light blue

Yellow/Green

Black

White

Green

Live

Neutral

Earth

Cable (US)

Ø The projector can be placed directly on the stage floor or rigged in any orientation on a

truss without altering its operation characteristics.

Ø For overhead use, always install a safety-rope that can hold at least 10 times the weight of

the fixture. You must only use safety-ropes with screw-on carabines. Pull the safety-rope
through the two apertures on the bottom of the base and over the trussing system etc.
Insert the end in the carabine and tighten the fixation screw.

5.6 DMX-512 connection/connection between fixtures

Secure chainSecure chain

Eye boltEye bolt

Mounting plateMounting plate

ClampClamp

Omega-holde Omega-holde

7

Function Table:

Only use a stereo shielded cable and 3-pin XLR-plugs and connectors in order to connect the
controller with the fixture or one fixture with another.

DMX-OUTPUT

DMX-input

1- Ground
2 - Signal (-)
3 - Signal (+)

11 - Ground

2 - Signal (-)
3 - Signal (+)

Occupation of the XLR-connection:

XLR mounting-socket:

XLR mounting-plug:

Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a
120 resistor between Signal (-) and Signal (+) into a 3-pin XLR-plug and plug it in the
DMX-output of the last fixture.

The transform of the controller line of 3 pins and 5 pins (plug and socket)

6. Control Board Operation

Mode

Function

Condition

Pan movement in positive or negative direction

YES--negative direction

YES--negative direction

Vertical movement in positive or negative direction

Address code set

Reset

Rainbow color wheel change color linear or stepping

YES--reset

YES--linear

Working mode

DMX512 mode

Automatic

Slave mode

Lamp switch

Lamp on
Lamp off

Software version

Lamp hot

Lamp error

8

MODEMODE

ENTERENTER

UPUP

DOWNDOWN

Control board operation way:

1.Select working mode by pressing MODE.

2.Press ENTER to confirm the selection.

3.Press UP and DOWN to select working condition.

4.Press ENTER to confirm the selection.

LED

7. DMX512 Channel Function

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

CHANNEL

PAN

TIL T

PAN FINE(proportional)

TILT FINE(proportional)

Speed of PAN/TILT movement

Lamp on/off & reset

Colors 1

Static gobos/colors 2

Prism

3-facet Prism rotation

Rotating gobos

Rotating gobo index, rotating gobo rotation

Zoom, frost, UV filter

Focus(proportional)

Shutter/ strobe

Dimmer intensity(proportional)

FUNCTION

9

CHANNEL 2: TILT

CHANNEL 1: PAN

Value

Effect

Anti-clockwise
280 rotate

255

0

100

0

Value

Effect

Clockwise 0
rotate

53

255

0

100

0

10

CHANNEL 4: TILT FINE (proportional)

CHANNEL 3: PAN FINE (proportional)

• •

Fine control of tilt
movement

Fine control of
tilt movement

Value

Effect

Value

Effect

255

0

100

0

255

0

100

0

11

CHANNEL 5: Speed of PAN/TILT movement

Value

Effect

fast

Slow

Fast

Slow

Value

Effect

•

CHANNEL 6: Lamp on/off & reset

240-255

230-239

140-229

128-139

0-127

0-49

50-54

55-90

91-94

95-100

No function

No function

No function

255

0

100

0

Lamp off after 3
seconds

Lamp on after 3
seconds,Reset

12

CHANNEL 7: Color1

CHANNEL 8: Static gobo /color2

Value

Effect

128-255

112-127

96-111

80-95

64-79

48-63

32-47

16-31

0-15

50-100

44-49

37-43

31-36

25-30

19-24

12-18

6-11

0-5

Forwards rainbow

Pink

Blue

Orange

Green

Magenta

Yellow

Red

Open/white

effect from slow to fast

Light Blue

Pale purple

Light Orange

Static gobo 3

Static gobo 2

Static gobo 1

White

222-255

185-221

148-184

111-147

74-110

37-73

0-36

87-100

72-86

57-71

43-56

28-42

14-27

0-13

Value

Effect

13

CHANNEL 9: Prism

Value

Effect

CHANNEL 10: 3-facet prism rotation

Value

Effect

128-255

0-127 0

100

No function

3-facet prism

133-255

128-132

5-127

0-4 0-2

3-50

51-52

53-100

No rotation

No rotation

Backwards rotation
from slow to fast

Forwards rotation
from fast to slow

14

Rotate gobo wheel
continue rotation

from slow to fast

CHANNEL 11: Rotating gobos

Value

Effect

Rotate gobo 5

Rotate gobo 4

Rotate gobo 3

Rotate gobo 2

Rotate gobo 1

Open/hole

CHANNEL 12:Rotating gobo index, rotating gobo rotation

159-255

61-158

0-60

Value

Effect

0-23

62-100

24-61

224-255

160-223

128-159

96-127

64-95

32-63

0-31

88-100

63-87

50-62

37-49

25-36

12-24

0-11

Gobo indexing (0-540 )

Backwards gobo rotation
from slow to fast

Forwards gobo rotation
from slow to fast

15

CHANNEL 14: Focus(proportional)

Value

Effect

CHANNEL 13: Zoom,frost,UV filter

Value

Effect

240-255

224-239

208-223

192-207

176-191

160-175

128-159

112-127

96-111

80-95

64-79

48-63

32-47

0-31

93-100

87-92

82-86

75-81

68-74

62-67

50-61

43-49

37-42

31-36

24-30

18-23

12-17

0-11

UV-filter

Frost

Zoom 26

Zoom 24

Zoom21

Zoom 18

Zoom 15

UV-filter

Frost

Zoom 26

Zoom 24

Zoom21

Zoom 18

Zoom 15

Zoom without focus corectionZoom without focus corection

Near

Far

close distance

far distance0 0

100

255

16

CHANNEL 15:Shutter, strobe

Value

Effect

Value

Effect

Black

Brightest

Brightest

Black

CHANNEL 16: Dimmer intensity(proportional)

Shutter Open

Shutter Open

Shutter Open

Shutter Open

Shutter closed

224-255

192-223

160-191

128-159

96-127

64-95

32-63

0-31

87-100

75-86

62-74

50-61

37-49

25-36

12-24

0-11

Random strobe-

effect from slow
to fast

Pulse-effect in

sequences from
slow to fast

Strobe-effect from
slow to fast (max
10flashes/s)

255

0

100

0

17

8. Technical specifications

US-model: Voltage............................AC100/110/120V , 50/60Hz

Fuse................................ T 6.3 A@120V

EU-model:Voltage............................AC220/230/240V ,50/60Hz

Fuse ................................T3.15

Rated Power 350W

DMX512 Channel 16CHS

Luminous 18000 LM

Philips MSD250/2 or MSD 250 GY 9,5

Focus: Linear electric focus

Zoom: Motorized multi-step-zoom with five different apertures (15 , 18 , 21 ,

24 , 26 )

Color:

7dichroic-filters plus white,colour-wheel with variable rotation speed in both directions

Strobe: Variable speed (1-10 flashes/sec)

Rigging:

-Stands directly on the floor

-Mounts horizontally or vertically with 2 clamps

-1 truss orientation

-Safety chain/cord attachment bolt

Temperatures

-Maximum ambient temperature ta: 45

-Maximum housing temperature tb (steady state): 80

Minimum distances:

-Min.distance from flammable surfaces: 0.5m

-Min.distance to lighted object: 2.0m

Dimmer: Smooth dimmer 0-100%

Pan / Tilt Movement:

-Pan 530 , Tilt 280

-Micro-step scan effect

-Auto-repositioning by photoelectric repositioning system

-Linearity move speed adjust.

Prisms: 3-facet prism (dual direction rotation with adjustable speed)

Dimensions and weight:

-Length of base (including handles): 400 mm

-Width of yoke: 400 mm

-Height (head horizontal): 476 mm

-Weight (net): 26 kg

A @230V

Lamp:

Optical System:

-

-

-

18

9. Beampath

19

15 radiation angle

24 radiation angle

18 radiation angle

26 radiation angle

21 radiation angle

15 radiation angle with frost

26 radiation angle with frost

369

3970

92

990

41

440

23 Foot-candles
250 LUX

20 Distance(m)
5,27 Diameter(m)

15

3,95

10

2,63

5

1,30

3

2

1

0

1

2

3

Beam opening (m)

Beam opening (m)

5

4

3

2

1

0

1

2

3

4

5

180

1940

45

485

20

215

11 Foot-candles
120 LUX

20 Distance(m)
8,50 Diameter(m)

15

6,38

10

4,25

5

2,13

18 Foot-candles
190 LUX

33
355

70

755

281

3020

4

3

2

1

0

1

2

3

4

Beam opening (m)

20 Distance(m)
6,34 Diameter(m)

Beam opening (m)

5

4

3

2

1

0

1

2

3

4

5

147

1580

37

395

16

175

9 Foot-candles
100 LUX

4

3

2

1

0

1

2

3

4

Beam opening (m)

5

1,58

10

3,17

15

4,75

241

2600

60

650

27

290

15 Foot-candles
160 LUX

20 Distance(m)
7,41 Diameter(m)

15

5,56

10

3,70

5

1,85

5

2,30

10

4,62

15

6,93

20 Distance(m)
9,20 Diameter(m)

6 Foot-candles
65 LUX

11

114

24

256

95

1024

5

2,49

10

4,99

15

7,48

20 Distance(m)
9,97 Diameter(m)

Beam opening (m)

5

4

3

2

1

0

1

2

3

4

5

223

2400

56

600

25

267

14 Foot-candles
150 LUX

5

1,49

10

2,99

15

4,48

20 Distance(m)
5,98 Diameter(m)

3

2

1

0

1

2

3

Beam opening (m)

10. Maintenance and cleaning

It is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid
residues must not buildup on or within the fixture. Otherwise, the fixtures light-output will
be significantly reduced. Regular cleaning willnot only ensure the maximum light-output,
but will also allow the fixture to function reliably throughout its life.A soft lint-free cloth
moistened with any good glass cleaning fluid is recommended, under no circumstances
should alcohol or solvents be used!

DANGER :Disconnect from the mains before starting anymaintenance work

The front objective lens will require weekly cleaning as smoke-fluid tends to building up
residues, reducing thelight-output very quickly. The cooling-fans should be cleaned

monthly.

The gobos may be cleaned with a soft brush. The interior of the fixture should be cleaned

at least annually usinga vacuum-cleaner or an air-jet.

The dichroic colour-filters, the gobo-wheel and the internal lenses should be cleaned
monthly.
To ensure a proper function of the gobo-wheel , we recommend lubrication in six month

intervals. The quantity of oil must not be excessive in order to avoid that oil runs out when

the gobo-wheel rotates.
There are no serviceable parts inside the device except for the lamp and the fuse.Please
refer to the instructions under "Fitting/Exchanging the lamp".Maintenance and service
operations are only to be carried out by authorized dealers.

Replacing the fuse

If the lamp burns out, the fine-wire fuse of the device might fuse, too. Only replace the

fuse by a fuse of same type and rating.Before replacing the fuse, unplug mains lead.

Procedure:

1) Unscrew the fuseholder on the rear panel of the base with a fitting screwdriver from the
housing (anti- clockwise).

2) Remove the old fuse from the fuseholder.

3) Install the new fuse in the fuseholder.

4) Replace the fuseholder in the housing and fix it.

20

21

11. Structure of the fixture

Transformer

Bottom Fan

Seat cover

Pan Motor

Main PCB

DMX512socket

Ballast

Capacitance

Display Board

Driver Board S

Driver Board L

Arm

Tilt motor

Belt

light head Fan

Lamp holder

Lamp

Color wheel

Top cover

Reflector

Rotathng gobo wheel

Stathc gobo wheel

Light shield board

22

+

+

+

+

+

-

-

-

-

-

S

S

S2

S2

S2

S1

S1

S1

+

-

S mix gobo

Horae 4B PCB
Mix gobo

Horae 3C PCB
FOCUS

32uF250V
Capaciance

Tilt

Gobo
wheel

Gobo
rotation

Zoom

Colour

MOTOR5

MOTOR6

MOTOR7

MOTOR8

MOTOR9

Prism
wheel

Prism
rotation

Mix
gobos

MOTOR10

MOTOR11

MOTOR12

Pan

MOTOR4

Focus

MOTOR3

Shutter1

Shutter2

MOTOR2

MOTOR1

LAMP

LP

B

N

THERMOSTAT

IGNITOR

E

E

573

7805

7805

573

3771

75176

TILT
Horge

PAN
Sensor

TILT
Sensor

1

2

3

1

2

3

DMX IN

DMX OUT

RELAY

12V

12V

12VDC

12VDC

DC

DC

30V

30VDC

30VDC

0V

0V

0VDC

0VDC

PAN
Horge

+

-

S2

S1

+

S

-

+

S

-

+

S

-

+

S2
S1

-

+

S2
S1

-

1

2

3

11V

24V

0V

230V

250V

TRANSFORMER

BOTTOM 12VDC FAN

LIGHT HEAD
12VDC FAN
2Pcs

DISPLAY CPU

DISPLAY PCBDISPLAY PCB

RED

RED

BLUE

BLUE

11VAC

24VAC

Horae 4 PCB
Rotation gobo wheel

Horae 3B PCB
Colour

Horae 5 PCB
Zoom

+

-

S colour

S gobo

+

S

-

+

S

-

+

S

-

MAIN PCBMAIN PCB

2107L PCB2107L PCB

2107S PCB2107S PCB

250V/50Hz

230V/50Hz

230V

230V

250V

250V

230V/60Hz

60Hz

IN

BALLAST

L1

N3

U2 U4

Filter

1

2

3

Ic1

Ic2

Ic3

Ic4 Ic5

Ic6 Ic7

Ic8

Ic9 Ic10

Ic13

Ic14

Ic15

Ic16

Ic17

Ic21

Ic22

Ic23

Ic24

Ic25

Ic26

Ic18

Ic19

Ic20

Ic11

Ic12

CPU

CPU

CPU

Connection set

Transmission line

FUSE

T3.15A 250V
(SLOW)

L

N

230V/50Hz

POWER SWITCH

7805

-

-

+

+

S

77E58

+

S

-

12. Electrical diagram

FAULTY PART PART No.

PLUG CABLE

FUSE

POWER SWITCH

HTI 300W/DX

B ELECTRONIC TRIGGER

110 10A/250V

TEMPERATURE S WITCH

250W BALLAST

MAIN PCB

SHOW BOARD

TRANSFORMER 110V)

TRANSFORMER 230V)

REALY FAULTY

80*80*25 12VDC FAN

80*80*25 12VDC FAN

SHOW BOARD FAULTY

MOTOR FOR DIMMER FAULTY

HOLDER FOR FOUCE FAULTY HOLDER FOR FOUCE

FOCUS FOR SCREW THREAD

AXES FAULTY

FOCUS FOR SCREW THREAD

AXES

FOCUS AXES OF SHEATH

FAULTY

FOCUS AXES OF SHEATH

STROBE CAN NOT

WORK

MOTOR FOR STROBE FAULTY

42BYGH004-02MOTOR 15-00-0073-01

MOTOR FOR PAN FAULTY 23HS0001-02MOTOR

STRAP OF PAN BREAK

23HS0001-02MOTOR

STRAP OF TILT BRE AK

BULE

LIGHTI

NG

,FANS

NORM

AL

DIMMER CAN NOT

WORK

COMMEN FAULTY MAINTAIN

FAULTY ANALYSIS

POWER PLUG LOOSE

MAIN BOARD FAULTY

BALLAST FAULTY

FAULTY PHONMENON

WHOLE LIGHT CANN'T WORK

NO LIGHT FROM BULB

SHOW BOARD FAULTY

TRANSFORMER FAULTY

WHETHER THE SIGNAL CABLE GOOD

OR NOT

CAN NOT ADJEST TITL

CAN NOT ADJEST PAN

COMPLETE LIGHT

RESEAT BUT CAN NOT

BE CONTROLLED

MAIN
BOAR

D CAN

NOT

WORK

POWER SWITCH F AULITY

REACH THE LIFESPAN OR BED

QUALITY OF BULB

TRIGGER FAULTY

TEMPERATURE S WITCH B FAULTY

5 METERS CABLE SETS

CAN NOT TURN OFF THE

LIGHT

MAIN BOARD OPTCOOUPLER FAUTLY

FAN ON BOTTOM OF LIGHT FAULTY

BULB LIGHTING AND WHOLE

LIGHT NORMAL BUT FANS

CAN NOT WORK

FAN ON HEAD OF LIGHT FAULTY

REALY OF MAIN BOARD FAULTY

SHOW BOARD FAULTY

MSD 250/2

13. Commen faulty maintain

23

27-00-0010-04

09-00-3151-00

08-05-0400-03

07-07-0250-02

11-10-0010-00

08-07-0020-00

06-03-Z025-00

26-2A-2107XY-00

26-2A-2107DI-00

06-00-B006-00

06-00-B002-00

11-01-0002-00

00-4N25-00

16-00-0008-04

16-00-0008-04

26-2A-2107DI-00

27-04-0010-00

15-00-0001-00

34-01-RD2107_20-00

34-01-RD2107_19-00

34-01-RD2107_18-00

15-00-0073-01

15-00-0076-00

18-06-0009-02

15-00-0076-00

18-06-0009-01

MOTOR FOR TILT FAULTY

447HTD/GT 3M OR RPP3

WEIGHT6mm

420HTD/GT 3M OR RPP3

WEIGHT6mm

42BYGH004-10 MOTOR

NAME

MOTOR1(SHUTTER1)
MOTOR2(SHUTTER2)

MOTOR3(FOCUS)

MOTOR4(PAN)
MOTOR5(TILT)

MOTOR6(GOBO WHEEL)

MOTOR7(GOBO ROTATION)

MOTOR8(ZOOM )

MOTOR9(COLOUR)

MOTOR10(PRISM WHEEL)

MOTOR11(PRISM ROTATION)

MOTOR12(MIX GOBO)

MAIN PCB
2107L PCB
2107S PCB

DISPLAY PCB
IC1 TO IC3 ON MAIN PCB
IC4 TO IC5 ON MAIN PCB
IC6 TO IC8 ON MAIN PCB

IC9 TO IC10 ON MAIN PCB

IC11 ON MAIN PCB
IC12 ON MAIN PCB

CPU ON MAIN PCB

RELAY ON MAIN PCB

PART NO.
15-00-0073-01
15-00-0073-01

15-00-0001-00
15-00-0076-00
15-00-0076-00
15-00-0033-00
15-00-0007-00

15-00-0073-01

15-00-0001-00
15-00-0079-00
15-00-0007-00

15-00-0073-01

26-2A-2107XY-00

26-2A-2108L-00
26-2A-2107S-00

26-2A-2107DI-00

00-7528-00

00-39610-00

00-6219-01
00-3772-00

00-75176-00

00-4N25-00

00-77E58-00

11-01-0002-00

REMARK
42BYGH004-02
42BYGH004-02
42BYGH004-10

23HS0001-02
23HS0001-02

42BYGH026-1

16HY0002
42BYGH004-02
42BYGH004-10

42BYGH026-2

16HY0002
42BYGH004-02

2107XY2.PCB

2107L.PCB
2107S.PCB

2107DI.PCB
D/A CONVERSION CHIP
D/A CONVERSION CHIP

DRIVER CHIP
DRIVER CHIP

DMX CHIP

ELECTRON SWITCH

SOFTWARE CHIP

6P 12VDC 16A/250V

24

MOTOR FOR GOBO WHEEL FAULTY

42BYGH026-1MOTOR

MOTOR OF DAMP POLE

DAMP POLE

MOTOR FOR ROTATION GOGO

FAULTY

16HY0002MOTOR

ROTATION WHEEL FAULTY ROTATION GOBO WHEEL

COLOR WHEEL CAN

NOT CHANGE COLOR

MOTOR FOR COLOR WHEEL

FAULTY

42BYGH026-1MOTOR

CAN NOT ZOOM MOTOR FOR ZOOM FAULTY 42BYGH004-02MOTOR

MOTOR FOR FIXED GOBO

WHEEL FAULTY

42BYGH004-02MOTOR

DAMPER FAULTY DAMP POLE

PRISM WHEEL FAULTY 42BYGH0026-2MOTOR

DAMPER FAULTY DAMP POLE

MOTOR FOR PRISM FAULTY 16HY0002MOTOR

PRSIM WHEEL F AUTLY PRISM WHEEL

DISPLAY

DISPLAYCPU

ROTATION GOBO
WHEEL CAN NOT

CHANGE GOBO

GOBO CAN NOT

ROTATION

FIXED GOBO WHEEL

CAN NOT CHANGE

GOBO

L

BOAR

D

FAULT

Y

S

BOAR

D
CAN
NOT
WOR

K

DISPLAY FAUTLY

HASN'T PRISM EFFECT

PRISM WHEEL CAN
NOT ROTATION

CAN NOT AUTOMATISM

15-00-0033-00

34-01-RD2105_03-00

15-00-0007-00

34-01-RD2107_38-00

15-00-0033-00

15-00-0073-01

15-00-0073-01

34-01-RD2105_03-00

15-00-0079-00

34-01-RD2105_03-00

15-00-0007-00

34-01-RD2105_56-00

26-2A-2107DI-00

00-89S8252-00

14.Component antitheses

25

IC13 TO IC16 ON 2107L PCB
IC17 TO IC20 ON 2107L PCB

CPU ON 2107L PCB
IC21 TO IC23 ON 2107S PCB
IC24 TO IC26 ON 2107S PCB

CPU ON 2107S PCB

CPU ON DISPLAY PCB

TILT HORGE PCB

TILT SENSOR PCB

PAN SENSOR PCB

PAN HORGE PCB

FOCUS HORGE 3C PCB

COLOUR HORGE 3B PCB

ROTATION GOBO WHEEL HORGE 4 PCB

ZOOM HORGE 5 PCB

MIX GOBO HORGE 4B PCB

TRANSMISSION LINE

LIGHT HEAD FAN

BOTTOM FAN

TRANSFORMER(230V)
TRANSFORMER(110V)

BALLAST

CAPACITOR

IGNITOR

THERMOSTAT

LAMP

CONNECTION SET

POWER SWITCH

FILTER

00-7528-01

00-6219-01
00-89S52-00
00-77E58-00

00-6219-01
00-89S52-00

00-89S8252-00

26-2A-YX2105HRT-00

26-2A-YX2105GM-00

26-2A-YX2105GM-00
26-2A-YX2105HRP-00
26-2A-2107HALL3C-00

26-2A-2107HALL3B-00
26-2A-2107HALL4-00

26-2A-HALL5-00

26-2A-2107HALL4B-00

10-01-0010-04
16-00-0008-04

16-00-0008-04
06-00-B002-00
06-00-B006-00

06-03-Z025-00

05-2B-326-251

11-10-0010-00

08-07-0020-00

07-07-0250-02

10-12-0018-00

08-05-0400-03

05-6A-001-251

D/A CONVERSION CHIP

DRIVER CHIP
SOFTWARE CHIP
SOFTWARE CHIP

DRIVER CHIP
SOFTWARE CHIP
SOFTWARE CHIP

2105HRT.PCB

2105GM.PCB
2105GM.PCB

2105HRP.PCB

HALL3.PCB
HALL3.PCB
HALL4.PCB
HALL5.PCB
HALL4.PCB

10P 40cm
80 80 25 DC12V
80 80 25 DC12V

24V/11V 230V~250V
24V/11V 100V~120V

250W 50HZ/60HZ 230V/250V

32UF/250V

400W 220~240V/50~60HZ

110 250V 10A

MSD250/2

7520 15 380V/10A

4P 250V/16A

AC250V 16A 50Hz /60Hz

07-11-0014-00

VS106 CE

32-08-0002-00

LAMP HOLDER

REFLECTOR

COLOR WHEEL

STATHC GOBO WHEEL

SEAT COVER

TOP COVER

LIGHT SHIELD BOARD

ARM

BELT

DMX512SOCKET

55 -1650

34-01-2107_040-BD

RD-2107-040-B

34-05-2107_046-AO

RD-2107-046-A
34-01-250TONG_031-BD
34-06-2107_074-AO

RD-250TONG-031-B

RD-2107-074-A
34-01-2107_059-AO

RD-2107-059-A

34-01-250TONG_048-AO

RD-250TONG-048-A
18-06-0009-01
18-06-0009-02
10-02-0003-00

10-02-0004-00

3-2905 32 26 25

3-2906 32 26 25.5

447HTD/GT 3M/RPP3 Weight 6mm
420HTD/GT 3M/RPP3 Weight 6mm

COMP1

22

COMP2

4

I01

20

I02

8

I11

17

I12

9

PHASE1

16

PHASE2

10

RC1

14

RC2

12

VREF1

15

VREF2

11

OUT 2B5OUT1A

1

OUT1B

21

OUT2A

2

SENSE1

23

SENSE23GND6GND

7

GND18GND

19

VS

24

VSS

13

U3

L6219

R31

20K

R32

20K

R20

1K8

R14

1R8

R21

1K8

R15

1R8

C14

102

C15

102

C7

221

C8

221

1
2
3
4

J1

+30

VCC

COMP1

22

COMP2

4

I01

20

I02

8

I11

17

I12

9

PHASE1

16

PHASE2

10

RC1

14

RC2

12

VREF1

15

VREF2

11

OUT 2B5OUT1A

1

OUT1B

21

OUT2A

2

SENSE1

23

SENSE23GND6GND

7

GND18GND

19

VS

24

VSS

13

U5

L6219

R35

20K

R36

20K

R24

1K8

R18

1R8

R25

1K8

R19

1R8

C18

102

C19

102

C11

221

C12

221

1
2
3
4

J3

+30

VCC

GND

5

Vdd

17

OUT-A

2

lsbDB0

14

RfbA

3

DB1

13

DB2

12

DB3

11

OUT-B

20

DB4

10

DB5

9

RfbB

19

DB6

8

msbDB7

7

AN-GND

1

CS

15

WR

16

Vre fA

4

DACA/B

6

Vre fB

18

U8

AD7528

GND

5

Vdd

17

OUT-A

2

lsbDB0

14

RfbA

3

DB1

13

DB2

12

DB3

11

OUT-B

20

DB4

10

DB5

9

RfbB

19

DB6

8

msbDB7

7

AN-GND

1

CS

15

WR

16

Vre fA

4

DACA/B

6

Vre fB

18

U9

AD7528

COMP1

22

COMP2

4

I01

20

I02

8

I11

17

I12

9

PHASE1

16

PHASE2

10

RC1

14

RC2

12

VREF1

15

VREF2

11

OUT 2B5OUT1A

1

OUT1B

21

OUT2A

2

SENSE1

23

SENSE23GND6GND

7

GND18GND

19

VS

24

VSS

13

U4

L6219

R33

20K

R34

20K

R22

1K8

R16

1R8

R23

1K8

R17

1R8

C16

102

C17

102

C9

221

C10

221

1
2
3
4

J2

+30

VCC

GND

GND

GND

5

Vdd

17

OUT-A

2

lsbDB0

14

RfbA

3

DB1

13

DB2

12

DB3

11

OUT-B

20

DB4

10

DB5

9

RfbB

19

DB6

8

msbDB7

7

AN-GND

1

CS

15

WR

16

Vre fA

4

DACA/B

6

Vre fB

18

U10

AD7528

GND

P31

P31

P31

P34

P33

P32

EA/VP31X119X218RESET9P37/RD17P36/WR

16

P32/INT012P33/INT113P34/T014P35/T1

15

P101P112P123P134P145P156P167P17

8

P0039P0138P0237P0336P0435P0534P0633P0732P2021P2122P2223P2324P2425P2526P2627P27

28

PSEN

29

ALE/P

30

P31/TXD

11

P30/RXD

10

VCC

40

GND

20

U11

W77E58

D7

7

D6

8

D5

9

D4

10

D3

11

D2

12

D1

13

D0

14

A0

15

A1

16

Vre f

1

DA1

2

SIGN1

3

CD1

4

VDD

5

WR

6

/CS

17

VSS

18

CD2

19

SIGN2

20

DA2

21

RST

22

U7

39610

D7

7

D6

8

D5

9

D4

10

D3

11

D2

12

D1

13

D0

14

A0

15

A1

16

Vre f

1

DA1

2

SIGN1

3

CD1

4

VDD

5

WR

6

/CS

17

VSS

18

CD2

19

SIGN2

20

DA2

21

RST

22

U6

39610

Mb2

11

Vbb114VMM2

7

VR1

20

GND

17

Vbb2

9

Phase2

4

E2

10

VR2

3

Mb1

12

Ma1

15

VCC22GND

5

RC

1C121E113

VMM116GND

6

Phase1

19

GND

18

Ma2

8

C2

2

U2

3772

Mb2

11

Vbb114VMM2

7

VR1

20

GND

17

Vbb2

9

Phase2

4

E2

10

VR2

3

Mb1

12

Ma1

15

VCC22GND

5

RC

1C121E113

VMM116GND

6

Phase1

19

GND

18

Ma2

8

C2

2

U1

3772

A0

A1

A0

A1

R28

15K

R26

15K

C5

223

C2

223

C6

223

C3

223

R10

1K

R11

1K

R9

1K

C1

223

R5

0.5

R8

0.5

R6

0.5

R7

0.5

R1

0.5

R4

0.5

R2

0.5

R3

0.5

C4

223

R12

1K

C13

104

R29

470

R30

470

R27

15K

VCC

VCCVCC

VCCVCC

VCC VCC

1

2

3

4

J4 Y

1

2

3

4

J5 X

+30

+30

+30

D7

FR104

D6

FR104

D8

FR104

D4

FR104

D5

FR104

D1

FR104D2FR104

D3

FR104

+30+30 +30

123456789

RP1

33K*8

P02

P03

P04

P05

123

4

J6

OTILT

123

J7

MTILT

123

4

J8

OPAN

123

4

J9

MPAN

R45

4K7

R46

4K7

C25

102

C26

102

C23

102

C24

102

R41

10K

R42

10K

R38

330

VCC

R44

4K7

C22

102

R37

330

R39

10K

R40

10K

C20

102

C21

102

R1RE2DE3D

4

A+

6

B-

7

GND

5

VCC

8

U12

75176

VCC

R49 100

R50 100

IDE

D9 9V

D10

9V

123

J11

DMX

123456789

10

J10

IDC10

RXD

1

2

J16

1

2

J17

P20

P21

P22

P23

P27

P25

A0

A1

P31

P32

P33

P10

P11

P12

P13

WR1

WR2

P16

P17

P20 P21

P22P23P27

P25

P26

1

2

J21

AC11V

E8

2200U/50V

C36

104

C37

104

+12 VCC

C35

104

Vin

GND

Vout

U17 7805

C32

104

C33

104

1

2

J15

AC24V

E3

2200u/50V

E4

2200u/50V

E6

2200u/50V

+30

E5

2200u/50V

U16

4N25

123

J18

RE1A

RE1B

R52

47K

R55

3K3

C29

104

R51

47K

E1

10U/50V

R43

10K

VCC

VCC

X1

X2

C28

C27

Y1

24MHZ

X1

X2

R47

330

C34

104

RE1C

R13

4K7

R56

51

+30

T3

9014

GND

GND

VCC

VCC

WR1

WR2

+30

123

J19

+12

1

J20

FAN

+12

D11

5V1

D12

4148

D13

4148

C30

104

C31

104

P14

P15

P10
P11
P12
P13

P16
P17

P14
P15

P10
P11
P12
P13

P16
P17

P14
P15

P10
P11
P12
P13

P16
P17

P14
P15

P10
P11
P12
P13

P16
P17

P14
P15

P10
P11
P12
P13

P16
P17

P14
P15

P34

P06

P07

P02

P03

P04

P05

P06

P07

P26

E2

2200u/50V

C38

104

C39

104

C40

104

C41

104

C42

104

C43

104

VCC

R57

4K7

VCC

123

J12

MFCS

R48

4K7

C44

102

P24

D15

6A10

D14

6A10

D16

6A10

D17

6A10

D19

5408

D20

5408

D21

5408

D18

5408

P24

E7

2200u/50V

E9

47u/25V

15. MAIN PCB

26

Q1

9012

Q2

9012

Q3

9012

Q4

9012

R1

4K7

R3

4K7

R5

4K7

R7

4K7

VCC

EA/VP31X119X218RESET9RD17WR

16

INT012INT1

13

T014T1

15

P101P112P123P134P145P156P167P17

8

P0039P0138P0237P0336P0435P0534P0633P0732P2021P2122P2223P2324P2425P2526P2627P27

28

PSEN

29

ALE/P

30

TXD

11

RXD

10

U1

89S8252

C1

C2

E2

10U/50V

VCC

X1

X2

R9

10K

K1

FUNCK2DOWNK3UPK4ENTER

P27

P26

P25

P24

P22

P23

P22 P14P23

X1

X2

R2

4K7

R4

4K7

R6

4K7

R8

4K7

DPY

1e11d21c

3

1dp

4

2e

52d62g7

2c

8

2dp

9

2b

102a11

2f

12

1b151a

16

1g171f

18

a

bf

c

g

d

e

dp

a

bf

c

g

d

e

dp

V+

13

V+

14

U2

DR56

DPY

1e11d21c

3

1dp

4

2e

52d62g7

2c

8

2dp

9

2b

102a11

2f

12

1b151a

16

1g171f

18

a

bf

c

g

d

e

dp

a

bf

c

g

d

e

dp

V+

13

V+

14

U3

DR56

P00

P01

P02

P03

P04

P05

P06

P07

P00

P01

P02

P03

P04

P05

P06

P07

P00

P01

P02

P03

P04

P05

P06

P07

P00

P01

P02

P03

P04

P05

P06

P07

P00

P01

P02

P03

P04

P05

P06

P07

P13

P12

CMP

P24

P25

P26

P27

RELY

P12

C3

104

VCC

123456789

10

J1

IDC10

CMP

GND

GND

VCC

VCC

P13

RELY

P14

R11

100

Y1

24MHZ

3

2

1

8 4

U4A

LM358

5

6

7

U4B

LM358

R13

51

R16

10K

R14

470K

R17

510

R15

10K

R12

51K

E1

2u2

C4

104

VCC

MIC1

MIC

GND

VCC

VR1

1M

C5

104

R10

100

P17

16. DISPLAY PCB

27

COMP1

22

COMP2

4

I01

20

I02

8

I11

17

I12

9

PHASE1

16

PHASE2

10

RC1

14

RC2

12

VREF1

15

VREF2

11

OUT 2B

5

OUT1A

1

OUT1B

21

OUT2A

2

SENSE1

23

SENSE23GND6GND

7

GND18GND

19

VS

24

VSS

13

U1

L6219

R33

20K

R34

20K

R17

1K8

R1

1R8

R18

1K8

R2

1R8

C17

102

C18

102

C1

221

C2

221

1
2
3
4

J1

+30

VCC

COMP1

22

COMP2

4

I01

20

I02

8

I11

17

I12

9

PHASE1

16

PHASE2

10

RC1

14

RC2

12

VREF1

15

VREF2

11

OUT 2B

5

OUT1A

1

OUT1B

21

OUT2A

2

SENSE1

23

SENSE23GND6GND

7

GND18GND

19

VS

24

VSS

13

U3

L6219

R37

20K

R38

20K

R21

1K8

R5

1R8

R22

1K8

R6

1R8

C21

102

C22

102

C5

221

C6

221

1
2
3
4

J3

+30

VCC

GND

5

Vdd

17

OUT-A

2

lsbDB0

14

RfbA

3

DB1

13

DB2

12

DB3

11

OUT-B

20

DB4

10

DB5

9

RfbB

19

DB6

8

msbDB7

7

AN-GND

1

CS

15

WR

16

VrefA

4

DACA/B

6

VrefB

18

U8

AD7528

GND

5

Vdd

17

OUT-A

2

lsbDB0

14

RfbA

3

DB1

13

DB2

12

DB3

11

OUT-B

20

DB4

10

DB5

9

RfbB

19

DB6

8

msbDB7

7

AN-GND

1

CS

15

WR

16

VrefA

4

DACA/B

6

VrefB

18

U9

AD7528

COMP1

22

COMP2

4

I01

20

I02

8

I11

17

I12

9

PHASE1

16

PHASE2

10

RC1

14

RC2

12

VREF1

15

VREF2

11

OUT 2B

5

OUT1A

1

OUT1B

21

OUT2A

2

SENSE1

23

SENSE23GND6GND

7

GND18GND

19

VS

24

VSS

13

U2

L6219

R35

20K

R36

20K

R19

1K8

R3

1R8

R20

1K8

R4

1R8

C19

102

C20

102

C3

221

C4

221

1
2
3
4

J2

+30

VCC

GND

GND

COMP1

22

COMP2

4

I01

20

I02

8

I11

17

I12

9

PHASE1

16

PHASE2

10

RC1

14

RC2

12

VREF1

15

VREF2

11

OUT 2B

5

OUT1A

1

OUT1B

21

OUT2A

2

SENSE1

23

SENSE23GND6GND

7

GND18GND

19

VS

24

VSS

13

U4

L6219

R39

20K

R40

20K

R23

1K8

R7

1R8

R24

1K8

R8

1R8

C23

102

C24

102

C7

221

C8

221

1
2
3
4

J4

+30

VCC

EA/VP31X119X218RESET9P37/RD17P36/WR

16

P32/INT012P33/INT113P34/T014P35/T1

15

P101P112P123P134P145P156P167P17

8

P0039P0138P0237P0336P0435P0534P0633P0732P2021P2122P2223P2324P2425P2526P2627P27

28

PSEN

29

ALE/P

30

P31/TXD

11

P30/RXD

10

VCC

40

GND

20

U16

89S52

P00

P01

P02

P03

P04

P05

P06

P07

P00
P01
P02
P03
P04
P05
P06
P07

P00
P01
P02
P03
P04
P05
P06
P07

P20

123456789

RP1

4K7

T1

24MHZ

C31

18P

C32

18P

E1

10U/50V

VCC

P14

VCC

R47

10K

GND

5

Vdd

17

OUT-A

2

lsbDB0

14

RfbA

3

DB1

13

DB2

12

DB3

11

OUT-B

20

DB4

10

DB5

9

RfbB

19

DB6

8

msbDB7

7

AN-GND

1

CS

15

WR

16

VrefA

4

DACA/B

6

VrefB

18

U10

AD7528

GND

P00
P01
P02
P03
P04
P05
P06
P07

GND

5

Vdd

17

OUT-A

2

lsbDB0

14

RfbA

3

DB1

13

DB2

12

DB3

11

OUT-B

20

DB4

10

DB5

9

RfbB

19

DB6

8

msbDB7

7

AN-GND

1

CS

15

WR

16

VrefA

4

DACA/B

6

VrefB

18

U11

AD7528

GND

P00
P01
P02
P03
P04
P05
P06
P07

P11

P12

P13

P14

P20

P21

P22

P23

P24

P25

P26

P11

P11

P11

P11

P27

P21

P15

P12

P13

C42

102

R48

4K7

123

J6

VCC

1

2

J7A

E2

470U/50V

E3

470U/50V

E4

470U/50V

+30

C11

104

C12

104

C13

104

C14

104

C16

104

C27

104

C28

104

C29

104

VCC+30

P27

P26

Focus Hall

123

J8

+30

P22

P23

P24

P25

C34

104

+12

1

2

J9

FAN

+12

From XY Board

1

2

J7B

P00

P01

P02

P03

P04

P05

P06

P07

123

4

J11

MPAN

R12

4K7

R10

4K7

C10

102

C9

102

VCC

Vin

1

GND

2

Vout

3

U21

7805

E5

100U/25V C33

104

+12 VCC

VCC

X1

X2

P32

P33

P36

P32

P33

P36

X1

X2

R9

100

P15

17. DRIVER(L) PCB

28

COMP1

22

COMP2

4

I01

20

I02

8

I11

17

I12

9

PHASE1

16

PHASE2

10

RC1

14

RC2

12

VREF1

15

VREF2

11

OUT 2B

5

OUT1A

1

OUT1B

21

OUT2A

2

SENSE1

23

SENSE23GND6GND

7

GND18GND

19

VS

24

VSS

13

U1

L6219

R33

20K

R34

20K

R17

1K8

R1

1R8

R18

1K8

R2

1R8

C17

102

C18

102

C1

221

C2

221

1
2
3
4

J1

+30

VCC

COMP1

22

COMP2

4

I01

20

I02

8

I11

17

I12

9

PHASE1

16

PHASE2

10

RC1

14

RC2

12

VREF1

15

VREF2

11

OUT 2B

5

OUT1A

1

OUT1B

21

OUT2A

2

SENSE1

23

SENSE23GND6GND

7

GND18GND

19

VS

24

VSS

13

U3

L6219

R37

20K

R38

20K

R21

1K8

R5

1R8

R22

1K8

R6

1R8

C21

102

C22

102

C5

221

C6

221

1
2
3
4

J3

+30

VCC

GND

5

Vdd

17

OUT-A

2

lsbDB0

14

RfbA

3

DB1

13

DB2

12

DB3

11

OUT-B

20

DB4

10

DB5

9

RfbB

19

DB6

8

msbDB7

7

AN-GND

1

CS

15

WR

16

VrefA

4

DACA/B

6

VrefB

18

U8

AD7528

GND

5

Vdd

17

OUT-A

2

lsbDB0

14

RfbA

3

DB1

13

DB2

12

DB3

11

OUT-B

20

DB4

10

DB5

9

RfbB

19

DB6

8

msbDB7

7

AN-GND

1

CS

15

WR

16

VrefA

4

DACA/B

6

VrefB

18

U9

AD7528

COMP1

22

COMP2

4

I01

20

I02

8

I11

17

I12

9

PHASE1

16

PHASE2

10

RC1

14

RC2

12

VREF1

15

VREF2

11

OUT 2B

5

OUT1A

1

OUT1B

21

OUT2A

2

SENSE1

23

SENSE23GND6GND

7

GND18GND

19

VS

24

VSS

13

U2

L6219

R35

20K

R36

20K

R19

1K8

R3

1R8

R20

1K8

R4

1R8

C19

102

C20

102

C3

221

C4

221

1
2
3
4

J2

+30

VCC

GND

GND

EA/VP31X119X218RESET9P37/RD17P36/WR

16

P32/INT012P33/INT113P34/T014P35/T1

15

P101P112P123P134P145P156P167P17

8

P0039P0138P0237P0336P0435P0534P0633P0732P2021P2122P2223P2324P2425P2526P2627P27

28

PSEN

29

ALE/P

30

P31/TXD

11

P30/RXD

10

VCC

40

GND

20

U16

89S52

P00

P01

P02

P03

P04

P05

P06

P07

P00
P01
P02
P03
P04
P05
P06
P07

P00
P01
P02
P03
P04
P05
P06
P07

P20

123456789

RP1

4K7

T1

24MHZ

C31

18P

C32

18P

E1

10U/50V

VCC

P14

VCC

R47

10K

GND

5

Vdd

17

OUT-A

2

lsbDB0

14

RfbA

3

DB1

13

DB2

12

DB3

11

OUT-B

20

DB4

10

DB5

9

RfbB

19

DB6

8

msbDB7

7

AN-GND

1

CS

15

WR

16

VrefA

4

DACA/B

6

VrefB

18

U10

AD7528

GND

P00
P01
P02
P03
P04
P05
P06
P07

P12

P13

P14

P20

P21

P22

P23

P24

P25

P12

P12

P12

P21

P15

P13

E2

470U/50V

E3

470U/50V

+30

C11

104

C12

104

C13

104

C16

104

C27

104

C28

104

VCC+30

123

J8+30

P22

P23

P24

P25

C34

104

+12

1

2

J9

To F AN

+12

From XY Board

1

2

J7

P00

P01

P02

P03

P04

P05

P06

P07

123

4

J11

MPAN

R12

4K7

R10

4K7

C10

102

C9

102

VCC

Vin

1

GND

2

Vout

3

U21

7805

E5

100U/25V C33

104

+12 VCC

VCC

X1

X2

P32

P33

P32

P33

X1

X2

R9

100

P15

18.DRIVER(S) PCB

29