1. INTRODUCTION AND UNPACKING
Thank you for purchasing t he MICROH LED NEO SP OT 60R moving head fixture. For your own
safety and knowledge, please read this manual before installing or operating the device. This
manual covers the important information on installation and applications. Please install and
operate the fixture according to instructions. Meanwhile, please keep this manual for future
reference.
The MICROH LED NEO SPOT 60R model is a moving head light with the latest advancements in
smart, efficient product design. Combined with the advanced technology of today's stage lighting
products, advanced control technology and is very user-friendly; this unit fully complies with CE
standards.
The MICROH LED NEO SPOT 60R has a 60W LED SPOT uses advanced design and
processing technology, with the appearance of high-strength heat resistant engineering plastic
made with the modern streamlined design, to make it look neat and beautiful. This product
contains a white LED light source, eight motors, two gobo wheels, a color wheel, you can change
out many kinds of patterns. This fixture is perfect for use in television, banquet and convention
centres, nightclubs, large-scale performances and other professional venues. Please carefully
unpack the fixture when you receive it and check to see if it was damaged during the
transportation. Please check whether the following items are included inside the box:
Fixture – One Power Cord – One
User Manual – One Omega Bracket – One DMX Cable - One
2. SAFTEY INSTRUCTIONS
This device has been delivered in safe working condition. In order to maintain this condition and
to ensure safe operation, it is absolutely necessary for the user to follow the safety instructions
and warning notes written in this user manual.
If the device has been exposed to temperature changes, do not switch it on immediately. The
arising condensation could damage the device. Leave the device switched off until it has reached
room temperature, and is dry.
This device falls under protection-class I, therefore it is essential that the device be grounded.
The electrical connection must be carried out by a qualified technician.
The device should only be used with rated voltage and frequency. Make sure that the available
voltage is not higher than 120V as stated at the end of this manual.
1
Make sure the power cord is never crimped or damaged in any way, as this could cause shock
and damage. If your power cord is damaged in any way, please purchase a new cable from your
local MICROH dealer. Always disconnect power, when the device is not in use or before cleaning
it. Never pull out the plug by tugging the power cord.
During initial sta rt-up, some smoke or smell may arise. This is a normal process, and does not
necessarily mean that the device is defective. It should decrease gradually. Please do not project
the beam onto combustible substances.
Fixtures cannot be installed on or near combustible substances. Keep more than 3m distance
from wall for proper ventilation and air flow. If your fixture is or has become damaged in any way,
it shall be exclusively replaced or repaired by the manufacturer to avoid any hazard.
3. MOUNTING AND INSTALLATION
Caution: For added protection, mount the fixtures in areas out side walking paths, seating areas,
or in areas were the fixture might be reached by unauthorized personnel. Before mounting the
fixture to any surface, make sure that the installation area can hold a minimum point load of 10
times the device’s weight. Fixture installation must always be secured with a secondary safety
attachment, such as an appropriate safety cable. Never stand directly below the device when
mounting, removing, or servicing the fixture.
Whether installing inverted on a truss, ceiling or set on a flat level surface (see illustration below).
Be sure this fixture is kept at least 3m (3.3 ft.) away from any flammable materials (decoration
etc.). Always use and install the supplied safety cable as a saf ety measure to pr event accidental
damage and/or injury in the event the clamp fails.
Mounting Points: Overhead mounting requires extensive experience, including calculating
working load limits. A knowledge of the installation material being used and periodic safety
inspection of all installation material and the fixture are all imperative and should only be
performed by a qualified technician. Improper installation can result in bodily injury and damage.
Be sure to complete all rigging and installation procedures before connecting the main power
cord to the appropriate wall outlet.
2
Clamp Mounting: The MICROH LED NEO SPOT 60R provides a unique mounting bracket
assembly that integrates a single bracket to be used to mount on a truss or the floor. When
mounting this fixture to truss, be sure to secure an appropriately rated clamp to the included
bracket fitted through the center hole. As an added safety measure, be sure to attach at least one
properly rated safety cable to the fixture.
Regardless of the rigging option you choose for your MICROH LED NEO SPOT 60R, always be
sure to secure your fixture with a safety cable. The fixture provides a built-in rigging point f or a
safety cable on the hanging bracket as illustrated above. Be sure to only use the designated
rigging point for the safety cable and never secure a safety cable to a carrying handle.
4. DMX-512 CONTROL CONNECTIONS
This fixture complies with international USITT DMX standards and can be used with either a 3 pin or 5
pin DMX connector. Plug in the provided 3 pin XLR cable to the female 3-pin XLR output of your
controller and the other side to the male 3-pin XLR inpu t of the MICROH LED NEO SPOT 60R. To
connect the units to DMX, you must daisy chain the fixtures together as referred in the diagram below.
Always end your DMX-51 2 c onnection with a DMX terminator .
For installations where the DMX cable has to run a long distance, or is in an electrically noisy
environment, it is recommended to use a DMX terminator. This helps in preventing corruption of
the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120
Ω resistor connected between pins 2 and 3,which is then plugged into the output XLR socket of
the last fixture in the chain. Please see illustrations below.
3
ADDRESS 001 511
INVERT +X +Y +X -Y -X +Y -X -Y
SLND MASTER SLAVE
DISPLAY ON OFF
SOUND ON OFF
CODE ON OFF
RESET ON OFF
MANUAL ON OFF
EL01 001-255
EL02 001-255
EL03 001-255
EL04 001-255
EL05 001-255
EL06 001-255
EL07 001-255
EL08 001-255
EL09 001-255
EL10 001-255
EL11 001-255
EL12 001-255
CHANN
1
2
3
PIN 3
PIN 2
120Ω
5. SETUP MENU
4
6. 12 DMX CHANNELS
Channel Function Function control Value
OFF 0
DI MMING 1-255
NO EFFECT 0-9
SLOW TO FAST 10-255
Semi-colour, full colour 0-125
WATER COLOUR 126-255
NO EFFECT 0-127
PRISM 128-255
OFF 0
PAN ADHUST (540
°)
1-255
OFF 0
FINE ADJUST 1-255
OFF 0
TILT ADJUST (270
°)
1-255
OFF 0
micro-step adjustment 1-255
OFF 0
SPEED (fast - slow) 1-255
PATTERN 0-79
PATERN SPEED 80-127
PATERN DIRECTION 128-175
JITTER 176-255
NO EFFECT 0-7
FORWARD (fast - slow) 8-127
NO EFFECT 128-135
REVERSE (slow - fast) 136-155
NO EFFECT 0-128
RESET 128-255
Gobo rotation
CH11
Gobos
CH10
Reset
CH12
CH7
TILT
CH8
Dimming (16bit)
CH9
XY Speed
CH4
Prism
CH5
PAN
CH6
PAN (fine)
CH1
Dimmer
CH2
Strobe
CH3
Color Palette
7. TECHNICAL SPECIFICATIONS
Power: 110~240V 80W
Frequency: 50/60Hz
LED’s: 1 x 60W 4-in-1 LED
Fuse: 5A250V
Fixture Dimension: 26.7 x 15.24 x 33cm (10.5’’x6”x13”)
Packing Dimensions: 31 x 20 x 41cm (12.2”x7.9”x16.14”)
Net Weight: 6Kg (13.2Lbs)
Gross Weight: 7Kg (15.4Lbs)
5
8. MAINTENANCE AND CLEANING
The following points have to be considered during the inspection:
1) All screws for installing the device or parts of t he device must be tightly connected, and m ust
not be corroded.
2) There must not be any deformations on the housing, colour lenses, fixations or installation
spots (ceiling, suspension, trussing).
3) Mechanically moved parts must not show any traces of wearing and must not rotate with
unbalances.
4）The electric power supply cables must not show any damage, material fatigue or sediments.
Further instructions depending on the installation spot and usage must be handled by a skilled
installer or technician. Any safety issues must be resolved.
In order to keep the fixture in good condition and extend the life, we suggest regular cleaning to
the fixture.
1) Clean the inside and outside lens each week to avoid the lig ht output from darkening due to
accumulation of dust, dirt, etc.
2) Clean the fan each week.
3) A detailed electrical check by approved technician every thr ee months is ad vised. Ensure t he
circuit contacts are in good condition.
We recommend a frequent cleaning of the device. Please use a moist, lint- free c loth. Never use
alcohol or solvents.
There are no serviceable parts inside the device. Please refer to the instructions under
“Installation instructions”.
Should you need any spare parts, please order genuine MICROH parts from your local dealer.
IF YOU SHOULD EXPERIENCE ANY PROBLEMS OR ISSUES PLEASE CONTACT MICRO H
PROFESSIONAL PRODUCTS BY EMAI L AT info@microhdj.com
In the event that your unit is defective in any way, please contact your local dealer to
obtain an RA number for service repair.
DISCLAIMER – MICROH believes that the information contained within this user manual is
accurate. However, MICROH is not responsible for any error or addendums to this manual.
If you have any comments or general suggestions on how this manual can be improved
please contact info@microhdj.com
. Thank you.
6
Loading...