User Manual
KEEP THIS MANUAL FOR FUTURE NEEDS
tc
150°C
LE D
0.2m
ta
40°C
BEAM710
LED HALO
.01.
If the device has been exposed to temperature changes due to environmental changes,
do not switch it on immediately. The arising condensation could damage the device.
Leave the device switched off until it has reached room temperature.
This device falls under protection-class I. Therefore it is essential that the device be
ear thed.
The electric connection must carr y out by qualified person.
The device shall only be used with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this would
be the case, replacement of the cable must be done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning it.
Only handle the power cord by the plug. Never pull out the plug by tugging the power
cord.
During initial start-up some smoke or smell may arise. This is a normal process and
does not necessarily mean that the device is defective, it should decrease gradually.
Please don't project the beam onto combustible substances.
Fixtures cannot be installed on combustible substances, keep more than 50cm
distance with wall for smooth air flow, so there should be no shelter for fans and
ventilation for heat radiation.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively
replaced by the manufacturer or his ser vice agent or a similar qualified person in order
to avoid a hazard.
This device has left the factory in perfect condition. In order to maintain this
condition and to ensure a safe operation, it is absolutely necessar y for the user to
follow the safety instructions and warning notes written in this user manual.
CA UT ION
Becareful with your oper ations.With a dangerous vol tage you cansuffer a
dangerous electric shock when touching wires!
IMPORTANT
Damages caused by the disregard of this user manual are not subject to warranty.
The dealer will not accept l iability for any resulting defects or problems.
SAFETY INSTRUCTIONS
1
Thank you for choosing MICROH’s LED HALO BEAM710. For your own safety, please
read this manual before installing the device. This manual covers the important
information on installation and applications. Please install and operate the fixture
with following instructions. Meanwhile, please keep this manual well for future
needs.
MICROH’s LED HALO BEAM710 is made of a new type of high temperature strength
of engineering plastics and cast aluminum casing with nice outlook . The fixture is
designed and manufactured strictly following CE standards, complying with
international standard DMX512 protocol. It’s available independently controlled
and linkable with each other for operation. And it is applicable for large-scale live
performances, theater, studio, nightclubs and discos.
LED HALO BEAM710 adopts 7PCS OSRAM LE RTDUW S2W 4-IN-1 15W LEDs which
features high brightness and stability. Please carefully unpack it when you receive
the fixture and check whether it is damaged during the transportation. And please
check whether the following items are included inside the box:
.02.
UNPACKING
2
⑥
①
②
④
⑤
Moving Head
Signal Cable
Power Cable
Hanging Kit
Safety Cable
User Manual
1PC
1PC
1PC
1PC
1PC
1PC
①
②
③
④
⑤
⑥
③
Euro Standard
UK Standard
USA Standard
OPTIONAL
.03.
Specifications
Input Voltage:
LED Quantities:
Control Signal:
Control Channel:
Power Consumption:
Dimensions:
Packing Dimensions:
Net Weight:
Gross Weight:
Features
AC90-260V 50/60Hz
7PCS OSRAM LE RTDUW S2W 4-IN-1 15W LEDs
DMX512, master-slave and sound activated or auto operation
15 DMX Channels USITT DMX-512
120W
152(D)*265(W)*315(H)mm
200(D)*320(W)*370(H)mm
5kg
6kg
FEATURES & SPECIFICATIONS
3
• 7PCS OSRAM LE RTDUW S2W 4-IN-1 15W LEDs.
• 50,000 hours life span for LEDs and low power consumption
• Intelligent temperature sensor for LEDs(over heat protection)
• High efficiency 8 degree optic lens
• Color range with 16.7 millions additive RGBW colors
• High light output as 684LUX@ 7M at full
• 0-100% smooth linear dimmer with flicker free
• 20t/s strobe effect with variable speed
• Pre-programmed random strobe and pulse effects
• 15 DMX Channels USITT DMX-512
• Built-in programs with macro effects
• DMX512, master-slave and sound activated controllable or auto operation
• High definition blue TFT LCD display
• Quiet, smooth and fast PAN/TILT movement
• Low noise and efficient FAN cooling system
• 540° PAN and 270° TILT movement
• Scan position memor y, auto reposition af ter unexpected movement
• Compact size with only 4.9KG body and 304mm in height
• IEC power connector IN
• 45°C max ambient temperature
• IP20 protection rating
• 3-Pin XLR DMX IN/OUT
8°Beam Angle LUX 0.0929=FC×
Photometric Beam Angle Data
1379 / 14840 218 / 2350 41 /446
1m (3.3ft)
3m (9.8ft) 5m (16.4ft)0m (0ft)
(FC/LUX)
1970 / 21200 339 / 3652 68 / 732
2408 / 25920
2640 / 28420
391 / 4210
576 / 6204
76 / 823
114 / 1232
6677 / 71870 1147 / 12350 226 / 2431
R
G
B
W
RGBW
8°
80 / 858
129 / 1386
148 / 1595
215 / 2310
434 / 4670
7m (23.0ft)
.04.
PHOTOMETRIC DATA
4
265152
275
315
163
.05.
· The moving head is for beam effect for on-site decoration purpose.
· Don’t turn on the fixture if it’s been through severe temperature difference like
af ter transportation because it might damage the light due to the environment
changes. So make sure to operate the fixture until it is in normal temperature.
· This light should be keep away from strong shaking during any transportation or
movement.
· Don’t pull up the light by only the head, or it might cause damages to the
mechanical parts.
· Don’t expose the fixture in overheat, moisture or environment with too much dust
when installing it. And don’t lay any power cables on the floor. Or it might cause
electronic shock to the people.
· Make sure the installation place is in good safety condition before installing the
fixture.
· Make sure to put the safety chain and check whether the screws are screwed
properly when installing the fixture.
· Make sure the lens are in good condition. It’s recommended to replace the units if
there are any damages or severe scratch.
· Make sure the fixture is operated by qualified personnel who knows the fixture
before using.
· Keep the original packages if any second shipment is needed.
· Don’t try to change the fixtures without any instruction by the manufacturer or
the appointed repairing agencies.
· It is not in warranty range if there are any malfunctions from not following the
user manual to operate or any illegal operation, like shock short circuit, electronic
shock, lamp broke, etc.
OPERATION INSTRUCTIONS
5
Cautions: For added protection mount the fixtures in areas outside walking paths,
seating areas, or in areas were the fixture might be reached by unauthorized
personnel.
Before mounting the fixture to any sur face, make sure that the installation area can
hold a minimum point load of 10 times the device’s weight.
Fixture installation must always be secured with a secondary safety attachment, such
as an appropriate safety cable.
INSTALLATIONS
6
.06.
①
②
③
Never stand directly below the device when mounting, removing, or servicing the
fixture.
from a ceiling, or set on a flat level surface (see illustration below). Be sure this fixture
is kept at least 0.5m (1.5 ft) away from any flammable materials (decoration etc.).
Always use and install the supplied safety cable as a safety measure to prevent
accidental damage and/or injur y in the event the clamp fails.
Mounting points: Overhead mounting requires extensive experience, including
amongst others calculating working load limits, a fine knowledge of the installation
material being used, and periodic safety inspection of all installation material and the
fixture. If you lack these qualifications, do not attempt the installation yourself.
Improper installation can result in bodily injur y.
Be sure to complete all rigging and installation procedures before connecting the
main power cord to the appropriate wall outlet.
Clamp Mounting: The LED HALO BEAM710 provides a unique mounting bracket
assembly that integrates the bottom of the base, and the safety cable rigging point in
one unit (see the illustration below). When mounting this fixture to truss be sure to
secure an appropriately rated clamp to the included omega bracket using a M10
screw fitted through the center hole of the “omega bracket”. As an added safety
measure be sure to attached at least one properly rated safety cable to the fixture
using on of the safety cable rigging point integrated in the base assembly.
④
① Omeg a Brack et
② Sate ty Clam p
③ Safe ty Cabl e
④ 1/4 Turn Qui ck-Lo ck Fast eners
Turn around Turn around
.07.
Regardless of the rigging option you choose for your , always be
sure to secure your fixture with a safety cable. The fixture provides a built-in rigging
point for a safety cable on the hanging bracket as illustrated above. Be sure to only
use the designated rigging point for the safety cable and never secure a safety cable
to a carrying handle.
LED HALO BEAM710
Connect the provided XLR cable to the female 3-pin XLR output of your controller and
the other side to the male 3-pin XLR input of the moving head. You can chain multiple
Moving head together through serial linking. The cable needed should be two core,
screened cable with XLR input and output connectors. Please refer to the diagram
below.
DMX-512 connection with DMX terminator
DMX-512 CONTROL CONNECTIONS
7
POWER IN
DMX IN
Power Switc h
Fuse
POWER IN
POWER OUT
DMX IN
DMX OUT
.08.
DMX Output
3-Pin XLR Soc ket
DMX Input
3-Pin XLR Soc ket
1:Ground
2:Data(-)
3:Data(+)
1 2
3
12
3
1
2
3
1
2
3
COMMON
DMX+
DMX-
DMX512 IN
3-PIN XLR
DMX512 OUT
3-PIN XLR
2 1
For installations where the DMX cable has to run a long
distance or is in an electrically noisy environment, such as
in a discotheque, it is recommended to use a DMX
terminator. This helps in preventing corruption of the
digital control signal by electrical noise. The DMX
terminator is simply an XLR plug with a 120 Ω resistor
connected between pins 2 and 3,which is then plugged
into the output XLR socket of the last fixture in the chain.
Please see illustrations below.
1
2
3
PIN3
PIN2
120 Ω
MENU OPERATIONS
8
DMX-ADR
ADJ-R
001 512
ADJ-G
ADJ-B
ADJ-W
000 255
000 255
000 255
000 255
PROGRAM
001 013
ADJ-S
000
016
TEST-MOD
AUTO-MD
Sound-MD
REST
ESC
DOWN
ENTER
LCD DISPLAY
UP
.09.
DMX CHANNELS
9
PAN Movement
Fine control of Pan movement
Tilt Movement
Fine control of Tilt movement
0-100% Linear dimmer from dark to bright
Strobe effect from slow to fast
0-100% red dimmer from dark to bright
0-100% green dimmer from dark to bright
0-100% blue dimmer from dark to bright
0-100% white dimmer from dark to bright
Colors changing effect
CH1-CH11 activated
Colors jumping
Colors fading
Colors mixing
Sound control
Speed of macros
Speed control of PAN/TILT (fast to slow)
CH1-CH14 activated
Reset after 3 seconds
Descrip tionChannel Function Value
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-010
011-120
121-180
181-244
245-255
0-255
0-255
0-244
245-255
Pan
Pan Fine
Tilt
Tilt Fine
Dimmer
Strobe
Red
Green
Blue
White
Colors
Macros
Speed
Speed
Reset
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
.10.
The following points have to be considered during the inspection:
1) All screws for installing the devices or parts of the device have to be tightly
connected and must not be corroded.
2) There must not be any deformations on the housing, color lenses, fixations and
installation spots (ceiling, suspension, trussing).
3) Mechanically moved parts must not show any traces of wearing and must not
rotate with unbalances.
4) The electric power supply cables must not show any damage, material fatigue or
sediments.
Fur ther instructions depending on the installation spot and usage have to be
adhered by a skilled installer and any safety problems have to be removed.
In order to make the lights in good condition and extend the life time, we suggest a
regular cleaning to the lights.
1) Clean the inside and outside lens each week to avoid the weakneness of the lights
due to accumulation of dust.
2) Clean the fan each week .
3) A detailed electric check by approved electrical engineer each three month, make
sure that the circuit contacts are in good condition, prevent the poor contact of
circuit from overheating.
We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth.
Never use alcohol or solvents.
There are no serviceable parts inside the device. Please refer to the instructions
under “Installation instructions”.
Should you need any spare par ts, please order genuine parts from your local dealer.
MAINTENANCE AND CLEANING
10
Disconnect from mains before starting maintenance operation.
CA UT ION
Loading...