MicroDigial MDC-4, MDC-8, MDC-6 TDN, MDC-7 User Manual

Download

Supreme Resolution

Day & Night Color Camera

www.microdigital.co.kr

USER MANUAL

2 MICRODIGITAL

USER INFORMATION

CAUTION

RISK OF ELECTRIC SHOCK, DO NOT OPEN NO USER-SERVICEABLE PARTS INSIDE.

REFER FOR SERVICING TO QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSISTING OF A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.

THIS EXCLAMATION POINT SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.

This marking on the product, accessories or literature indicates that the product and its electronic accessories should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

CAUTION

MICRODIGITAL 3

• This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio com-

munications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required

to correct the interference at his own expense.

◆

Information

USER INFORMATION

• Any changes or modifications in construction of this device which are

not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

• This installation should be made by a qualified service person and

should abide to all local codes.

◆

Warning

4 MICRODIGITAL

PRECAUTIONS

• Do not install the camera in extreme temperature conditions.

Only use the camera under conditions where temperatures are between -10°C and +50°C. Be especially careful to provide ventilation when operating under high temperatures.

• Do not install or use the camera in an environment where the humidity is high.

It can cause the image quality to be poor.

• Do not install the camera

under unstable lighting conditions.

Severe lighting change or flicker can cause the camera to work improperly.

• Do not touch the front lens of

the camera.

This is one of the most important parts of the camera. Be careful not to leave fingerprints on the lens cover.

• Do not drop the camera

and protect it from physical shocks.

It can cause malfunctions to occur.

• Never keep the camera

pointed directly at strong light.

It can damage the CCD.

• Do not expose the camera to

rain or spill beverage on it.

If it gets wet, wipe it dry immediately. Liquids

can contain minerals that corrode the electronic components.

• Do not expose the camera to

radioactivity.

If exposed to radioactivity the CCD will fail.

USER INFORMATION

MICRODIGITAL 5

Ignoring this information may result in material loss and/or serious personal injuries including death.

Indicates “Never Allowed.”

Ignoring this information may result in material loss and/or a slight injuries.

Indicates “No Disassembling.”

USER INFORMATION

NOTE

• Exposure to a spotlight or an object emitting strong light may cause smear or blooming.

•

Ensure that the power source complies with normal specifications before supplying it to

the camera.

• Power supply.(Adaptor : DC12V)

- To avoid fire or shock hazard, must use a UL listed power supply.

• Monitor Impedance.

- Set the impedance switch to 75ohm standard position.

- When monitor is set to high impedance mode, the picture becomes blurred. In this case, just check the position of the monitor impedance switch.

6 MICRODIGITAL

• DESCRIPTION 8 - 10

• SPECIFICATION 11 - 12

• FEATURES 13 - 14

• COMPONENTS 15 - 29

▪ BOX CAMERA ▪ BULLET CAMERA ▪ DOME CAMERA ▪ VANDAL CAMERA

15 - 17 18 - 24 25 - 27 28 - 29

• INSTALLATION 30 - 35

▪ BOX CAMERA ▪ BULLET CAMERA ▪ DOME CAMERA ▪ VANDAL CAMERA

30 - 31

32 33

34 - 35

• OSD OPERATION 36 - 42

▪ BOX CAMERA ▪ BULLET CAMERA ▪ DOME CAMERA ▪ VANDAL CAMERA

36 - 37 37 - 39

40 41

• INSTRUCTIONS 43

• OSD STRUCTURE 44

CONTENTS

MICRODIGITAL 7

CONTENTS

• LENS

•

EXPOSURE 46 - 48

▪ SHUTTER ▪ AGC ▪ SENS-UP ▪ BLC ▪ D-WDR ▪ RETURN

46 46 47 47 48 48

•

WHITE BALANCE 49 - 50

•

DAY & NIGHT

51 - 52

•

3D DNR

•

SPECIAL

54 - 59

▪ CAM TITLE ▪ D-EFFECT ▪ RS-485 ▪ MOTION ▪ PRIVACY ▪ SYNC ▪ LANGUAGE ▪ DEFECT

54 55 56 56 58 59 59 59

•

ADJUST

•

RESET

• OSD STRUCTURE

-MAIN MENU

8 MICRODIGITAL

Before operating the camera, confirm the camera model and proper input power voltage. In order to help you understand this manual thoroughly, we’ll introduce our model description.

◆ MODEL DESCRIPTION

MDC - H8220 TDN - 30 HU

H 8 2 2 0

Built in Heater / UTC

Number of IR-LED

Day / Night Filter mechanism

Power source Number of Pixels B/W(1) / Color(2)

Case type

Model type

• EX)

DESCRIPTION

MICRODIGITAL 9

DESCRIPTION

CASE TYPE MODEL

TYPE

COLOR PIXEL POWER D/N

LENS

IR/HEATER / CASE

1: MINI BULLET

2: MODULE

3: MINI SQUARE

4: BOX

5: ZOOM

6: IR BULLET

7: INDOOR

DOME

8: OUTDOOR

DOME

(VANDAL)

9: MINI VANDAL

i : IP

H : HD

1: B/W

2: COLOR

1: 270K

2: 520K

6: 1.3M

9: 2.1M

0: DC 12V

1: DUAL

VOLTAGE

(DC 12V/

AC24V)

2: AC230V

CTD

CDN

FDN

TDN

VTD

VDN

WDN

F(E)

V(E)

IR : No. of

IR-LED

H: With Heater

U : UTC

CONTROL

MS : SUFACE

MOUNT TYPE

MF : FLUSH

MOUNT TYPE

IR & HEATER (MDC-6xxx, 7xxx, 8xxx MODEL)

-H -U

Built-in Heater UTC Remote Control

-30 -30H

Built-in IR LED

and CDS Sensor

Built-in IR LED

and CDS Sensor With Heater

Heater

LED

10 MICRODIGITAL

PRECAUTIONS

DAY / NIGHT FILTER & MECHANISM

CDN

DIGITAL DAY / NIGHT

FDN

DIGITAL DAY / NIGHT

VDN

DIGITAL DAY / NIGHT

TDN

TRUE DAY / NIGHT (ICR-IR Cut Filter Removable)

POWER SOURCE

MDC-xxx0

- DC 12V

MDC-xxx1

- AC 24V / DC 12V, Dual-Power

MDC-xxx2

- AC 230V

DAY / NIGHT

LENS

Fixed

DC Auto Iris Lens

AC 230V

AC 24V DC 12V

DC 12V

DAY / NIGHT

DC Auto Iris Lens

FILTER CHANGE

LENS

VARIFOCALVARIFOCAL

LENS

VARIFOCALVARIFOCAL

DESCRIPTION

MICRODIGITAL 11

Signal System

NTSC PAL

Scanning Frequency 15,734KHz(H), 59.94Hz(V) 15,625KHz(H), 50.00Hz(V)

Image Sensor 1/3” Interline Transfer Type High Sensitivity Color CCD

Sync. System INT / LL

Total Pixels Number 1020(H) X 508(V), 520K pixels 1020(H) X 596(V), 610K pixels

Effective Pixels Number 976(H) x 494(V), 480K pixels 976(H) x 582(V), 570K pixels

Horizontal Resolution Color 700 TV Lines

Video Output Level 1.0Vp-p, 75ohm (Video 0. 714Vp-p Sync. 0.286Vp-p)

S/N Ratio 52 dB (AGC OFF, Weight On)

Dynamic Range 52dB(*128)

DAY / NIGHT COLOR / AUTO / BW / EXTERNAL

Sens Up AUTO / OFF

3 DNR ON / OFF (1~128 Level Selectable)

D-WDR INDOOR / OUTDOOR / OFF

AGC LOW / MIDDLE / HIGH

BLC BLC / HSBLC

AWB ATW / AWB / INDOOR / OUTDOOR / MANUAL / AWC

Mirror OFF / MIRROR / V-FLIP / ROTATE

Privacy Function ON / OFF (8 Zone)

Motion Detection ON / OFF (4 Zone Selectable)

Freeze ON / OFF

Sharpness 0~31 (Level Selectable)

Digital Zoom On(*32) / OFF

MONITOR LCD / CRT / USER

DEFECT SENSE-UP / DIFFERENCE / START

Electronic Shutter 1/60sec ~ 1/100,000sec 1/50sec ~ 1/100,000sec

OSD Built-in

Operating Temperature (-)30°C ~ (+)50°C, (-)40°C ~ (+)50°C (Built-In Heater Model)

Operating Humidity 95% RH max

Power Voltage DC12V ± 10%

SPECIFICATION

12 MICRODIGITAL

MODEL

TYPE LENS

MDC-4xxx

CDN C / CS MOUNT

TDN C / CS MOUNT (ICR-IR Cut Filter Removable Mechanism)

MDC-6xxx

TDN

35H, 45, 40H, 32 Filter Changeable Vari-Focal 6.0~50.0mm DC Auto Iris Lens

20, 20H, 36H, 48

24H, 42

Filter Changeable Vari-Focal 3.5~16.0mm DC Auto Iris Lens

32U, 40HU Filter Changeable Vari-Focal 6.0~50.0mm 2 Motor Drive Lens

24HU, 42U Filter Changeable Vari-Focal 3.5~16.0mm 2 Motor Drive Lens

MDC-7xxx

FDN Built-In Fixed 3.6mm Board Lens

VDN Vari-Focal 3.5~16.0mm DC Auto Iris Lens

TDN Filter Changeable Vari-Focal 3.5~16.0mm DC Auto Iris Lens

MDC-8xxx

VDN Vari-Focal 3.5~16.0mm DC Auto Iris Lens

TDN Filter Changeable Vari-Focal 3.5~16.0mm DC Auto Iris Lens

MODEL

TYPE Min. ILLUMINATION

MDC-4xxx

CDN 0.15 (Color) / 0.03 (BW) / 0.00001 / Lux(Sens-up x 256)

TDN

0.15 (Color) / 0.01 (BW) / 0.00001 / Lux(Sens-up x 256) (ICR-IR Cut Filter Removable Mechanism)

MDC-6xxx

TDN

0.25 (Color) / 0.01 (BW) / 0.00001 Lux / Lux at F1.2 (Sens-up x 256) 0 Lux at IR LEDs On (ICR-IR Cut Filter Removable Mechanism)

MDC-7xxx

FDN 0.25 (Color) / 0.06 (BW) / 0.00001 / Lux at F1.2 (Sens-up x 256)

VDN 0.15 (Color) / 0.03 (BW) / 0.00001 / Lux at F1.2 (Sens-up x 256)

TDN

0.25 (Color) / 0.01 (BW) / 0.00001 / Lux at F1.2 (Sens-up x

256) (ICR-IR Cut Filter Removable Mechanism)

MDC-8xxx

VDN 0.15 (Color) / 0.03 (BW) / 0.00001 / Lux at F1.2(Sens-up x 256)

TDN

0.25 (Color) / 0.01 (BW) / 0.00001 / Lux at F1.2(Sens-up x 256) (ICR-IR Cut Filter Removable Mechanism)

LENS

Min. ILLUMINATION

▶Specifications are subject to change without prior notice due to improvement

SPECIFICATION

MICRODIGITAL 13

FEATURES

1/3” Interline Transfer Type High Sensitivity Color CCD

700TV Lines

The combination of a 1/3” Interline Transfer Type High Sensitivity Color CCD and DNR DSP provides an excellent resolution of 700 TV lines.

Min. Illumination

With an incredibly Minimum Illuminatio of Amazing 0.0001Lux can Capture Good Images Even in Extremely Low Light Conditions and Related Noises are Significantly Reduced by the Ultra Advanced DNR(Digital Noise Reduction) Technology.

D-WDR (Digital Wide Dynamic Range)

D-WDR is a powerful and ultra advanced technology that captures clear and superior high Resolution pictures even where images appear dark because there is a strong back light present.

High Light Compensation (HLC) Function

High Light Compensation Function is Especially Effective to Read the Number Plate of the Vehicles in the Street or Parking Lot at Night Time. Especially

Users Can Adjust and Select the Special Required Area to Observe the Target

Object Under the Strong Spots of Light Exist.

3D Filtering Method of Newly Advanced DNR Functionn

Newly developed 3D filtering enhances Digital Noise reduction at low light levels. 3D Filtering of the Video Signal Optimized the Signal to Noise ratio, giving vastly improved low light visibility and a powerful Sens-Up function (up to 258 times magnification).

DAY / NIGHT

The camera identifies whether it is day or night and automatically switches to the appropriate mode, depending on its environment. By day, the camera switches to color mode in order to maintain optimal color. At night, it switches to B/W mode so as to obtain better picture definition.

DPC (Dead Pixel Compensation [Max 512points])

When the camera becomes hot after operating a couple of days, white spots are shown on the screen especially at low light condition and they are recorded together with normal image. By using thise function, white spots are removed and you can get clean images.

700 TV LINE

DAY / NIGHT

3DNR

1/3” IT

CCD

HLC

14 MICRODIGITAL

DIGITAL ZOOM

Digital zoom available, OFF(x1) / ON(x2~x32) can be selected

IR SMART

It enables users to distinguish the indistinguishable images saturated by IR LED.

Additional Functions

1. OSD - ON Screen Display menu with multi-Language support.

2. FreeArea Selectable function of BLC and MOTION DETECTION

3. Privacy Color Masking for 8 Area selection

4. Max 70% of Disk Saving Effect with Super DNR

5. Negative image Function

Weather proof IP66

MDC-6xxx , MDC-8xxx MODEL

External Focus & Focal Length Adjustment

77Ø, 88Ø Series (MDC-6220VTD-35H, 36H, 45, 48)

Dual(Surface / Flush) Mount Type Vandal Proof Dome Camera

MDC-8xxx MODEL

1. The unit is installed by two types of installation with flush or surface mount. When the camera is installed with flush mount, the unit can be installed into an existing two-gang junction box.

2. Surface or Flush Mounting using the supplied surface mount bracket.

C / CS Mount Lens Adjustable

MDC-4xxx MODEL

UTC Remote Controller

- Long distance controller.

- Menu can be adjusted without opening the camera case.

- It is of conveniently portable size.

IP66

SMART

Vandal Proof

OSD

FEATURES

MICRODIGITAL 15

COMPONENTS

1. Camera

2. Manual

Width Height depth

64 58 90

pypzGqhjr

}pklvGv|{

XY}Gkj

kv~u

slm{

ypno{

wv~ly

tlu|

mUn

pypzGqhjr

}pklvGv|{

kv~u

slm{

ypno{

wv~ly

tlu|

mUn

myllG}vs{hnl

MICRODIGITAL

16 MICRODIGITAL

Over view

MDC-4220CDN / TDN

COMPONENTS

1 Lens protection cap

Cover the lens when not in use.

2 CS-mount lens adaptor

Attach the CS-mount lens here, and if you want to use C-mount lens, also please attach C-ring to the CS-mount and then also

3 Back focus clamp screw

Loosen the clamp screw with a L-Wrench before adjusting the Back Focal length.

4 Camera mounting screw hole.

Back focus clamp screw & Hole

Lens protection cap

CS-MOUNT Lens adaptor

Camera mounting screw hole.

MICRODIGITAL 17

COMPONENTS

Rear view

Specifications and Designs are subject to change without prior notice due to improvement

1 Auto iris lens connector

Connection terminal for an auto iris lens.

2 Video output terminal

Sends video signals and connects to the video input terminal of the monitor.

3 Power lamp

Lights up when the correct power is supplied to the camera.

4 OSD button 5 Power input terminal : Low voltage power connection. 6 AC Power Cord : Accept AC90~240V-50Hz/60Hz

MDC-4xx0/ 4xx1

MDC-4xx2

AC24V / DC12V AC230V

2 2

3 3

pypzGqhjr

}pklvGv|{

XY}Gkj

kv~u

slm{

ypno{

wv~ly

tlu|

mUn

pypzGqhjr

}pklvGv|{

kv~u

slm{

ypno{

wv~ly

tlu|

mUn

myllG}vs{hnl

18 MICRODIGITAL

1. Varifocal IR Bullet Camera

2. Cable for Extra Video

3. L-WRENCH

4. Screw for Installation

5. Manual

COMPONENTS

MICRODIGITAL 19

VBS-EXTRA

1 Lens

2 IR-LED / Heater (Option)

3 Zoom / Focus Lever

4 OSD Joystick (Option)

5 Cable Management Bracket

6 VBS-Extra for connecting to LCD (Option)

COMPONENTS

MDC-6220TDN-20 & 20H (65Ø)/24H(U)42(U)(75Ø)

20 MICRODIGITAL

MDC-6220

20 20H

24H(U)

42(U)

Dimension

Diameter 65ø 75ø

Width 81 89

Length 196 217

IR LED

& Heater

20pcs

IR LED

20pcs

IR-LED,

4pcs Heater

20pcs

IR-LED,

4pcs Heater

42pcs

IR LED

Power Consumption

Normal 140mA

IR LED ON 320mA 350mA 500mA

Heater ON X 460mA 480mA X

Dimension

▶Specifications and Designs are subject to change without prior notice due to improvement

COMPONENTS

MICRODIGITAL 21

1 Lens

2 IR-LED / Heater (Option)

3 Zoom / Focus Lever

4 OSD Joystick (Option)

5 Cable Management Bracket

6 VBS-Extra for connecting to LCD (Option)

VBS-EXTRA

COMPONENTS

MDC-6220TDN-32 & 40H (90Ø)

22 MICRODIGITAL

MDC-6220 32(U) 40H(U)

Dimension

Diameter 90ø

Width 114

Length 205

IR LED &

Heater

32pcs Giant

IR-LED

16pcs Giant / 24pcs IR-LED,

4pcs Heaters

Power Consumption

Normal 140mA

IR LED ON 570mA 440mA

Heater ON X 570mA

Dimension

▶Specifications and Designs are subject to change without prior notice due to improvement

COMPONENTS

MICRODIGITAL 23

1 Lens

2 IR-LED / Heater (Option)

3 Zoom / Focus Ring

4 OSD Joystick

5 Cable Management Bracket

FOCUS

ZOOM

COMPONENTS

MDC-6220TDN-35H & 45(76Ø) / 36H & 48 (95Ø)

24 MICRODIGITAL

MDC-6220VTD 35H 45 36H 48

Dimension

Diameter 95ø 76ø

Width 119 92.3

Length 206 170

IR LED & Heater

12pcs Giant

/ 23pcs

IR-LED &

4pcs Heater

12pcs Giant

& 33pcs

IR-LED

36pcs

IR-LED &

3pcs Heater

48pcs

IR-LED

Power Consumption

Normal 140mA

IR LED ON 520mA 620mA 480mA 580mA

Heater ON 660mA X 660mA X

Dimension

▶Specifications and Designs are subject to change without prior notice due to improvement

COMPONENTS

MICRODIGITAL 25

Surface Mount Bracket

Tapping Screw

Surface Mount Screw

Service Monitor Cable

L-Wrench

andal Resistant Dome Camera

(Surface T

ype)

Vandal Resistant Dome Camera

(Surface Type)

Vandal Resistant Dome Camera

(Flush Type)

Manual

Mounting Screw

COMPONENTS

26 MICRODIGITAL

VBS-EXTRA

1 Lens 2 3 Axis bracket

· Adjust the pan and tilt to give the correct angle of view. 3 OSD Joystick / Board 4 VBS-Extra for connecting to LCD

· Please use the supplied wire when connecting to an external monitor. 5 IR LED

1 1

MDC-7220FDN (68Ø) / 7220VDN, TDN, TDN-30 (100Ø)

MDC-7220FDN

MDC-7220TDN-30

MDC-7220VDN / TDN

COMPONENTS

MICRODIGITAL 27

MDC-7220 FDN VDN TDN VTD-30

Dimension

Diameter 68ø 100ø

Width 90 135

Height 62 100

IR LED

X X X

30pcs

IR-LED

Power Consumption

Normal 150mA 170mA

IR LED ON X X X 450mA

Dimension

MDC-7220V / VTD (100Φ)

MDC-7220V TD-30 (100Φ)

MDC-7220F (68Φ)

COMPONENTS

▶Specifications and Designs are subject to change without prior notice due to improvement

28 MICRODIGITAL

1 Lens 2 IR-LED 3 OSD Board / Heater (Option : 6pcs) 4 Zoom / Focus Lever 5 VBS-Extra for connecting to LCD

· Please use the supplied wire when connecting to an external monitor. 6 3 Axis bracket

· Adjust the pan and tilt to give the correct angle of view.

MDC-8220VDN / TDN-30, 30H (100Ø)

VBS-EXTRA

COMPONENTS

MICRODIGITAL 29

MDC-8220 VDN TDN TDN-30 TDN-30H

Dimension

Diameter 100ø

Height 115mm

Width 145mm

IR LED

X X

30pcs

IR-LED

30pcs

IR-LED, 6pcs

Heater

Power Consumption

Normal 200mA

IR LED ON X X 400mA 400mA

Heater ON X X X 460mA

Dimension

COMPONENTS

▶Specifications and Designs are subject to change without prior notice due to improvement

30 MICRODIGITAL

Lens

• The camera is supplied without a lens. Lenses, such as auto iris, CS-Mount and C-Mount, can be used.

▹When using an auto iris lens

· Strip back about 8mm of the outer sheath of the auto iris lens cable.

· Strip off about 2mm of the insulation of wires inside the lens cable.

· Remove the cover of the auto iris lens connection plug and solder the

wires to the connector pins inside the plug, as shown below.

MDC-4xxx

INSTALLATION

MICRODIGITAL 31

· Replace the auto iris lens connection plug cover. Remove the lens

protection cap and then attach the auto iris lens to the camera by screwing it in clockwise.

· Insert the connection plug connected to the auto iris lens cable into

the auto lens connector jack, which is located on the rear of the camera.

· Set the lens selection switch, located on the rear of the camera, to ei-

ther DC or VIDEO, depending on the type of auto iris lens being used.

VIDEO TYPE LENS DC TYPE LENS

PIN NO. NAME WIRE COLOR NAME WIRE COLOR

1 OPEN NOT USE DAMP COIL - GREEN

2 VIDEO WHITE DAMP COIL + RED

3 POWER RED DRIVE COIL + BLACK

4 GROUND BLACK DRIVE COIL - BROWN

INSTALLATION

32 MICRODIGITAL

• There are three ~ four mounting holes on the bracket so that users can install the

unit in any place such as on the ceiling, On the wall, on the fence and etc.

• Fix the camera on the bracket.

• Please check the points below before connecting video & power cable.

• Adjust picture direction pan & tilt

Caution!

To avoid smear, never face the camera directly to the strong light source such as sun or spot light.

65ø / 75ø TYPE 76ø / 95ø TYPE

90ø TYPE

3 AXIS BRACKET

CABLE MANAGEMENT BRACKET

MOUNTING SCREW

MOUNTING SCREW MOUNTING SCREW

3 AXIS BRACKET

MDC-6xxx

INSTALLATION

MICRODIGITAL 33

• Open the dome with the ring unscrewed.

• There are two mounting holes on the dome base so that users can install the unit

in any place such as on the ceiling, on the wall, on the fence and etc.

• The mounting in any place connecting the video/power cable, before connecting

please check the below point.

• Adjust picture direction pan & tilting.

• Close the dome with the ring screwed.

Ceiling Ceiling

MDC-7220VDN / TDN / FDN30

(Three Screw)

MDC-722FDN (Two Screw)

MDC-7220TDN-30

(Three Screw)

MOUNTING SCREW

BASE HOUSING

DOME COVER

DOME COVER HOLDER

MDC-7xxx

INSTALLATION

34 MICRODIGITAL

• Open the dome cover on the base by L-Wrench.

• Remove the tapping screw on the dome camera base by screw driver.

▶ Surface type

· Fixed the surface mount bracket to a ceiling using three mounting screw.

· Draw out power/video wires to the connecting places.

· Insert dome camera base into the surface mount bracket.

· Fixed the dome camera base to a surface mount

bracket using three tapping screw.

Draw out power / video wires to the connecting places.

Fixed the camera to a celling using four screws.

Adjust desired focus and scene by turning and moving the 3-axis camera bracket by hand.

Put the dome cover over the base.

Fix the dome cover on the base by L-Wrench.

MDC-8xxx

INSTALLATION

MICRODIGITAL 35

▶ Flush type

· Remove the surface mount bracket then insert dome camera base into

the drilled holes.

· Draw out power/video wires to the connecting places.

· Fixed the dome camera base to a ceiling using three mounting screw.

• Adjust desired focus and scene by turning and moving 3-axis by hand.

• Close the dome cover on the base by L-Wrench.

Draw out power / video wires to the connecting places.

Fix the surface mount bracket by screws on the ceiling.

Adjust desired focus and scene by turning and moving the 3-axis camera bracket by hand.

Put the dome cover over the base.

Fix the dome cover on the base by L-Wrench.

Connect the dome base to the surface mount bracket by screws.

Ceiling

MDC-8xxx

INSTALLATION

36 MICRODIGITAL

1) Connection to Monitor

- As the connecting method varies with the instruments, refer to the manual sup-

plied with the instrument.

- If necessary, you can connect the monitor to the REMOTE jack on the back of

your camera.

- Only connect the cable when the power is furned off.

- Set the 75Ω / Hi-Z selection switch as shown below if you have an

intermediate device.

2) Connection to Power

- Connect the adaptor to the power input connector as shown in the following

figure. The Standard voltage for camera option : DC 12V± 10%, AC 24V ±10%.

MDC-4xxx

OSD OPERATION

Camera

Monitor

pypzGqhjr

}pklvGv|{

XY}Gkj

kv~u

slm{

ypno{

wv~ly

tlu|

mUn

pypzGqhjr

}pklvGv|{

XY}Gkj

kv~u

slm{

ypno{

wv~ly

tlu|

mUn

MICRODIGITAL 37

Settings can be made using the 4 or 5 buttons located on the nearby of the camera.

1) Connection to Monitor

- As the connecting method varies with the instruments, refer to the manual sup-

plied with the instrument.

- If necessary, you can connect the monitor to the REMOTE jack on the back of

your camera.

- Only connect the cable when the power is furned off.

- Set the 75Ω / Hi-Z selection switch as shown below if you have an

intermediate device.

Power Input

MDC-4xxx

MDC-6xxx

OSD OPERATION

Camera

pypzGqhjr

}pklvGv|{

XY}Gkj

kv~u

slm{

ypno{

wv~ly

tlu|

DOWN

LEFT

RIGHT

mUn

38 MICRODIGITAL

2) Connection to Power

- Connect the adaptor to the power input connector as shown in the following figure.

The Standard voltage for camera option : DC 12V± 10%, AC 24V ±10%.

Connecting to Monitor and Power

Power Input

NOTE

▪ Nomal we donnot use the RS-485 addisional cable. only have power and video

For 12V DC Power Type

- Connect the video-out jack to the video-in jack of monitor.

- Connect the power adapter to the power input connecter.

- Use 12V DC power source.

- Use the power rated at least 400mA (12VDC)

ellow)

Video

(Yellow)

ower - DC 12

Red

)

Power - DC 12V (Red)

Video Output

GND

NO Function

Terminal

Color

Remark

Video

Output

Yellow 1.0 Vp-p

Power

Input

Red

12V DC(10V~15V),

Max 4.8W / 400mA

MDC-6xxx

OSD OPERATION

MICRODIGITAL 39

Push(set)

MDC-6220TDN-20 / 20H

♦ Unscrew the front cover

MDC-6220TDN

-35H, 36H, 45, 48 ♦ Unscrew the OSD button cap

MDC-6220TDN

-24H, 42, 30, 40H

♦ Unscrew the front cover

MDC-6xxx

OSD OPERATION

40 MICRODIGITAL

MDC-7220FDN

♦ Unscrew the dome cover

MDC-7220VDN / TDN / TDN-30

♦ Unscrew the dome cover

Push(set)

MDC-7xxx

OSD OPERATION

MICRODIGITAL 41

Without Heater type OSD Board

With Heater type OSD Board

OSD Joystick

VBS-Extra Connector

Power

connector

Module connector

OSD OPERATION

MDC-8xxx

42 MICRODIGITAL

▶CONNECTION

▪Camera(BNC) ➜Remote Controller ➜ BNC ➜ Monitor / DVR

▶UTC Specification

Content Spec Remark

Support VIDEO format NTSC / PAL

Video Input Level 1.0 Vp-p / 75 Ohm BNC

Video Output Level 1.0 Vp-p / 75 Ohm BNC

Control OSD, PAN/Focus

Compatibility

MicroDigital

UTC Product Family

Except Other Companies

Distance Video Output Distance TEST : 500M (RG59)

Operation temperature -20°C ~ +60°C Standard

Dimension (W x D x H) 55 x 85 x 10 (mm)

Power CR2032 X 2 Battery

• Features

▪Long distance controller. ▪Menu can be adjusted without opening the camera case. ▪User can adjust OSD control during installation without the portable monitor. ▪It is of conveniently portable size.

BNC

CONNECTOR

Remote Controller

Monitor / DVR

DVD

UTC CONTROLLER

OSD OPERATION

MICRODIGITAL 43

▹ SET button

• Used for the menu display. This button can be used to confirm settings after

changing the value of the selected function or current conditions.

▹ UP & DOWN buttons

• Used for selecting items by moving the cursor up or down on the menu screen.

▹ LEFT & RIGHT buttons

• Used when changing item values, by moving the cursor to the left or right on the

menu screen.

Setting

▹ Use the OSD control switch on the main body of the camera ▹ Settings can be made using the 5 buttons located on the rear

of the camera

▹ Press the set switch

• The [SETUP] menu appears on the monitor screen

• Use UP and DOWN switch to select menu, then press SET switch ( )

· Submenu appears on monitor screen

• Set up selected item by using the LEFT and RIGHT switch ( )

• To finish and save the settings, select [EXIT] and press the SET button ( )

NOTE

▪ An item with the ↵ icon also has sub-menus. To select a sub-menu, press the

SET button.

▪ An item with the - - - icon has no sub-menus available for selection

INSTRUCTIONS

OSD(On Screen Display) Button

44 MICRODIGITAL

LENS

■ DC / VIDEO / MANUAL

EXPOSURE

■ SHUTTER

• 1/50~1/100K / x2~x256 /AUTO / FLK

■ BLC

• OFF / BLC / HSBLC

■ AGC

• LOW / MIDDLE / HIGH

■ D-WDR

• OFF / INDOOR / OUTDOOR

■ SENS-UP

• AUTO / OFF

■ RETURN

WHITE BAL.

■ ATW / AWB / MANUAL / AWC --->SET / INDOOR / OUTDOOR

DAY/NIGHT

■ AUTO / B/W / COLOR / EXT

3D DNR

■ ON(RANGE : 0~100 LEVEL SELECTABLE)/OFF

SPECIAL

■ CAMERA TITLE : ON/OFF ■ SYNC : INT

■ D-EFFECT

• FREEZE / MIRROR / D-ZOOM /

GAMMA / NEG.IMAGE / RETURN

■ LANGUAGE

• ENG / KOR / JPN / CHN1 /

CHN2 / RUS

■ RS 485

• CAM ID / ID-DISPLAY / BAUDRATE

■ DEFECT

• SENS-UP / DIFF / START / RETURN

■ MOTION

• AREA SELECT(4ch) / AREA

DISPLAY / SENSITIVITY / MOTION VIEW / RETURN

■ RETURN

■ PRIVACY

• AREA SELECT(8ch) / AREA

DISPLAY / COLOR / RETURN

ADJUST

■ SHARPNESS : 0 ~ 31 ■ MONITOR : CRT / LCD / USER

■ OSD COLOR : 0 ~ 15 ■ RETURN

RESET

■ FACTORY DEFAULT ■ RETURN

EXIT

■ SAVE SET UP MENU AND EXIT

Function Menu Structure

OSD STRUCTURE

MICRODIGITAL 45

▹ This function is Control brightness of the screen

• DC : select auto iris lens

· The brightness of the screen can be adjusted in DC mode.

· The brightness can be adjusted within the range of 0 ~100.

· The optimum level of brightness can be achieved using this adjustment.

• Video : select video lens

• Manual : select manual lens

1. LENS

2. EXPOSURE

3. BACKLIGHT

4. WHITE BAL.

5. DAY & NIGHT

6. SMART 3DNR

7. F – DNR

8. FUNCTION

9. EXIT

(MAUAL )

DWDR

ATW

AUTO

- - -

SAVE

MAIN MENU

1. BRIGHTNESS ∙∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙ 50

2. IRIS SPEED ∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙∙∙ 7

3. RETURN RET (SAVE & END )

1. BRIGHTNESS ∙∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙ 50

2. RETURN RET (SAVE & END )

DC LENS

MANUAL LENS

LENS

OSD STRUCTURE-MAIN MENU

NOTE

▪ If you press the Set button in "MANUAL LENS", You can Adjust brightness in

EXPOSURE.

▪ If you press the Set button in "VIDEO", You can't adjust brightness in EXPO-

SURE, Return to "LENS" and adjust lens type

*. F-DNR : Fog-Digital Noise Reduction DWDR : Digital Wide Dynamic Range

46 MICRODIGITAL

1. LENS

2. EXPOSURE

3. BACKLIGHT

4. WHITE BAL.

5. DAY & NIGHT

6. SMART 3DNR

7. F – DNR

8. FUNCTION

9. EXIT

(MAUAL )

DWDR

ATW

AUTO

- - -

SAVE

MAIN MENU

OFF(INDOOR,OUTDOOR) AUTO( FLK , OFF ) HIGH(LOW , MIDDLE) AUTO (OFF) RET (SAVE & END )

MODE SHUTTER AGC

SENSUP

RETURN

EXPOSEURE

SENS UP

*. SENSUP : Low shutter speed technology AGC : Auto Gain Control (MAX Gain) FLK : Flicker less Mode

MODE INDOOR SHUTTER - - - AGC HIGH(LOW , MIDDLE) SENSUP AUTO (OFF) RETURN RET (SAVE & END )

MODE OUTDOOR SHUTTER - - - AGC HIGH(LOW , MIDDLE) SENSUP AUTO (OFF) RETURN RET (SAVE & END )

MODE OFF SHUTTER FLK AGC HIGH(LOW , MIDDLE) SENSUP - - - RETURN RET (SAVE & END )

1. SENS UP x8

2. RETURN RET (SAVE & END )

OSD STRUCTURE-MAIN MENU

EXPOSURE

MICRODIGITAL 47

1. LENS

2. EXPOSURE

3. BACKLIGHT

4. WHITE BAL.

5. DAY & NIGHT

6. SMART 3DNR

7. F – DNR

8. FUNCTION

9. EXIT

(MAUAL )

DWDR (BLC ,HSBLC ,OFF)

ATW

AUTO

- - -

SAVE

MAIN MENU

1. LOW LEVEL ∙∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙ 8

2. HIGH LEVEL ∙∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙ 8

3. RETURN RET (SAVE & END )

1. VALUE MIDDLE(HIGH , LOW)

2. AREA SINGLE (DOUBLE )

3. DEFAULT

4. RETURN RET (SAVE & END )

1. GAIN ∙∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙ 50

2. MODE NIGHT ONLY(ALL DAY)

3. MASK LEVEL ∙∙∙∙∙∙∙∙∙∙∙∙∙I∙∙∙∙∙ 70

4. DEFAULT

5. M.SKIP AREA ON (OFF)

6. RETURN RET (SAVE & END )

D-WDR

BLC

HSBLC

*. BLC : Back Light Compensation HSBLC : Head light Suppress BLC

POSITION ( SIZE , RET AGAIN )

OSD STRUCTURE-MAIN MENU

BACKLIGHT

48 MICRODIGITAL

1. LENS

2. EXPOSURE

3. BACKLIGHT

4. WHITE BAL.

5. DAY & NIGHT

6. SMART 3DNR

7. F – DNR

8. FUNCTION

9. EXIT

1. LENS

2. EXPOSURE

3. BACKLIGHT

4. WHITE BAL.

5. DAY & NIGHT

6. SMART 3DNR

7. F – DNR

8. FUNCTION

9. EXIT

BLC ,(HSBLC ,OFF)

ATW

AUTO

OFF( AUTO ,MANUAL )

SAVE

DWDR

ATW (AWB,AWC->SET,

MANUAL ,INDOOR,OUTDOOR)

AUTO

- - -

SAVE

MAIN MENU

1. DETECT LEVEL ∙∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙ 3

2. RETURN RET (SAVE & END )

1. LEVEL ∙∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙ 20

2. COLOR GAIN I∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 0

3. EDGE GAIN I∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 0

4. GAMMA 0.55

5. RETURN RET (SAVE & END )

1. BLUE ∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙ 34

2. RED ∙∙∙∙I∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 14

3. RETURN RET (SAVE & END )

F – DNR AUTO

F – DNR MANUAL

MANUAL WB

*. ATW : Auto Tracking White Balance AWB : Auto White Balance AWC : Auto White balance one shot Control 3DNR : 3 Digital Noise Reduction

WHITE BAL.

OSD STRUCTURE-MAIN MENU

MICRODIGITAL 49

1. LENS

2. EXPOSURE

3. BACKLIGHT

4. WHITE BAL.

5. DAY & NIGHT

6. SMART 3DNR

7. F – DNR

8. FUNCTION

9. EXIT

DWDR

ATW

AUTO (EXT ,B/W ,COLOR)

- - -

SAVE

MAIN MENU

1. DELAY ∙∙∙∙∙I∙∙∙∙∙∙∙∙∙∙∙∙∙ 3

2. D N(AGC) ∙∙∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙ 118

3. N D(AGC) ∙∙∙I∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 40

4. RETURN RET (SAVE & END )

1. BURST OFF(ON)

2. IR SMART ON (OFF)

3. IR LED ON(OFF)

4. RETURN RET (SAVE & END )

1. VALUE ∙∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙ 50

2. AREA

3. IR WDR OFF OFF(∙∙∙∙∙I∙∙∙∙∙ 1~15)

4. RETURN RET (SAVE & END )

1. DELAY ∙∙∙∙∙I∙∙∙∙∙∙∙∙∙∙∙∙∙ 3

2. RETURN RET (SAVE & END )

D & N AUTO

D & N B/W

IR SMART

D & N EXT

*. D&N : Day and Night B/W : Black and White Image

POSITION ( SIZE , RET AGAIN )

DAY & NIGHT

OSD STRUCTURE-MAIN MENU

50 MICRODIGITAL

1. LENS

2. EXPOSURE

3. BACKLIGHT

4. WHITE BAL.

5. DAY & NIGHT

6. SMART 3DNR

7. F – DNR

8. FUNCTION

9. EXIT

1. LENS

2. EXPOSURE

3. BACKLIGHT

4. WHITE BAL.

5. DAY & NIGHT

6. SMART 3DNR

7. F – DNR

8. FUNCTION

9. EXIT

DWDR

ATW

AUTO

ON (OFF)

- - -

SAVE

DWDR

ATW

AUTO

ON (OFF)

- - -

SAVE

MAIN MENU

SMART 3DNR

FUCNTION

SMART 3DNR

*. SMART NR : Smart Noise Reduction

*. D-EFFECT : Digital Effect

COMM ADJ : Communication Adjustment

1. VALUE ∙∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙ 50

2. SMART NR OFF(ON)

3. SMART LEVEL - - -

4. SENSITIVITY - - -

5. RETURN RET (SAVE & END )

1. MOTION OFF(ON )

2. PRIVACY OFF(ON )

3. D-EFFECT

4. IMAGE ADJ

5. COMM ADJ

6. SYNC INT(LL)

7. LANGUAGE

8. RETURN RET (SAVE & END )

1. VALUE ∙∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙ 50

2. SMART NR ON

3. SMART LEVEL ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙I 200

4. SENSITIVITY ∙∙∙∙∙∙∙∙∙∙∙∙I∙∙∙∙∙ 80

5. RETURN RET (SAVE & END )

ENGLISH(ARAB, HEBREW, TURKI, POLISH, GERMAN, DOUCH, PORTU, ITALIANO, ESPANOL, FRANCAIS, PYCCNN, 简骵中文,繁骵

中文,日本語,한국어)

OSD STRUCTURE-MAIN MENU

SMART 3DNR

FUNCTION

MICRODIGITAL 51

FUCNTION

MOTION

PRIVACY

1. MOTION ON (OFF)

2. PRIVACY OFF(ON )

3. D-EFFECT

4. IMAGE ADJ

5. COMM ADJ

6. SYNC INT(LL)

7. LANGUAGE ENGLISH

8. RETURN RET (SAVE & END )

1. MOTION ON (OFF)

2. PRIVACY OFF(ON )

3. D-EFFECT

4. IMAGE ADJ

5. COMM ADJ

6. SYNC INT(LL)

7. LANGUAGE ENGLISH

8. RETURN RET (SAVE & END )

1. AREA 1(2, 3, 4 )

2. AREA DISPLAY ON (OFF)

3. VALUE ∙∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙ 80

4. MOTION VIEW ON (OFF)

5. RETURN RET (SAVE & END )

1. AREA 1(2, 3, 4, 5, 6, 7, 8 )

2. AREA DISPLAY ON (OFF)

3. COLOR ∙∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙ 10

4. TRANSPAR ∙∙I∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 3

5. RETURN RET (SAVE & END )

POSITION ( SIZE , RET AGAIN )

TOP LEFT(RIGHT) BTM LEFT(RIGHT) POSITION ( SIZE ,RET AGAIN )

OSD STRUCTURE-MAIN MENU

52 MICRODIGITAL

FUCNTION D-EFFECT

D-EFFECT SMART D-ZOOM

1. MOTION ON (OFF)

2. PRIVACY OFF(ON )

3. D-EFFECT

4. IMAGE ADJ

5. COMM ADJ

6. SYNC INT(LL)

7. LANGUAGE ENGLISH

8. RETURN RET (SAVE & END )

1. D-ZOOM OFF(ON)

2. SMART DZOOM OFF(ON )

3. DIS OFF(ON)

4. FREEZE OFF(ON)

5. MIRROR OFF(ROTATE, V-FLIP, MIRROR)

6. NEG. IMAGE OFF(ON)

7. RETURN RET (SAVE & END )

1. D-ZOOM OFF(ON)

2. SMART DZOOM OFF(ON )

3. DIS OFF(ON)

4. FREEZE OFF(ON)

5. MIRROR OFF

6. NEG. IMAGE OFF(ON)

7. RETURN RET (SAVE & END )

1. RANGE x1(2.1, … 5.0)

2. POSITION

3. SENSITIVITY ∙∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙ 80

4. TIME I∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 1

7. RETURN RET (SAVE & END )

*. TRANSPAR : Transparent NEG. : Negative Image DIS : Digital Image Stabilization

POSITION ( SIZE , RET AGAIN )

OSD STRUCTURE-MAIN MENU

MICRODIGITAL 53

FUCNTION IMAGE ADJ

MONITOR LCD

MONITOR CRT

1. MOTION ON (OFF)

2. PRIVACY OFF(ON )

3. D-EFFECT

4. IMAGE ADJ

5. COMM ADJ

6. SYNC INT(LL)

7. LANGUAGE ENGLISH

8. RETURN RET (SAVE & END )

1. SHARPNESS ∙∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙ 20

2. MONITOR LED (CRT )

3. LENS SHADING OFF(ON )

4. DEFECT

5. RETURN RET (SAVE & END )

1. GAMMA 0.55(USER, 0.05, 0.10,

0.15 ..0.95, 1.00)

2. PED LEVEL ∙∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙ 41

3. COLOR GAIN ∙∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙ 128

4. RETURN RET (SAVE & END )

1. PED LEVEL ∙∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙ 41

2. COLOR GAIN ∙∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙ 128

3. RETURN RET (SAVE & END )

*. PED LEVEL : Pedestal Level

OSD STRUCTURE-MAIN MENU

54 MICRODIGITAL

IMAGE ADJ

IMAGE ADJ DEFECT

COVER THE LENS

THEN

PRESS ENTER KEY

SAVING ….

LENS SHADING

1. SHARPNESS ∙∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙ 20

2. MONITOR LED (CRT )

3. LENS SHADING ON(OFF )

4. DEFECT

5. RETURN RET (SAVE & END )

1. SHARPNESS ∙∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙ 20

2. MONITOR LED (CRT )

3. LENS SHADING OFF(ON )

4. DEFECT

5. RETURN RET (SAVE & END )

1. SENS UP x16 (x4, x8, x16, x32, x64, x128)

2. DIFF ∙∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙ 2

3. THRESHOLD ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙I∙ 9

4. START

5. RETURN RET (SAVE & END )

1. LEVEL ∙∙∙∙∙I∙∙∙∙∙∙∙∙∙∙∙∙∙ 8

2. H-CENTER ∙∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙ 103

3. V-CENTER ∙∙∙∙∙∙∙∙∙I∙∙∙∙∙∙∙∙∙ 103

4. RETURN RET (SAVE & END )

*. H-CENTER : Horizontal center V-CENTER : Vertical center DIFF : Different level

OSD STRUCTURE-MAIN MENU

MICRODIGITAL 55

COM ADJ

RS485

CAM. 001

CAM TITLE

1. CAM TITLE OFF(ON )

2. PROTOCOL PELCO-D (NICP, DONG YANG, SPD-S, PELCO-P)

3. RS485

4. RETURN RET (SAVE & END )

1. CAM ID 1(2, 3, …. 255)

2. ID DISPLAY ON (OFF)

3. BAUDRATE 38400(4800, 9600, 19200, 57600)

4. RETURN RET (SAVE & END )

0123456789

ABCDEFGHIJK

LMNOPQRSTUV

WXY…………

<- -> CLR POS END

FUCNTION

1. MOTION ON (OFF)

2. PRIVACY OFF(ON )

3. D-EFFECT

4. IMAGE ADJ

5. COMM ADJ

6. SYNC INT(LL)

7. LANGUAGE ENGLISH

8. RETURN RET (SAVE & END )

*. ID : Identify

1. LENS

2. EXPOSURE

3. BACKLIGHT

4. WHITE BAL.

5. DAY & NIGHT

6. SMART 3DNR

7. F – DNR

8. FUNCTION

9. EXIT

DWDR

ATW

AUTO

- - -

SAVE (CANCEL , RESET )

MAIN MENU

OSD STRUCTURE-MAIN MENU

Ver.121015E

Design and specifications are subject to change without notice.

www.microdigital.co.kr sales@microdigital.co.kr #1212, Hoseodae Venture Tower, 319, Gasan-Dong, Geumcheon-Gu, Seoul, Korea Tel :+82-2-2627-5279 / Fax :+82-2-2627-5295

P/N : 3690-0002B

TOTAL SECURITYGSOLUTION

Supreme Resolution

Day & Night Color Camera

www.microdigital.co.kr

USER MANUAL

MicroDigial MDC-4, MDC-8, MDC-6 TDN, MDC-7 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual