CWT Series
Users Manual
www.microboards.com Version 2.2
CWT Series MICROBOARDS TECHNOLOGY, LLC
2
CWT Series MICROBOARDS TECHNOLOGY, LLC
TABLE OF CONTENTS
System Overview..................................................................................................5
Unpacking your system.........................................................................................5
Microboards Statement Regarding Improper Duplication .....................................5
Installation Requirements .....................................................................................6
Main Menu ............................................................................................................7
Copy Disc to Disc..................................................................................................7
Copy CD+G ..........................................................................................................7
Simulation Disc to Disc .........................................................................................7
Erasing RW media ................................................................................................8
Setup Menu ..........................................................................................................9
Mode Select................................................................................................10
CD WR Speed ............................................................................................10
ISRC Check ................................................................................................10
Auto Run.....................................................................................................10
Copy Quantity .............................................................................................10
Session Mode .............................................................................................10
Reader Select .............................................................................................10
Drive Inquiry................................................................................................10
F/W Version ................................................................................................10
F/W Update.................................................................................................10
Log..............................................................................................................10
Error Codes ........................................................................................................11
Specifications...................................................................................................... 17
Supported Formats .............................................................................................17
Firmware Updates...............................................................................................17
Technical Support ...............................................................................................17
3
CWT Series MICROBOARDS TECHNOLOGY, LLC
4
CWT Series MICROBOARDS TECHNOLOGY, LLC
System Overview
The CWT Series employs up to 10 General Purpose CD recorders.
An intuitive, menu driven
display and 5-button control
interface provide one-touch
operation for the novice user
while providing advanced
features for the professional.
Advanced Features:
• Stand-Alone CD-R duplicator
• One Touch duplication
• Auto Run option
• Speed selectable (4x to 48x for CD-R)
• Supports writing to CD-R/RW
• Copy and Verify
• Counter feature allows the user to input how many discs need to be copied and
• Simulation mode to ensure recording stability
• Easy-to-read, two-line display for status and error reporting
• Updates easily installed through CD reader
the keeps track of the total discs completed.
COPY START
(DISC to DISC)
Unpacking your system
When unpacking your duplicator, confirm the following items are included:
• CWT Series duplicator
• Power cable
• Quick Start Guide
• Starter Kit (includes User’s Manual and Warranty information)
If any of these items are missing, please contact or Microboards Technology Technical Support at
952-556-1639.
IMPORTANT: Please keep all the packing for your CWT Series duplicator. If your unit ever
needs to be sent in for service, it must be returned in the original packing or the warranty will be
voided.
Microboards Statement Regarding Improper Duplication
Microboards Technology fully supports the right of any business, organization, group, or
individual to protect their property from unlicensed, unauthorized, or illegal duplication.
As a user of our equipment, we expect you to support that right as well.
Microboards Technology is neither responsible nor liable for the infringement of any laws
regarding the illegal duplication of property. Microboards Technology products are in no way
intended to encourage or condone such duplication.
5
CWT Series MICROBOARDS TECHNOLOGY, LLC
Installation Requirements
System Setup
• Connect the power cable to the CWT Series tower and plug in to a protected power outlet
strip or UPS power supply.
• Turn on power to the tower. The system is now ready to use.
Install your CWT Series duplicator in the following environment:
• On a level and stable surface
• In a well ventilated location
• Temperature and humidity
• Temperature: 5-40°
• Humidity: 20-80%RH (no dew formation)
Do not install it in the following places:
Under direct sunlight (If the machine is exposed to sunlight, the light should be blocked
by a curtain or blind.)
A dusty location
A place where there is a lot of vibration
Near open flame
A place where the temperature and humidity change drastically
Near a heating device such as a heater or furnace
A location where air from an air conditioner blows directly onto the unit
Near a container filled with water such as a vase
In winter during times of low humidity or in a location where static electricity is
generated, use an anti-static-electricity mat or humidifier to prevent static electricity.
Power supply
Use house current as the power source for the unit.
Do not use an outlet near a motor driven appliance (i.e. air conditioner, copying
machine).
Use an outlet with stable power supply voltages.
Do not overload an outlet. Do not use a service outlet from a PCs or other office
machine.
Wire the power cord properly.
Do not touch the power cord with a wet hand.
Be careful not to damage the power cord.
Inspect the power cord periodically.
In the event that the power cord is damaged, replace the power cord.
Be sure to use a tool such as the screwdriver to change the 115/230V Switch.
Do not use your finger.
6
CWT Series MICROBOARDS TECHNOLOGY, LLC
Main Menu
The Arrow buttons (▼▲) allow you to move forward or backward in the menu without selecting
the current menu item. The NO button will move you to the next menu item. YES will select the
current menu item.
COPY START?
(DISCtoDISC)
COPY CD+G START?
(DISCtoDISC)
SIMULATION?
(DISCtoDISC)
ESC
DISC ERASE?
(REWRITABLE)
ESC
SETUP?
(MODE CHANGE)
NO,▼
NO,▼
NO,▼
NO,▼
NO/ESC
YES
YES
YES
ANALYZING MASTER
YES
>QUICK ERASE?
>QUICK ERASE?
>EXIT?
YES
SETUP MENU
(see pg 9)
NO,▼
NO,▼
NO,▼
COPY 15:26 ANALYZING MASTER
CD-DA 20%
COPY 15:26 ANALYZING MASTER
CD-DA 20%
SIMULATION 15:26
CD-DA 20%
SURE ? DISC ERASE
YES
YES
SURE ? DISC ERASE
YES
YES
Please wait...
Please wait...
Copy Disc to Disc
1. Place the Master Disc into the Reader drive.
Place the blank disc(s) into the Recorder drive(s) and wait for the light(s) on the front of
the Recorder(s) to stop blinking.
Copy Start?
(DISC to DISC)
2. The display reads COPY START? (DISC to DISC).
3. Press YES. If you have the Auto Run feature set to ON, the duplication will begin when
the master is loaded and all drives are loaded with blank media.
4. The drive trays will open on any recorder without blank discs installed. If you do not want
to make a copy in those drives, close the tray(s), wait for the drive light to go out, and
then press the YES button to start the copy job.
5. The display will now show the progress of the Copy Job.
COPY 425.0MB
CD 25%
6. The Recorder(s) will eject the recorded discs when the job is complete.
Copy CD+G
Use this menu to copy CD+G discs.
Follow the steps listed in the Copy Disc to Disc section above.
Simulation Disc to Disc
1. At the COPY START? (DISC to DISC) menu, press the NO or ▼ button until the display
shows SIMULATION? (DISC to DISC).
SIMULATION??
(DISC to DISC)
2. Place the Master Disc into the Reader drive
7
CWT Series MICROBOARDS TECHNOLOGY, LLC
3. Place the blank disc(s) into the Recorder drive(s) and wait 10 seconds for the light(s) on
the front of the Recorder(s) to stop blinking.
4. Press YES.
5. The drive trays will open on any recorder without blank discs installed. If you do not want
to make a copy in those drives, close the tray(s), wait for the drive light to go out, and
then press the YES button to start the copy job.
6. The display will now show the progress of the Simulation Copy Job
SIMULATION 425.0MB
CD 25%
7. The Recorder(s) will eject the still-blank discs when the job is complete.
Erasing RW media
1. At the COPY START? (DISC to DISC) menu, press the NO or ▼ button until the display
shows DISC ERASE? (REWRITABLE):
DISC ERASE?
(REWRITABLE)
2. Load the Recorder(s) with the CD-RW media you wish to erase. You can erase one disc
at a time or fill all the Recorders to erase multiple discs at once. All discs loaded must be
of the same type.
3. Press the YES button
4. The next screen asks if you want to perform a Quick Erase.
QUICK ERASE?
If you wish to perform a Full Erase, press the NO button.
FULL ERASE?
Pressing the YES button at either of these selections will show the following screen:
SURE?
5. Press the YES button if you are sure you want to erase the RW disc. If you do not wish
to erase the disc, press the NO button and you will go back to the DISC ERASE screen
(step 1).
6. The screen will now show:
DISC ERASE
7. Once the erasing is complete, the Recorder(s) will eject the disc(s).
8
CWT Series MICROBOARDS TECHNOLOGY, LLC
Setup Menu
SETUP
Yes
MODE SELECT?
(COPY MODE)
Yes
COPY?
(DISC to DISC)
VERIFY?
(DISC to DISC)
COPY + V?
(DISC to DISC)
EXIT?
COPY?
CD WR SPEED?
(MAX)
ISRC CHECK?
(OFF)
Auto Run?
(OFF)
COPY QUANTITY?
(xxxx/xxxx)
Session Mode?
(AUTO)
Reader Select?
(DRIVExx)
DRIVE INQUIRY?
Yes
Yes
Yes
Yes
Yes
Yes
Yes
MAX?
ISRC ON?
ON?
COPY QUANTITY?
0---
AUTO?
DRIVE01
READER
DRIVE02
RECORDER
DRIVExx
RECORDER
EXIT?
DRIVE01
READER
DRIVE02
RECORDER
48X? EXIT?
4X?
ISRC OFF?
EXIT?
ISRC ON?
OFF?
CLOSE? OPEN? EXIT?
THE DISPLAY WILL CYCLE
THROUGH THE MAKE, MODEL,
AND FIRMWARE OF THE
SELECTED DRIVE UNTIL YOU
PRESS A BUTTON.
DRIVE01
READER
THE DISPLAY WILL CYCLE
THROUGH THE MAKE, MODEL,
AND FIRMWARE OF THE
SELECTED DRIVE UNTIL YOU
PRESS A BUTTON.
MAX?
AUTO?
DRIVExx
RECORDER
EXIT?
F/W VERSION
F/W UPDATE
LOG?
EXIT?
Yes
Yes
Yes
Premium 1020
VER A.BC
INSERT
PROGRAM DISC
OK xxxxxxx
NG xxxxxxx
MODE SELECT?
(COPY MODE)
DRIVE01
READER
Checking
9
H/W INFO
12ΦπρΨ
KEY
EXIT?
UPDATE?
VER a.bc -> b.cd
Yes
Premium 1020
VER A.BC
Updating
Caption indicates button to press
No caption indicates display seq uence
▲ (Back), NO, or ▼ (Forward)
YES (Accept) or ESC (Return to Menu)
Complete
CWT Series MICROBOARDS TECHNOLOGY, LLC
Setup Menu
1. At the COPY START? (DISC to DISC) menu, press the NO or ▼ button until the display
shows SETUP? (MODE CHANGE)
SETUP?
(MODE CHANGE)
2. Press the YES button
3. The first setup option is Mode Select, followed by Write Speeds, ISRC Check, Copy
Quantity, Session Mode, Drive Inquiry, Firmware Version and Exit.
4. Pressing the NO or ▼ button will allow you to move from menu to menu.
5. Pressing the YES button will allow you to view or change the configuration of the system.
6. Please follow the flow chart on page 9 to navigate through the different menus.
Here is a description of each setup menu item:
Mode Select
COPY - Duplication from master disc to blank disc.
VERIFY - It compares a copied disc with the master disc.
COPY+V - Copying in the COPY+VERIFY mode
CD WR Speed
Available speeds range from 52x down to 4x.
ISRC Check
Default setting is ON. This feature will copy the ISRC codes from the Master audio disc to the
blank discs.
Auto Run
Default setting is OFF. When set to ON, this allows the duplicator to start the duplication process
when all recorders are loaded with blank media. The master must also be loaded before
duplication will begin.
Copy Quantity
Set up the number of disc you want to copy.
Use the ▼▲buttons to change the number in the current column up or down. YES will move you
one column to the right, NO will move you 1 column to the left. Press YES when in the right
column to save the number of copies entered. The example above shows that 750 copies have
been entered with the cursor currently in the right column (underlined).
Session Mode
Select either from AUTO, CLOSE, or OPEN.
AUTO: Make the session of copied disc as same as the master.
CLOSE: Close the session of copied disc.
OPEN: Leave the session of copied disc open.
Reader Select
Changes which drive is selected as the reader. This setting should not be changed.
Drive Inquiry
Displays an inquiry of each drive connected, showing drive model and firmware.
F/W Version
Shows CWT Series firmware version and H/W information.
F/W Update
Used when updating the firmware of the CWT Series duplicator.
Log
Displays the number of successful and unsuccessful discs over the entire life of the duplicator.
>>COPY QUANTITY
0750
10
CWT Series MICROBOARDS TECHNOLOGY, LLC
Error Codes
Read Errors
ASC ASCQ Description
00 00 NO ADDITIONAL SENSE INFORMATION
00 06 I/O PROCESS TERMINATED, PLAY OPERATION ABORTED
00 11 AUDIO PLAY OPERATION IN PROGRESS
00 12 AUDIO PLAY OPERATION PAUSE
00 13 AUDIO PLAY OPERATION SUCCESSFULLY COMPLETED
00 14 AUDIO PLAY OPERATION STOPPED DUE TO ERROR
00 15 NO CURRENT AUDIO STATUS TO RETURN
00 17 CLEANINF REQUESTED
01 00
02 00 NO SEEK COMPLETE
04 00 LOGICAL UNIT NOT READY, CAUSE NOT REPORTABLE
04 01 LOGICAL UNIT IS IN PROCESS OF BECOMING READY
04 02 LOGICAL UNIT NOT READY, INITIALIZING CMD. REQUESTED
04 03 LOGICAL UNIT NOT READY, MANUAL INTERVENTION REQUIRED
04 07 LOGICAL UNIT NOT READY, OPERATION IN PROGRESS
05 00 LOGICAL UNIT DOES NOT RESPOND TO SELECTION
06 00 NO REFERENCE POSITION FOUND (medium may be upside down)
08 00 LOGICAL UNIT COMMUNICATION FAILURE
08 01 LOGICAL UNIT COMUUNICATION TIME-OUT
08 02 LOGICAL UNIT COMMUNICATION PARITY ERROR
08 03 LOGICAL UNIT COMMUNICATION CRC ERROR (ULTRA-DMA/32)
09 00 TRACK FOLLOWING ERROR
09 01 TRACKING SERVO FAILURE
09 02 FOCUS SERVO FAILURE
09 03 SPINDLE SERVO FAILURE
0A 00 ERROR LOG OVERFLOW
0B 00 WARNING
0B 01 WARNING-SPECIFIED TEMPERATURE EXCEEDED
0B 02 WARNING-ENCLOSURE DEGRADED
10 00 ID CRC OR ECC ERROR
11 01 UNRECOVERED READ ERROR
11 02 ERROR TOO LONG TO CORRECT
11 05 L-EC UNCORRECTABLE ERROR
11 06 CIRC UNRECOVERED ERROR
11 0F ERROR READING UPC/EAN NUMBER
11 10 ERROR – LOSS PF STREAMING
12 00 ADDRESS MARK NOT FOUND FOR ID FIELD
13 00 ADDRESS MARK NOT FOUND FOR DATA FIELD
14 01 RECORD NOT FOUND
14 05 RECORD NOT FOUND – RECOMMEND REASSIGNMENT
14 06 RECORD NOT FOUND – DATA AUTO – REALLOCATED
15 00 RANDOM POSITIONING ERROR
15 01 MECHANICAL POSITIONING ERROR
15 02 POSITIONING ERROR DETECTED BY READ OF MEDIUM
17 00 RECOVERED DATA WITH NO EEOR CORRECTION APPLIED
17 01 RECOVERED DATA WITH RETRIES
17 02 RECOVERED DATA WITH POSITIVE HEAD OFFSET
17 03 RECOVERED DATA WITH NEGATIVE HEAD OFFSET
17 04
17 05
18 00 RECOVERED DATA WITH ERROR CORRECTION APPLIED
18 01 RECOVERED DATA WITH ERROR CORP. & RETRIES APPLIED
18 03 RECOVERED DATA WITH CIRC
18 04 RECOVERED DATA WITH L-EC
1A 00 PARAMETER LIST LENGTH ERROR
1B 00 SYNCHRONOUS DATA TRANSFER ERROR
1E 00 RECOVERED ID WITH ECC CORRECTION
NO INDEX/SECTOR SIGNAL
RECOVERED DATA WITH RETIES AND/OR CIRC APPLIED
RECOVERED DATA USING PREVIOUS SECTOR ID
11
CWT Series MICROBOARDS TECHNOLOGY, LLC
20 00 INVALID COMMAND OPERATION CODE
21 00 LOGICAL BLOCK ADDRESS OUT OF RANGE
24 00 INVALID FIELD IN CDB
25 00 LOGICAL UNIT NOT SUPPORTED
26 00 INVALID FIELD IN PARAMETER LIST
26 01 PARAMETER NOT SUPPORTED
26 02 PARAMETER VALUE INVALID
26 03 THRESHOLD PARAMETERS NOT SUPPORTED
26 04 INVALID RELEASE OF ACTIVE PERSISTENT RESERVATION
28 00 NOT READY TO READY CHANGE, MEDIUM MAY HAVE CHANGED
29 00 POWER ON, RESET, OR BUS DEVICE RESET OCCURRED
29 01 POWER ON OCCURRED
29 02 SCSI BUS RESET OCCURRED
29 03 BUS DEVICE RESET FUNCTION OCCURRED
29 04 DEVICE INTERNAL RESET
2A 00 PARAMETERS CHANGED
2A 01 MODE PARAMETERS CHANGED
2A 02 LOG PARAMETERS CHANGED
2A 03 RESERVATIONS PREEMPTED
2B 00 COPY CANNOT EXECUSE SINCE HOST CANNOT DISCONNECT
2C 00 COMMAND SEQUENCE ERROR
2C 05 PERSISTENT PREVENT CONFLICT
2F 00 COMMANDS CLEARED BY ANOTHER INITIATOR
30 00 INCOMPATIBLE MEDIUM INSTALLED
30 01 CANNOT READ MEDIUM - UNKNOWN FORMAT
30 02 CANNOT READ MEDIUM – INCOMPATIBLE FORMAT
30 03 CLEASNING CARTRIDGE INSTALLED
35 00 ENCLOSURE SERVICES FAILURE
35 01 UNSUPPORTED ENCLOSURE FUNCTION
35 02 ENCLOSURE SERVICES UNAVAILABLE
35 03 ENCLOSURE SERVICES TRANSFER FAILURE
35 04 ENCLOSURE SERVICES TRANSFER REFUSED
39 00 SAVING PARAMETERS NOT SUPPORTED
3A 00 MEDIUM NOT PRESENT
3A 01 MEDIUM NOT PRESENT-TRAY CLOSED
3A 02 MEDIUM NOT PRESENT-TRAY OPEN
3B 0F END OF MEDIUM REACHED
3B 11 MEDIUM MAGAZINE NOT ACCESSIBLE
3B 12 MEDIUM MAGAZINE REMOVED
3B 13 MEDIUM MAGAZINE INSERTED
3B 14 MEDIUM MAGAZINE LOCKED
3B 15 MEDIUM MAGAZINE UNLOCKED
3B 16 MECHANICAL POSITIONING OR CHANGER ERROR
3D 00 INVALID BITS IN IDENTIFY MESSAGE
3E 00 LOGICAL UNIT HAS NOT SELF-CONFIGURED YET
3E 01 LOGICAL UNIT FAILURE
3E 02 TIMEOUT ON LOGICAL UNIT
3F 00 TARGET OPERATING CONDITIONS HAVE CHANGED
3F 01 MICROCODE HAS BEEN CHANGED
3F 02 CHANGED OPERATING DEFINITION
3F 03 INQUIRY DATA HAS CHANGED
40 NN DIAGNOSTIC FAILURE ON COMPONENT NN (80H-FFH)
43 00 MESSAGE ERROR
44 00 INTERNAL TARGET FAILURE
45 00 SELECT OR RESELECT FAILURE
46 00 UNSUCCESSFUL SOFT RESET
47 00 SCSI PARITY ERROR
48 00 INITIATOR DETECTED ERROR MESSAGE RECEIVED
49 00 INVALID MESSAGE ERROR
4A 00 COMMAND PHASE ERROR
4B 00 DATA PHASE ERROR
4C 00 LOGICAL UNIT FAILED SELF-CONFIGURATION
12
CWT Series MICROBOARDS TECHNOLOGY, LLC
4D NN TAGGED OVERLAPPED COMMANDS (NN=QUEUE TAG)
4E 00 OVAERLAPPED COMMANDS ATTEMPTED
53 00 MEDIA LOAD OR EJECTED FAILED
53 02 MEDIUM REMOVAL PREVENTED
55 00 SYSTEM RESOURCE FAILURE
57 00 UNABLE TO RECOVER TABLE-OF-CONTENTS
5A 00 OPERATOR REQUEST OR STATE CHANGE INPUT
5A 01 OPERATOR MEDIUM REMOVAL REQUEST
5B 00 LOG EXCEPTION
5B 01 THRESHOLD CONDITION MET
5B 02 LOG COUNTER AT MAXIMUM
5B 03 LOG LIST CODES EXHAUSTED
5D 00 FAILURE PREDICTION THRESHOLD EXCEEDED - Predicted Logical Unit Failure
5D 01 FAILURE PREDICTION THRESHOLD EXCEEDED - Predicted Media Failure
5D FF FAILURE PREDICTION THRESHOLD EXCEEDED (FALSE)
5E 00 LOW POWER CONDITION ON
5E 01 IDLE CONDITION ACTIVATED BY TIMER
5E 02 STANDBY CONDITION ACTIVATED BY COMMAND
5E 03 IDLE CONDITION ACTIVATED BY COMMAND
5E 04 STANDBY CONDITION ACTIVATED BY COMMAND
63 00 END OF USER AREA ENCOUNTERED ON THIS TRACK
63 01 PACKET DOES NOT FIT IN AVAILABLE SPACE
64 00 ILLEGAL MODE FOR THIS TRACK
65 00 VOLTAGE FAULT
73 00 CD CONTROL ERROR
80 xx VENDOR SPECIFIC
Write Errors
ASC ASCQ Description
00 00 NO ADDITIONAL SENSE INFORMATION
00 06 I/O PROCESS TERMINATED, PLAY OPERATION ABORTED
00 11 AUDIO PLAY OPERATION IN PROGRESS
00 12 AUDIO PLAY OPERATION PAUSED
00 13 AUDIO PLAY OPERATION SUCCESSFULLY
00 14 AUDIO PLAY OPERATION STOPPED DUE TO ERRPOR
00 15 NO CURRENT AUDIO STATUS TO RETURN
02 00 NO SEEK COMPLETE
04 00 LOGICAL UNIT NOT READY, CAUSE NOT REPORTABLE
04 01 LOGICAL UNIT IS IN PROCESS OF BECOMING READY
04 02 LOGICAL UNIT NOT READY, INITIALIZING CMD. REQUIRED
04 03 LOGICAL UNIT NOT READY, MANUAL INTERVENTION REQUIRED
04 04 LOGICAL UNIT NOT READY, FORMAT IN PROGRESS
04 07 LOGICAL UNIT NOT READY, OPERATION IN PROGRESS
04 08 LOGICAL UNIT NOT READY, LONG WRITE IN PROGRESS
05 00 LOGICAL UNIT DOES NOT RESPOND TO SELECTION
06 00 NO REFERENCE POSITION FOUND
08 00 LOGICAL UNIT COMMUNICATION FAILURE
08 01 LOGICAL UNIT COMUUNICATION TIME-OUT
08 02 LOGICAL UNIT COMMUNICATION PARITY ERROR
08 03 LOGICAL UNIT COMMUNICATION CRC ERROR (ULTRA-DMA/32)
09 00 TRACK FOLLOWING ERROR
09 01 TRACKING SERVO FAILURE
09 02 FOCUS SERVO FAILURE
09 03 SPINDLE SERVO FAILURE
0A 00 ERROR LOG OVERFLOW
0B 00 WARNING
0B 01 WARNING-SPECIFIED TEMPERATURE EXCEEDED
0B 02 WARNING-ENCLOSURE DEGRADED
0C 00 WRITE ERROR
0C 02 WRITE ERROR-RECOVERED WITH AUTO REALLOCATION
13
CWT Series MICROBOARDS TECHNOLOGY, LLC
0C 03 WRITE ERROR-RECOMMEND REASSIGNMENT
0C 07 WRITE ERROR-RECOVERY NEEDED
0C 08 WRITE ERROR-RECOVERY FAILED
0C 09 WRITE ERROR-LOSS OF STREAMING
0C 0A WRITE ERROR-PADDING BLOCKS ADDED
11 00 UNRECOVERED READ ERROR
11 06 CIRC UNRECOVERED ERROR
15 00 RANDOM POSITIONING ERROR
15 01 MECHANICAL POSITIONING ERROR
15 02 POSITIONING ERROR DETECTED BY READ OF MEDIUM
16 00 DATA SYNCHRONIZATION MARK ERROR
16 01 DATA SYNC ERROR-DATA REWRITTEN
16 02 DATA SYNC ERROR-RECOMMEND REWRITE
16 03 DATA SYNC ERROR-DATA ATUO-REALLOCATED
16 04 DATA SYNC ERROR-RECOMMEND REASSIGNMENT
17 00 RECOVERED DATA WITH NO ERROR CORRECTION APPLIED
17 01 RECOVERED DATA WITH RETRIES
17 02 RECOVERED DATA WITH POSITIVE HEAD OFFSET
17 03 RECOVERED DATA WITH NEGATIVE HEAD OFFSET
17 04 RECOVERED DATA WITH RETRIES AND/OR CIRC APPLIED
17 05 RECOVERED DATA USING PREVIOUS SECTOR ID
17 06 RECOVERED DATA WITHOUT ECC - DATA AUTO-REALLOCATED
17 07 RECOVERED DATA WITHOUT ECC - RECOMMEND REASSIGNMENT
17 08 RECOVERED DATA WITHOUT ECC - RECOMMEND REWRITE
17 09 RECOVERED DATA WITHOUT ECC - DATA REWRITTEN
18 00 RECOVERED DATA WITH ERROR CORRECTION APPLIED
18 01 RECOVERED DATA WITH ERROR CORR. & RETRIES APPLIED
18 02 RECOVERED DATA - DATA AUTO-REALLOCATED
18 03 RECOVERED DATA WITH CIRC
18 04 RECOVERED DATA WITH L-EC
18 05 RECOVERED DATA - RECOMMEND REASSIGNMENT
18 06 RECOVERED DATA - RECOMMEND REWRITE
18 07 RECOVERED DATA WITH ECC - DATA REWRITTEN
19 00 DEFECT LIST NOT ERROR
19 01 DEFECT LIST NOT AVAILABLE
19 02 DEFECT LIST ERROR IN PRIMARY LIST
19 03 DEFECT LIST ERROR IN GROWN LIST
1A 00 PARAMETER LIST LENGTH ERROR
1B 00 SYNCHRONOUS DATA TRANSFER ERROR
1C 00 DEFECT LIST NOT FOUND
1C 01 PRIMARY DEFECT LIST NOT FOUND
1C 02 GROWN DEFECT LIST NOT FOUND
1D 00 MISCOMPARE DURING VERIFY OPERATION
20 00 INVALID COMMAND OPERATION CODE
21 00 LOGICAL BLOCK ADDRESS OUT OF RANGE
21 02 INVALID ADDRESS FOR WRITE
24 00 INVALID FIELD IN CDB
25 00 LOGICAL UNIT NOT SUPPORTED
26 00 INVALID FIELD IN PARAMETER LIST
26 01 PARAMETER NOT SUPPORTED
26 02 PARAMETER VALUE INVALID
26 03 THRESHOLD PARAMETERS NOT SUPPORTED
26 04 INVALID RELEASE OF ACTIVE PERSISTENT RESERVATION
27 00 WRITE PROTECTED
27 01 HARDWARE WRITE PROTECTED
27 02 LOGICAL UNIT SOFTWARE WRITE PROTECTED
27 03 ASSOCIATED WRITE PROTECT
27 04 PERSISTENT WRITE PROTECT
27 05 PERSISTENT WRITE PROTECT
27 06 CONDITIONAL WRITE PROTECT
28 00 NOT READY TO READY CHANGE, MEDIUM MAY HAVE CHANGED
29 00 POWER ON, RESET, OR BUS DEVICE RESET OCCURRED
14
CWT Series MICROBOARDS TECHNOLOGY, LLC
29 01 POWER ON OCCURRED
29 02 SCSI BUS RESET OCCURRED
29 03 BUS DEVICE RESET FUNCTION OCCURRED
29 04 DEVICE INTERNAL RESET
2A 00 PARAMETERS CHANGED
2A 01 MODE PARAMETERS CHANGED
2A 02 LOG PARAMETERS CHANGED
2A 03 RESERVATIONS PREEMPTED
2B 00 COPY CANNOT EXECUSE SINCE HOST CANNOT DISCONNECT
2C 00 COMMAND SEQUENCE ERROR
28 00 NOT READY TO READY CHANGE, MEDIUM MAY HAVE CHANGED
29 00 POWER ON, RESET, OR BUS DEVICE RESET OCCURRED
2A 00 PARAMETERS CHANGED
2A 01 MODE PARAMETERS CHANGED
2C 00 COMMAND SEQUENCE ERROR
2C 03 CURRENT PROGRAM AREA IS NOT EMPTY
2C 04 CURRENT PROGRAM AREA IS EMPTY
2C 05 PERSISTENT PREVENT CONFLICT
2E 00 INSUFFICIENT TIME FOR OPERATION
2F 00 COMMANDS CLEARED BY ANOTHER INITIATOR
30 00 INCOMPATIBLE MEDIUM INSTALLED
30 01 CANNOT READ MEDIUM - UNKNOWN FORMAT
30 02 CANNOT READ MEDIUM - INCOMPATIBLE FORMAT
30 05 CANNOT WRITE MEDIUM - INCOMPATIBLE FORMAT
30 06 CANNOT FORMAT MEDIUM - INCOMPATIBLE MEDIUM
30 08 CANNOT WRITE - APPLICATION CODE MISMATCH
30 09 CURRENT SESSION NOT FIXATED FOR APPEND
31 00 MEDIUM FORMAT CORRUPTED
31 01 FORMAT COMMAND FAILED
32 00 NO DEFECT SPARE LOCATION AVAILABLE
32 01 DEFECT LIST UPDATE FAILURE
35 00 ENCLOSURE SERVICES FAILURE
35 01 UNSUPPORTED ENCLOSURE FUNCTION
35 02 ENCLOSURE SERVICES UNAVAILABLE
35 03 ENCLOSURE SERVICES TRANSFER FAILURE
35 04 ENCLOSURE SERVICES TRANSFER REFUSED
37 00 ROUNDED PARAMETER
39 00 SAVING PARAMETERS NOT SUPPORTED
3A 00 MEDIUM NOT PRESENT
3A 01 MEDIUM NOT PRESENT - TRAY CLOSED
3A 02 MEDIUM NOT PRESENT - TRAY OPEN
3D 00 INVALID BITS IN IDENTIFY MESSAGE
3E 00 LOGICAL UNIT HAS NOT SELF-CONFIGURED YET
3E 01 LOGICAL UNIT FAILURE
3E 02 TIMEOUT ON LOGICAL UNIT
3F 00 TARGET OPERATING CONDITIONS HAVE CHANGED
3F 01 MICROCODE HAS BEEN CHANGED
3F 02 CHANGED OPERATING DEFINITION
3F 03 INQUIRY DATA HAS CHANGED
40 NN DIAGNOSTIC FAILURE ON COMPONENT NN (80H-FFH)
43 00 MESSAGE ERROR
44 00 INTERNAL TARGET FAILURE
45 00 SELECT OR RESELECT FAILURE
46 00 UNSUCCESSFUL SOFT RESET
47 00 SCSI PARITY ERROR
48 00 INITIATOR DETECTED ERROR MESSAGE RECEIVED
49 00 INVALID MESSAGE ERROR
4A 00 COMMAND PHASE ERROR
4B 00 DATA PHASE ERROR
4C 00 LOGICAL UNIT FAILED SELF-CONFIGURATION
4D NN TAGGED OVERLAPPED COMMANDS (NN=QUEUE TAG)
4E 00 OVAERLAPPED COMMANDS ATTEMPTED
15
CWT Series MICROBOARDS TECHNOLOGY, LLC
51 00 ERASE FAILURE
51 01 ERASE FAILURE - Incomplete erase operation detected
53 00 MEDIA LOAD OR EJECT FAILED
53 02 MEDIUM REMOVAL PREVENTED
55 00 SYSTEM RESOURCE FAILURE
57 00 UNABLE TO RECOVER TABLE-OF-CONTENTS
5A 00 OPERATOR REQUEST OR STATE CHANGE INPUT
5A 01 OPERATOR MEDIUM REMOVAL REQUEST
5A 02 OPERATOR SELECTED WRITE PROTECT
5A 03 OPERATOR SELECTED WRITE PERMIT
5B 00 LOG EXCEPTION
5B 01 THRESHOLD CONDITION MET
5B 02 LOG COUNTER AT MAXIMUM
5B 03 LOG LIST CODES EXHAUSTED
5D 00 FAILURE PREDICTION THRESHOLD EXCEEDED -
5D 01 FAILURE PREDICTION THRESHOLD EXCEEDED - Predicted Media Failure
5D 03 FAILURE PREDICTION THRESHOLD EXCEEDED - Predicted Spare Area Exhaustion
5D FF FAILURE PREDICTION THRESHOLD EXCEEDED (FALSE)
5E 00 LOW POWER CONDITION ON
5E 01 IDLE CONDITION ACTIVATED BY TIMER
5E 02 STANDBY CONDITION ACTIVATED BY COMMAND
5E 03 IDLE CONDITION ACTIVATED BY COMMAND
5E 04 STANDBY CONDITION ACTIVATED BY COMMAND
63 00 END OF USER AREA ENCOUNTERED ON THIS TRACK
64 00 ILLEGAL MODE FOR THIS TRACK
64 01 INVALID PACKET SIZE
65 00 VOLTAGE FAULT
72 00 SESSION FIXATION ERROR
72 01 SESSION FIXATION ERROR WRITING LEAD-IN
72 02 SESSION FIXATION ERROR WRITING LEAD-OUT
72 03 SESSION FIXATION ERROR - INCOMPATIBLE TRACK IN SESSION
72 04 EMPTY OR PARTIALLY WRITTEN RESERVED TRACK
72 05 NO MORE RZONE RESERVATIONS ARE ALLOWED
73 00 CD CONTROL ERROR
73 01 POWER CALIBRATIOIN AREA ALMOST FULL
73 02 POWER CALIBRATION AREA IS FULL
73 03 POWER CALIBRATION AREA ERROR
73 04 PROGRAM MEMORY AREA UPDATE FAILURE
73 05 PROGRAM MEMORY AREA/RMA IS FULL
73 06 PROGRAM MEMORY AREA/RMA IS (almost) FULL
B6 00 MEDIA LOAD/EJECT MECHANISM FAILED
B9 00 PLAY OPERATION ABORTED
80 FF VENDOR SPECIFIC
16
CWT Series MICROBOARDS TECHNOLOGY, LLC
Specifications
Recorder Drive: CD-R/RW Recorder
Power Source: 115V/230V 50-60Hz switchable power supply
Weight: 58 pounds
Dimensions: 7.48” (W) x 16.75” (D) x 24.5” (H)
Power supply: 400W
Environment: Temperature: 40°C (104°F) / 5°C (41°F)
Humidity: 20% - 80%
Supported Formats
Recording format CD
CD-ROM Mode 1, CD-ROM XA Mode 2 (form 1, form 2),
Photo CD, CD-DA (Audio CD), CD-Extra, CD-R, CD-RW
Recording capacity (nominal) CD 700MB
Applicable media
CD
CD-R, CD-RW
Firmware Updates
Occasionally it may be necessary to load updated firmware on to the CWT Series duplicator.
Only those firmware versions recommended and provided by Microboards Technical Support for
this specific product should be installed. Installation of an incorrect firmware on any Microboards
Technology product may result in any remaining warranty being voided.
Technical Support
For technical questions or support issues, contact Microboards Technology technical support:
United States
PH: 952-556-1639
FAX: 952-556-1628
support@microboards.com
www.microboards.com
Please have the Model and Serial Number of your duplicator available when contacting Technical
Support.
PH: +44 (0) 845 230 7800
www.microboards.co.uk
Europe
www.microboards.co.jp
Japan
PH: 03-3561-2266
17
CWT Series MICROBOARDS TECHNOLOGY, LLC
Any unauthorized modification to this equipment may result in the revocation by the FCC of the user’s
authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and antenna
• Connect the equipment into an outlet on a circuit different than that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
This product is in conformity with the EMC Directive (89/336/EEC) through compliance with the following European
standards: EN 55022, EN 55024. The CE mark has been affixed in accordance with the CE Marking Directive
93/68/EEC.
Canadian Department of Communications (DOC) Statement
This Class B digital apparatus complies with the Canadian ICES-003 Issue 4:2004. Cet appareil numerique de la classe B est conforme a
la norme NMB-003 du Canade.
.
18
Loading...