MICREL SY88902 Datasheet
LASER DIODE
DRIVER WTIH
OUTPUT ENABLE
SY88902
FEATURES
■ Up to 1.25Gbps operation
■ 25mA peak drive current
■ Separate modulation control
■ Separate output enable for laser safety
■ Differential inputs for data
■ 75KΩ input pulldown resistor
■ Single power supply
■ Designed for use with SY88903 and SY88904
■ Available in a tiny 10-pin (3mm) MSOP
PIN CONFIGURATIONS
1/EN
D
IN
2
/D
IN
V
REF
R
SET
MSOP
3
K10-1
4
5
10 V
9
8
7
6
CC
OUT
/OUT
GND
GND
DESCRIPTION
The SY88902 is a high speed current switch for driving
a semiconductor laser diode in optical transmission
applications. The output current, or modulation current
IMOD, is DC current controlled by IRSET, current through
the resistor RSET. The output OUT is HIGH when output
enable is HIGH.
The device incorporates complementary open collector
outputs with a capability of driving peak current of 25mA.
The resistor REXT must be placed between /OUT and
VCC to dissipate the worst case power. RSER is
recommended to compensate for laser diode matching
issues.
The SY88902 utilizes the high performance bipolar
ASSET™ technology.
APPLICATIONS
■ 1.25Gbps Gigabit Ethernet
■ 531Mbps and 1062Mbps Fibre Channel
■ 622Mbps SONET
■ Gigabit Interface Converter
BLOCK DIAGRAM
D
DIN
EN
VCC
REXT
OUT
OUT
RSER
Internal Logic
IN
IMOD
to Laser Diode
BIAS
Control
40X
VCC
Modulation Control
GND
VEE
VREF
RSET
RSET
Rev.: C Amendment: /1
1
Issue Date: July 2000
Micrel
SY88902
PIN NAMES TRUTH TABLE
Pin Function
CC Most positive power supply input, +5V for PECL
V
operation.
GND Ground
IN, /DIN These differential PECL 100K compatible inputs
D
receive NRZ data.
/EN This PECL 100K compatible input enables
Laser Driver. Modulation current goes to zero
when asserted HIGH.
OUT, /OUT Open collector outputs from the modulation
buffer drive these differential current outputs.
VREF Voltage reference for use with RSET.
RSET An external resistor sets up the source current
for modulation Imod.
ABSOLUTE MAXIMUM RATINGS
(1)
D D /EN OUT
LHLHL
HLLLH
XXHHL
NOTES:
1. L = LOW, H = HIGH, X = don't care
OUT = OmA
2. H = I
(1)
(2)
/OUT
Symbol Rating Value Unit
VCC Power Supply Voltage 0 to +7.0 V
VI Input Voltage 0 to VCC V
IO Output Current 25 mA
TA Operating Temperature Range 0 to +85 °C
Tstore Storage Temperature Range –55 to +125 °C
P
tot Power Dissipation 250 mW
NOTE:
1. Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded. This is a stress rating only and functional operation is not implied
at conditions other than those detailed in the operational sections of this data sheet. Exposure to ABSOLUTE MAXIMUM RATlNG conditions for extended
periods may affect device reliability.
OPERATIONING CONDITIONS
(1)
Symbol Rating Value Unit
VCC Power Supply Voltage +4.5 to +5.5 V
REXT Resistor to Dissipate Power 10 to 50 Ω
RSER Laser Diode Serial Resistor 0 to 50 Ω
RSET Resistor to Adjust Current 1500 to 50,000 Ω
ΘJA Thermal Resistance of Package to Ambient
OUT Capacitance on OUT + /OUT 2.5 typical pf
C
(2)
206 °C/W
NOTES:
1. The voltage drop across REXT and RSER plus Laser Diode should not be greater than 2V.
2. Still air without heatsink.
2
Micrel
SY88902
DC ELECTRICAL CHARACTERISTICS
GND = 0V; VCC = +5.0V ±10%; TA = 0˚C to + 85˚C
TA = 0°CTA = +25°CTA = +85°C
Symbol Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit
IH Input HIGH Voltage
V
(DIN, /DIN, /EN)
IL Input LOW Voltage VCC-1810 — VCC-1475 VCC-1810 — VCC-1475 VCC-1810 — VCC-1475 mV
V
(DIN, /DIN, /EN)
VREF Reference Voltage — 3.12 ——3.00 ——2.80 — V
IL Input LOW Current
I
(DIN, /DIN, /EN)
IH Input HIGH Current ——100 ——100 ——100 uA
I
(DIN, /DIN, /EN)
ICC Supply Current
OL Output LOW Current ——500 ——500 ——500 uA
I
(2)
(/EN = HIGH)
IOUT Modulation Current 5 15 25 5 15 25 5 15 25 mA
IRSET Modulation Control 0.125 — 0.625 0.125 — 0.625 0.125 — 0.625 mA
RSET =IOUT/IRSET 30 38 44 30 38 44 30 38 44 —
A
NOTES:
1. VI = VIL(Min.)
2. IMOD = 25mA.
VCC-1165 — VCC-880 VCC-1165 — VCC-880 VCC-1165 — VCC-880
(1)
0.5 —— 0.5 —— 0.5 ——uA
— 16 25 — 16 25 — 16 25 mA
mV
AC ELECTRICAL CHARACTERISTICS
(1)
IMOD =10mA; GND = 0V; VCC = +5V ±10%; TA = 0˚C to + 85˚C
TA = 0°CTA = +25°CTA = +85°C
Symbol Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit Conditions
pd D Propagation Delay ——1000 — 500 1000 ——1000 ps IMOD = 10mA
t
DIN - OUT
pd EN Propagation Delay ——1000 — 450 1000 ——1000 ps IMOD = 10mA
t
/EN - OUT
r Rise/Fall Time — 200 ——200 ——200 — ps
t
tf (20% to 80%)
OR Output Current Ringing
I
NOTES:
1. REXT = RSER = 50Ω ±1%, RSER connects to VCC directly without Laser Diode.
2. IOH = 5 to 25mA
(2)
——10 ——10 ——10 %
3
Loading...