MICREL SY10E116, SY100E116 Datasheet

QUINT DIFFERENTIAL
LINE RECEIVER

SY10E116

SY100E116

FEATURES

■ 450ps max. Propagation Delay

■ Extended 100E V

EE range of –4.2V to –5.5V

■ VBB output for single-ended reception

■ Fully compatible with industry standard 10KH,

100K I/O levels

■ Internal 75KΩ input pulldown resistors

■ Fully compatible with Motorola MC10E/100E116

■ Available in 28-pin PLCC package

BLOCK DIAGRAM

D0
D0
D1
D1
D2
D2

Q0
Q0
Q1
Q1
Q2
Q2

DESCRIPTION

The SY10/100E116 are quint differential line receivers
designed for use in new, high-performance ECL systems.
These devices have emitter-follower outputs and an
internally generated reference supply (V
ended reception.

Active current sources combined with Micrel-Synergy’s
ASSET™ technology provide the receivers with excellent
common mode noise rejection.

The receiver design features clamp circuitry to cause a
defined output state if both the inverting and non-inverting
inputs are left open; in this case the Q output goes LOW,
while the Q output goes HIGH.

If both inverting and non-inverting inputs are at equal
potential, the receiver does

not go

to a defined state, but
rather shares current in normal differential amplifier fashion,
producing output voltage levels midway between HIGH
and LOW.

The VBB output is intended for use as a reference
voltage for single-ended reception of ECL signals to that
device only. When using VBB for this purpose, it is
recommended that VBB is decoupled to VCC via a 0.01 µF
capacitor.

For higher bandwidth, please refer to the SY10/100E416
device.

BB) for single-

D3
D3
D4
D4

VBB

Q3
Q3
Q4
Q4

PIN NAMES

Pin Function

D0, D0-D4, D4 Differential Input Pairs
Q0, Q0-Q4, Q4 Differential Output Pairs
VBB Reference Voltage Output

CCO VCC to Output

V

PIN CONFIGURATION

3

4

4

D

D

D

24 23 22 21 20 19

25

D

D

V
V

26

3

27

D

2

28

2

EE

1

BB

2

D
D

3

0
0

4

56789

1

D

PLCC

TOP VIEW

J28-1

1

D

CCO

V

CCO

V

0

Q

4

Q

0

Q

4

Q

10 11

CCO

V

CCO

V

1

Q

18

Q

3

17

Q

3

16

V

CC

15

Q

2

14

Q

2

13

V

CCO

12

Q

1

Rev.: E Amendment: /0

1

Issue Date: November, 1998

SY10E116

Micrel

SY100E116

LOGIC EQUATION

Qn = Dn

DC ELECTRICAL CHARACTERISTICS

VEE = VEE(Min.) to VEE(Max.); VCC = VCCO = GND

TA = –40°CTA = 0°CTA = +25°CTA = +85°C

Symbol Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit

BB Output Reference V

V

Voltage 10E –1.43 —–1.30 –1.38 —–1.27 –1.35 —–1.25 –1.31 —–1.19

100E –1.43 —–1.26 –1.38 —–1.26 –1.38 —–1.26 –1.38 —–1.26

IIH Input HIGH Current ——200 ——200 ——200 ——200 µA
IEE Power Supply Current mA

10E — 29 35 — 29 35 — 29 35 — 29 35

100E — 29 35 — 29 35 — 29 35 — 33 40

VPP (DC) Input Sensitivity

CMR Common Mode Range

V

NOTES:

1. VPP is the minimum differential input voltage required to assure full ECL levels are present at the outputs.

2. VCMR is referenced to the most positive side of the differential input signal. Normal operation is obtained when the "HIGH" input is within the VCMR range
and the input swing is greater than VPP (min.) and <1V.

(1)

150 ——150 ——150 ——150 ——mV

(2)

–2.0 —–0.6 –2.0 —–0.6 –2.0 —–0.6 –2.0 —–0.6 V

AC ELECTRICAL CHARACTERISTICS

VEE = VEE(Min.) to VEE(Max.); VCC = VCCO = GND

TA = –40°CTA = 0°CTA = +25°CTA = +85°C

Symbol Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit

PLH Propagation Delay to ps

t
tPHL Output D 150 300 500 200 300 450 200 300 450 200 300 450

D (S.E.) 150 300 550 150 300 500 150 300 500 150 300 500

VPP (DC) Input Sensitivity

skew Within-Device Skew

t

Dn to Qn, Qn

tskew Duty Cycle Skew

tPLH – tPHL

tr Rise/Fall Time 250 375 625 275 375 575 275 375 575 275 375 575 ps
tf 20% to 80%

NOTES:

1. Minimum input swing for which AC parameters are guaranteed.

2. Within-device skew is defined as identical transitions on similar paths through a device.

3. Duty cycle skew is defined only for differential operation when the delays are measured from the cross point of the inputs to the cross point of the
outputs.

(1)

(3)

150 — 150 150 ——150 ——150 ——mV

(2)

— 50 ——50 ——50 ——50 — ps

— ±10 ——±10 ——±10 ——±10 — ps

PRODUCT ORDERING CODE

Ordering Package Operating

Code Type Range

SY10E116JC J28-1 Commercial
SY10E116JCTR J28-1 Commercial
SY100E116JC J28-1 Commercial
SY100E116JCTR J28-1 Commercial

Ordering Package Operating

Code Type Range

SY10E116JI J28-1 Industrial
SY10E116JITR J28-1 Industrial
SY100E116JI J28-1 Industrial
SY100E116JITR J28-1 Industrial

2