Micrel MICRF103 DATA SHEET

MICRF103 Micrel

MICRF103

QwikRadio™ UHF ASK Transmitter

Final

General Description

The MICRF103 is a single chip Transmitter IC for remote
wireless applications. The device employs Micrel’s latest
QwikRadio™ technology. This device is a true ”data-in,
antenna-out” monolithic device. All antenna tuning is accom­plished automatically within the IC which eliminates manual
tuning, and reduces production costs. The result is a highly
reliable yet extremely low cost solution for high volume
wireless applications. Because the MICRF103 is a true
single-chip radio transmitter, it is easy to apply, minimizing
design and production costs, and improving time to market.

The MICRF103 uses a novel architecture where the external
antenna is tuned by the internal UHF synthesizer. This
transmitter is designed to comply worldwide UHF unlicensed
band international radio regulations. The IC is compatible
with virtually all ASK/OOK (Amplitude Shift Keying/On-Off
Keyed) UHF receiver types from wide-band super-regenera­tive radios to narrow-band, high performance super-hetero­dyne receivers. The transmitter is designed to work with
transmitter data rates up to 115k bits per second.

The automatic tuning in conjunction with an external resistor,
insures that the transmitter output power stays constant at
maximum regulatory transmit power limits for the life of the
battery.

When coupled with Micrel’s family of QwikRadio™ receivers,
the MICRF103 provides the lowest cost and most reliable
remote actuator and RF link system available.

Features

• Complete UHF transmitter on a monolithic chip

• Frequency range 800MHz to 1GHz

• Data rates to 115kbps

• Automatic antenna alignment, no manual adjustment

• Low external part count

• Low standby current <1µA

Applications

• Remote keyless entry systems (RKE)

• Remote fan/light control

• Garage door opener transmitters

• Remote sensor data links

Ordering Information

Part Number Temperature Range Package

MICRF103BM –40°C to +85°C 8-Pin SOIC

T ypical Application

+5V

ASK DATA INPUT

4.7µF

RP1

0.1µF

Note: Example for 868MHz

100k

RP2

6.8k

Y1

MICRF103

PC
VDD

VSS
REFOSC

+5V

ASK

ANTP

ANTM

STBY

8.2pF

100pF

100k

Figure 1

QwikRadio is a trademark of Micrel, Inc. The QwikRadio ICs were developed under a partnership agreement with AIT of Orlando, Florida.

Micrel, Inc. • 1849 Fortune Drive • San Jose, CA 95131 • USA • tel + 1 [phone] • fax + 1 [phone] • http://www.micrel.com

June 2002 1 MICRF103

1.0pF

10nH

27nH

27nH

1.0pF

SAW Filter

50Ω

Monopole

PCB Antenna

MICRF103 Micrel

Pin Configuration

VDD

VSS

REFOSC

Pin Description

Pin Number Pin Name Pin Function

1 PC Power Control Input. The voltage at this pin should be set between 0.1V to

2 VDD Positive power supply input for the IC.
3 VSS This pin is the ground return for the IC. A power supply bypass capacitor

4 REFOSC This is the timing reference frequency which is the transmit frequency

5 STBY Input for transmitter stand-by control pin is pulled to VDD for transmit

6 ANTM Negative RF power output to drive one side of the transmit antenna.
7 ANTP Positive RF power output to drive the other side of the transmit antenna.
8 ASK Amplitude Shift Key modulation data input pin. For CW operation, connect

1PC
2
3
4

8 ASK
7

ANTP
ANTM

6

STBY

5

MICRF103BM

0.4V for normal operation.

connected from VDD to VSS should have the shortest possible path.

divided by 64. Connect a crystal (mode dependent) between this pin and
VSS, or drive the input with an AC coupled 0.5Vpp input clock. See

ence Oscillator

operation and VSS for stand-by mode.

this pin to VDD.

section in this data sheet under

Electrical Characteristics.

Refer-

MICRF103 2 June 2002

MICRF103 Micrel

Absolute Maximum Ratings (Note 1)

Supply Voltage(V

Voltage on I/O Pins ............................. V

Storage Temperature Range ...................-65°C to + 150°C

Lead Temperature (soldering, 10 seconds) ........... + 300°C

ESD Rating, Note 3

) .....................................................+6V

DD

–0.3 to VDD+0.3

SS

Operating Ratings (Note 2)

Supply Voltage (V

Maximum Supply Ripple Voltage ...............................10mV

PC Input Range......................................0.1V < VPC < 0.4V

Ambient Operating Temperature (TA) ........ –40°C to +85°C

Programmable Transmitter Frequency Range:

) .................................... 4.75V to 5.5V

DD

........................................................ 800MHz to 1GHz

Electrical Characteristics

Specifications apply for 4.75V < VDD < 5.5V, VPC = 0.35V, TA = 25°C, freq
–40°C ≤ TA ≤ 85°C unless otherwise noted.

Parameter Condition Min Typ Max Units
Power Supply

Standby Supply Current, I
MARK Supply Current, I

SPACE Supply Current, I

MARK/SPACE Ratio 33%@868MHz 16 mA

RF Output Section and Modulation Limits:

Maximum Power Level, P

Output Power Variation over supply and temperature ±2 dBm
Extinction ratio for ASK 38 45 dBc
Varactor tuning range Note 5 2.6 3.0 3.3 pF

Reference Oscillator Section

Reference Oscillator Input 300 kΩ
Impedance

Reference Oscillator Source 5.0 µA
Current

Reference Oscillator Input 0.2 1.0 V
Voltage (peak-to-peak)

Digital / Control Section

Calibration Time note 7, ASK=HIGH 20 ms
Power Amplifier Output Hold-off note 4, STDBY transition from LOW to HIGH 5 ms

Time from STBY crystal, ESR < 20Ω
Transmitter Stabilization Time from external reference (500mVpp) 9 ms
From STBY crystal, ESR < 20Ω 12 ms
Maximum Data rate

- ASK modulation duty cycle of the modulating signal = 50% 115 kbits/s
STBY HIGH V
STBY LOW V
ASK Pin VIH, input high voltage 0.8V

ASK Input Current ASK = 0V, 5.0V input current –10 0.1 10 µA

Q

ON

OFF

OUT

V

< 0.5V 0.10 µA

STBY

@868MHz 19 26.5 mA
@915MHz 20 27.5 mA
@868MHz 14 18 mA
@915MHz 15 21 mA

33%@915MHz 17 mA

@868MHz (EIRP) -3 dBm
@915MHz (EIRP) -3 dBm

enable voltage 0.8V

IH

IL

VIL, input low voltage 0.1V

= 13.5625MHz, STBY = VDD. Bold values indicate

REFOSC

DD

DD

0.1V

DD

DD

PP

V

V
V

June 2002 3 MICRF103