Michigan Wheel engine Owner’s Manual

Propeller

Shaft
Taper

A

Forward

Thrust

Washer

B

Cushion

Hub

C

Aft Drive Adapter

D

Reuse OEM Cotter Pin

(not included with hub kit)

Reuse OEM Propeller Nut

(not included with hub kit)

Reuse OEM Flat Washer if

not included with hub kit

OR

Aft Drive Adapter

D

Nylock Nut

and

Image is for reference only. Actual components vary depending on

application. Please consult owner’s manual as necessary.

Forward End Aft End

Locking Tab Washer

(included with select hub kits)

!IMPORTANT!

To avoid accidental engine starting while servicing propeller, it is recommended to set the gear selector to neutral and to disconnect all spark plug wires before any propeller service procedure.

Refer to Engine Owner’s Manual for important safety precautions when installing propeller.

1. Remove old propeller and hardware. Use block of wood between gearcase and propeller to hold propeller during propeller
nut removal, if necessary. The propeller shaft taper (A) must be visible. If the propeller shaft taper is not visible, the forward
thrust washer may still be in place. If the forward thrust washer is difcult to remove, lightly tap with dead blow hammer or
rubber mallet to loosen. Rock forward thrust washer back and forth to remove. Clean propeller shaft with shop rag and inspect
propeller shaft seal for cracks or leaks. Consult owner’s manual if service is required.

2. Apply marine grease to propeller shaft to aid future removal of propeller and hardware.

3. Install supplied forward thrust washer (B). The taper of the thrust washer must nest with the taper on the propeller shaft and
should slide into place with little effort. The thrust washer part number should be clearly visible at this point when thrust
washer is correctly installed. NEVER INSTALL A PROPELLER WITHOUT A FORWARD THRUST WASHER. SEVERE
DAMAGE CAN OCCUR TO ENGINE GEARCASE AND/OR PROPELLER.

4. Insert cushion hub (C) into propeller bushing cavity. Cushion hub is tapered and will only t one way. The cushion hub
should drop into propeller bushing cavity leaving no more than approximately 0.375” (3/8 inch) exposed and, in some cases,
will drop into bushing cavity completely. Press rmly or gently tap as required with dead blow hammer or rubber mallet until
forward end of cushion hub is slightly below forward end of bushing cavity. This will help to guide the forward thrust washer
into location during nal assembly.

5. Install aft drive adapter (D) through small hole in aft end of propeller and align with slots in cushion hub. Firmly press drive
adapter into cushion hub.

6. Slide propeller, cushion hub, and drive adapter assembly onto propeller shaft while simultaneously rotating assembly until the
drive adapter splines mesh with the propeller shaft spline. Slide assembly forward until it contacts forward thrust washer.

7. Install washer and propeller nut as indicated above. Use block of wood between gearcase and propeller and torque propeller
nut (consult engine owner’s manual for proper torque specication). Secure nut by bending locking tabs into drive adapter
slots or installing cotter pin.

8. Inspect installation. Propeller must spin freely and not rub gearcase. Propeller should be securely held between forward thrust
washer (B) and aft drive adapter (D) when properly installed.

9. Reconnect spark plug wires.

10. Check propeller for tightness every 20 hours of operation.

Michigan Wheel warrants to the original consumer purchaser and original motor
 tted, that for a period of one year from the date of purchase, the body of the Michigan Match®,
Vortex®, Apollo® or Ballistic® propeller will be free of any defect in material or
workmanship that results in blade or hub fracture or failure under normal pleasure boat
usage. Michigan Wheel also warrants to the original consumer purchaser, under the same
parameters of use described above, that the propeller bushing, including XHS®/XHS II® hub kit
components, will be free from any defect in material or workmanship for a period of one year from
the date of purchase. Proof of purchase required for all warranty claims.

Some surface discoloration of propellers and hardware is unavoidable, and will not be covered by
this warranty. This warranty also does not cover normal wear, accidental damage, modi cation,
improper installation, improper maintenance, or other circumstances that are not the direct result
of a defect in the material or workmanship of the propeller.

The sole obligation of Michigan Wheel under this warranty is to repair or
replace the propeller, in the sole discretion of Michigan Wheel, and at its expense. In
order to make a replacement claim, please contact the Michigan Wheel Customer Service
Department, at [phone], for a “Return Materials Authorization” number (RMA#), and
shipping instructions. The RMA# is to be indicated along with our given address on the label, and
the shipping carton should include your return shipping address, your phone number, and a copy
of your original purchase receipt. The warranty will not cover any expense of propeller removal,
shipping, or reinstallation of the propeller.

The above warranty is Michigan Wheel’s sole warranty for the Michigan Match®,
Vortex®, Apollo® or Ballistic® propellers as well as XHS®/XHS II® hub kits. Michigan
Wheel expressly disclaims all other warranties, expressed or implied, including, without
limitation, the warranties of merchantability and  tness for a particular purpose and excludes all
liability for incidental or consequential damages, loss of use of the propeller, costs, and expenses.

Any actions arising out of this warranty and the sale of this product shall be governed by Michigan
law and may only be brought, heard and decided in Kent County Circuit Court, in the State of
Michigan, U.S.A., or in the United States District Court for the Western District of Michigan.

Limited Warranty

Michigan Wheel

1501 Buchanan Avenue S.W.

Grand Rapids, MI 49507

Phone: [phone]

Warranty 991010-C

Form 990445-C